STANDARD Slimline 0.145" 10-Character Matrix Serial Input Ad

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

STANDARD Slimline 0.145" 10-Character Matrix Serial Input Ad

Datasheet Thumbnail

Top Searches for this datasheet

SCD55100 YELLOW SCD55101 HIGH EFFICIENCY SCD55102 GREEN SCD55103 HIGH EFFICIENCY GREEN SCD55104
STANDARD
Slimline
0.145" 10-Character Matrix Serial Input Addressable Intelligent Display® Devices
Dimensions inches (mm)
1.500 max. (38.10) 0.150 0.080 (3.81) (2.03) .050 (1.27) typ. .394 ±.006 (10.0 ±.15) Indicator 1.350 (34.29) 5510X SIEMENS YYWW 0.160 ±.02 (4.06 ±.51) 0.200 (5.08) date code Intensity Code Category Seating Plane .018 (.46) typ.
0.145 (3.68)
.012 (.30) typ. .300 ±.020 (7.62 ±.51)
FEATURES Profile Package: Smaller than Industry Standard 10-Digit Display 0.145" (3.68 Matrix Characters Red, Yellow, High Efficiency Red, Green, High Efficiency Green Optimum Display Surface Efficiency (display area package ratio) Power-30% Less Power Dissipation than Format High Speed Data Input Rate: ROMless Serial Input, Addressable Display-Ideal User Defined Characters Built-in Decoders, Multiplexers Drivers Readable from Feet (1.8 meters) Wide Viewing Angle, Axis 55°, Axis Attributes: User Defined Characters Eight Dimming Levels Power Down Mode (<250 Hardware/Software Clear Function Lamp Test Internal External Clock End-Stackable Dual-in-line Plastic Package Capability
.100±.010 typ.(2.54±.25) Tol. non-cum. 1.300 ref. (33.02)
Dimension Seating Plane. Display matrix pins centered package outline. Display matrix centered array. Tolerance: .XXX .010 (.25)
DESCRIPTION SCD55100 (Red), SCD55101 (Yellow), SCD55102 (HER), SCD55103 (Green) SCD55104 (HEG) eight digit addressable matrix, Serial Input, Intelligent Display devices. 0.145" (3.68 high digits packaged rugged, high quality optically transparent, standard 0.3" spacing plastic DIP. on-board CMOS RAM, associated with LED, each generate User Defined Characters. reduced count, power requirement heat dissipation reduced 30%. Additionally Power Down Mode quiescent current SCD5510X designed work with Serial port most common microprocessors. multiplex Clock (CLK I/O) multiplex Clock Select (CLK SEL) pins offer user capability supply high speed external multiplex clock. This feature minimize audio in-band interference portable communication equipment eliminate visual synchronization effects found high vibration environments such avionics equipment.
2-125
Maximum Ratings Supply Voltage -0.5 +7.0 Input Voltage Levels Relative Ground -0.5 +0.5 Operating Temperature +85°C Storage Temperature. +100°C Maximum Solder Temperature 0.063" below Seating Plane, Relative Humidity 85°C .85% Maximum Number LEDs 100% Brightness Maximum Power Dissipation .1.7 Watts Junction Temperature 125°C (100 Maximum Input Current Figure Data write cycle
Figure view
LOAD TLDS DATA SDCLK TSDCW TSDCW TLDH
TSDCLK Period
Figure Instruction cycle
LOAD SDCLK DATA LOAD SDCLK DATA
Figure Maximum power dissipation temperature
Maximum Power Dissipation Watts
JA=31°C/W
Ambient Temperature
SCD55100/1/2/3/4
2-126
Electrical characteristics (over operating temperature) Parameter (Pwr Mode) digits dots/character Input current Input current (CLK I/O) (CLK I/O) Fext External Clock Input Frequency Fosc Internal Clock Input Frequency Clock Loading Clock Rise Time Clock Fall Time Digit -8.9 1086 Min. Typ. Max. Units °C/W VCC=4.5 VOH=2.4 VCC=4.5 VOH=0.4 VCC=5.0 CLKSEL=0 VCC=5.0 CLKSEL=1 VCC=5 inputs=0 VCC=5 displayed digits 100% brightness 25°C VCC=5 VIN=0 (all inputs) VCC=VIN=5.0 (all inputs) VCC=4.5 VCC=4.5 VCC=4.5 VOH=2.4 VCC=4.5 VOL=0.4 Conditions
