basic switch modules cycle mechanical life switch. increased actu

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

basic switch modules cycle mechanical life switch. increased actu

Datasheet Thumbnail

Top Searches for this datasheet

Advanced sealing techniques state plastic materials used ensure maximum electrical mechanical reliability, even most demanding environments. Multimec switches available either through-hole mounting surface mount. Four basic switch modules provide basis assembly
basic switch modules
cycle mechanical life switch. increased actuation force available option. Multimec switches sealed IP-67M specifications available with either silver optional gold contacts standard high temperature models.
wide variety options produce both illuminated non-illuminated switches. versatility Multimec switches offers designer great flexibility creating unique front panel designs. actuator travel combined with 2.5N actuation force, (250g.), provides strong audible tactile feel throughout million
Through-hole Version 1A/1B w/LED 1C/1H 1D/1K/1P/1S w/LED 1E/1F/1Q/1R/1S w/LED 1K1116
10.4
Min. 10.16 12.5
Min. 10.16 12.5
Min. 10.16 12.5
Min. 10.16 12.5
Min. 10.16 12.5
Min. 10.16 12.5
Min. 10.16 12.5
-15.0
2.54 2.54 2.54
2.54 2.54 2.54
12.7±0.3
12.7±0.3
2.54 2.54 2.54
Standard Versions 3ATL6 3ATH9 3ATL620/40/80 3CTL6/3CTL9 3CTH9 3ETL9-H* 3ETH9-H* 3FTL6 3FTH9 3FTL620/40/80 3FTL622/44/88
available standard heights: 08.0, 09.5, 10.4, 12.0, 15.0 Other heights between 08.0 15.0 available upon request
Specials: Gold contacts, quiet version actuation force other than 2.5N Surface Mount Versions
10.4
Right Angle Versions
8.68 13.9 17.7
Max. 0.05
Max. 0.05
Max. 0.05
Max. 0.05
7.62
4.85
10.4
10.4
-15.0
3ASH9 1A/1B
3CSH9
3ESH9
3FSH9 1D/1P/1S
3CTL6RAS
3FTL6RAS 1D/1K/1P/1S
Operating Force Typical example
Force
Circuit diagram DIMENSIONS (mm) Unless otherwise specified, tolerances ±0.2
Travel (mm)
Industriparken P.O. DK-2750 Ballerup Denmark Tel.: Fax: Web: http://www.mec.dk E-mail: danmec@vip.cybercity.dk
7.62
MULTIMEC Through-hole
10.16
Recommended layout
MULTIMEC Surface-mount solder pad.
12.5
MULTIMEC Right Angle Version
7.62 5.08
7.62
2.54
2.54
Optional
MULTIMEC basic switch spacing
Through-hole Surface-mount
Spacing examples
multimec® 1B/C 2A/B multimec® 1B/C 2A/B
7.62
12.2
7.62
Min. 10.16
Min. 10.16
12.2
Min. 10.16 12.5 10.16 Min. 10.16 12.5
1.24
15.24
5.08
10.16
Min. 12.70
Min. 15.24
multimec® 1A/H
Recommended switch/cap spacing
Switch Spacing dimension
12,2
10,16
2,54
10,16
multimec
Panel cut-out
12.2
10.16
15.24
10.16
X=13
series
Recommended min. switch spacing 12.7 10.16 15.24 15.24 12.7 12.7 15.24 15.24 25.4 10.16 15.24 10.16 12.7 10.16
Nominal dimension 12.6 10.1 15.1 15.1 14.3 14.3 25.0 10.1 12.5
Recommended min. panel cut-out 13.0 10.5 15.5 15.5 10.0 14.7 14.7 25.7 10.5 13.0, max.
1A/1H 1B/1C+2A/2B 1D/1E/1F 1P/1Q/1R
dimension with Surface mount version min. 15.24. Depending manufacturing technology necessary either reduce dimension, increase spacing. applications total assemble tolerance must analysed user (board tolerance, front panel, assembly accuracy), secure enough room free switch movement final product. specifications this page considered only. cannot assume responsiblity final assembly. Industriparken P.O. DK-2750 Ballerup Denmark Tel.: Fax: Web: http://www.mec.dk E-mail: danmec@vip.cybercity.dk
1D/1E/1F
