Powered CMOS RS-232 Drivers/Receivers ADM223/ADM230L-ADM241L ADM2

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

Powered CMOS RS-232 Drivers/Receivers ADM223/ADM230L-ADM241L ADM2

Datasheet Thumbnail

Top Searches for this datasheet

FEATURES Single Power Supply Meets EIA-232-E V.28 Specifications kB/s Data Rate On-Board DC-DC Converters Output Swing with Supply Small Capacitors Power Shutdown Receivers Active Shutdown (ADM223) Receiver Input Levels Latch-Up FREE Plug-In Upgrade MAX223/230-241 Plug-In Upgrade AD230-AD241 APPLICATIONS Computers Peripherals Modems Printers Instruments GENERAL DESCRIPTION
Powered CMOS RS-232 Drivers/Receivers ADM223/ADM230L-ADM241L
ADM232L TYPICAL OPERATING CIRCUIT
INPUT +10V VOLTAGE DOUBLER +10V -10V VOLTAGE INVERTER 6.3V 6.3V 6.3V
T1OUT T2OUT R1IN R2IN RS-232 INPUTS** RS-232 OUTPUTS
TTL/CMOS INPUTS*
T1IN T2IN R1OUT R2OUT
TTL/CMOS OUTPUTS
ADM232L
INTERNAL 400k PULL-UP RESISTOR EACH TTL/CMOS INPUT. INTERNAL PULL-DOWN RESISTOR EACH RS-232 INPUT.
ADM2xx family line drivers/receivers intended EIA-232-E V.28 communications interfaces, especially applications where available. ADM223, ADM230L, ADM235L, ADM236L ADM241L feature power shutdown mode that reduces power dissipation less than making them ideally suited battery powered equipment. receivers remain enabled during shutdown ADM223. ADM233L ADM235L require external components particularly useful applications where printed circuit board space critical.
members ADM230L family, except ADM231L ADM239L, include internal charge pump voltage converters that allow operation from single supply. These converters convert input power required RS-232 output levels. ADM231L ADM239L designed operate from supplies. internal charge pump voltage converter generates supply. ADM2xxL enhanced upgrade AD2xx family featuring lower power consumption, faster slew rate operation with smaller capacitors.
Table Selection Table
Part Number ADM223 ADM230L ADM231L ADM232L ADM233L ADM234L ADM235L ADM236L ADM237L ADM238L ADM239L ADM241L REV.
Power Supply Voltage 13.2 13.2
RS-232 Drivers
RS-232 Receivers
External Capacitors None None
Power Shutdown (SD) (SD)
Three-State (EN)
Pins
Information furnished Analog Devices believed accurate reliable. However, responsibility assumed Analog Devices use, infringements patents other rights third parties that result from use. license granted implication otherwise under patent patent rights Analog Devices.
Technology Way, P.O. 9106, Norwood, 02062-9106, U.S.A. Tel: 781/329-4700 www.analog.com Fax: 781/326-8703 Analog Devices, Inc., 2001
(ADM223, ADM231L, ADM232L, ADM234L, ADM236L, ADM238L, ADM239L, ADM241L); (ADM230L, ADM233L, ADM235L, ADM237L); 13.2 (ADM231L ADM239L); C1-C4 Ceramic. Specifications TMIN TMAX unless otherwise noted.)
0.05 0.25 Unit Volts V/µs
Parameter Output Voltage Swing Power Supply Current Power Supply Current Shutdown Supply Current Input Logic Threshold Low, VINL Input Logic Threshold High, VINH Logic Pull-Up Current RS-232 Input Voltage Range1 RS-232 Input Threshold RS-232 Input Threshold High RS-232 Input Hysteresis RS-232 Input Resistance TTL/CMOS Output Voltage Low, TTL/CMOS Output Voltage High, TTL/CMOS Output Leakage Current Output Enable Time (TEN) Output Disable Time (TDIS) Propagation Delay Transition Region Slew Rate Output Resistance RS-232 Output Short Circuit Current
NOTES Guaranteed design. Specifications subject change without notice.
