Bluetooth Antenna Design National Semiconductor Application Note

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

Bluetooth Antenna Design National Semiconductor Application Note

Datasheet Thumbnail

Top Searches for this datasheet

Bluetooth Antenna Design
Bluetooth Antenna Design
National Semiconductor Application Note April 2005
This application note intended designers using LMX5251 LMX5252 Bluetooth® radio chips LMX9820A LMX9830 Bluetooth modules. Antenna design various applications described along with theory, matching circuit description, suppliers examples. structure that resonant 2.45 with bandwidth more than efficiency >50% considered Bluetooth antenna. Therefore, countless variety antennas used, they application-specific. Some common types are: Wire Monopole-This consists simple wire soldered from which against ground plane. trimmed resonant 2.45 provides good performance high efficiency. disadvantage this antenna that profile because projects above PCB. PIFA-The Printed Inverted Antenna like monopole printed PCB, ground point feed point along main resonant structure. Helix-Similar wire monopole, except that coiled around central core (usually air) making physical dimensions smaller. provides excellent performance, projects above PCB. Ceramic-Surface mount dielectric antennas smallest types antennas available, because they printed high-dk ceramic slab, which makes electric field concentrated allowing antenna made small while keeping high resonant frequency. This application note only describes PIFA ceramic antennas because they most common, low-profile, smallest, inexpensive types available.
Theory
Printed surface-mount antennas have certain common properties. Area around beneath radiating element must kept copper-free. ground plane must placed side radiating element. Bandwidth >100 with VSWR <2.5 efficiency >60%. antenna will detune object placed close near field). This effect pulling frequency, which must retuned 2.45 GHz. oscillating constantly accelerating charge critical producing propagating waves. static non-accelerating charge will result non-propagating electric field. this only condition radiation. example, consider printed element microstrip, shown Figure
Quarter Wave
Feed Fringing field around Microstrip Substrate
Ground
Figure Fringing Field With Full Ground Plane fringing field around microstrip ground plane directly underneath substrate will confined small area. network analyzer connected feed point, would indicate high VSWR narrow bandwidth. This means very little radiation being emitted from microstrip element.
Bluetooth registered trademark Bluetooth SIG, Inc. used under license National Semiconductor.
©2005 National Semiconductor Corporation
increase radiation emission achieve greater bandwidth, ground plane must moved away from microstrip element which makes fringing field cover more distance, shown Figure should noted that ground plane moved far, then fringing field stops altogether, there radiation. Therefore, position size ground plane vital design good radiator.
radiation pattern from such antennas which physical size much smaller then wavelength almost symmetrical directions, shown Figure pattern controlled only when similar greater than
Quarter Wave
Azumith
Feed Radiation
Figure Fringing Field With Partial Ground Plane antenna could imagined impedance transformer, transforming impedance microstrip line (50) that free space (377), which allows power transferred from guided wave free-space wave.
Elevation
Figure Antenna Radiation Pattern Input return loss when viewed network analyzer looks like that shown Figure with full band covered with VSWR This gives very good matching into antenna, however real conditions when antenna detuned handling placement components close VSWR typical.
VSWR Freq. (GHz)
Figure Return Loss
www.national.com
Layout
PIFA placed edge motherboard PCB, shown Figure area around corner kept PIFA ANTENNA copper-free, components such shielding typical length 2.45-GHz resonant printed antenna that come close PIFA pull frequency. This depending thickness sub- retuned milling radiating element. strate dielectric constant. Copper clearance required LMX5251/LMX5252 surrounding components around radiating element which from point need shielding unless they very close along shown Figure position feed radiating element. used control input impedance into antenna. ground plane required side antenna approximately wide. were smaller, will start reduce bandwidth input. Good design practice have three-element matching network going Motherboard into feed, give some additional tuning ability PIFA required. obtain exact dimensions design, input impedance bandwidth would have simulated over frequency band using antenna simulation package. Alternatively antenna manufacturer Radio Circuit contacted that capability make such design.