Technical Data: through-hole 50mA/24VDC single pole/momentary 10.000.000 operations life time IP67 sealing temperature range: temp: -40/+65°C high temp: -40/+160°C
Dimensions (through-hole)
Dimensions (w/LED)
Dimensions (SMD)
14.9
18.9
14.9
18.9
14.9
Min. 10.16 12.5
Min. 10.16 12.5
10.16
10.1
10.1
layout
10.1
layout (top view)
10.16
layout
12.5
7.62
10.1
7.62
7.62
2.54
10.1
2.54
10.1
2.54
10.1
2.54
10.1
ORDER Switch Mounting through-hole surface mount temp. high temp.
blue green grey yellow white black
Standard versions: 3FTL6 3FTH9 3FSH9
Switch
Mounting through-hole temp. high temp. green yellow
blue green grey yellow white black Lens transparent green yellow
Standard versions: 3FTL620 3FTL640 3FTL680
Ordering example: FTL620 1E032 Industriparken P.O. DK-2750 Ballerup Denmark Tel.: Fax: Web: http://www.mec.dk E-mail: danmec@vip.cybercity.dk
Technical Data: through-hole 50mA/24VDC single pole/momentary 10.000.000 operations life time IP67 sealing temperature range: temp: -40/+65°C high temp: -40/+160°C
Dimensions (through-hole)
Dimensions (w/LED)
Dimensions (SMD)
Dimensions (Bezel) (Optional)
19.1
11.6
11.6
19.1
19.1
11.6
Min. 10.16 12.5
16.4
Min. 10.16 12.5
layout
10.16
layout (top view)
10.16
layout
14.6
12.5
14.3
7.62
7.62
7.62
14.3
14.3
2.54
2.54
2.54
14.3
14.3
2.54
14.3
17.75
ORDER
Switch Mounting through-hole surface mount temp. high temp.
blue green grey yellow white black
Bezel grey white black
Standard versions: 3FTL6 3FTH9 3FSH9
Switch
Mounting through-hole temp. high temp. green yellow
transparent
Bezel grey white black
Standard versions: 3FTL622 3FTL644 3FTL688 Ordering example: 3FTL680 1K1116 Industriparken P.O. DK-2750 Ballerup Denmark Tel.: Fax: Web: http://www.mec.dk E-mail: danmec@vip.cybercity.dk
17.75
14.6
1P/1Q/1R
Technical Data: through-hole 50mA/24VDC single pole/momentary 10.000.000 operations life time IP67 sealing temperature range: temp: -40/+65°C high temp: -40/+160°C
Dimensions (through-hole)
12.5
Dimensions (w/LED)
12,5
Dimensions (SMD)
12.5
15.7
Min. 10.16 12.5
2.54 2.54 2.54
Min. 10.16 12.5
10.16
10.1
layout
10.1
10.1
7.62
layout (top view)
10.16
layout
12.5
7.62
10.1
7.62
2.54
2.54
10.1
2.54
10.1
2.54
10.1
order Switch Mounting through-hole surface mount temp. high temp. blue green grey yellow white black
Standard versions: 3FTL6 3FTH9 3FSH9
Switch
Mounting through-hole temp. high temp. green yellow
blue grey black
Lens transparent
Standard versions: 3FTL620 3FTL640 3FTL680
Ordering example: FTL680 1Q091 Industriparken P.O. DK-2750 Ballerup Denmark Tel.: Fax: Web: http://www.mec.dk E-mail: danmec@vip.cybercity.dk
10.4
10.4 15.7
19.6
10.4 15.7 19.6
3F+1S
Technical Data: through-hole 50mA/24VDC single pole/momentary 10.000.000 operations life time IP67 sealing temperature range: temp: -40/+65°C high temp: -40/+160°C
Dimensions (through-hole)
Dimensions (w/LED)
Dimensions (SMD)
R12.5
H±0.2
7.5±0.2
R12.5
R12.5
7.5±0.2
H±0.2
10.16 12.5
7.6±0.5
10.16 12.5
2.54 2.54 2.54
7.6±0.5
layout
10.1
10.16
10.1
layout (top view)
10.16
10.1
layout
12.5
10.1
10.1
10.1
7.62
7.62
7.62
2.54
2.54
2.54
2.54
ORDER Switch Mounting through-hole surface mount temp. high temp. black Height 16.0 19.0 22.5 Extender black Height (Optional) Adds 10mm total height (stackable)
Standard versions: 3FTL6, 3FTH9, 3FSH9
Switch
Mounting through-hole temp. high temp. green yellow
transparent
Height 16.0 19.0 22.5
Standard versions: 3FTL620, 3FTL640, 3FTL680