Notes: Peak current Unused inputs must tied high. Contact Siemens volt operation. External oscillator must stopped being used maintain
Input/Output Circuits Figures show input output resistor/diode networks used protection eliminate substrate latch-up caused input voltage over/under shoot. Figure Inputs input
input/output
Figure Clock
SCD55100/1/2/3/4
2-127
Optical Characteristics 25°C (VCC=5.0 100% brightness level, viewing angle: axis 55°, axis 65°) SCD55100 Description Luminous Intensity Peak Wavelength Dominant Wavelength Yellow SCD55101 Description Luminous Intensity Peak Wavelength Dominant Wavelength High Efficiency SCD55102 Description Luminous Intensity Peak Wavelength Dominant Wavelength Green SCD55103 Description Luminous Intensity Peak Wavelength Dominant Wavelength High Efficiency Green SCD55104 Description Luminous Intensity Peak Wavelength Dominant Wavelength Symbol
(peak)
Symbol
(peak)
Min.
Typ.
Units µcd/dot
Symbol
(peak)
Min.
Typ.
Units µcd/dot
Symbol
(peak)
Min.
Typ.
Units µcd/dot
Symbol
(peak)
Min.
Typ.
Units µcd/dot
Min.
Typ.
Units µcd/dot
Notes: intensity matching 100% brightness 1.8:1. Displays binned intervals. Displays within given intensity category have intensity matching 1.5:1 (max.).
SCD55100/1/2/3/4
2-128
assignment Function SDCLK LOAD Function DATA CLKSEL
definitions Function SDCLK Definitions Loads data into 8-bit serial data register high transition. input enables data clocking into 8-bit serial shift register. When LOAD goes high, contents 8-bit serial Shift Register will decoded. connection connection connection Power supply/heat sink Power supply/heat sink connection connection connection Asynchronous input, when will clear Multiplex Counter, User Data Register. Control Word Register 100% brightness Address Register select Digit display blanked. Power supply ground Outputs master clock inputs external clock. H=internal clock, L=external clock connection connection Power supply/heat sink Power supply/heat sink Power supply/heat sink connection connection connection Serial data input Power supply ground
LOAD
Switching specifications (over operating temperature range VCC=4.5 Symbol TLDS TSDCLK TSDCW TLDH Description Reset Active Time Load Setup Time Data Setup Time Clock Period Clock Width Load Hold Time Data Hold Time Total Write Time Time Between Loads Min. Units
CLKSEL DATA
Note: TSDCW minimum time SDCLK high. SDCLK period must minimum
Figure matrix format
0.033 (0.84) typ. 0.080 (2.03) 0.011 (0.28) typ. 0.022 (0.56) typ. 0.145 (3.68)
Dimensions inches (mm) Dimensions inches (mm) Tolerance: .XXX=± .010 (.25)
TOLERANCE: .XXX=±.010 (.25)
SCD55100/1/2/3/4
2-129
Display column format
1=Display "On" 0=Display "Off'
Operation SCD5510X SCD5510X display consists CMOS containing control logic drivers eight characters. These components assembled compact mmx10 plastic package. Individual addressablity allows user great freedom creating special characters mini-icons. User Definable Character Examples illustrate different character symbol possibilities. serial data interface provides highly efficient interconnection between display mother board. SCD5510X requires only lines compared equivalent character parallel input part. on-board CMOS electronic heart display. accepts decoded serial data, which stored internal RAM. Asynchronously read character multiplexer strobe rate that results flicker free display. Figure shows three functional areas These include: input serial data register control logic, bits port RAM, internal multiplexer/display driver.