Test Conditions/Comments Transmitter Outputs Loaded with Ground Load, (ADM232L only) Load Load, ADM231L ADM239L Only TIN, TIN,
85°C IOUT -1.0 VCC, ROUT ADM223, ADM235L, ADM236L, ADM239L, ADM241L (Figure ADM223, ADM235L, ADM236L, ADM239L, ADM241L (Figure RS-232 2500 Measured from VOUT
ABSOLUTE MAXIMUM RATINGS*
25°C unless otherwise noted)
-0.3 (VCC +0.3 Input Voltages -0.3 (VCC Output Voltages TOUT (V+, (V-, ROUT -0.3 (VCC Short Circuit Duration TOUT Continuous Power Dissipation N-14 (Derate mW/°C above 70°C) N-16 (Derate 10.5 mW/°C above 70°C) N-20 (Derate mW/°C above 70°C) N-24 (Derate 13.5 mW/°C above 70°C) 1000 N-24A (Derate 13.5 mW/°C above 70°C) R-16 SOIC (Derate mW/°C above 70°C) R-20 SOIC (Derate mW/°C above 70°C) R-24 SOIC (Derate mW/°C above 70°C) R-28 SOIC (Derate 12.5 mW/°C above 70°C) RS-28 SSOP (Derate mW/°C above 70°C) Q-14 Cerdip (Derate mW/°C above 70°C) Q-16 Cerdip (Derate mW/°C above 70°C) Q-20 Cerdip (Derate 11.2 mW/°C above 70°C) Q-24 Cerdip (Derate 12.5 mW/°C above 70°C) 1000 D-24 Ceramic (Derate mW/°C above 70°C) 1000
Thermal Impedance, N-14 140°C/W N-16 135°C/W N-20 125°C/W N-24 120°C/W N-24A 110°C/W R-16 SOIC 105°C/W R-20 SOIC 105°C/W R-24 SOIC 85°C/W R-28 SOIC 80°C/W RS-28 SSOP 100°C/W Q-14 Cerdip 105°C/W Q-16 Cerdip 100°C/W Q-20 Cerdip 100°C/W Q-24 Cerdip 55°C/W D-24 Ceramic 50°C/W Operating Temperature Range Commercial Version) 70°C Industrial Version) -40°C +85°C Storage Temperature Range -65°C +150°C Lead Temperature, Soldering 300°C Vapor Phase sec) 215°C Infrared sec) 220°C
*This stress rating only; functional operation device these other conditions above those indicated operational sections this specification implied. Exposure absolute maximum rating conditions extended periods time affect reliability.
REV.
ADM223/ADM230L-ADM241L
ORDERING GUIDE
Model ADM223 ADM223AR ADM223ARS Temperature Range -40°C +85°C -40°C +85°C Package Option* R-28 RS-28 Model ADM230L ADM230LJN ADM230LJR ADM230LAN ADM230LAR ADM230LAQ ADM233L ADM233LJN ADM233LAN Temperature Range 70°C 70°C -40°C +85°C -40°C +85°C -40°C +85°C 70°C -40°C +85°C Package Option* N-20 R-20 N-20 R-20 Q-20 N-20 N-20 Model ADM231L ADM231LJN ADM231LJR ADM231LAN ADM231LAR ADM231LAQ ADM234L ADM234LJN ADM234LJR ADM234LAN ADM234LAR ADM234LAQ ADM237L ADM237LJN ADM237LJR ADM237LAN ADM237LAR ADM237LAQ ADM241L ADM241LJR ADM241LAR ADM241LJRS ADM241LARS Temperature Range 70°C 70°C -40°C +85°C -40°C +85°C -40°C +85°C 70°C 70°C -40°C +85°C -40°C +85°C -40°C +85°C 70°C 70°C -40°C +85°C -40°C +85°C -40°C +85°C 70°C -40°C +85°C 70°C -40°C +85°C Package Option* N-14 R-16 N-14 R-16 Q-14 N-16 R-16 N-16 R-16 Q-16 N-24 R-24 N-24 R-24 Q-24 R-28 R-28 RS-28 RS-28
ADM232L ADM232LJN ADM232LJR ADM232LAN ADM232LAR ADM232LAQ
70°C 70°C -40°C +85°C -40°C +85°C -40°C +85°C
N-16 R-16 N-16 R-16 Q-16 N-24A N-24A D-24
ADM235L ADM235LJN 70°C ADM235LAN -40°C +85°C ADM235LAQ -40°C +85°C
ADM236L ADM236LJN ADM236LJR ADM236LAN ADM236LAR ADM236LAQ ADM239L ADM239LJN ADM239LJR ADM239LAN ADM239LAR ADM239LAQ
70°C 70°C -40°C +85°C -40°C +85°C -40°C +85°C 70°C 70°C -40°C +85°C -40°C +85°C -40°C +85°C
N-24 R-24 N-24 R-24 Q-24 N-24 R-24 N-24 R-24 Q-24
ADM238L ADM238LJN ADM238LJR ADM238LAN ADM238LAR ADM238LAQ
70°C 70°C -40°C +85°C -40°C +85°C -40°C +85°C
N-24 R-24 N-24 R-24 Q-24
Ceramic DIP; Plastic DIP; Cerdip; Small Outline (SOIC); Small Shrink Outline Package (SSOP).
CAUTION (electrostatic discharge) sensitive device. Electrostatic charges high 4000 readily accumulate human body test equipment discharge without detection. Although ADM223/ADM230L-ADM241L features proprietary protection circuitry, permanent damage occur devices subjected high-energy electrostatic discharges. Therefore, proper precautions recommended avoid performance degradation loss functionality.
WARNING!
SENSITIVE DEVICE
REV.