Customised heights: available height from 12.0 22.5 available height from 22.0 32.5 Min. order qty. custom heights 2.000 pcs. start-up charge will apply. heights less than 12.0 please refer switch range. Ordering example: FTL640 1S11-19.0 Industriparken P.O. DK-2750 Ballerup Denmark Tel.: Fax: Web: http://www.mec.dk E-mail: danmec@vip.cybercity.dk
7.5±0.2 Total height 22.0 32.5 ±0.3
Electrical Specifications Contact resistance Insulation resistance Recommended load Contact bounce Mechanical Specifications Standard actuation force (switch) Max. actuation force without travel (switch) Life time (switch) Temperature Range Working temperature Storage temperature Soldering 68-2-20
technical specifications
High Temperature Versions Silver Gold
Temperature Versions Silver Gold typically >10M 0.5-50mA 24VDC <2mS typically 0.5mS 2.5N typ. 100N sec. >10.000.000 cycles Min. -40°C Max. +65°C Min. -40°C Max. +65°C Wave -max. 260°C max. Sec., please refer usage guidelines Soldering iron max. 350°C max. Sec. Flux tight. +40°C Days Min. -55°C Max. +65°C min. hrs. IP-67M Standard methods such freon, water soap Polycarbonate UL94V1 UL94V1 Silicone rubber Stainless steel 3µAG SNCU 2µNI 3µAG UL94V1 Max. +65°C
0-50mA 24VDC
0.5-50mA 24VDC
0-50mA 24VDC
Min. -40°C Max. +160°C Min. -40°C Max. +160°C Infrared, vapour phase, wave max. 260°C max. Sec. Soldering iron max. 350°C max. Sec. Flux tight.
Environmental Endurance IEC-68-2-3 Temperature Humidity Duration Temperature Cycling 68-2-14 Temperature limit Number cycles Exposure time each temperature Recovery time before measurements Sealing Cleaning Material Specifications Switches Housing Actuator Sealing spring Contact spring Terminals Material Specifications Caps Bezels Temperature Limit Specifications subject change without notice
UL94V1 UL94V1 Stainless steel 3µAG 3µAU SNCU 2µNI 3µAU Stainless steel 3µAG SNCU 2µNI 3µAG Stainless steel 3µAG 3µAU SNCU 2µNI 3µAU
multimec® LEDs
Part Nos. Colour Green, Yellow, Red) Absolute Maximum Ratings Power Current forward Forward peak current Voltage reverse Operating temperature Storage temperature Soldering temperature Electrical-Optical Characteristics Voltage forward Current reverse Wave length Spread Spread angle Luminous Intensity Orientation (Ta=25°C) (Ta=25°C) Typ. Max. degree Min. Typ.
20mA **Pulse width Duty cycle 1CXXX (for Switch) +100 +100 max. sec. 2BXXX
***IF 50mA ****Luminous Flux 3FXXX (for 1E-1F 1Q-1R) 60** 60** 60** +100 max. sec. 3FXXX (for
60** 60** 60** +100 max. sec.
+100 +100 max. sec. 2.4*** 3.8*** 100**** 160**** 2.4*** 3.8*** 100**** 160**** 2.4*** 3.8*** 100**** 160****
2.1* 2.1* 2.0* 2.8* 2.8* 2.8* longer anode, shorter cathode
Industriparken P.O. DK-2750 Ballerup Denmark Tel.: Fax: Web: http://www.mec.dk E-mail: danmec@vip.cybercity.dk
General Information
best results with Switches Usage Guidelines
These guidelines offered users switches ensure successful reliable switch operation. Temperature Both UNIMEC MULTIMEC switches produced standard high temperature materials. Please technical specifications details operating storage temperatures soldering guidelines make sure select switch best suited your application. When flow soldering, strongly recommend that temperature profile analysed compared with temperature rating switch. case doubt always select high temperature version 3XXH9. accessories both UNIMEC MULTIMEC switches made from plastic with maximum operating