Allows Wireless Transmission ON/OFF Signals from Input Devices Power I

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

Allows Wireless Transmission ON/OFF Signals from Input Devices Power I

Datasheet Thumbnail

Top Searches for this datasheet

Inductive Power Couplers
Allows Wireless Transmission ON/OFF Signals from Input Devices Power Input Devices electromagnetic coupler
transmit input signals Output Unit
B7AP
Supplies power Input Unit,
which means does require independent power supply
Wireless signal power transmission
through nonmetal object (such plastic glass) possible
Ordering Information
Classification Stationary Unit Appearance Transmission distance (couplers)
8±1.5
delay Typical: 19.2 Max.:
Part number B7AP-S1 (See Note.)
Moving Unit
(0.32 ±0.06
B7AP-M1
Note: B7AP-S1 Power Coupler gauge that used adjust transmission distance between B7AP-S1 B7AP-M1 Power Couplers.
B7AP
MODELS
Applicable Link Terminal B7A-R6B31 B7A-R6C31 B7A-R6F31 B7A-R6G31 B7A-R6A52 (See Note B7A-R6A33 B7A-R3A33 B7AS-R6B31 B7AM-6BS (See Note B7A-T6j1 B7A-T6D2 B7A-T6E3 B7A-T3E3 B7AS-T6B1 B7AM-6BS (16) (16) (16) (16) (16) (16) Two-wire sensor, contact Two-wire sensor, contact Contact B7AP-M1 Max. points (See Note (See Note Applicable input device (See Note -Part number B7AP-S1
B7AP
Note: maximum points refers maximum points handled simultaneously Input Output Units. Figures parentheses indicate maximum points handled simultaneously Input Output Units each connected with independent power supply. Refer Power Supplies Operation Section this data sheet. maximum points same maximum input points Input Unit connected B7AP-M1. PLCs three-wire sensors connected only Input Output Units each connected with independent power supply. Refer Power Supplies Operation Section this data sheet. error processing LOAD-OFF mode.
Specifications
COMMUNICATIONS SPECIFICATIONS
Communication method Transmission distance (couplers) Transmission distance (B7A) delay Minimum coupler interfacing time Minimum distance between Power Couplers mounted parallel Unidirectional, time-division multiplex 8±1.5 (0.32 0.06 max. (328 Note Typical: 19.2 max. (See Note (2.36
Note: value case where power supply provided only B7AP-S1. Minimum coupler interfacing time minimum time required signal power transmission between B7AP-S1 B7AP-M1 Power Couplers.
B7AP
CHARACTERISTICS
Part number Power supply voltage Current consumption Insulation resistance Dielectric strength Noise immunity Vibration resistance Shock resistance Ambient temperature Ambient humidity Cable pulling strength tightening strength Enclosure rating Maximum cable length Weight Operating Storage Operating B7AP-S1 ±10% B7AP-M1
B7AP
min. VDC) between each lead wire external parts 1,000 VAC, 50/60 between each lead wire external parts Noise level: pulse width: transmission line coupling) 1.5-mm double amplitude m/s2 (1640.4 ft/sec2) approx. 10°C 55°C (14°F 131°F) with icing condensation 25°C 65°C 13°F 149°F) with icing condensation (with condensation) kgf) lbs) (400 (28.7 lbf) IP67 (78.7 Approx. (10.58 Radiated Emissions: Radiated Immunity: Electrostatic Discharge: Burst Transients: EN55022 class prEN50082-2 prEN50082-2 prEN50082-2 Approx. (8.11
Approved standards
UL508 Conforms EN50081-2, EN50082-2
MOVING UNIT SPECIFICATIONS
Output voltage Output current ±10%
Note: Moving Unit that total current consumption input devices max. power supplied input devices through Moving Unit.
Engineering Data
TRANSMISSION RANGE (REFERENCE)
Transmission distance (mm)
Available zone
max.
Distance between axes (mm)
B7AP
B7AP
Operation
CONNECTION
VDC±10% Brown Black Blue Output Unit B7AP-S1 B7AP-M1 Brown Black Blue Input Unit
POWER SUPPLIES
Signal Power Transmission (with Power Supplied B7AP-S1)
Transmission distance: 8±1.5 (0.315 ±0.059) Brown Black Blue
(standard)
VDC±10% Brown Black Blue Output Unit Extension cable max.)
(standard)
Input Unit
Total length: max.
Note: thickness extension cable B7AP-S1 Power Coupler must 0.75 min. extension cable connected B7AP-M1 Power Coupler. original cable connected B7AP-M1 Power Coupler. Refer page Models maximum input points Input Unit. three-wire sensor connected Input Unit.
Signal Transmission Only (with Power Supplied B7AP-S1 B7AP-M1)
Transmission distance: 8±1.5 VDC±10% Brown Black Blue Output Unit Extension cable (standard) max.)
Open connection) Brown
Input Unit
Black Blue
(standard)
Total length: max.
Extension cable (400m max.)
Note: thickness extension cable B7AP-S1 B7AP-M1 Power Coupler must 0.75 min. transmitting signals only, brown lead wire B7AP-M1 Power Coupler must used. Insulate brown lead wire with insulation tape that brown wire will come contact with lead wire. maximum input points Input Unit available. PLCs three-wire sensors connected Input Unit.
B7AP
INDICATORS
Indicators Power indicator (B7AP-S1) Operation indicator (B7AP-M1) Function when power supplied Power Coupler. when power supplied Power Coupler.
B7AP
when B7AP-M1 B7AP-S1 Power Couplers properly wireless signal power transmission transmission distance ±1.5 (0.32 ±0.06). when B7AP-M1 B7AP-S1 Power Couplers properly wireless signal power transmission, B7AP-M1 Power Coupler excessive loads.