ADM223/ADM230L-ADM241L
INPUT 6.3V +10V VOLTAGE DOUBLER +10V -10V VOLTAGE INVERTER 6.3V 6.3V
T3OUT T1OUT T2OUT T2IN T1IN
CONNECT
T4OUT T5IN
T1OUT T2OUT T3OUT T4OUT T5OUT RS-232 OUTPUTS
T1IN T2IN TTL/CMOS INPUTS* T3IN T4IN T5IN
ADM230L
VIEW (Not Scale)
T5OUT T4IN T3IN
ADM230L
INTERNAL 400k
PULL-UP RESISTOR EACH TTL/CMOS INPUT.
Figure ADM230L DIP/SOIC Configuration
Figure ADM230L Typical Operating Circuit
T2OUT R2IN R2OUT T2IN
ADM231L
VIEW (Not Scale)
T1OUT
INPUT
R1IN R1OUT T1IN
+12V -12V VOLTAGE INVERTER
7.5V 13.2V
SOIC
T1IN
T1OUT RS-232 OUTPUTS
T2OUT R2IN R2OUT T2IN
CONNECT
TTL/CMOS INPUTS* T2IN R1OUT T2OUT R1IN
ADM231L
VIEW (Not Scale)
T1OUT R1IN
TTL/CMOS OUTPUTS R2OUT R2IN
RS-232 INPUTS**
R1OUT T1IN
ADM231L
INTERNAL 400k PULL-UP RESISTOR EACH TTL/CMOS INPUT. INTERNAL PULL-DOWN RESISTOR EACH RS-232 INPUT.
Figure ADM231L SOIC Configurations
Figure ADM231L Typical Operating Circuit (DIP Pinout)
REV.
ADM223/ADM230L-ADM241L
INPUT 6.3V +10V VOLTAGE DOUBLER +10V -10V VOLTAGE INVERTER 6.3V 6.3V
T2OUT R2IN
T1OUT RS-232 OUTPUTS T2OUT R1IN RS-232 INPUTS** R2IN
T1OUT
T1IN TTL/CMOS INPUTS* T2IN R1OUT TTL/CMOS OUTPUTS R2OUT
ADM232L
VIEW (Not Scale)
R1IN R1OUT T1IN T2IN R2OUT
ADM232L
INTERNAL 400k PULL-UP RESISTOR EACH TTL/CMOS INPUT. INTERNAL PULL-DOWN RESISTOR EACH RS-232 INPUT.
Figure ADM232L DIP/SOIC Configuration
Figure ADM232L Typical Operating Circuit
INPUT
T1IN TTL/CMOS INPUTS*
T2IN T1IN R1OUT R1IN T1OUT R2OUT R2IN T2OUT
T1OUT RS-232 OUTPUTS T2OUT R1IN RS-232 INPUTS** R2IN
T2IN R1OUT TTL/CMOS OUTPUTS R2OUT MAKE CONNECTIONS THESE PINS INTERNAL -10V POWER SUPPLY INTERNAL +10V POWER SUPPLY
ADM233L
VIEW (Not Scale)
ADM233L
INTERNAL 400k PULL-UP RESISTOR EACH TTL/CMOS INPUT. INTERNAL PULL-DOWN RESISTOR EACH RS-232 INPUT.
Figure ADM233L Configuration
Figure ADM233L Typical Operating Circuit
REV.
ADM223/ADM230L-ADM241L
INPUT 6.3V
6.3V
+10V VOLTAGE DOUBLER +10V -10V VOLTAGE INVERTER
6.3V
T1OUT T2OUT T2IN T1IN
T3OUT T4OUT T4IN T3IN
T1OUT T2OUT RS-232 OUTPUTS
T1IN T2IN TTL/CMOS INPUTS* T3IN T4IN
ADM234L
VIEW (Not Scale)
T3OUT T4OUT
ADM234L
INTERNAL 400k
PULL-UP RESISTOR EACH TTL/CMOS INPUT.
Figure ADM234L DIP/SOIC Configuration
Figure ADM234L Typical Operating Circuit
INPUT
T1IN T2IN
T1OUT T2OUT T3OUT T4OUT T5OUT R1IN R2IN R3IN R4IN R5IN RS-232 INPUTS** RS-232 OUTPUTS
T4OUT T3OUT T1OUT T2OUT R2IN R2OUT T2IN T1IN R1OUT
R3IN
R3OUT T5IN
TTL/CMOS INPUTS*
T3IN T4IN T5IN R1OUT R2OUT
ADM235L
VIEW (Not Scale)
T5OUT
R4IN R4OUT T4IN T3IN R5OUT R5IN
TTL/CMOS OUTPUTS
R3OUT R4OUT R5OUT
R1IN
ADM235L
INTERNAL 400k PULL-UP RESISTOR EACH TTL/CMOS INPUT. INTERNAL PULL-DOWN RESISTOR EACH RS-232 INPUT.
Figure ADM235L Configuration
Figure ADM235L Typical Operating Circuit
REV.
