SDM-09120 925-960 Class 120W Power Amplifier Module Product

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

SDM-09120 925-960 Class 120W Power Amplifier Module Product

Datasheet Thumbnail

Top Searches for this datasheet

Product Description SDM-09120 120W power module impedance matched, single-stage, push-pull Class amplifier module suitable power amplifier driver output stage. drop-in, no-tune solution high power applications requiring high efficiency, excellent linearity, unit-to-unit repeatability.
SDM-09120
925-960 Class 120W Power Amplifier Module
Product Features
+28V
Vds1
Balun RFin Balun
impedance 120W Output P1dB negative supply required High Gain: Typical High Efficiency Protection: JEDEC Class (2000V HBM)
Applications
+28V
Base Station driver Repeater CDMA EDGE
Specifications Symbol Frequency P1dB Gain Gain Flatness Variation
Parameters Frequency Operation Output Power Compression, 120W Output Power, 942MHz 943MHz Peak-to-Peak Gain Variation, 120W PEP, 960MHz Input Return Loss, 120W Output Power, 960MHz Order Product. 120W Output, 942MHz 943MHz 120W Output, Change Spacing 100KHz 25MHz Drain Efficiency, 120W Output, 942MHz 943MHz Efficiency Drain Efficiency, 120W Output, 943MHz Delay Signal Delay from Phase Linearity Deviation from Linear Phase (Peak-to-Peak) Test Conditions Zout 28.0V, IDQ1 IDQ2 =500mA TFlange
Units
Min.
Typ.
Max.
information provided herein believed reliable press time. Sirenza Microdevices assumes responsibility inaccuracies ommisions. Sirenza Microdevices assumes responsibility this information, such information shall entirely user's risk. Prices specifications subject change without notice. patent rights licenses circuits described herein implied granted third party. Sirenza Microdevices does authorize warrant Sirenza Microdevices product life-support devices and/or systems. Copyright 2005 Sirenza Microdevices, Inc. worldwide rights reserved.
Technology Court, Broomfield, 80021
Phone: (800) SMI-MMIC
http://www.sirenza.com EDS-103478
SDM-09120 925-960 120W Power Module
Description Function 2,4,7,9 Flange VGS1 Ground Input VGS2 Output Ground Module Topside ground. Internally blocked LDMOS gate bias. VGSTH VDC. Notes LDMOS drain bias. Note Internally blocked LDMOS drain bias. Note Baseplate provides electrical ground thermal transfer path device. Proper mounting assures optimal performance highest reliability. Sirenza applications note AN-054 Detailed Installation Instructions Power Modules.
Description LDMOS gate bias. VGSTH VDC. Notes
Simplified Device Schematic
+28V
Note Internal decoupling included bias leads. additional bypass elements required, however some applications require energy storage leads accommodate modulated signals. Note Gate voltage must applied leads simultaneously with after application drain voltage prevent potentially destructive oscillations. Bias voltages should never applied module unless properly terminated both input output. Note required corresponding specific will vary from module module differ between VGS1 VGS2 same module much ±0.10 volts normal die-to-die variation threshold voltage. LDMOS transistors. Note threshold voltage (VGSTH) LDMOS transistors varies with device temperature. External temperature compensation required. Sirenza application notes AN-067 LDMOS Bias Temperature Compensation. Note This module designed have it's leads hand soldered adjacent PCB. maximum soldering iron temperature should exceed 700° soldering iron should direct contact with lead longer than seconds. Refer note AN054 (www.sirenza.com) further installation instructions. http://www.sirenza.com EDS-103478
