VOLTAGE 8-BIT MCUs WITH CONVERTER PINS 3.9V Supply Operating Rang

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

VOLTAGE 8-BIT MCUs WITH CONVERTER PINS 3.9V Supply Operating Rang

Datasheet Thumbnail

Top Searches for this datasheet

ST6208L/09L ST6210L/20L
VOLTAGE 8-BIT MCUs WITH CONVERTER PINS
3.9V Supply Operating Range Maximum Clock Frequency +70°C Operating Temperature Range Run, Wait Stop Modes Interrupt Vectors Look-up Table capability Program Memory Data Storage Program Memory: User selectable size Data RAM: 64bytes pins, fully programmable Input with pull-up resistor Input without pull-up resistor Input with interrupt generation Open-drain push-pull output Analog Input (except ST6208L) lines sink 12mA drive LEDs 8-bit Timer/ Counter with 7-bit programmable prescaler Digital Watchdog 8-bit Converter with analog inputs On-chip Clock oscillator driven Quartz Crystal Ceramic resonator network Power-on Reset external Non-Maskable Interrupt ST626x-EMU2 Emulation Development System (connects MS-DOS RS232 serial line)
PDIP20
PSO20
(See Datasheet Ordering Information)
DEVICE SUMMARY
DEVICE ST62T08L ST62T09L ST62T10L ST62T20L
(Bytes)
Pins
Analog inputs
1036 1036 1836 3884
Rev.
November 1997
1/10
ST6208L/09L ST6210L/20L
GENERAL DESCRIPTION
INTRODUCTION ST6208L/09L/10L/20L voltage mask programmed version ST62T08C/T09C/ T10C/T20C devices. They offer same functionality devices, selecting options options defined programmable option byte version, with exception Reset that available. Figure Programming wave form READOUT PROTECTION READOUT PROTECTION option selected, protection fuse blown prevent access program memory content. case user wants blow this fuse, high voltage must applied TEST pin.
Figure Programming Circuit
100nF
100mA
ROTE 100nF
VR02003
VR02001
Note: ZPD15 used overvoltage protection
2/10
ST6208L/09L ST6210L/20L
ST6208L/09L/10L/20L MICROCONTROLLER OPTION LIST Customer Address Contact Phone Reference
SGS-THOMSON Microelectronics references DeviLe: ST6208L ST6209L ST6210L ST6220L Package: Dual Line Plastic Small Outline Plastic with conditionning: Standard (Stick) Tape Reel Temperature Range: 70°C Special Marking: Authorized characters letters, digits, '.', '-', spaces only. Maximum character count: DIP20: SO20: Oscillator Source Selection: Crystal Quartz/Ceramic resonator Network Watchdog Selection: Software Activation Hardware Activation Readout Protection: Disabled (Fuse cannot blown) Enabled (Fuse blown customer) Note: part delivered with protected ROM. fuse must blown protection effective. External STOP Mode Control[ Enabled TIMER pull-up Enabled pull-up Enabled Disabled Disabled Disabled
Comments Supply Operating Range application: Oscillator Fequency application: Notes Signature Date
3/10
ST6208L/09L ST6210L/20L
ORDERING INFORMATION following section deals with procedure transfer customer codes SGS-THOMSON. 1.3.1 Transfer Customer Code Customer code made contents list selected mask options. contents sent diskette, electronic means, with hexadecimal file generated development tool. unused bytes must FFh. selected mask options communicated SGS-THOMSON using correctly filled OPTION LIST appended. 1.3.2 Listing Generation Verification When SGS-THOMSON receives user's contents, computer listing generated from This listing refers exactly mask which will used produce specified MCU. listing then returned customer must thoroughly check, complete, sign return SGS-THOMSON. signed listing forms part contractual agreement creation specific customer mask. SGS-THOMSON Sales Organization will pleased provide detailed information contractual points. Table Memory ST6208L,09L
Device Address 0000h-0B9Fh 0BA0h-0F9Fh 0FA0h-0FEFh 0FF0h-0FF7h 0FF8h-0FFBh 0FFCh-0FFDh 0FFEh-0FFFh Description Reserved User Reserved Interrupt Vectors Reserved Interrupt Vector Reset Vector
Table Memory ST6210L
Device Address 0000h-087Fh 0880h-0F9Fh 0FA0h-0FEFh 0FF0h-0FF7h 0FF8h-0FFBh 0FFCh-0FFDh 0FFEh-0FFFh Description Reserved User Reserved Interrupt Vectors Reserved Interrupt Vector Reset Vector
Table Memory ST6220L
Device Address 0000h-007Fh 0080h-0F9Fh 0FA0h-0FEFh 0FF0h-0FF7h 0FF8h-0FFBh 0FFCh-0FFDh 0FFEh-0FFFh Description Reserved User Reserved Interrupt Vectors Reserved Interrupt Vector Reset Vector
Table version Ordering Information
Sales Type ST6208LB1/XXX ST6208LM1/XXX ST6209LB1/XXX ST6209LM1/XXX ST6210LB1/XXX ST6210LM1/XXX ST6220LB1/XXX ST6220LM1/XXX 3884 Bytes 1036 Bytes +70°C 1836 Bytes PDIP20 PSO20 PDIP20 PSO20 1036 Bytes None Analog input Temperature Range Package PDIP20 PSO20 PDIP2 PSO20
4/10
ST6208L/09L ST6210L/20L
ELECTRICAL CHARACTERISTICS
ABSOLUTE MAXIMUM RATINGS This product contains devices protect inputs against damage high static voltages, however advisable take normal precaution avoid application voltage higher than specified maximum rated voltages. proper operation recommended that higher than lower than VDD. Reliability enhanced unused inputs connected appropriate logic voltage level VSS). Power Considerations.The average chip-junction temperature, Celsius obtained from: Tj=TA RthJA Where:TA Ambient Temperature. RthJA =Package thermal resistance (junction-to ambient). Pint Pport. Pint =IDD (chip internal power). Pport =Port power dissipation (determined user).