Approx.
Copper-Free Area
Optional Shield
Antenna Ground Point
Feed Point Controls Input Impedance
Figure PIFA Antenna Placement
Copper Ground Plane
Matching
Figure Printed Inverted-F Antenna (PIFA)
www.national.com
CERAMIC DIELECTRIC ANTENNA
ceramic dielectric antenna smaller than PIFA other antenna because active element wound around high-dk ceramic slab, which concentrates electric field. with PIFA, copper-cleared area ground plane required, shown Figure smaller ground plane used, expense bandwidth efficiency.
Copper-Free Area
land pattern required mounting shown Figure
Copper-Free Area
Antenna
Ceramic Dielectric Antenna
Ground Through Hole
Microstrip Line
Figure Typical Chip Footprint ceramic dielectric antenna behaves similarly PIFA, that detuned, symmetrical radiation pattern, efficiency approximately 70%.
EXAMPLES 2.4-GHZ PIFA ANTENNAS
LMX5251
Copper
Ground Area Maximum Dimension Antenna Element Figure LMX5251 PIFA Antenna
Figure Ceramic Dielectric Antenna Placement example antenna from Mitsubishi with details ceramic element dimensions shown Figure
13.5
LMX5252
0.25
1403-244ST thickness
Unit: tol: ±0.2mm
Figure Typical Chip Dimensions
Maximum Dimension Antenna Element Ground Plane
Figure LMX5252 PIFA Antenna
www.national.com
LMX9820/A ANTENNAS
LMX9820 LMX9820A packaged shielded LTCC modules, approximately size. design antenna very similar that LMX5251/LMX5252, shielding makes differences. First, metal shield protects components module from electric field antenna, possible place LMX9820A much closer antenna element. Second, shielding also acts ground plane, less unpopulated ground area required around radiating element. example using ceramic dielectric antenna shown Figure module placed close radiating element. electric field from antenna couples surface shielded enclosure producing propagating radiation. shield well-grounded, there will adverse effects components inside.
Copper-Free Area
Figure LMX9830 Antenna
Antenna
Module
Copper Ground Plane
Figure LMX9820A Antenna
LMX9830 Antenna
LMX9830 smaller than 9820/A, approximately 9mm, however unshielded within plastic package there some important changes that need taken into account. cannot placed close antenna active element, else E-field give rise unwanted coupling effects, also E-field from antenna element will couple though main body module ground plane underneath. ground plane under module therefore important.
www.national.com
Matching
Purchased antennas, such surface-mount ceramic dielectric antennas, will matched input impedance with return loss <-7dB over bandwidth, centered 2.45 GHz. However, this only measured manufacturers test board, free space. Taking this antenna putting application PCB, which ground-plane layout different there detuning components such filters placed nearby, will pull resonant frequency antenna away from 2.45 GHz. antenna therefore needs matching correct frequency. This achieved means three-element network, placed input antenna. Usually capacitor pair inductor, inductor pair capacitor, will give sufficient tuning ability. There three steps matching: network analyzer must calibrated accurately with electrical delay removed. impedance measurement from 2.300 2.600 return loss Smith-Chart plot. Matching placing capacitors and/or inductors onto impedance changed.
