DC/DC CONVERTERS VOLT INPUT HR150 SERIES WATT MODELS OU

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

DC/DC CONVERTERS VOLT INPUT HR150 SERIES WATT MODELS OU

Datasheet Thumbnail

Top Searches for this datasheet

-40°C +85°C operation input input Fully Isolated Optocoupler feedback Fixed frequency, typical single dual outputs typical triple outputs Transient protection models Inhibit function Indefinite short circuit protection efficiency Output trim single output models
DC/DC CONVERTERS VOLT INPUT
HR150 SERIES WATT
MODELS
OUTPUT SINGLE DUAL TRIPLE
Size (max.): HR151 HR152 models, case 2.125 1.125 0.495 inches (53.98 28.58 12.57 HR153 models, case 1.950 1.350 0.505 inches (49.53 34.29 12.83 section cases dimensions. Weight: HR151 HR152: grams typical. HR153: grams typical. Screening: Standard only. Section screening description.
DESCRIPTION
HR150 SeriesDC/DC converters have been designed give industrial applications same high reliability, small size, high performance that Interpoint provided military aerospace programs since 1969.
models typical triple output models. They achieve high isolation (500 megohm) through transformer forward power circuit opto-coupler feedback control loop. Series input ranges single triple output models dual output models. Outputs available ±12, ±15, +5/±12, +5/±15 VDC. converters typically provide greater than efficiency over entire input range from full load. Line regulation typically within load regulation within 0.2%. HR150 converters designed operate between -40°C +85°C case short circuit protected case temperature 85°C. combination high conversion efficiency heat dissipating metal enclosures minimizes heat sinking requirements. additional dissipation desired, heat conducting material (PCB, copper sheet, heat sink, etc.) brought into contact with unit's baseplate. inhibit function provided HR150 converters when inhibit input connected input common. open circuit voltage inhibit input (Vin (Vin 28). inhibit input must sink approximately during inhibit state. During inhibit, converter's output voltage drops less than volt input current typically
HIGH RELIABILITY
Each HR150 converter built perform reliably harshest environments. Assembled using thick-film hybrid technology, HR150 converters have more uniform thermal coefficients fewer connections than converters built surface mount techniques. HR150 converter parts same manufacturing procedures quality controls that apply converters designed commercial airliners, space shuttle, advanced fighter aircraft, other high reliability applications. steel cases hermetically sealed nitrogen environment guaranteed maximum leak rate less than 10-3 atm-cc/sec. devices 100% electrically tested.
SMALL SIZE PROFILE
HR150 Series manufacturing techniques provide extremely small size profile components. Each converter uses less than square inches board area. overall power density from watts cubic inch.
HIGH PERFORMANCE
HR150 Series converters high efficiency, noise, pulse width modulated, forward mode switching regulators with constant switching frequency typical single dual output
B4-43
HR150 SERIES WATT
ABSOLUTE MAXIMUM RATINGS
DC/DC CONVERTERS
INHIBIT
Inhibit Open Collector Logic (output disabled) Inhibit current typical Inhibited input current typical Referenced input common Logic high (output enabled) Open collector
TYPICAL CHARACTERISTICS
Output Voltage Temperature Coefficient ppm/°C, typical Input Output Capacitance typical Isolation megohm minimum Conversion Frequency Inhibit Voltage (unit enabled) HR15X-12XX models HR15X-28XX models Line Regulation 0.1% typical, 0.2% maximum Load Regulation 0.2% typical, 0.4% maximum