Value -0.3
Symbol IVDD IVSS TSTG Supply Voltage Input Voltage Output Voltage
Parameter
Unit
Current Drain Excluding VDD, Total Current into (source) Total Current (sink) Junction Temperature Storage Temperature
0.3(1)
Notes: Stresses above those listed "absolute maximum ratings" cause permanent damage device. This stress rating only functional operation device these conditions implied. Exposure maximum rating conditions extended period affect device reliability. Within these limits clamping diodes guarantee conductive. Voltages outside these limits authorised long injection current kept within specification.
5/10
ST6208L/09L ST6210L/20L
RECOMMENDED OPERATING CONDITIONS
Symbol fOSC IINJ+ IINJParameter Operating Temperature Operating Supply Voltage Oscillator Frequency Injection Current (positive) Test Conditions Suffix Version fOSC 2MHz fOSC 4MHz 2.4V 3.0V 3.9V Value Min. Typ. Max. Unit
Injection Current (negative) 3.9V
Notes: Care must taken case negative current injection, where adapted impedance must respected analog sources affect conversion. -1mA injection, maximum recommended. 2.An oscillator frequency above 1MHz recommended reliable results
Figure Maximum Operating FREQUENCY (Fmax) Versus SUPPLY VOLTAGE
Maximum FREQU ENCY (MHz)
FUNCTION ALITY GUARANTEED THIS AREA
SUPPLY VOLTAGE (VDD)
shaded area outside recommended operating range; device functionality guaranteed under these conditions.
6/10
ST6208L/09L ST6210L/20L
ELECTRICAL CHARACTERISTICS +70°C unless otherwise specified)
Symbol Parameter Test Conditions Value Min. Typ. Max. Unit
VHys
Input Level Voltage Input pins Input High Level Voltage Input pins Hysteresis Voltage Input pins Level Output Voltage Output pins
VDD= VDD= 3.0V; +10µA VDD= 3.0V; 3.0mA VDD= 2.4V; 1.5mA VDD= 3.0V; +10µA VDD= 3.0V; VDD= 3.0V; +12mA VDD= 2.4V; VDD= 3.0V; -10µA VDD= 3.0V; -1.5mA VDD= 2.4V; -10µA Input pins RESET Pull-Up configured) VRESET=VSS fOSC=4MHz VDD=3.0V fINT=4MHz VDD=3.0V ILOAD=0mA VDD=3.0V fINT=4MHz
Level Output Voltage Sink pins High Level Output Voltage Output pins Pull-up Resistance Input Leakage Current Input pins RESET Input Leakage Current RESET Supply Current RESET Mode Supply Current Mode Supply Current WAIT Mode Supply Current STOP Mode(3)
1200
Notes: Hysteresis voltage between switching levels peripherals running peripherals stand-by
7/10
ST6208L/09L ST6210L/20L
ELECTRICAL CHARACTERISTICS(Cont'd) ELECTRICAL CHARACTERISTICS ((TA +70°C unless otherwise specified
Symbol tREC Parameter Supply Recovery Time Internal frequency with oscillator Input Capacitance Output Capacitance VDD=3.0V R=47k R=100k R=470k Inputs Pins Outputs Pins Test Conditions Value Min. Typ. Max. Unit
Notes: Period which connected allow internal Reset function next power-up. oscillator frequency above 1MHz recommended reliable results. Measure performed with OSCin soldered PCB, with around equivalent capacitance.
8/10
ST6208L/09L ST6210L/20L
CONVERTER CHARACTERISTICS +70°C unless otherwise specified)
Symbol ATOT Parameter Resolution Total Accuracy Conversion Time Zero Input Reading Full Scale Reading fOSC fOSC fOSC fOSC fOSC 1.2MHz, VDD=3.0V 1.2MHz, VDD=2.4V 32kHz, VDD=3.0V 2MHz Test Conditions Min. Value Typ. Max. Unit
Conversion result when Conversion result when
Analog Input Current During VDD= 4.0V Conversion Analog Input Capacitance
Notes: Noise VDD, <10mV oscillator frequencies less than 1MHz, Converter accuracy decreased.
TIMER CHARACTERISTICS ((TA +70°C unless otherwise specified)
Symbol Parameter Test Condi tions Min. Value Typ. Max. Unit
Input Frequency TIMER Pulse Width TIMER 2.4V
9/10
ST6208L/09L ST6210L/20L
Notes:
Information furnished believed accurate reliable. However, SGS-THOMSON Microelectronics assumes responsibility consequences such information infringement patents other rights third parties which result from use. license granted implication otherwise under patent patent rights SGS-THOMS Microelectronics. Specification mentioned this publication subject change without notice. This publication supersedes replaces information previously supplied. SGS-THOMSON Microelectronics products authorized critical components support devices systems without express written approval SGS-THOMSON Microelectronics. ©1997 SGS-THOMSON Microelectronics -Printed Italy Rights Reserved. SGS-THOMSON Microelectronics GROUP COMPANIES Australia Brazil Canada China France Germany Italy Japan Korea Malaysia Malta Morocco Netherlands Singapore Spain Sweden Swit zerland Taiwan Thailand United Kingdom U.S.A.
10/10

VOLTAGE 8-BIT MCUs WITH CONVERTER PINS 3.9V Supply Operating Rang

Top Searches for this datasheet

Other recent searches