NETWORK ANALYZER CALIBRATION
network analyzer should calibrated S11, oneport only measurements using open, short, load standard provided. flat line should obtained when standards removed shown Figure
Frequency: 2.300 2.600
Mk1: 2.50 GHz: 0.02
Figure Return Loss, Connection
www.national.com
Before soldering semi-rigid cable PCB, connected network analyzer cable, electrical delay adjusted with semi-rigid cable shorted. short cable attachment (less than cm), otherwise electrical delay will long. Electrical delay adjusted until measuring perfect short Smith Chart shown Figure
MEASUREMENT
Attach semi-rigid cable ground point close cable. When measuring input impedance antenna, important have setup wooden non-detuning surface keep your hands away from setup, otherwise measurement will incorrect. example typical return loss measurement shown Figure
1000
Perfect Short
1000
Frequency: 2.300 2.600 Mk1: 2.450 GHz: -3.30 Mk2: 2.510 GHz: -12.6
Figure Return Loss, Antenna Connected this example, resonant frequency antenna high. desired frequency, return loss only -3.3
Figure Smith Chart, Perfect Short
1000
1000
Figure Smith Chart, Antenna Connected
www.national.com
TUNING IMPEDANCE
After taking accurate measurement input impedance, tweaked using matching components three-element network. Marker impedance transformed shown Figure
PI-NETWORK MATCHING
popular type matching network PI-network, consisting shunt components with series component middle. This provides flexibility retuning detuned antenna. Even though only components normally used matching load source, allows putting shunt component either before after series component. example, consider data point Smith Chart: (10.2 j30.1) shown Figure
Shunt move constant resistance circle.
1000
50.0
25.0
1000 1000 Series move around constant conductance circle.
100.0
10.2 j30.1 20.0 10.0
500.0
0.08 50.0 100.0 200.0
500.0
Figure Impedance Transformation Starting from impedance point that needs matched (point 1.8-nH series inductor move from point shunt inductor will transform impedance point center chart, which normalized impedance point. matching network shown Figure
0.04
25.0 0.01
0.004
10.0
0.02
Source
Figure Single Frequency Data Point
Antenna
Figure Impedance Matching Network This only theoretical matching circuit. reality, inductors have parasitic resistance capacitance, impedance will transformed cleanly shown Smith Chart. Also, exact values shown above available standard kit. Some trial error required exact match required.
www.national.com
There methods matching load. first technique move around constant resistance circle from position adding series capacitance then from around constant conductance circle adding shunt capacitance, shown Figure
50.0
matching networks methods shown Figure
25.0
100.0
10.0
20.0
500.0
Figure Possible Matching Networks
0.08 50.0 100.0 200.0 500.0
allow both types matching, PI-pad must used with redundant bridged using zero- link. However, have only matched single-point frequency case real passive device such antenna, entire Bluetooth band matched closely possible least three frequency points have matched, shown Figure
50.0
0.04
25.0 0.01
0.004
10.0
0.02
25.0
100.0
Figure After Resistance-Conductance Tuning second technique move around conductance circle then resistance circle adding shunt series capacitance respectively, shown Figure
50.0
500.0 0.08 2.400 100.0 200.0 10.0 2.483 20.0
2.445
500.0
25.0
100.0
10.0
20.0
50.0
25.0 0.01
500.0
0.04 0.004 10.0
0.08 50.0 100.0 200.0 500.0
0.02
Figure Broadband Match difficulty with making broadband match frequency point that other will even further out! example, 2.483 brought closer adding shunt capacitor, 2.400 point will move around conductance circle creating even larger mismatch lower frequencies. compromise must found that will suit entire band. This normally involves using simulation software such HP-ADS (advanced design systems). this possible, then manual tweaking needed concentrating center frequency point.
0.04
25.0 0.01
0.004
10.0
0.02
Figure After Conductance-Resistance Tuning
www.national.com
First, input impedance detuned antenna measured using network analyzer saved S-parameters block, i.e. frequency points impedance points across Bluetooth band. This then entered into along with network, shown Figure
MATCHING NON-50 ACTIVE SOURCE/LOAD IMPEDANCE
source load impedances both non-50, then they matched much same impedance shown Figure
50.0
25.0
100.0
20.0 10.0 j10.2 j34.9
500.0
Shunt Series 100.0 200.0
500.0
Figure Network make model more realistic, more effective real components with added parasitics rather than just pure inductance capacitance. models components with parasitics shown Figure
0.08 50.0
0.04
25.0 0.01
Parasitic
0.004
10.0
0.02
Parasitic
Figure Matching Non-50 Impedance this example load source j35. series capacitance shunt inductance required transform load impedance that source. Because these non-50, they anywhere Smith Chart must measured using vector network analyzer (VNA) determine their exact value. Measuring input impedance receiver passive antenna simple. calibrated will display value screen. However, when measuring output impedance power amplifier transmitter, this technique cannot used because power being transmitted will completely disrupt reading. technique conjugate matching using variable load must used.