Input Voltage HR15X-12XX HR15X-28XX Output Power watts (HR151-2812 HR151-2815, watts) Lead Soldering Temperature sec) 300°C Storage Temperature Range (Case) -55°C +125°C
RECOMMENDED OPERATING CONDITIONS
Input Voltage Range continuous HR15X-12XX models continuous HR15X-28XX models V/50 transient HR15XX-28XX models Case Operating Temperature (Tc) -40°C +85°C full power -40°C +105°C absolute Derating Output Power/Current Linearly from 100% 85°C 105°C HR151 HR152 models Linearly from 100% 85°C 115°C HR153 models
Electrical Characteristics: 25°C models), 100% load, unless otherwise specified.
SINGLE OUTPUT MODELS, PARAMETER OUTPUT VOLTAGE OUTPUT CURRENT OUTPUT POWER OUTPUT RIPPLE INPUT VOLTAGE INPUT CURRENT INPUT RIPPLE CURRENT EFFICIENCY CONTINUOUS LOAD CONDITIONS HR151-1205 4.95 5.05 HR151-1212 11.88 12.12 1.25 14.85 HR151-1215 15.15 UNITS
SINGLE OUTPUT MODELS, PARAMETER OUTPUT VOLTAGE OUTPUT CURRENT OUTPUT POWER OUTPUT RIPPLE INPUT VOLTAGE INPUT CURRENT INPUT RIPPLE CURRENT EFFICIENCY CONTINUOUS TRANSIENT LOAD CONDITIONS
HR151-2805 4.95 5.05
HR151-2812 11.88 12.12 1.667
HR151-2815 15.15 1.333 UNITS
14.85
B4-44
DC/DC CONVERTERS
DUAL OUTPUTS PARAMETER OUTPUT VOLTAGE OUTPUT CURRENT OUTPUT POWER OUTPUT RIPPLE INPUT VOLTAGE INPUT CURRENT INPUT REFL. RIPPLE EFFICIENCY CONDITION HR152-2812 HR152-2815
HR150 SERIES WATT
Electrical Characteristics: 25°C models), 100% load, unless otherwise specified.
UNITS
±11.88 ±12.00 ±12.12 CONTINUOUS TRANSIENT LOAD ±625
±14.85 ±15.00 ±15.15 ±500
TRIPLE OUTPUTS PARAMETER OUTPUT VOLTAGE OUTPUT CURRENT OUTPUT POWER OUTPUT RIPPLE INPUT VOLTAGE INPUT CURRENT INPUT REFL. RIPPLE EFFICIENCY CONDITION FULL LOAD MAIN DUAL
HR153-1212
HR153-1215
HR153-2812
HR153-2815 UNITS
4.95 5.00 5.05 ±11.88 ±12.00 ±12.12 2000 ±208
4.95 5.00 5.05 4.95 5.00 5.05 4.95 5.00 5.05 ±14.85 ±15.00 ±15.15 ±11.88 ±12.00 ±12.12 ±14.85 ±15.00 ±15.15 2000 ±167 2000 ±208 2000 ±167
MAIN1 DUAL MAIN ±DUAL TOTAL MAIN DUAL CONTINUOUS TRANSIENT LOAD
Note Minimum load required full output capability auxiliary outputs. Minimum current reduced when dual outputs used reduced loads.
B4-45
HR150 SERIES WATT
DC/DC CONVERTERS
Single Output Positive Input Inhibit Trim Output Common Positive Output connection connection Case Ground connection Input Common Dual Output Positive Input Inhibit Positive Output Output Common Negative Output connection connection Case Ground connection Input Common Triple Output Positive Input Main (+5) Output Output Common Neg. Aux. Output Pos. Aux. Output connection Case Ground Inhibit connection Input Common Squared corner package indicate one.
package indicates
BOTTOM VIEW HR151 HR152
BOTTOM VIEW HR153
Section case dimensions. Section case dimensions.
FIGURE HR151 HR152
FIGURE HR153
OUTPUT ADJUSTMENT RESISTOR VALUES HR151-2805 Resistance Output Voltage Increase
390K 145K
MODEL NUMBERING
HR15 Base Model Number Outputs single, dual, triple) Input Voltage
Output Adjustment HR151 models (single output): output adjusted upward using output adjust (pin3). resistance between output adjust (pin output common (pin will determine magnitude increase output. table above only applicable HR151-2805.
Output Voltage (Auxiliary output triple output models)
B4-46
22811-009-DTS 2010 technical information believed accurate, responsibility assumed errors omissions. Interpoint reserves right make changes products specifications without notice. HR150 Series trademark Interpoint. Copyright 1990 1999 Interpoint. rights reserved.
CASES
case indicates
CASE
CASE BOTTOM VIEW Figures configurations.
1.125 (28.58)
2.125 (53.98)