ADM223/ADM230L-ADM241L
INPUT 6.3V +10V VOLTAGE DOUBLER +10V -10V VOLTAGE INVERTER 6.3V 6.3V
T1OUT T2OUT T3OUT T4OUT R1IN R2IN R3IN RS-232 INPUTS** RS-232 OUTPUTS
T3OUT T1OUT T2OUT R1IN R1OUT T2IN T1IN
T4OUT R2IN R2OUT
T2IN T1IN
TTL/CMOS INPUTS* T3IN T4IN R1OUT TTL/CMOS OUTPUTS R2OUT R3OUT
ADM236L
VIEW (Not Scale)
T4IN
T3IN R3OUT R3IN
ADM236L
INTERNAL 400k PULL-UP RESISTOR EACH TTL/CMOS INPUT. INTERNAL PULL-DOWN RESISTOR EACH RS-232 INPUT.
Figure ADM236L DIP/SOIC Configuration
Figure ADM236L Typical Operating Circuit
INPUT
6.3V
+10V VOLTAGE DOUBLER +10V -10V VOLTAGE INVERTER
6.3V
6.3V
T3OUT T1OUT T2OUT R1IN R1OUT T2IN T1IN T4OUT R2IN R2OUT T5IN T5OUT
T1OUT T2OUT T3OUT T4OUT
T1IN T2IN TTL/CMOS INPUTS* T3IN T4IN T5IN R1OUT TTL/CMOS OUTPUTS R2OUT R3OUT
RS-232 OUTPUTS
ADM237L
VIEW (Not Scale)
T4IN T3IN R3OUT R3IN
T5OUT R1IN R2IN R3IN RS-232 INPUTS**
ADM237L
INTERNAL 400k PULL-UP RESISTOR EACH TTL/CMOS INPUT. INTERNAL PULL-DOWN RESISTOR EACH RS-232 INPUT.
Figure ADM237L DIP/SOIC Configuration
Figure ADM237L Typical Operating Circuit
REV.
ADM223/ADM230L-ADM241L
INPUT 6.3V +10V VOLTAGE DOUBLER +10V -10V VOLTAGE INVERTER 6.3V 6.3V
T1OUT T2OUT T3OUT T4OUT R1IN R2IN RS-232 INPUTS** RS-232 OUTPUTS
T2OUT T1OUT R2IN R2OUT T1IN R1OUT R1IN
T3OUT
T1IN T2IN TTL/CMOS INPUTS* T3IN T4IN R1OUT R2OUT TTL/CMOS OUTPUTS R3OUT R4OUT
R3IN R3OUT T4IN T4OUT
ADM238L
VIEW (Not Scale)
T3IN
T2IN R4OUT R4IN
R3IN R4IN
ADM238L
INTERNAL 400k PULL-UP RESISTOR EACH TTL/CMOS INPUT. INTERNAL PULL-DOWN RESISTOR EACH RS-232 INPUT.
Figure ADM238L DIP/SOIC Configuration
Figure ADM238L Typical Operating Circuit
INPUT +12V -12V VOLTAGE INVERTER 7.5V 13.2V INPUT
R1OUT R1IN R5IN R5OUT R4OUT R4IN
T1IN T2IN R2OUT R2IN T2OUT
TTL/CMOS INPUTS*
T1IN T2IN T3IN R1OUT R2OUT TTL/CMOS OUTPUTS R3OUT R4OUT R5OUT
T1OUT T2OUT T3OUT R1IN R2IN R3IN R4IN R5IN RS-232 INPUTS** RS-232 OUTPUTS
ADM239L
VIEW (Not Scale)
T1OUT R3IN R3OUT T3IN T3OUT
ADM239L
INTERNAL 400k PULL-UP RESISTOR EACH TTL/CMOS INPUT. INTERNAL PULL-DOWN RESISTOR EACH RS-232 INPUT.
Figure ADM239L DIP/SOIC Configuration
Figure ADM239L Typical Operating Circuit
REV.
ADM223/ADM230L-ADM241L
INPUT +10V VOLTAGE DOUBLER +10V -10V VOLTAGE INVERTER 6.3V 6.3V
T3OUT T1OUT T2OUT R2IN R2OUT T2IN T1IN R1OUT R1IN
T4OUT R3IN R3OUT R4IN
TTL/CMOS INPUTS* T1IN T2IN T3IN T4IN R1OUT R2OUT TTL/CMOS OUTPUTS R3OUT R4OUT R5OUT
T1OUT T2OUT T3OUT T4OUT R1IN R2IN R3IN R4IN R5IN RS-232 INPUTS** RS-232 OUTPUTS
ADM241L
VIEW (Not Scale)
R4OUT T4IN T3IN R5OUT R5IN
ADM241L
INTERNAL 400k PULL-UP RESISTOR EACH TTL/CMOS INPUT. INTERNAL PULL-DOWN RESISTOR EACH RS-232 INPUT.