Parasitic
Parasitic
Figure Component Models Data parasitic values obtained from component manufacturer. Starting with best possible values used match 2.445 GHz, model entered into ADS, optimization procedure reduce much possible iterative steps from 2.400 2.483 GHz. simulation finely tweaks PI-pad component values measures S11. lower, then components tweaked again same direction until best optimized solution found. same procedure used larger matching networks even active networks, which yield better results. However larger circuits will have higher insertion loss parasitic resistance present within components.
www.national.com
Figure variable load attenuator provide desired load impedance Therefore, influence output power which measured using power meter attached coupled port directional coupler. When perfect conjugate match applied output power measured power meter will maximum, which signifies best power transfer conditions.
Through transfer coefficient SQRT(1-[S11]^2) 0.98 Power transferred [S21]^2 0.96 Meaning that power received antenna will transferred receiver even with this missmatch. achieve higher power transfer efficiency than this non-50 must used described above.
Power Meter
20dB Coupling Variable Load Directional Coupler Variable Attenuator
Figure Setup Determining Output Impedance When best power transfer achieved, variable load attenuator fixed that their impedance cannot changed. detached from directional coupler attached input directional coupler measure input impedance this point. measured impedance conjugate output impedance impedance measured then output impedance will definition. Definition: term conjugate match means that direction from junction impedance then opposite direction impedance will condition maximum power absorption load, which impedance seen looking toward load point transmission line complex conjugate that seen looking toward source. 4.5.1 LMX5252 Impedance Match case LMX5252 where impedances different slightly options available antenna designer, either assume point simpler design, which case small missmatch will result causing small degradation Tx/Rx power. make matching network described above between non-50 points. first instance where input/output impedance assumed power loss that will results follows; Worse case input impedance VSWR this point Reflection coefficient Return Loss 10LOG(S11)
www.national.com
Antenna Vendors
Table lists vendors off-the-shelf antenna products custom designs. Table Antenna Vendors Vendor gigaAnt Products Contact Information
Small ceramic chips larger surface-mount antennas gigaAnt suitable mobile phones, headsets laptops, printers, Ideon Science Technology Park etc. S-223 Lund Sweden example, 3030A5839-01 Leftside, 3030A5887-01 Rightside. Phone:+46 Web: www.gigaant.com E-mail: info@gigaant.com
Mitsubishi Materials
Small ceramic chips surface-mount. Suitable mobile Mitsubishi Materials Corporation applications Advanced Products Strategic Company Sales Group, Electronic Components 1-297, Kitabukuro-cho, Omiya-ku Saitama-city, Saitama, 330-8508 Japan Phone: 5991 Fax: 5562 Web: www.mmc.co.jp E-mail: devsales@mmc.co.jp
Tyco Electronics
Large high-gain printed antennas applications such Tyco Antenna Products/Rangestar access points. Metro Park Small ceramic chips surface-mount. Suitable mobile Rochester, 14623 applications Phone: (585) 272-3103 Fax: (585) 272-3110 Web: www.rangestar.com
Centurion
surface-mount antennas various applications.
Centurion Wireless Technologies 82846 Lincoln, 68501 Phone: (402) 467-4491 Fax: (402) 467-4528 Web: www.centurion.com E-mail: sales@centurion.com
Murata
surface-mount antennas example, series ANCM12G45SAA072 series ANCW12G45SAA110TT1.
