INCH IMAGE SENSOR CERDIP KC73129UC interline transfer area i

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

INCH IMAGE SENSOR CERDIP KC73129UC interline transfer area i

Datasheet Thumbnail

Top Searches for this datasheet

KC73129UC
INCH IMAGE SENSOR
CERDIP
KC73129UC interline transfer area image sensor developed 1/3inch optical format video cameras, surveillance cameras, object detectors image pattern recognizers. High sensitivity achieved through adoption complementary color mosaic filters, on-chip micro lenses This chip features field integration read system electronic shutter with variable charge storage time.
FEATURES
High Sensitivity Optical Size 1/3inch Format On-chip Complementary Color Mosaic Filter Variable Speed Electronic Shutter Dark Current Horizontal Register Drive 16pin Ceramic Package Field Integration Read System
ORDERING INFORMATION
Device KC73129UC Package 16pin CERDIP Operating Temperature -10°C 50°C
STRUCTURE
Number total pixels Number effective pixels Chip size Unit pixel size Optical blacks dummies 6.00mm(H) 4.95mm(V) 9.80µm(H) 6.30µm(V) Refer from below figure
Dummy Pixels
Effective Imaging Area Optical Black Pixels Effective Pixels V-CCD OUTPUT H-CCD
KC73129UC
BLOCK DIAGRAM
INCH IMAGE SENSOR
VERTICAL SHIFT REGISTER
VERTICAL SHIFT REGISTER
VERTICAL SHIFT REGISTER
VERTICAL SHIFT REGISTER
HORIZONTAL SHIFT REGISTER
DESCRIPTION
Symbol
VOUT
Description
Vertical Transfer Clock Vertical Transfer Clock Vertical Transfer Clock Vertical Transfer Clock Ground Output Stage Gate Bias Output Stage Source Bias Signal Output
Symbol
Description
Output Stage Drain Bias Ground Substrate Bias Protection Circuit Bias Charge Reset Clock Connection Horizontal Transfer Clock Horizontal Transfer Clock
KC73129UC
ABSOLUTE MAXIMUM RATINGS
Characteristics Substrate Voltage Supply Voltage Vertical Clock Input Voltage Horizontal Clock Voltage Difference between Vertical Horizontal Clock Input Pins Output Clock Protection Circuit Bias Voltage Operating Temperature Storage Temperature
INCH IMAGE SENSOR
*(1)
Symbols SUB-GND VDD,VOUT,VSS-GND V1,V2,V3,V4-GND V1,V2,V3,V4-VL H1,H2 V1,V2,V3,V4 H1,H2 H1,H2 RG,VGG TOPR TSTG
Min. -0.3 -0.3 -0.3 -0.3 -0.3
Max.
Unit
device destroyed, applied voltage temperature higher than absolute maximum rating voltage temperature.
CONDITIONS
Item
Output Stage Drain Bias Output Stage Gate Voltage Output Stage Source Voltage Substrate Voltage Adjustment Range Fluctuation Voltage Range after Substrate Voltage Adjusted Reset Gate Voltage Adjustment Range Fluctuation Voltage Range after Reset Gate Voltage Adjusted Protection Circuit Bias Voltage Output Stage Drain Current
Symbol
VSUB VSUB VRGL VRGL
Min.
Typ.
Max.
Unit
Remark
14.55 15.0 15.45 1.75 2.25 Ground through 19.0
voltage vertical clock waveform
CLOCK VOLTAGE CONDITIONS
Item
Read-out Clock Voltage Vertical Transfer Clock Voltage Horizontal Transfer Clock Voltage Charge Reset Clock Voltage Substrate Clock Voltage
Symbol
VVH1~VVH4 VVL1~VVL4 VRGLH -VRGLL VSUB
Min.
14.55 -0.05 -9.0 4.75 -0.05 4.75 20.0
Typ.
15.0 -8.5 23.5
Max.
15.45 0.05 -8.0 5.25 0.05 5.25 25.0
Unit
Remark
High level VVH=(VVH1+VVH2)/2 VVL=(VVL3+VVL4)/2 High High Shutter
KC73129UC
INCH IMAGE SENSOR
DRIVE CLOCK WAVEFORM CONDITIONS
Read clock waveform
100%
Vertical transfer clock waveform
VVHH VVHL VVH3 VVHL
VVHH
VVL1 VVLH VVLL
VVL3 VVLL
VVLH
VVHH VVHH VVHL
VVHH
VVHH
VVH2
VVHL
VVHL
VVH4
VVHL
VVL2 VVLL
VVLH VVLL
VVLH
VVL4
KC73129UC
INCH IMAGE SENSOR
Horizontal transfer clock waveform diagram
Reset gate clock waveform diagram
VRGH
Point waveform
VRGL 0.5V VRGL
VRGLH VRGLL
waveform