Figure ADM241L SOIC/SSOP Configuration
Figure ADM241L Typical Operating Circuit
INPUT +10V VOLTAGE DOUBLER +10V -10V VOLTAGE INVERTER
6.3V
6.3V
T3OUT T1OUT T2OUT R2IN R2OUT T2IN T1IN R1OUT R1IN T4OUT R3IN R3OUT R4IN T4IN R1OUT R2OUT TTL/CMOS OUTPUTS R3OUT R4OUT R5OUT TTL/CMOS INPUTS* T2IN T3IN T1IN
T1OUT T2OUT T3OUT T4OUT R1IN R2IN R3IN R4IN R5IN RS-232 INPUTS** RS-232 OUTPUTS
ADM223
VIEW (Not Scale)
R4OUT T4IN
T3IN R5OUT R5IN
ADM223
INTERNAL 400k PULL-UP RESISTOR EACH TTL/CMOS INPUT. INTERNAL PULL-DOWN RESISTOR EACH RS-232 INPUT. NOTE: RECEIVERS REMAIN ACTIVE SHUTDOWN.
Figure ADM223 SOIC/SSOP Configuration
Figure ADM223 Typical Operating Circuit
REV.
ADM223/ADM230L-ADM241L
FUNCTION DESCRIPTION
Mnemonic
Function Power Supply Input ADM233L, ADM235L). Internally generated positive supply (+10 nominal) parts except ADM231L ADM239L. ADM231L, ADM239L requires external 13.2 supply. Internally generated negative supply (-10 nominal). Ground pin. Must connected (ADM231L ADM239L only). External capacitor terminal) connected this pin. (ADM231L ADM239L only). External capacitor terminal) connected this pin. (ADM230L, ADM232L, ADM234L, ADM236L, ADM237L, ADM238L, ADM241L) External capacitor terminal) connected this pin. (ADM233L) capacitor connected internally external connection this required. (ADM230L, ADM232L, ADM234L, ADM236L, ADM237L, ADM238L, ADM241L) External capacitor terminal) connected this pin. (ADM233L) capacitor connected internally external connection this required. (ADM230L, ADM232L, ADM234L, ADM236L, ADM237L, ADM238L, ADM241L) External capacitor terminal) connected this pin. (ADM233L) Internal capacitor connections, Pins must connected together. (ADM230L, ADM232L, ADM234L, ADM236L, ADM237L, ADM238L, ADM241L) External capacitor terminal) connected this pin. (ADM233L) Internal capacitor connections, Pins must connected together. Transmitter (Driver) Inputs. These inputs accept TTL/CMOS levels. internal pull-up resistor connected each input. Transmitter (Driver) Outputs. These RS-232 levels (typically Receiver Inputs. These inputs accept RS-232 signal levels. internal pull-down resistor connected each input. Receiver Outputs. These TTL/CMOS levels. Enable Input. Active ADM235L, ADM236L, ADM239L, ADM241L. Active high ADM223. This input used enable/disable receiver outputs. With high ADM223), receiver outputs enabled. With high ADM223), outputs placed high impedance state. This facility useful connecting microprocessor systems. Shutdown Input. Active high ADM235L, ADM236L, ADM241L. Active ADM223. With high ADM235L, ADM236L, ADM241L, charge pump disabled, receiver outputs placed high impedance state driver outputs turned off. With ADM223, charge pump disabled, driver outputs turned receivers except placed high impedance state. shutdown, power consumption reduces Connect. connections required this pin.
TOUT ROUT EN/EN
SD/SD
Table ADM235L, ADM236L, ADM241L Truth Table
Table ADM223 Truth Table
Status Normal Operation Normal Operation Shutdown
Transmitters T1-T5 Enabled Enabled Disabled
Receivers R1-R5 Enabled Disabled Disabled
Status Shutdown Shutdown Normal Operation Normal Operation
Transmitters Receivers T1-T4 R1-R3 Disabled Disabled Enabled Enabled Disabled Disabled Disabled Enabled Disabled Enabled Disabled Enabled
-10-
REV.
ADM223/ADM230L-ADM241L
LOADED
V+/V-
LOADED
LOAD CURRENT
Figure Charge Pump Current
Figure Transmitter Output Voltage
SLEW RATE
1500 2000 1000 LOAD CAPACITANCE 2500 3000 POSITIVE SLEW NEGATIVE SLEW
LOAD CURRENT
Figure Transmitter Slew Rate Load Capacitance
Figure Transmitter Output Voltage Current
IMPEDANCE
Figure Charge Pump Impedance
REV.