Balun
Balun
+28V
Absolute Maximum Ratings
Parameters Drain Voltage (VDD) Input Power Load Impedance Continuous Operation Without Damage Control (Gate) Voltage, Output Device Channel Temperature Operating Temperature Range Storage Temperature Range Value +200 +100 Unit VSWR
Operation this device beyond these limits cause permanent damage. reliable continuous operation typical setup values specified table page one. Caution: Sensitive
Appropriate precaution handling, packaging testing devices must observed.
Technology Court Broomfield, 80021
Phone: (800) SMI-MMIC
SDM-09120 925-960 120W Power Module
Quality Specifications Parameter Rating MTTF Human Body Model 85oC Leadframe, 200oC Channel Thermal Resistance (Junction-to-Case) Unit Hours Typical 2000
Typical Performance Curves
Tone Gain, Efficiency, Linearity Frequency Vdd=28V, Idq=1.2A, Pout=120W PEP, Delta Gain (dB), Efficiency Frequency (MHz) IMD(dBc), (dB)
Gain (dB), Efficiency
Tone Gain, Efficiency, Linearity Pout Vdd=28V, Idq=1.2A, Freq=942 MHz, Delta
(dBc)
Gain
Efficiency
Gain
Pout PEP)
Efficiency
Gain, Efficiency, Frequency Vdd=28V, Idq=1.2A, Pout=120W
Gain (dB), Efficiency
Gain, Efficiency Pout Vdd=28V, Idq=1.2A, Freq=942
Input Return Loss (dB)
Gain Efficiency Pout PEP) Efficiency
Gain (dB)
Gain Efficiency
1000
Frequency (MHz)
Technology Court Broomfield, 80021
Phone: (800) SMI-MMIC
http://www.sirenza.com EDS-103478
SDM-09120 925-960 120W Power Module
Typical Performance Curves (cont'd)
Gain, Efficiency, Supply Voltage Pout=120W, Idq=1.2A, Freq=942
Tone Gain, Efficiency, IRL, Supply Voltage Pout=120W PEP, Idq=1.2A, Freq=942 MHz, Delta
Gain (dB), Efficiency
Input Return Loss (dB)
Gain Efficiency
(Volts)
(Volts)
16.5
Gain Pout various Vds=28V, Freq=942
Pout various Vds=28V, Freq=942 MHz, Delta Idq=0.8A Idq=1.0A
Idq=1.6A Idq=1.4A Gain (dB)
Gain (dB)
Idq=1.2A
15.5 Idq=1.2A Idq=1.0A Idq=0.8A 14.5
Idq= 1.4A Idq=1.6A
Pout
Pout PEP)
Evaluation test fixture information available Sirenza Website, referred SDM-EVAL
Note:
Technology Court Broomfield, 80021
Phone: (800) SMI-MMIC
http://www.sirenza.com EDS-103478
Input Return Loss (dB), (dBc).
Gain (dB), Efficiency
Gain
Efficiency
SDM-09120 925-960 120W Power Module
Package Outline Drawing
.140 .125
3.56 3.18 (5X)
2.00 [50.8] 1.297 [32.94]
.140 .125
3.18 3.56 (5X)
LABEL LOCATION
(2X)
.055 [1.40]
(6X) 2.00 [50.8]
.100 [2.54]
LOGO MODULE NUMBER CODE NUMBER
1.274 [32.36] 1.52 1.49 37.85 38.61 .907 [23.04] .637 [16.18]
.367 [9.32]
.044 [1.12]
(2X) 1.800 [45.72]
.270 [6.86]
.540 [13.72]
.810 [20.57]
1.080 [27.43]
LEAD IDENTIFICATION
Lead
BASE PLATE
[2.9]
.703 [17.86]
.125 [3.18] (2X)
[5.3]
Function
VGS1 Ground Input Ground Ground Output Ground Ground
.005 [.13] [9.1]
.089 .076
1.93 2.26
.062 [1.57]
INTERPRET DRAWING ANSI Y14.5. MEASURE FROM BOTTOM LEADS. DIMENSIONS INCHES[MM]. LEAD IDENTIFICATION REFERENCE ONLY. ORIENTATION LABEL SHOWN.
MODULE WEIGHT 41gm NOMINAL
Refer Application note AN054, "Detailed Installation Instructions Power Modules" detailed mounting information.
Technology Court Broomfield, 80021
Phone: (800) SMI-MMIC
http://www.sirenza.com EDS-103478

SDM-09120 925-960 Class 120W Power Amplifier Module Product

Top Searches for this datasheet

Other recent searches