This documentation written October 2003. This third series three Progr

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

This documentation written October 2003. This third series three Progr

Datasheet Thumbnail

Top Searches for this datasheet

K150. PROGRAMMER
This documentation written October 2003. This third series three Programmers designed Tony Nixon. Most components resistors, some capacitors, transistors surface mount presoldered board. There through-hole components buyer solder. Color photos assembled found photos with optional socket. Hardware. Most components resistors, transistors already presoldered onto PCB. some thru-hole components have been left buyer solder. Solder lowest height thru-hole components first. Make sure crystal mounted 2-3mm above case cannot make contact with pads layer resistor. connector type. will need standard cable connect from your K150. Software. Download diypack14.zip from Unzip setup.exe. creates unloads c:\diypgmrg. programmed firmware this contains k150.hex file which folder. NOTE: onto this site find later version diypack.zip then make sure download diypack14.zip latest version. After have working then download latest version, upgrade firmware with latest MicroPro.exe. Drivers. will need download install drivers from http://www/ftdichip.com these drivers being updated about every month. this time they found heading
Drivers Win'98 2000 with enhanced series support
COM3 when MicroPro first runs must Port (File/Port.) Change. reality that drivers, K150 firmware K150 User Interface software MicroPro.exe being upgraded almost every month PICs added improvements made. latest information look COMPONENTS 1N4004 1N4148 6.000mHz 49/US package 7812 7805 10uF/25V ecap 47uF/25V ecap Power jack green Rubber feet header harness socket programmed PIC16F628-20P socket K150 with surface mount components have provided socket with this kit. However, going doing programming really need socket. direct from $US15 including airmail postage. Protocol Number. help match hardware firmware there protocol number each. they same (P00A) this case then software firmware matched. This should stop problems with matching firmware with MicroPro versions past. (Protocol number called Build number diypack12 changed it.) Other Programmer Kits. 149B allows both serial port input. Only FT232BM chip surface mounted (and presoldered.) other components thru-hole. all-Flash Programmer powered just port. Almost surface mount with some thru-hole components. Programmers supported MicroPro software. Problems. Email peter@kitsrus.com
recently downloaded P9012134.zip, unpacked into C:\diypgmrd\USB then Start/Settings/Control Panel/Add Hardware. (diypgmrd folder created diypack10.zip.) Disregard Microsoft Uncertified Driver warning. download Help file AN232-05 from guide through driver installation unsure find port number driver going DeviceManager/Ports (COM&LPT). system
IN4004
7812
Vout
BC856B
Vout
BC856B
BC856B
VccP VPP1
SKT1 PROGRAMMER
VPP2 VccP VccP VPP2 DATA CLOCK VccP DATA CLOCK VccP DATA CLOCK VccP CLOCK DATA
VccP
16VDC
7805
IN4148 100N 100N
VPP1
VPP2
47uF
10uF
SVP1 SVP2
74LS06
VccP CLOCK DATA VPP1
470R 100N
USBP USBM USBP USBM AVCC
100N FT232BM
ISCP
MCLR MCLR OSC1 OSC2 MCLR XTAL DATA CLOCK VccP
USBDP USBDM 3V3OUT XTIN XTOUT TEST RESET# EECS EESK EEDATA RSTOUT# AGND
XTAL
RTS# CTS# DTR# DSR# DCD#
6MHz
TXDEN PWREN# PWRCTL TXLED# RXLED# SLEEP# SVP1 SVP2
16F628
Title Size Number 20-Aug-2003 E:\PROGRAM\SCHEMS\K150.SCH Sheet Drawn Revision
7406 7406
Date: File:
7406

Other recent searches