VRGLH maximum value VRGLL minimum value coupling waveform period from Point diagram about rise VRGL=(VRGLH+VRGLL)/2 VRG=VRGH-VRGL
Substrate clock waveform
100%
VSUB
VSUB
KC73129UC
INCH IMAGE SENSOR
CLOCK EQUIVALENT CIRCUIT CONSTANT
Item
Capacitance between Vertical Transfer Clock Capacitance between Vertical Transfer Clocks
Symbol
CV1, CV2, CV12, CV34 CV23, CV41 CV13 CV24 CH1, CH12 CSUB RGND RH1,
Typ.
1,300 1,300 1120
Unit
Remark
Capacitance between Horizontal Transfer Clock Capacitance between Horizontal Transfer Clocks Capacitance between Reset Gate Clock Capacitance between Substrate Clock Vertical Transfer Clock Serial Resistor Vertical Transfer Clock Ground Resistor Horizontal Transfer Clock Serial Resistor Reset Gate Clock Serial Resistor
CV24
CV13 RGND
CV23
KC73129UC
INCH IMAGE SENSOR
25°C) Typ. 0.015 1,000 Max. Unit mV/lux times Test method Remark
IMAGE SENSOR CHARACTERISTICS
Item Sensitivity Saturation Signal Smear Blooming Margin Uniformity Dark Signal Flicker Flicker Red, Blue Color Uniformity Line Stripe W,R,G,B Symbol YSAT FCR,FCB DSR,DSB LCW,LCR, LCG,LCB Min.
50°C
TESTING SYSTEM
SIGNAL OUTPUT
(3dB down 4MHz) LPF1 ILLUMINANCE SIGNAL OUTPUT
C.D.S
LPF2 (3dB down 1MHz) CHROMA SIGNAL OUTPUT
NOTE) Adjust gain that total gains between between equal
KC73129UC
TEST CONDITION
INCH IMAGE SENSOR
light source with color temperature 3,200K CM-500S filter. light source adjusted accordance with average value signals indicated each item. Through following tests substrate voltage reset gate clock value bias condition while device condition typical value bias clock conditions. Through following tests, defects excluded unless otherwise specified optical black level hence forth referred reference output signal which taken signal output chroma signal output test system.
COLOR FILTER ARRAY
color filter array this image sensor shown right figure. this complementary mosaic used with operation field integration mode, where photosensors read during each video field. signals from vertically-adjacent photosensor lines, such line couple field summed when signal charges transferred into vertical transfer column. read line pairing shifted down line field sensor output signals through horizontal register (H-CCD) line [G+Cy], [MG+Ye], [G+CY], [Mg+Ye]. These signals processed order compose signals. adding adjacent signals line signal formed follows.
Ye)]
H-CCD
Color coding Diagram
signal composed substracting adjacent signals line
[(Mg
Next, signals through H-CCD line [Mg+Cy], [G+Ye], [Mg+Cy], [G+Ye]. Simmilary, signals composed line follows
-(2B
Accordingly, signal balanced relation scanning lines, signa takes form -(B-Y) alternate lines. same field.
KC73129UC
TEST METHODS
INCH IMAGE SENSOR
Measure light intensities(L) when averaged illuminance output value(Y) standard illuminance output value, 150mV(YA) when half 150mV(1/2 YA).
L1YA
Adjust light intensity times that signal output average value 150mV) then test signal minimum value (Y=YSAT). Adjust light intensity times that signal output average value 150mV), then remove read-out clock drain signal photosensors electronic shutter operation respective horizontal blanking times with other clocks unchanged. Measure maximum illuminance output value (YSM).
100(%)
Adjust light intensity 1000 times that signal output average value 150mV), Then confirm that Blooming dose appear.
Measure maximum minimum illuminance output value (YMAX, YMIN) when light intensity adjusted make (YMAX YMIN) 100.
Measure signal output average value YD[mV] with horizontal idling time transfer level reference, when device ambient temperature 50°C light sources shielded. Adjust light intensity make Y=YA. Measure difference value (YF) between averaged illuminance signal values even fields.