Column data ranges
Figure SCD5510X block diagram
Characters Decoder Driver
Column Logic Driver Clock RESET Oscillator Counter Chain Timing Logic Brightness Lamp Test Power Down
Serial Data Serial Data Clock OPCODE Load OPCODE Decode DATA Character Address Register WRITE Character/ Address Decode
Display Multiplexer
Bits
WRITE READ
Column Output
Control Word Address Register Software Clear
SCD55100/1/2/3/4
2-130
following explains format serial data loaded into display. user supplies string mapped decoded characters. contents this string shown Figure Figure shows that each character consist words. first word encodes display character location succeeding five bytes data. data represents status (On, Off) individual column LEDs. Figure shows that each word formatted include three Operational Code (OPCODE) defined bits D7-D5 five bits (D4-D0) representing Column Data, Character Address, Control Word Data. Figure shows sequence loading bytes data. Bringing LOAD line enables serial register accept data. shift action occurs high transition serial data clock (SDCLK). least significant (D0) loaded first. After eight clock pulses LOAD line brought high. With this transition OPCODE decoded. decoded OPCODE directs D4-D0 latched Character Address register, stored Column data, latched Control Word register. control requires minimum delay between successive byte loads. indicated Figure total clock cycles (60-8 words) required load characters into display. Figure Loading serial character data
Character Address Register bits, D4-D0 (Table Address Register bits, D7-D5 (Table direct Column Data bits, D4-D0 (Table specific location. Table shows Address example character "D." Column data written read asynchronously from RAM. Once loaded internal oscillator character multiplexer reads data from RAM. These characters strobed with column data shown Figures character strobe rate determined internal user supplied external Clock IC's counter. Table Character code Column Data
Example: Serial Clock MHz, Clock Period
Clock Cycles, 105.6
Character
Character
Character
Character
Character
Character
Character
Character
Character
Character
Clock Cycles, 13.2
Character Address
Column Data
Column Data
Column Data
Column Data
Column Data
Clock Cycles,
Clock Cycles,
Column Data Time Character Address Time OPCODE OPCODE Between Between Loads Loads ns(min.) ns(min.)
LOAD
Clock Period
Serial Clock
DATA
Time between LOADS
SCD55100/1/2/3/4
2-131
Table Load character address code Character Address Operation Load Character Character Character Character Character Character Character Character Character Character
Table Display brightness code Control Word Operation Level 100% 6.6%
Table Load column data code Column Data Operation Load
SCD5510X offers unique Display Power Down feature which reduces less than When FFHEX loaded, shown Table display brightness internal multiplex clock stopped. When Power Down mode data still written into RAM. display reactivated loading Brightness Level Control Word into display. Table Power down code Control Word Operation Level brightness
user activate four Control functions. These include: Brightness Level, Lamp Test, Power Down, Display Clear. OPCODEs five words used initiate these functions. OPCODEs Control Words Character Address Loading Column Data shown Tables user select seven specific brightness levels, Table These brightness levels percentages full brightness display) include: 100% HEX), (F1HEX), (F2HEX), (F3HEX), (F4HEX), (F5HEX), 6.6% (F6HEX). brightness levels controlled changing duty factor strobe pulse. Figure column location
Lamp Test enabled loading HEX, Table into serial shift register. This Control Word sets LEDs brightness level. Operation Lamp Test affect cleared loading Brightness Control Word. Table Lamp test code Control Word Operation Level Lamp Test (OFF) Lamp Test (ON)
Columns
Previously "on"
Software Clear (C0HEX), given Table clears Address Register RAM. display blanked Character Address Register will Character internal counter Control Word Register unaffected. Software Clear will remain active until next data input cycle initiated. Table Software clear code Control Word Operation Level CLEAR
SCD55100/1/2/3/4
2-132
Figure strobing
LOAD Columns LOAD Columns LOAD Columns LOAD Columns LOAD Columns LOAD
Multiplexer Display Driver characters multiplexed with resident column data. strobe rate established internal external Clock rate. Clock frequency divided counter chain. This results typical strobe rate pulling Clock line low, display operated from external Clock. external clock attached connection (pin 15). maximum external Clock frequency should limited MHz. asynchronous hardware Reset (pin also provided. Bringing this will clear Character Address Register, Control Word Register, RAM, blanks display. This action leaves display Character Address Brightness Level 100%. Electrical Mechanical Considerations Interconnect Considerations Optimum product performance when following electrical mechanical recommendations adopted. SCD5510X's constructed high speed CMOS process, consequently high speed noise SERIAL DATA, SERIAL DATA CLOCK, LOAD RESET lines cause incorrect data written into serial shift register. Adhere transmission line termination procedures when using fast line drivers long cables (>10 cm). Good digital grounds (pins power supply decoupling (pins will insure that (<400 peak) switching currents generate localized ground bounce. Therefore recommended that each display package capacitor between ground. When internal Clock being used connect CLKSEL VCC. those applications where RESET will connected system's reset control, recommended that this connected center node series 0.1, network. Thus upon initial power RESET will held allowing adequate time system power supply stabilize. SCD5510X allows power dissipation 1.29 power dissipation maximum operating temperature 85°C. Approximately this power dissipated board connection (pins 23). Optimum thermal reliability obtained connecting pins common located both sides board. This technique offers thermal resistance system ambient.