temperature 65°C. Care must taken overheat accessories during soldering process. soldering processes exposing switch high temperatures strongly recommended that accessories mounted after soldering. LED's have their temperature specifications. When fitted high temperature switch will determine max. operating temperature, i.e. 3FTH922 upper temperature limit 85°C 160°C! When infrared reflow soldering used, very important monitor surface temperature switch during pre-heat stage prevent excessive heat buildup overheating during soldering. Mounting switches mounted rows critical that recommendations regarding spacing followed. board thickness should 1.6mm terminal hole diameters should 0.9mm. UNIMEC MULTIMEC caps bezels easily snapped onto switch modules changed later time with exception UNIMEC 16.700 cap. Once this installed designed removed. cause damage switch board done with extreme care. 16.300 16.700 must removed from alternate action switch, make sure that switch actuator released, upper position before attempting remove cap. This will prevent possible damage internal latching pin. Care must taken when inserting switch assembly into board. press direct LED. This will force down into actuator cause switch contacts remain closed position. correct fault, must raised slightly centered actuator assure unrestricted movement actuator. Soldering Cleaning UNIMEC Most assembly field problems experienced users unsealed switches caused contamination contacts during soldering cleaning. Contact contamination recognized increase contact resistance possible intermittent operation switch, especially power applications. Care must taken submerge switch solder bath spray switch during cleaning. switch must protected times prevent contamination flux cleaning fluids. Soldering Cleaning MULTIMEC MULTIMEC switches fully sealed IP-67M specifications prevent solder flux aqueous solvent cleaning solutions from entering switch contaminating contacts. switches placed board with other components wave soldered. special handling MULTIMEC switches required, notice guidelines mentioned under "temperature".
Soldering Multimec
Through hole versions Hand soldering: 350°C max. this applies both temperature high temp. versions. Wave soldering: Heat built switch during pre-heating soldering must exceed maximum operating temperature switch. some reason, high pre-heating temperature required, strongly recommend using high temperature switches. cases peak temperature must exceed 260°C, soldering time max. Surface Mount versions methods Infrared, convection vapour phase upper limit 260°C/30 must observed. soldering temperature profile must have moderate temperature gradients T/t. General Temperature limitations temperature 65°C High temperature 160°C LED's 85/100°C Accessories 65°C recommend that accessories mounted after soldering, unless process allows heat exposure kept within limits 65°C. Combinations high temperature switches with LED's will limited temperature capability LED. Packaging UNIMEC MULTIMEC switches packed rigid tubes pieces each.
Assemble Examples
unimec 16300 16310 unimec 16270 16300 16324
multimec® 1A/H 2A/B
multimec® 1B/C 2A/B
Industriparken P.O. DK-2750 Ballerup Denmark Tel.: Fax: Web: http://www.mec.dk E-mail: danmec@vip.cybercity.dk

basic switch modules cycle mechanical life switch. increased actu

Top Searches for this datasheet

Other recent searches