B7AP-S1
Power indicator
B7AP-M1
Operation indicator
Dimensions
Unit: (inch)
B7AP-S1
(1.65) (1.42) (3.86) 85.3 (3.36) (3.15) (0.51) Toothed washer (0.39)
Power indicator Round vinyl-insulated cable dia. (0.5 Standard length:
27.3 (1.08)
Two, clamping (0.20)
Mounting Holes
30.5 +0.5 dia. (1.2
+0.019
dia.)
B7AP-M1
(1.65) (1.42)
(2.40) 48.3 (1.90) (1.69) Toothed washer (0.51)
Operation indicator Round vinyl-insulated cable dia. (0.5 Standard length:
27.3 (1.08)
Mounting Holes
Two, clamping (0.20) 30.5 (1.2
+0.5
dia. dia.)
+0.019
B7AP
B7AP
Precautions
GENERAL PRECAUTIONS
careful when touching B7AP-S1 Power Coupler during operation because surface temperature B7AP-S1 Power Coupler will rise approximately 20°C after B7AP-S1 Power Coupler starts power transmission. surface temperature varies with load sensing device connected B7AP-M1 Power Coupler transmission distance. Wire cables B7AP-S1 B7AP-M1 Power Couplers through independent metal conduits prevent Power Couplers from being influenced noise there power high-tension lines nearby. Test Power Couplers make sure that Power Couplers operate normally before they actual operation. Correct
Metal conduit
Incorrect
HANDLING
B7AP-S1 B7AP-M1 Power Couplers with available Link Terminals. Refer page Models. M7E-12jj Display Unit, M7E-20jj Display Unit, Link Terminals with delay cannot used with B7AP-S1 B7AP-M1 Power Coupler. LOAD-OFF model Output Unit connected B7AP-S1. When using model that allows selection error processing, LOAD-OFF mode. This turns signals right before occurrence transmission error prevents unexpected signal transmission when transmission error cleared. Separate Power Couplers 8±1.5 min. away from each other. distance between Power Couplers standby must more.
min.
Power high-tension line
subject head B7AP-S1 B7AP-M1 Power Coupler excessive shock with hard objects.
B7AP-S1 B7AP-M1 Power Coupler outdoors unless properly protected.
supply power B7AP-S1 B7AP-M1 Power Coupler while connecting Power Couplers Link Terminals. Connect Power Couplers Link Terminals correctly, otherwise internal circuits Power Couplers damaged. terminal must contact with power supply terminals, otherwise internal elements damaged normal transmission possible.
Brown(+) Black(SIG) Blue(- Contact Brown(+) Black(SIG) Blue(- Black(SIG) Brown(+) Blue(-
B7AP-S1 B7AP-M1 Power Couplers products meeting requirements IP67. B7AP-S1 B7AP-M1 Power Coupler cannot however, used water oil. Keep heads B7AP-S1 B7AP-M1 Power Couplers free from dust, otherwise improper signal power transmission result between Power Couplers.
Correct
MOUNTING
Incorrect nuts serrated toothed washers tighten nuts mount B7AP-S1 B7AP-M1 Power Couplers. tightening torque applied each nuts must (28.7 lbf) maximum. mounting position will change improper signal power transmission result between Power Couplers nuts tightened properly.
(28.7 lbf) max.
Incorrect
B7AP
TRANSMISSION DISTANCE STABLE SIGNAL POWER TRANSMISSION
B7AP-S1 Power Coupler gauge that used adjust transmission distance between B7AP-S1 B7AP-M1 Power Couplers. gauge adjust transmission distance make sure that green operation indicator B7AP-M1 Power Coupler lit, Output Unit error output before operating Power Couplers.
Gauge Operation indicator
B7AP
EFFECTS SURROUNDING METAL
B7AP Power Coupler malfunction when affected surrounding metal. When mounting B7AP within metal panel, ensure that clearances given following table maintained. sure check advance that B7AP operates correctly.
dia.
Item
B7AP-S1 (0.79 dia. (2.36 (0.79 (2.36
B7AP-M1 (0.79 dia. (2.36 (0.79 (2.36
MONITORING TRANSMISSION STATUS
Judge from power supply/error indicator error output Output Unit whether B7AP-S1 B7AP-M1 Power Couplers facing each other correctly. error output Output Unit will when B7AP-S1 B7AP-M1 Power Couplers facing each other correctly.
MAINTENANCE
Regularly check these items stable operation B7AP-S1 B7AP-M1 Power Couplers: mounting positions tightening mounting nuts. tightening, contacts, breaking lead wires. Dust accumulation heads. ambient operating temperature other operating conditions. transmission distance.
MINIMUM DISTANCE BETWEEN POWER COUPLERS MOUNTED PARALLEL
When mounting B7AP-S1 B7AP-M1 Power Couplers parallel, refer following table. Keep least specified minimum distance between adjacent Power Couplers proper heat radiation considering temperature rise (approximately 20°C) B7AP-S1 Power Couplers operation.
Item
B7AP-S1 (2.36
B7AP-M1 (2.36
B7AP
B7AP
NOTE: DIMENSIONS SHOWN MILLIMETERS. convert millimeters inches divide 25.4.
OMRON ELECTRONICS
1-800-55-OMRON
Cat. CEDSAX4 11/01
East Commerce Drive Schaumburg, 60173
OMRON LINE Global http://www.omron.com http://www.omron.com/oei Canada http://www.omron.com/oci
OMRON CANADA, INC.
416-286-6465
Milner Avenue Scarborough, Ontario
Specifications subject change without notice.
Printed U.S.A

Allows Wireless Transmission ON/OFF Signals from Input Devices Power I

Top Searches for this datasheet

Other recent searches