NL7WB66 very dual SPST analog switch. (Typ) device offered very popula

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

NL7WB66 very dual SPST analog switch. (Typ) device offered very popula

Datasheet Thumbnail

Top Searches for this datasheet

NL7WB66 Ultra-Small SPST Analog Switch
NL7WB66 very dual SPST analog switch. (Typ) device offered very popular cost package. designed general purpose dual switch used switch either analog signals such audio video digital signal such TTL, CMOS, LVDS, ECL, complex digital signals such QPSK.
MARKING DIAGRAM
SUFFIX CASE
Excellent Performance RDSON High Speed Operation: 0.25 (Max) 1.65 Operating Range Reduced Threshold Voltages LVTTL Control Eliminates Need Translators Many Applications Compatibility when Operate with Inputs, Also Meets Full CMOS Specifications Ultra-Low Charge Injection Stand-by Power (Max) 25°C Control Pins IN1, IN2, Overvoltage Tolerant Replacement TC7WB66, NC7WB66, 74LVC2G66 Protection: Machine Model >200 Human Body Model >2000 Latchup Rating: Pb-Free Package Available
Device Code Date Code* Pb-Free Package
(Note: Microdot either location) *Date Code orientation vary depending upon manufacturing location.
ASSIGNMENT
Function COM1 COM2
Typical Applications
Cell Phones PDAs Digital Still Cameras Video Digital Video
COM1
FUNCTION TABLE
On/Off Enable Input State Analog Switch
COM2
Figure Assignment Diagram
ORDERING INFORMATION
detailed ordering shipping information package dimensions section page this data sheet.
Semiconductor Components Industries, LLC, 2005
August, 2005 Rev.
Publication Order Number: NL7WB66/D
NL7WB66
MAXIMUM RATINGS
Symbol IGND TSTG VESD Supply Voltage Input Voltage Output Voltage Input Diode Current Output Diode Current Output Sink Current Supply Current Supply Ground Current Ground Storage Temperature Range Lead Temperature, from Case Seconds Junction Temperature under Bias Thermal Resistance Power Dissipation Still 85°C Moisture Sensitivity Flammability Rating Withstand Voltage Oxygen Index: Human Body Model (Note Machine Model (Note Charged Device Model (Note Rating Value *0.5 )7.0 *0.5 )7.0 *0.5 )7.0 $100 $100 )150 )150 Level 0.125 2000 Unit °C/W
Maximum ratings those values beyond which device damage occur. Maximum ratings applied device individual stress limit values (not normal operating conditions) valid simultaneously. these limits exceeded, device functional operation implied, damage occur reliability affected. Measured with minimum spacing board, using mm-by-1 inch, 2-ounce copper trace with flow. Tested EIA/JESD22-A114-A. Tested EIA/JESD22-A115-A. Tested JESD22-C101-A.
RECOMMENDED OPERATING CONDITIONS
Symbol Positive Supply Voltage Digital Input Voltage (Enable) Static Dynamic Voltage Across Switch Analog Input Voltage Operating Temperature Range, Package Types Input Rise Fall Time (Enable Input) Characteristics 1.65 +125 Unit ns/V
http://onsemi.com
NL7WB66
DEVICE JUNCTION TEMPERATURE TIME 0.1% BOND FAILURES
Junction Temperature Time, Hours 1,032,200 419,300 178,700 79,600 37,000 17,800 8,900 Time, Years 117.8 47.9 20.4
NORMALIZED FAILURE RATE
FAILURE RATE PLASTIC CERAMIC UNTIL INTERMETALLICS OCCUR 130°C 120°C 100°C 110°C 90°C 80°C TIME, YEARS
1000
Figure Failure Rate Time Junction Temperature
CHARACTERISTICS Digital Section (Voltages Referenced GND)
Guaranteed Limit Symbol Parameter High-level Input Voltage, Control Input Condition 1.65 1.95 1.65 1.95 Enable 255C 0.65 0.35 +0.1 855C 0.65 0.35 +1.0 <1255C 0.65 0.35 +1.0 Unit
Low-level Input Voltage, Control Input
Maximum Input Leakage Current, Enable Inputs Maximum Quiescent Supply Current (per package)
http://onsemi.com
NL7WB66
ELECTRICAL CHARACTERISTICS Analog Section
Guaranteed Limit Symbol Parameter On-State Switch Resistance Condition 1.65 1.65 1.65 1.65 1.65 255C 855C <1255C Unit
RON(p)
Peak On-State Resistance
GND, GND,
Difference On-State Resistance between Switches
RFLAT
INO(OFF)
Leakage Current
VCOM VCOM VCOM
ICOM(OFF)
Leakage Current
ELECTRICAL CHARACTERISTICS (Input
Guaranteed Limit $0.15 Symbol tOFF Parameter Output Enable Time Output Disable Time Propagation Delay Time Test Conditions 10.5 0.55 $0.2 $0.3 0.35 $0.5 0.25 Unit
Typical 255C, CNO1 CNO2 CCOM(OFF) CCOM(ON) Maximum Input Capacitance, Select Input Analog (Switch Off) Common (Switch Off) Feed-through (Switch Off)
Unit
http://onsemi.com
NL7WB66
ADDITIONAL APPLICATIONS CHARACTERISTICS (Voltage Reference Unless Noted)
Symbol Parameter Maximum On-Channel -3.0 Bandwidth Minimum Frequency Response Maximum Feed-Through Loss Condition centered between centered between centered between GND, kHz, Rgen Sine Wave Sine Wave Typical 255C -2.2 -0.8 -0.4 0.19 0.06 Unit
