Ethernet: BASE-T IEEE 802.3 BASE-TX IEEE 802.3u Wiring: UTP, category

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

Ethernet: BASE-T IEEE 802.3 BASE-TX IEEE 802.3u Wiring: UTP, category

Datasheet Thumbnail

Top Searches for this datasheet

Common technical specification ADAM-6000
Ethernet: BASE-T IEEE 802.3 BASE-TX IEEE 802.3u Wiring: UTP, category greater Connection: RJ45 modular jack Comm. Protocol: Modbus/TCP TCP/IP Data Transfer Rate: Mbps Unregulated 30VDC Protection: Over-voltage power reversal Ethernet Communication: 1500 Module: 3000 Status Indicator: Power, CPU, Communication (Link, Collide, 10/100 Mbps, Case: with captive mounting hardware Plug-in Screw Terminal Block: Accepts Operating Temperature: Storage Temperature: (-13 Humidity: 95%, non-condensing Atmosphere: corrosive gases NOTE: Equipment will operate below humidity. However, static electricity problems occur much more frequently lower humidity levels. Make sure take adequate precautions when touch equipment. Consider using ground straps, anti-static floor coverings, etc. equipment humidity environments.
Dimensions
following diagrams show dimensions ADAM-6000 module millimeters.
Figure 1-2: ADAM-6000 Module Dimension
Analog Input Module
Analog input modules converter convert sensor voltage, current, thermocouple signals into digital data. digital data then translated into engineering units. When prompted host computer, data sent through standard 10/100 based-T Ethernet interface. Users would able read current status pre-built page software package supported Modbus/TCP protocol. analog input modules protect your equipment from ground loops power surges providing opto-isolation input trans-former based isolation 3,000
ADAM-6017 8-channel Analog Input with 2/DO Module
ADAM-6017 16-bit, 8-channel analog differential input module that provides programmable input ranges channels. accepts millivoltage inputs (±100mV, ±500mV), voltage inputs (±1V, ±10V) current input (±20 4~20 provides data host computer engineering units (mV, mA). order satisfy plant needs module, ADAM-6017 designed with analog inputs digital outputs. Each analog channel allowed configure individual range variety applications.
ADAM-6017
Figure 4-1: ADAM-6017 8-channel Analog Input w/2DO Module
ADAM-6017 Specification
Analog Input:
Effective resolution: 16-bit Channels: differential lnput type: lnput range: ±150 ±500 0-20 4-20 Isolation voltage: 3000 Fault overvoltage protection: Withstands overvoltage Sampling rate: samples/sec. Input impedance: Bandwidth: 13.1 15.72 Accuracy: ±0.1% better Zero drift: µV/° Span drift: ppm/° 50/60 min.
Digital Output:
Channel: Open Collector max. load Optical Isolation: 5000VRMS
Built-in Watchdog Timer Power
Power requirements: Unregulated Power consumption:
Digital Module
ADAM-6050 18-channel Digital Module
ADAM-6050 high-density module built-in 10/100 based-T interface seamless Ethernet connectivity. provides digital input digital output channels with 5000VRMS Isolating protection. Digital Input channels support input latch function important signal handling. Mean while, these channels allow used counter. Opposite intelligent functions, Digital Output channels also support pulse output function.
ADAM-6050
Figure 4-6: ADAM-6050 18-channel Digital Module
ADAM-6050 Specification
Analog Input:
Channel: type: Digital Input: Contact: Logic level Close Logic level Open (Logic level status inversed Utility) Digital Output: Open Collector max. load Optical Isolation: 5000VRMS Power Consumption: (Typical)
ADAM-6051 16-channel Digital w/Counter Module
ADAM-6051 high-density module built-in 10/100 based-T interface seamless Ethernet connectivity. provides digital input, digital output, counter KHz) channels with 5000VRMS Isolating protection. Digital Input channels support input latch function important signal handling. Mean while, these channels allow used counter. Opposite intelligent functions, Digital Output channels also support pulse output function.
ADAM-6051
Figure 4-11: ADAM-6051 16-channel Digital w/Counter Module
ADAM-6051 Specification
Channel: type: 12DI 2Counter Digital Input: Contact: Logic level Close Logic level Open (Logic level status inversed Utility) Digital Output: Open Collector max. load Optical Isolation: 5000VRMS Counter: Maximum Count: 4,294,967,285(32 bit) Input frequency: 1000 max. (frequency mode) 5000 max. (counter mode) Isolation voltage: 2500 VRMS Mode: Counter (Up/Down, Bi-direction), Frequency Power Consumption: (Typical)
ADAM-6060 6-channel Relay Output with Module
ADAM-6060 high-density module built-in 10/100 based-T interface seamless Ethernet connectivity. Bonding with Ethernet port page, ADAM-6060 offers relay (form output digital input channels. supports contact rating 120V 0.5A, Digital Input channels support input latch function important signal handling. Mean while, these channels allow used counter. Opposite intelligent functions, Digital Output channels also support pulse output function.
ADAM-6060
Figure 4-16: ADAM-6060 6-channel Relay Output w/DI Module
ADAM-6060 Specification
Channel: type: Relay Relay Output (Form Contact rating: Breakdown voltage: (50/60 Relay time: msec; Relay time: msec. Total switching time: msec. Insulation resistance: 1000 minimum Digital Input: Contact: Logic level Close Logic level Open (Logic level status inversed Utility) Optical Isolation: 5000VRMS Power Consumption: (Typical)

Ethernet: BASE-T IEEE 802.3 BASE-TX IEEE 802.3u Wiring: UTP, category

Top Searches for this datasheet

Other recent searches