Protection input protection structure SCD55100/1/2/3/4 provides significant protection against damage. capable withstanding discharges greater than Take standard precautions, normal CMOS components. These include properly grounding personnel, tools, tables, transport carriers that come contact with unshielded parts. these conditions not, cannot met, keep leads device shorted together parts anti-static packaging. Soldering Considerations SCD55100/1/2/3/4 hand soldered with SN63 solder using grounded iron 260°C. Wave soldering also possible following these conditions: Preheat that does exceed 93°C solder side board package surface temperature 85°C. Water soluble organic acid flux (except carboxylic acid) resin-based flux without alcohol used. Wave temperature 245°C with dwell between sec. sec. Exposure wave should exceed temperatures above 260°C five seconds 0.063" below seating plane. packages should immersed wave. Post Solder Cleaning Procedures least offensive cleaning solution D.I. water (60°C) less than minutes. Addition mild saponifiers acceptable. commercial dishwasher detergents. faster cleaning, solvents used. Exercise care choosing solvents some chemically attack nylon package. Maximum exposure should exceed minutes elevated temperatures. Acceptable solvents (trichlorotrifluorethane), Trichloroethane, unheated acetone.(1)
Note: Acceptable commercial solvents are: Basic Arklone, Genesolv, Genesolv Blaco-Tron Blaco-Tron Freon
Unacceptable solvents contain alcohol, methanol, methylene chloride, ethanol, TP35, TCM, TMC, TMS+, TES. Since many commercial mixtures exist, contact solvent vendor chemical composition information. Some major solvent manufacturers are: Allied Chemical Corporation, Specialty Chemical Division, Morristown, Baron-Blakeslee, Chicago, Chemical, Midland, E.I. DuPont Nemours Co., Wilmington,
SCD55100/1/2/3/4
2-133
further information refer Appnotes current Siemens Optoelectronic Data Book. alternative soldering cleaning display modules sockets. Naturally, sockets .300" wide with .100" centers work well single displays. Multiple display assemblies best handled longer sockets sockets when available uniform package alignment. Socket manufacturers Aries Electronics, Inc., Frenchtown, Garry Manufacturing, Brunswick, Robinson-Nugent, Albany, Samtec Electronic Hardward, Albany, further information refer Appnote current Siemens Optoelectronic Data Book. Optical Considerations 0.145" high character SCD5510X gives readability eight feet. Proper filter selection enhances readability over this distance. Using filters emphasizes contrast ratio between character background. This will increase discrimination different characters. only limitation cost. Take into consideration ambient lighting environment best cost/benefit ratio filters. Incandescent (with almost green) fluorescent (with almost red) lights have flat spectral response sunlight. Plastic band-pass filters inexpensive effective strengthen contrast ratios. SCD5510/2 red/ high efficiency displays should matched with long wavelength pass filter range. SCD55103/4 should matched with yellow-green band-pass filter that peaks displays multiple colors, neutral density grey filters offer best compromise. Figure interface with Siemens/Intel 8031 microprocessor (using serial port mode
DATA
MASTER
DATA
2019 SLAVE
XTAL2
LOAD
LOAD
XTAL1 8031 P3.7 P3.3 P3.4
SCD55100/1/2/3/4
2-134