Materials Header Cold Rolled Steel/Nickel/Gold cases Cold Rolled Steel/Nickel/Tin cases Cover Kovar/Nickel cases Cold Rolled Steel/Nickel/Tin cases Pins alloy ceramic seal case case (except Series Single Dual) compression glass seal Series Single Dual case Case dimensions inches (mm) Tolerance ±0.005 (0.13) three decimal places ±0.01 (0.3) decimal places unless otherwise specified
CAUTION Heat from reflow wave soldering damage device. Solder pins individually with heat application exceeding 300°C seconds pin.
FIGURE CASE MAXIMUM DIMENSIONS
BOTTOM VIEW CASE Filter: Screening Standard, SFMC Filter: Screening Space Standard,
Seam Seal
0.040 (1.02) 1.110 (28.19) 0.955 (24.26) 0.555 (14.1) 0.155 (3.94) 0.000 0.400 max. (10.16) 0.000 0.25 ±0.03 (6.4 ±0.8) 0.000 0.245 (6.22) 1.845 (46.86) 2.090 (53.01)
Squared corner case indicate one.
FIGURE CASE
Note: Although every effort been made render case drawings actual size, variations printing process cause some distortion. Please refer numerical dimensions accuracy.
B8-17
CASES
BOTTOM VIEW CASE FMA-461and FMB-461 Filter: Screening Standard
Solder Seal
1.120 (28.45) 0.960 (24.38) 0.040 (1.02) 0.560 (14.22)
CASE
Squared corner case indicate one.
Solder Tip-off
0.160 (4.06) 0.000 0.25 +0.05/-0.00 (6.4 +1.3/-0.0) 1.855 (47.12) 0.655 (16.64) 1.055 (26.80) 1.455 (36.96) 0.495 (12.57) 2.110 (53.59) 2.110 (53.59) 0.000 0.000 0.255 (6.48)
FIGURE CASE
BOTTOM VIEW CASE Series: Screening Standard HR151 Series HR152 Series: screening options
Solder Seal
1.120 (28.45) 0.960 (24.38) 0.040 (1.02)
case indicates
Solder Tip-off
0.160 (4.06) 0.000 0.000 0.255 (6.48) 0.495 (12.57) 0.25 +0.05/-0.00 (6.4 +1.3/-0.0) 1.855 (47.12) 0.000
FIGURE CASE
B8-21
CASE
CASES
case indicates Materials Header Case Cold Rolled Steel/Nickel/Gold Cases Cold Rolled Steel/Nickel/Tin Cover Case Kovar/Nickel Cases Cold Rolled Steel/Nickel/Tin Pins alloy (all cases) Series Triple compression glass seal Series Triple, case ceramic seal Series Triple, case compression glass seal HUM40 compression glass seal ceramic seal Case compression glass seal Case compression glass seal ceramic seal Case dimensions inches (mm) Tolerance ±0.005 (0.13) three decimal places ±0.01 (0.2) decimal places unless otherwise specified
CASE BOTTOM VIEW Figures configuration
1.350 (34.29)
1.950 (49.53) CAUTION Heat from reflow wave soldering damage device. Solder pins individually with heat application exceeding 300°C seconds pin.
FIGURE CASE MAXIMUM DIMENSIONS
BOTTOM VIEW CASE Series Triple Series Triple: Screening Standard,
Bathtub Platform case indicates
1.170 (29.72) 0.040 dia. (1.02) Series Series
Seam Seal
0.170 (4.32) 0.000 0.25 (6.4) 0.405 (10.29) 0.000 0.000 0.170 (4.32)
0.570 (14.48)
0.970 (24.64)
1.370 (34.80)
0.405 (10.29)
Note: Although every effort been made render case drawings actual size, variations printing process cause some distortion. Please refer numerical dimensions accuracy.
B8-12
0.25 (6.4)
FIGURE CASE
1.770 (44.96)
0.000
CASE
CASES
BOTTOM VIEW CASE Series: Screening Standard HR153 Series: screening options
Solder Seal
1.170 (29.72) 0.040 dia. (1.02)
Squared corner case indicate one.
Solder Tip-off
0.170 (4.32) 0.000 0.505 (12.83) 0.250/0.300 (6.35/7.62) 0.000 0.000
0.170 (4.32)
0.570 (14.48)
0.970 (24.64)
1.370 (34.80)
FIGURE CASE
B8-14
1.770 (44.96)
SCREENING PRODUCTS
PRODUCTS
TEST products) PRE-CAP INSPECTION Method 2017 FINAL ELECTRICAL TEST MIL-PRF-38534, Group Subgroups +25°C case HERMETICITY TESTING Gross Leak, 10-3) FINAL VISUAL INSPECTION Method 2009 STANDARD
Test methods referenced MIL-STD-883 determined MILPRF-38534.
Applies following products: HR700 Series HR300 Series HR150 Series HR120 Series HR40 Series
C2-13

DC/DC CONVERTERS VOLT INPUT HR150 SERIES WATT MODELS OU

Top Searches for this datasheet

Other recent searches