VONL
VISO
Off-Channel Isolation
Charge Injection Enable Input Common Total Harmonic Distortion Noise
DEVICE ORDERING INFORMATION
Device Nomenclature Device Order Number NL7WB66 NL7WB66G Circuit Indicator Technology Device Function 2066 2066 Package Suffix Package Type (Pb-Free) Tape Reel Size 3000 Units Tape Reel 3000 Units Tape Reel
information tape reel specifications, including part orientation tape sizes, please refer Tape Reel Packaging Specifications Brochure, BRD8011/D.
http://onsemi.com
NL7WB66
TIMING INFORMATION
VOUT Output Input
Input
Figure tON/tOFF
tOFF
VOUT Input
Output
Input
Figure tON/tOFF
tOFF
Reference
Transmitted
Generator Channel switch control/s test socket normalized. isolation measured across channel. loss bandwidth switch. VISO, Bandwidth VONL independent input signal direction. VOUT VISO Channel Isolation VOUT VONL Channel Loss Bandwidth (BW) frequency below VONL
Figure Channel Isolation/On Channel Loss (BW)/Crosstalk Channel Channel)/VONL
Output DVOUT
Figure Charge Injection:
http://onsemi.com
NL7WB66
PACKAGE DIMENSIONS
SUFFIX CASE 493-02 ISSUE
DETAIL
NOTES: DIMENSIONING TOLERANCING ANSI Y14.5M, 1982. CONTROLLING DIMENSION: MILLIMETERS. DIMENSION DOES INCLUDE MOLD FLASH, PROTRUSION GATE BURR. MOLD FLASH. PROTRUSION GATE BURR SHALL EXCEED 0.140 (0.0055") SIDE. DIMENSION DOES INCLUDE INTER-LEAD FLASH PROTRUSION. INTER-LEAD FLASH PROTRUSION SHALL E3XCEED 0.140 (0.0055") SIDE. LEAD FINISH SOLDER PLATING WITH THICKNESS 0.0076-0.0203 (300-800 TOLERANCE UNLESS OTHERWISE SPECIFIED ±0.0508 (0.0002 MILLIMETERS 1.90 2.10 2.20 2.40 0.60 0.90 0.17 0.25 0.20 0.35 0.50 0.40 0.10 0.18 0.00 0.10 3.00 3.20 0.23 0.34 0.23 0.33 0.37 0.47 0.60 0.80 0.12 INCHES 0.075 0.083 0.087 0.094 0.024 0.035 0.007 0.010 0.008 0.014 0.020 0.016 0.004 0.007 0.000 0.004 0.118 0.126 0.010 0.013 0.009 0.013 0.015 0.019 0.024 0.031 0.005
SEATING PLANE
0.10 (0.004)
0.10 (0.004)
0.10
DETAIL
SOLDERING FOOTPRINT*
0.38 0.015 0.50 0.0197 0.07 0.30 0.012 0.0394
SCALE inches
*For additional information Pb-Free strategy soldering details, please download Semiconductor Soldering Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
NL7WB66
Semiconductor registered trademarks Semiconductor Components Industries, (SCILLC). SCILLC reserves right make changes without further notice products herein. SCILLC makes warranty, representation guarantee regarding suitability products particular purpose, does SCILLC assume liability arising application product circuit, specifically disclaims liability, including without limitation special, consequential incidental damages. "Typical" parameters which provided SCILLC data sheets and/or specifications vary different applications actual performance vary over time. operating parameters, including "Typicals" must validated each customer application customer's technical experts. SCILLC does convey license under patent rights rights others. SCILLC products designed, intended, authorized components systems intended surgical implant into body, other applications intended support sustain life, other application which failure SCILLC product could create situation where personal injury death occur. Should Buyer purchase SCILLC products such unintended unauthorized application, Buyer shall indemnify hold SCILLC officers, employees, subsidiaries, affiliates, distributors harmless against claims, costs, damages, expenses, reasonable attorney fees arising directly indirectly, claim personal injury death associated with such unintended unauthorized use, even such claim alleges that SCILLC negligent regarding design manufacture part. SCILLC Equal Opportunity/Affirmative Action Employer. This literature subject applicable copyright laws resale manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT: American Technical Support: 800-282-9855 Toll Free Literature Distribution Center Semiconductor USA/Canada P.O. 61312, Phoenix, Arizona 85082-1312 Phone: 480-829-7710 800-344-3860 Toll Free USA/Canada Japan: Semiconductor, Japan Customer Focus Center 2-9-1 Kamimeguro, Meguro-ku, Tokyo, Japan 153-0051 Fax: 480-829-7709 800-344-3867 Toll Free USA/Canada Phone: 81-3-5773-3850 Email: orderlit@onsemi.com Semiconductor Website: http://onsemi.com Order Literature: http://www.onsemi.com/litorder additional information, please contact your local Sales Representative.
http://onsemi.com
NL7WB66/D

NL7WB66 very dual SPST analog switch. (Typ) device offered very popula

Top Searches for this datasheet

Other recent searches