Additional contrast enhancement gained shading displays. Plastic band-pass filters with built-in louvers offer next step contrast improvement. Plastic filters improved further with anti-reflective coatings reduce glare. trade-off fuzzy characters. Mounting filters close display reduces this effect. Take care overheat plastic filter allowing proper flow. Optimal filter enhancements gained using circular polarized, anti-reflective, band-pass filters. circular polarizing further enhances contrast reducing light that travels through filter reflects back display less than Several filter manufacturers supply quality filter materials. Some them are: Panelgraphic Corporation, Caldwell, Homalite, Wilmington, Company, Visual Products Division, Paul, Polaroid Corporation, Polarizer Division, Cambridge, Marks Polarized Corporation, Deer Park, Hoya Optics, Inc., Fremont, last note mounting filters: recessing displays bezel assemblies inexpensive provide shading effect overhead lighting situations. Several Bezel manufacturers are: R.M.F. Products, Batavia, Nobex Components, Griffith Plastic Corp., Burlingame, Photo Chemical Products California, Santa Monica, I.E.E.-Atlas, Nuys,
Microprocessor Interface microprocessor interface through serial port, port eight data bits eight parallel port also control lines SDCLK LOAD. Power Sequence Upon power display will come random. Thus display should reset power-up. reset will Address Register Digit User (display blank) Control Word (100% brightness with Lamp Test off) internal counters reset.
Figure SCD5510X interface with Siemens/Intel 8031 microprocessor
DATA
MASTER
DATA
SLAVE
P3.0 XTAL2 P3.1 P3.6 XTAL1 P1.0 P0.0
LOAD
LOAD
8031
SCD55100/1/2/3/4
2-135
Figure SCD5510X interface with Motorola 68HC05C4 microprocessor (using port)
DATA
MASTER
DATA
SLAVE
OSC1 SCLK MOSI
LOAD
LOAD
OSC2
68HC05C4
Cascading Multiple Displays Multiple displays cascaded using pins shown below. display designated Master Clock source should have tied high slaves should have their pins tied low. pins should tied together. display drive slave I/Os. synchronize display counters. Figure Cascading multiple displays
DATA DATA SDCLK Chip Address Decoder
Address Decode 1-14
SDCLK
LOAD
Intelligent Display
more displays between
LOAD
Intelligent Display DATA SDCLK
SCD55100/1/2/3/4
2-136
Loading Data Into Display following procedure load data into display: Power display. Bring (600 duration minimum) clear Multiplex Counter, Address Register, Control Word Register, User Data Register. display will blank. Display brightness 100%. different brightness desired, load proper brightness opcode into Control Word Register. Load Digit Address into display. Load display column data selected digit. Repeat steps digits. Data contents word "Displays"
Step (optional) Function CLEAR BRIGHTNESS SELECT DIGIT SELECT DIGIT SELECT DIGIT SELECT DIGIT SELECT DIGIT SELECT DIGIT SELECT DIGIT SELECT DIGIT SELECT
Note: display already reset Power there need Software Clear.
SCD55100/1/2/3/4
2-137
User Definable Character Examples* Upper lower case alphabets
CODE CODE CODE CODE CODE CODE CODE CODE CODE
Numerals punctuation
CODE CODE CODE CODE CODE CODE CODE CODE CODE
*CAUTION: more than LEDs "on" time 100% brightness.
SCD55100/1/2/3/4
2-138
User Definable Character Examples* (continued) Scientific notations, etc.
CODE CODE CODE CODE CODE CODE CODE CODE CODE
Foreign characters
CODE CODE CODE CODE CODE CODE CODE CODE CODE
*CAUTION: more than LEDs "on" time 100% brightness.
SCD55100/1/2/3/4
2-139

STANDARD Slimline 0.145" 10-Character Matrix Serial Input Ad

Top Searches for this datasheet

Other recent searches