-11-
ADM223/ADM230L-ADM241L
INPUT
OUTPUT
5.00V 5.00V M50.0 5.00V EXITING 3.1V
5.00V
5.00V M1.00
800mV
Figure Charge Pump, Exiting Shutdown
Figure Transmitter Output Loaded Slew Rate
INPUT
OUTPUT
5.00V
5.00V M1.00
800mV
Figure Transmitter Output Unloaded Slew Rate
GENERAL INFORMATION
CIRCUIT DESCRIPTION
ADM223/ADM230L-ADM241L family RS-232 drivers/ receivers designed solve interface problems meeting EIA-232-E specifications while using single digital supply. EIA-232-E standard requires transmitters which will deliver minimum transmission channel receivers which accept signal levels down ADM223/ADM230L-ADM241L meet these requirements integrating step voltage converters level shifting transmitters receivers onto same chip. CMOS technology used keep power dissipation absolute minimum. comprehensive range transmitter/receiver combinations available cover most communications needs. ADM223, ADM230L, ADM235L, ADM236L ADM241L particularly useful battery powered systems they feature power shutdown mode which reduces power dissipation less than ADM233L ADM235L designed applications where space saving important charge pump capacitors molded into package. ADM231L ADM239L include only negative charge pump converter intended applications where positive available. facilitate sharing common line connection microprocessor data ADM235L, ADM236L, ADM239L ADM241L feature enable (EN, function. When disabled, receiver outputs placed high impedance state.
internal circuitry ADM230L-ADM241L consists three main sections. These are: charge pump voltage converter RS-232 TTL/CMOS receivers TTL/CMOS RS-232 transmitters
Charge Pump DC-DC Voltage Converter
charge pump voltage converter consists oscillator switching matrix. converter generates supply from input level. This done stages using switched capacitor technique illustrated Figures First, input supply doubled using capacitor charge storage element. level then inverted generate using storage element.
2VCC
INTERNAL OSCILLATOR
Figure Charge-Pump Voltage Doubler
-12-
REV.
ADM223/ADM230L-ADM241L
FROM VOLTAGE DOUBLER -(V+)
receivers except ADM223 into high-impedance disabled state. Receivers ADM223 remain enabled during shutdown. This feature allows monitoring external activity such ring indicator monitoring while device power shutdown mode. shutdown control input active high parts except ADM223 where active low. Refer Tables Enable Input ADM235, ADM239, ADM241L ADM223 feature enable input used enable disable receiver outputs. enable input active ADM235L, ADM239L, ADM241L active high ADM223. Refer Tables When disabled, receiver outputs placed high impedance state. This function allows outputs connected directly microprocessor data bus. also used allow receivers from different devices share common data line. timing diagram enable function shown Figure
3.5V ROUT 0.8V TDIS 0.1V 0.1V
INTERNAL OSCILLATOR
Figure Charge-Pump Voltage Inverter
Capacitors used reduce output ripple. Their values critical reduced higher levels ripple acceptable. charge pump capacitors also reduced expense higher output impedance supplies. supplies also used power external circuitry current requirements small.
Transmitter (Driver) Section
drivers convert TTL/CMOS input levels into EIA-232-E output levels. With driving typical EIA-232-E load, output voltage swing Even under worst-case conditions drivers guaranteed meet EIA-232-E minimum requirement. input threshold levels both CMOS compatible with switching threshold VCC/4. With nominal switching threshold 1.25 typical. Unused inputs left unconnected, internal pull-up resistor pulls them high forcing outputs into state. required EIA-232-E standard, slew rate limited less than V/µs without need external slew limiting capacitor output impedance power-off state greater than
Receiver Section
*POLARITY REVERSED ADM223.
Figure Enable Timing
APPLICATION HINTS Driving Long Cables
receivers inverting level shifters which accept EIA-232-E input levels translate them into TTL/ CMOS levels. inputs have internal pull-down resistors ground also protected against overvoltages guaranteed switching thresholds minimum maximum which well within EIA-232-E requirement. level threshold deliberately positive ensures that unconnected input will interpreted level. receivers have Schmitt trigger inputs with hysteresis level This ensures error-free reception both noisy inputs inputs with slow transition times.
Shutdown (SD)
accordance with EIA-232-E standard, long cables permissible provided that total load capacitance does exceed 2500 longer cables which exceed this, then possible trade baud rate cable length. Large load capacitances cause reduction slew rate, hence maximum transmission baud rate decreased. ADM230L-ADM241L designed that slew rate reduction with increasing load capacitance minimized. receivers, important that high level noise immunity inbuilt that slow rise fall times cause multiple output transitions signal passes slowly through transition region. ADM230L-ADM241L have hysteresis guard against this. This ensures that, even noisy environments, error-free reception achieved.
High Baud Rate Operation
ADM223, ADM230L, ADM235L, ADM236L ADM241L feature control input that used disable part reduce power consumption less than This very useful battery operated systems. During shutdown charge pump turned off, transmitters disabled
ADM230L-ADM241L feature high slew rates permitting data transmission rates well excess EIA-232-E specification. drivers maintain signal levels data rates 100-kB/s under worst-case loading conditions.
REV.