Murata International Sales Dept. 3-29-12 Shibuya, Shibuya-ku Tokyo 150-0002 Japan Phone: 5469 6123 Fax: 5469 6155 Web: www.murata.com E-mail: intl@murata.co.jp
www.national.com
Comparison Summary
Table compares features different antenna types. Table Antenna Comparison Antenna Type Stub helix monopole Performance Profile Cost Physical Size antenna approximately long, projects. Does need ground plane function.
Good bandwidth efficien- High: Projects from side High does require matching network.
Surface-mount Reasonable performance Low: machine Medium Element approxiceramic chip g/4. Small bandwidth mounted during assembly, mately long, needs duced efficiency. become more than thick ground area clearance detuned during handling around active region. Printed inverted-F other printed types Reasonable performance Lowest: Printed g/4. Small bandwidth reduced efficiency. become detuned during handling Element approximately long, needs ground area clearance around active region.
Points Consideration
Many types antennas available. Antenna type chosen application. Larger antennas generally have better performance than smaller ones. Ground plane always required with printed ceramic antennas. Cannot metal objects such crystals close antenna without causing detuning. case phone other device will also detune antenna, some tuning adjustment ability needed. Matching elements have parasitic values that affect their quality; this possible simulate using simple simulation software. Some trial error therefore required when performing match sophisticated simulation tool must used. LMX9820A shielding will ground plane antenna placed correctly. LMX5251/LMX5252 radio chip must shielded from strong electric field only placed close radiating element. Shielding will improve performance always required.
www.national.com
Examples Antennas Used With LMX5251/LMX5252
Figure Ceramic Chip Antenna Intelligent Remote Access Lock
Figure Ceramic Chip Antenna Industrial Remote Control with External
Figure Ceramic Chip Antenna Distance Meter
Figure Printed Antenna-Monopole Yagi-Array Off-Board Navigation Using
www.national.com
Figure External Antenna-Helix Monopole Automotive Integrated Hands-Free
Figure Surface-Mount Chip Antenna (Phycomp AN-2700 Murata ANCM12G) Automotive Hands-Free
13.5
0.25
1403-244ST thickness
Unit: tol: ±0.2mm
Figure Surface-Mount Chip Antenna (Mitsubishi Materials 1403) Electronic Whiteboard
Figure Printed PIFA Antenna Automotive Hands-Free
www.national.com
Bluetooth Antenna Design
Popular Antenna Types
Ceramic chip antennas (Mitsubishi, gigaAnt) most popular types being used Bluetooth products. These cost about cents/unit.
Copper-Free Area Antenna
Ground Through Hole
Microstrip Line
Figure Mitsubishi AHD1403 Surface-Mount Antenna second most popular type PIFA. These have lowest cost because they consist trace, larger more design-intensive. Figure gigaAnt Rufa Antenna
National does assume responsibility circuitry described, circuit patent licenses implied National reserves right time without notice change said circuitry specifications. most current product information visit www.national.com.
LIFE SUPPORT POLICY NATIONAL'S PRODUCTS AUTHORIZED CRITICAL COMPONENTS LIFE SUPPORT DEVICES SYSTEMS WITHOUT EXPRESS WRITTEN APPROVAL PRESIDENT GENERAL COUNSEL NATIONAL SEMICONDUCTOR CORPORATION. used herein:
Life support devices systems devices systems which, intended surgical implant into body, support sustain life, whose failure perform, when properly used accordance with instructions provided labeling, reasonably expected result significant injury user. critical component component life support device system whose failure perform reasonably expected cause failure life support device system, affect safety effectiveness.
BANNED SUBSTANCE COMPLIANCE
National Semiconductor certifies that products packing materials meet provisions Customer Products Stewardship Specification (CSP-9-111C2) Banned Substances Materials Interest Specification (CSP-9-111S2) contain "Banned Substances" defined CSP-9-111S2.
National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center
Fax: 180-530 Email: europe.support@nsc.com Deutsch Tel: 9508 6208 English Tel: 2171 Francais Tel: 8790
National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com
National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560

Bluetooth Antenna Design National Semiconductor Application Note

Top Searches for this datasheet

Other recent searches