Model 2771AM3 Allows High Impedance Piezoelectric Accelerometer C

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

Model 2771AM3 Allows High Impedance Piezoelectric Accelerometer C

Datasheet Thumbnail

Top Searches for this datasheet

Remote Charge Convertor
Model 2771AM3
Allows High Impedance Piezoelectric Accelerometer Constant Current Mode Attaches Directly Signal Analyzer Inputs Wide Frequency Response Noise Operation Rugged, Small Package Economical
ENDEVCO
MODEL 2771AM3
Actual size
ENDEVCO® Model 2771AM3 Remote Charge Convertor (RCC) noise, two-wire, single-ended device, designed allow high impedance piezoelectric transducers used with many popular signal analyzers/signal conditioners that feature built-in constant current source. Attached directly inputs analyzer signal conditioner, this device transforms high impedance charge input, such signal from high temperature piezoelectric accelerometer, into impedance voltage proportional transducer's charge. This powered constant current source inside analyzer signal conditioner; voltage output feeds same connection that supplies power. Model 2771AM3 rugged lightweight. outstanding signal-to-noise ratio frequency response. unit designed handle maximum source capacitance (transducer cable capacitance) 5000
Signal Analyzer With Built-In Constant Current Source Model 2771AM3 Charge Mode Piezoelectric Accelerometer
ISOTRON Compatible Signal Conditioner
Data Recorder Analyzer
Model 2771AM3
Charge Mode Piezoelectric Accelerometer
Typical Applications
APPLIES CALIFORNIA FACILITY
ENDEVCO
Remote Charge Convertor
SPECIFICATIONS
INPUTS TYPE INPUT IMPEDANCE SOURCE CAPACITANCE OVERLOAD PROTECTION OUTPUTS TYPE OUTPUT IMPEDANCE OUTPUT BIAS LINEAR OUTPUT VOLTAGE LINEAR OUTPUT CURRENT TRANSFER CHARACTERISTICS GAIN GAIN SOURCE CAPACITANCE FREQUENCY RESPONSE Lower Cutoff Frequency Upper Cutoff Frequency AMPLITUDE LINEARITY RESIDUAL NOISE WARM-UP POWER CURRENT REQUIREMENT COMPLIANCE VOLTAGE PHYSICAL DIMENSIONS WEIGHT CASE MATERIAL CONNECTION ENVIRONMENTAL TEMPERATURE HUMIDITY Single-ended, piezoelectric charge mode 5000 250,000 shock input
MODEL 2771AM3
Single-ended, side connected circuit ground 11.5VDC 12.5VDC, +75°F (+24°C) volts pk-pk (3.535 rms) greater pk-pk greater
1.00 mV/pC, ±0.1% change 1000 Within from kHz, reference -3db (typical) kHz, -3db (typical) reading from best straight line approximation rms, broadband, sec. within ±10% final bias level
Powered constant current supply
Outline Drawing typical Stainless steel Output male, Input 10-32 UNF-2B
Operating Storage R.H.
+32°F +185°F +85°C) -67°F +302°F (-55°C +150°C)
ACCESSORY EHM486
CAP, PROTECTIVE
MATES WITH ENDEVCO 3000 SERIES CABLES WITH 10-32 UNF-2B CONNECTOR
NOTES Model 2771AM3 designed attached popular signal analyzers signal conditioners that feature built-in constant current power supply. applications that require stand-alone installation (the located distance away from constant current source), Model 2771A-X should considered. Maintain high levels precision accuracy using Endevco's factory calibration services. Call Endevco's inside sales force 800-982-6732 recommended intervals, pricing turn-around time these services well quotations standard products.
2.50 (53.3) (63.5)
(14.0)
UNIT IDENTIFICATION CONNECTOR CLEAR SHRINK TUBING
Continued product improvement necessitates that Endevco reserve right modify these specifications without notice. Endevco maintains program constant surveillance over products ensure high level reliability. This program includes attention reliability factors during product design, support stringent Quality Control requirements, compulsory corrective action procedures. These measures, together with conservative specifications have made name Endevco synonymous with reliability. ENDEVCO CORPORATION, 30700 RANCHO VIEJO ROAD, JUAN CAPISTRANO, 92675 (800) 982-6732 (949) 493-8181 (949) 661-7231 www.endevco.com Email:applications@endevco.com 1100

Model 2771AM3 Allows High Impedance Piezoelectric Accelerometer C

Top Searches for this datasheet

Other recent searches