-13-
ADM223/ADM230L-ADM241L
OUTLINE DIMENSIONS
Dimensions shown inches (mm).
14-Lead Plastic (N-14)
14-Lead Cerdip (Q-14)
0.280 (7.11) 0.240 (6.10)
0.271 (6.89) 0.240 (6.09) 0.300 (7.62) 0.163 (4.14) 0.133 (3.378)
0.795 (20.19) 0.725 (18.42) 0.210 (5.33) 0.200 (5.05) 0.125 (3.18) 0.022 (0.558) 0.014 (0.356) 0.100 (2.54) 0.070 (1.77) 0.045 (1.15) 0.060 (1.52) 0.015 (0.38)
0.325 (8.25) 0.300 (7.62) 0.195 (4.95) 0.115 (2.93) 0.015 (0.381) 0.008 (0.204)
0.780 (19.81)
0.150 (3.81) SEATING PLANE
0.125 (3.17) 0.02 (0.5) 0.11 (2.79) 0.06 (1.52) 0.016 (0.406) 0.099 (2.28) 0.05 (1.27)
0.21 (5.33) 0.15 (3.81) SEATING PLANE 0.012 (0.305) 0.008 (0.203)
16-Lead Plastic (N-16)
16-Lead Cerdip (Q-16)
0.280 (7.11) 0.240 (6.10)
0.271 (6.89) 0.240 (6.09) 0.300 (7.62) 0.163 (4.14) 0.133 (3.378)
0.840 (21.33) 0.745 (18.93) 0.210 (5.33) 0.200 (5.05) 0.125 (3.18) 0.022 (0.558) 0.014 (0.356) 0.100 (2.54) 0.070 (1.77) 0.045 (1.15) 0.060 (1.52) 0.015 (0.38)
0.325 (8.25) 0.300 (7.62) 0.195 (4.95) 0.115 (2.93) 0.015 (0.381) 0.008 (0.204)
0.780 (19.81)
0.150 (3.81) SEATING PLANE
0.125 (3.17) 0.02 (0.5) 0.11 (2.79) 0.016 (0.406) 0.099 (2.28) 0.06 (1.52) 0.05 (1.27)
0.21 (5.33) 0.15 (3.81) SEATING PLANE 0.012 (0.305) 0.008 (0.203)
16-Lead SOIC (R-16)
0.299 (7.60) 0.291 (7.40) 0.419 (10.65) 0.404 (10.26)
0.413 (10.50) 0.348 (10.10)
0.107 (2.72) 0.089 (2.26)
0.364 (9.246) 0.344 (8.738)
0.010 (0.25) 0.004 (0.10)
0.050 (1.27)
0.018 (0.46) 0.014 (0.36)
0.015 (0.38) 0.007 (1.18)
0.045 (1.15) 0.020 (0.50)
-14-
REV.
ADM223/ADM230L-ADM241L
OUTLINE DIMENSIONS
Dimensions shown inches (mm).
20-Lead Plastic (N-20)
1.060 (26.90) 0.925 (23.50)
20-Lead Cerdip (Q-20)
0.97 (24.64) 0.935 (23.75)
0.280 (7.11) 0.240 (6.10)
0.28 (7.11) 0.24 (6.1) 0.18 (4.57) 0.125 (3.18)
0.060 (1.52) 0.015 (0.38) 0.210 (5.33) 0.200 (5.05) 0.125 (3.18) 0.022 (0.558) 0.014 (0.356) 0.100 (2.54) 0.150 (3.81) 0.070 (1.78) SEATING 0.045 (1.15) PLANE
0.325 (8.25) 0.300 (7.62) 0.195 (4.95) 0.115 (2.93)
0.32 (8.128) 0.29 (7.366)
0.20 (5.0) 0.14 (3.56) 0.15 (3.8) 0.125 (3.18) 0.02 (0.5) 0.016 (0.41) 0.11 (2.79) 0.09 (2.28) 0.07 (1.78) 0.05 (1.27) SEATING PLANE 0.011 (0.28) 0.009 (0.23)
0.015 (0.381) 0.008 (0.204)
LEAD IDENTIFIED NOTCH
20-Lead SOIC (R-20)
0.5118 (13.00) 0.4961 (12.60)
24-Lead Ceramic (D-24)
1.290 (32.77) 0.005 (0.13)
0.098 (2.49)
0.2992 (7.60) 0.2914 (7.40) 0.4193 (10.65) 0.3937 (10.00)
0.610 (15.49) 0.500 (12.70)
0.075 (1.91) 0.015 (0.38) 0.225 (5.72)
0.620 (15.75) 0.590 (14.99)
0.1043 (2.65) 0.0926 (2.35)
0.0291 (0.74) 0.0098 (0.25)
0.200 (5.08) 0.120 (3.05) 0.023 (0.58) 0.014 (0.36) 0.110 (2.79) 0.090 (2.29) 0.070 (1.78) 0.030 (0.76)
0.150 (3.81) SEATING PLANE
0.015 (0.38) 0.008 (0.20)
0.0118 (0.30) 0.0040 (0.10)
0.0500 (1.27)
0.0192 (0.49) 0.0125 (0.32) 0.0138 (0.35) 0.0091 (0.23)
0.0500 (1.27) 0.0157 (0.40)
24-Lead Plastic (N-24A) 24-Lead Plastic (N-24)
0.260 (6.61
0.001 0.03) 0.32 (8.128) 0.30 (7.62)
0.55 (13.97) 0.53 (13.47)
1.228 (31.19) 1.226 (31.14) 0.130 (3.30) 0.128 (3.25)
1.25 (31.75) 1.24 (31.5) (5.08) 0.175 (4.45) 0.12 (3.05) 0.02 (0.508) 0.105 (2.67) 0.065 (1.66) 0.015 (0.381) 0.095 (2.42) 0.045 (1.15) 0.16 (4.07) 0.14 (3.56)
0.606 (15.4) 0.594 (15.09)
SEATING 0.011 (0.28) PLANE 0.02 (0.5) 0.11 (2.79) 0.07 (1.78) 0.009 (0.23) 0.016 (0.41) 0.09 (2.28) 0.05 (1.27) NOTES LEAD IDENTIFIED NOTCH PLASTIC LEADS WILL EITHER SOLDER DIPPED PLATED ACCORDANCE WITH MIL-M-38510 REQUIREMENTS.