Adjust light intensity make Y=YA.Then insert blue optical filters respectively, measure differences (CR, between chroma signal values even fields signal output averag value (CR, CB).
100(%)
where
Adjust light intensity make Y=YA. Then test maximum(CR,MAXand CB,MAX) minimum(CR,MIN CB,MIN) values chroma signals from channels.
,MAX ,MIN
100(%) where
Adjust light intensity make 150mV(YL). Then insert white filter, red(R), green(G) blue(B) optical filters respectively, measure illuminance signal difference values (YLW, YLR, YLG, YLB) between illuminance signal lines same field.
100(%)
where
KC73129UC
INCH IMAGE SENSOR
SPECTRAL RESPONSE CHARACTERISTICS
Excluding light source characteristics
NORMALIZED RESPONSE
Yellow
Cyan Green
Magenta
WAVE LENGTH(nm)
KC73129UC
APPLICATION CIRCUITS
INCH IMAGE SENSOR
22µH XSUB 10µF/10V 10µF/10V
KS7221D
100k
MA110
22µF/20V
22µH
47µF/10V 1µF/10V 180k
VOUT
KC73129UC
0.01
KSC2757 4.7k 3.9K MA110 0.47µF/50V 100k KSC1523 3.0µF/25V 10µF/25V 22µH 22µH 10µF/25V
OUTPUT
KC73129UC
INCH IMAGE SENSOR
READ-OUT CLOCK TIMING CHART
Unit
FIELD
38.1
EVEN FIELD
KC73129UC
INCH IMAGE SENSOR
CLOCK TIMING CHART (VERTICAL SYNC.)
CLP1
CLOCK TIMING CHART (HORIZONTAL SYNC.)
XSHP XSHD CLP1 (During electronic shutter operation)
KC73129UC
PACKAGE DIMENSIONS
INCH IMAGE SENSOR
(Unit=mm)
Center effective imaging area/ Center package
6.1+0.15
t=0.25+0.02
5.7+0.15
8.20+0.10 10.00+0.10
2.50 2-R0.50
11.40+0.15
7.20+0.10 9.20+0.15 12.20+0.15
Rotation error =1.5
1.10+0.08
2.80+0.30
1.27+0.25 4.13
0.30+0.10 1.27+0.05 1.27x7=8.89+0.10 11.60+0.12
0.46+0.10
Optical center deviation from mechanical center ±0.15mm direction. Optical surface height from glass surface 1.1±0.15mm Optical surface height from package backside bottom 1.7±0.10mm
KC73129UC
HANDLING INSTRUCTION
INCH IMAGE SENSOR
Static charge prevention image sensors easily damaged static discharge. Before handling besure take following protective measures. Either handle bare handed chargeable gloves, clothes material. Also conductive shoes. When handling directly, earth band. Install conductive floor working table prevent generation static electricity. Ionized recommended discharging when handling image sensor. shipment mounted substrates, boxes treated prevention static charges. Soldering Make sure package temperature does exceed 80°C Solder dipping mounting furnace causes damage glass other defects. grounded soldering iron solder each less than seconds. repairs remount, cool sufficiently. dismount imaging device, solder suction equipment. When using electronic disoldering tool, thermal controler zero cross On/Off type connect ground Dust Dirt protection Operate clean environments (around class 1000 will appropriate). either touch glass plates hand have object come contact with glass surface. Should dirt stick glass surface blow with blow (for dirt stuck through static electricity ionized recommended). Clean with cotton ethyl alcohol glass surface grease stained. carful scratch glass. Keep case protect from dust dirt. prevent condensation, preheat precool when moving room whith great temperature differences. When protective tape applied before shipping, just before remove tape applied electrostatic protection. reuse tape.
expose strong light (sun rays) long period, color filter discolored Exposure high temperatures humidity will affect characteristics. Accordingly avoid storage usage such conditions. image sensors precise optical equipment that should subject mechanical shocks.

INCH IMAGE SENSOR CERDIP KC73129UC interline transfer area i

Top Searches for this datasheet

Other recent searches