Download

PDF Abstract Text:

CD54 / 74HC138, CD54 / 74HCT138, CD54 / 74HC238, CD54 / 74HCT238

October 1997 - Revised May 2003

CD54 / 74HC138, CD54 / 74HCT138, CD54 / 74HC238, CD54 / 74HCT238
Data sheet acquired from Harris Semiconductor SCHS147F
October 1997 - Revised May 2003
High-Speed CMOS Logic 3- to 8-Line Decoder / Demultiplexer Inverting and Non-Inverting
Description
Features
· Select One Of Eight Data Outputs Active Low for 138, Active High for 238
/ Title (CD74 HC138 , CD74 HCT13 8, CD74 HC238 , CD74 HCT23 8) / Subject (High Speed
Ordering Information
PART NUMBER CD54HC138F3A CD54HC238F3A CD54HCT138F3A CD54HCT238F3A CD74HC138E CD74HC138M TEMP. RANGE (oC) -55 to 125 -55 to 125 -55 to 125 -55 to 125 -55 to 125 -55 to 125 -55 to 125 -55 to 125 -55 to 125 -55 to 125 -55 to 125 -55 to 125 -55 to 125 -55 to 125 -55 to 125 -55 to 125 -55 to 125 -55 to 125 PACKAGE 16 Ld CERDIP 16 Ld CERDIP 16 Ld CERDIP 16 Ld CERDIP 16 Ld PDIP 16 Ld SOIC 16 Ld SOIC 16 Ld PDIP 16 Ld SOIC 16 Ld SOIC 16 Ld SOP 16 Ld TSSOP 16 Ld TSSOP 16 Ld PDIP 16 Ld SOIC 16 Ld SOIC 16 Ld PDIP 16 Ld SOIC
Pinout
CD54HC138, CD54HCT138, CD54HC238, CD54HCT238 (CERDIP) CD74HC138, CD74HCT138, CD74HCT238 (PDIP, SOIC) CD74HC238 (PDIP, SOIC, SOP, TSSOP) TOP VIEW
A0 1 A1 2 A2 3 E1 4 E2 5 E3 6 (Y7) Y7 7 GND 8 16 VCC 15 Y0 (Y0) 14 Y1 (Y1) 13 Y2 (Y2) 12 Y3 (Y3) 11 Y4 (Y4) 10 Y5 (Y5) 9 Y6 (Y6)
CD74HC138M96 CD74HC238E CD74HC238M CD74HC238M96 CD74HC238NSR CD74HC238PW CD74HC238PWR CD74HCT138E CD74HCT138M CD74HCT138M96 CD74HCT238E CD74HCT238M
NOTE: When ordering, use the entire part number. The suffixes 96 and R denote tape and reel.
CAUTION: These devices are sensitive to electrostatic discharge. Users should follow proper IC Handling Procedures. Copyright
CD54 / 74HC138, CD54 / 74HCT138, CD54 / 74HC238, CD54 / 74HCT238 Functional Diagram
CD54 / 74HC138, CD54 / 74HCT138, CD54 / 74HC238, CD54 / 74HCT238
Absolute Maximum Ratings
Thermal Information
Operating Conditions
CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE: 1. The package thermal impedance is calculated in accordance with JESD 51-7.
DC Electrical Specifications
CD54 / 74HC138, CD54 / 74HCT138, CD54 / 74HC238, CD54 / 74HCT238
DC Electrical Specifications
VCC (V)
5.5 5.5 4.5 to 5.5
HCT Input Loading Table
INPUT A0-A2 E1, E2 E3 UNIT LOADS 1.5 1.25 1
NOTE: Unit Load is ICC limit specified in DC Electrical Table, e.g., 360µA max at 25oC.
TEST CONDITIONS 25oC VCC (V) MIN TYP MAX -40oC TO 85oC MIN MAX -55oC TO 125oC MIN MAX UNITS
PARAMETER HC TYPES Propagation Delay Address to Output
SYMBOL
CD54 / 74HC138, CD54 / 74HCT138, CD54 / 74HC238, CD54 / 74HCT238
PARAMETER Enable to Output HC / HCT138
SYMBOL
TEST CONDITIONS
Test Circuits and Waveforms
INVERTING OUTPUT
FIGURE 7. HC AND HCU TRANSITION TIMES AND PROPAGATION DELAY TIMES, COMBINATION LOGIC
FIGURE 8. HCT TRANSITION TIMES AND PROPAGATION DELAY TIMES, COMBINATION LOGIC
MECHANICAL
MPDI002C - JANUARY 1995 - REVISED DECEMBER 20002
N (R-PDIP-T)
16 PINS SHOWN
PLASTIC DUAL-IN-LINE PACKAGE
PINS DIM A 16 9 A MAX
MS-100 VARIATION
1 0.070 (1, 78) 0.045 (1, 14) D
0.045 (1, 14) 0.030 (0, 76) D
0.020 (0, 51) MIN
0.325 (8, 26) 0.300 (7, 62) 0.015 (0, 38) 0.200 (5, 08) MAX Seating Plane 0.125 (3, 18) MIN 0.010 (0, 25) NOM Gauge Plane
0.100 (2, 54) 0.021 (0, 53) 0.015 (0, 38) 0.010 (0, 25) M
0.430 (10, 92) MAX
14 / 18 PIN ONLY 20 pin vendor option
D 4040049 / E 12 / 2002
NOTES: A. All linear dimensions are in inches (millimeters). B. This drawing is subject to change without notice. C. Falls within JEDEC MS-001, except 18 and 20 pin minimum body lrngth (Dim A). D. The 20 pin end lead shoulder width is a vendor option, either half or full width.
POST OFFICE BOX 655303
· DALLAS, TEXAS 75265
MECHANICAL DATA
MSOI002B - JANUARY 1995 - REVISED SEPTEMBER 2001
D (R-PDSO-G)
8 PINS SHOWN 0.050 (1, 27) 8 5 0.020 (0, 51) 0.014 (0, 35) 0.010 (0, 25)
PLASTIC SMALL-OUTLINE PACKAGE
0.008 (0, 20) NOM
Gage Plane 1 A 4 0°- 8° 0.044 (1, 12) 0.016 (0, 40)
Seating Plane 0.069 (1, 75) MAX 0.010 (0, 25) 0.004 (0, 10) 0.004 (0, 10)
PINS DIM A MAX A MIN
4040047 / E 09 / 01 NOTES: A. B. C. D. All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion, not to exceed 0.006 (0, 15). Falls within JEDEC MS-012
POST OFFICE BOX 655303
· DALLAS, TEXAS 75265
MECHANICAL DATA
MTSS001C - JANUARY 1995 - REVISED FEBRUARY 1999
PW (R-PDSO-G)
14 PINS SHOWN
PLASTIC SMALL-OUTLINE PACKAGE
0, 15 NOM 4, 50 4, 30 6, 60 6, 20 Gage Plane 0, 25 1 A 7 0°- 8° 0, 75 0, 50
Seating Plane 1, 20 MAX 0, 15 0, 05 0, 10
PINS DIM A MAX
4040064 / F 01 / 97 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0, 15. Falls within JEDEC MO-153
POST OFFICE BOX 655303
· DALLAS, TEXAS 75265
Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265
Copyright 2003, Texas Instruments Incorporated