SEATING PLANE
0.012 (0.305) 0.008 (0.203)
REV.
-15-
ADM223/ADM230L-ADM241L
OUTLINE DIMENSIONS
Dimensions shown inches (mm).
24-Lead Cerdip (Q-24)
28-Lead SOIC (R-28)
0.708 (18.02) 0.696 (17.67)
0.320 (8.128) 0.290 (7.366)
1.290 (32.77) 0.225 (5.715) 0.180 (4.572)
0.299 (7.6) 0.291 (7.39)
0.414 (10.52) 0.398 (10.10)
0.125 SEATING (3.175) PLANE 0.012 (0.305) 0.070 (1.778) 0.021 (0.533) 0.110 (2.794) 0.008 (0.203) 0.065 (1.651) 0.020 (0.508) 0.015 (0.381) 0.090 (2.286) 0.055 (1.397) LEAD IDENTIFIED NOTCH. CERDIP LEADS WILL EITHER PLATED SOLDER DIPPED ACCORDANCE WITH MIL-M-38510 REQUIREMENTS.
0.096 (2.44) 0.089 (2.26)
0.03 (0.76) 0.02 (0.51)
0.01 (0.254) 0.006 (0.15)
0.05 (1.27)
0.019 (0.49) 0.014 (0.35)
0.013 (0.32) 0.009 (0.23)
0.042 (1.067) 0.018 (0.457)
LEAD IDENTIFIED DOT. SOIC LEADS WILL EITHER PLATED SOLDER DIPPED ACCORDANCE WITH MIL-M-38510 REQUIREMENTS.
24-Lead SOIC (R-24)
0.608 (15.45) 0.596 (15.13)
28-Lead SSOP (RS-28)
0.407 (10.34) 0.397 (10.08)
0.299 (7.6) 0.291 (7.39)
0.414 (10.52) 0.398 (10.10)
0.212 (5.38) 0.205 (5.207)
0.311 (7.9) 0.301 (7.64)
0.096 (2.44) 0.089 (2.26)
0.03 (0.76) 0.02 (0.51)
0.07 (1.78) 0.066 (1.67)
0.01 (0.254) 0.006 (0.15)
0.05 (1.27)
0.019 (0.49) 0.014 (0.35)
0.013 (0.32) 0.009 (0.23)
0.042 (1.067) 0.018 (0.447) 0.008 (0.203) 0.002 (0.050)
LEAD IDENTIFIED DOT. SOIC LEADS WILL EITHER PLATED SOLDER DIPPED ACCORDANCE WITH MIL-M-38510 REQUIREMENTS
0.037 (0.94) 0.022 (0.559) 0.009 (0.229) 0.005 (0.127) LEAD IDENTIFIED DOT. LEADS WILL EITHER PLATED SOLDER DIPPED ACCORDANCE WITH MIL-M-38510 REQUIREMENTS 0.0256 (0.65)
Location
Page
05/01 Data Sheet changed from REV. REV. Edits Test Conditions/Comments Specifications
Location Page
01/01 Data Sheet changed from REV. REV. Removed information from FEATURES SPECIFICATIONS changes Removed information from ABSOLUTE MAXIMUM RATINGS -16- REV.
PRINTED U.S.A.
ADM223/ADM230L-ADM241L-Revision History
C00070-0-6/01(B)
0.295 (7.493)

Powered CMOS RS-232 Drivers/Receivers ADM223/ADM230L-ADM241L ADM2

Top Searches for this datasheet

Other recent searches