IPS7071GPbF PROTECTED HIGH SIDE SWITCH Over temperature shut
|
|
|
Top Searches for this datasheet
Data sheet PD60309
IPS7071GPbF
PROTECTED HIGH SIDE SWITCH
Over temperature shutdown (with auto-restart) Short circuit protection (current limit) Active clamp Open load detection Logic ground isolated from power ground protection Ground loss protection Status feedback
Product Summary Rds(on) Vclamp Limit Open load Package 110m max.
Description
IPS7071GPbF fully protected five terminal high side switch with built short circuit, over-temperature, protection, inductive load capability diagnostic feedback. output current limited Ilim value. Current limitation activated until thermal protection acts. over-temperature protection turns device junction temperature exceeds Tshutdown. will automatically restart after junction cooled below Tshutdown. diagnostic provided status feedback short circuit, over-temperature open load detection. double level shifter circuitry allows large offsets between logic ground load.
IPS7071GPbF
Typical Connection
+Bat Control Diag Input Signal Load Pull-up resistor Open Load detection
www.irf.com
IPS7071GPbF
Absolute Maximum Ratings
Absolute maximum ratings indicate sustained limits beyond which damage device occur. voltage parameters referenced Ground lead. (Tambient=25°C unless otherwise specified).
Symbol
Vout Voffset max. cont. max. max. cont. ESD1 ESD2 max.
Parameter
Maximum output voltage Maximum logic ground load ground offset Maximum input voltage Maximum voltage Maximum continuous voltage Maximum current Maximum diagnostic output current Maximum diagnostic output voltage Maximum power dissipation (internally limited thermal protection) Rth=100°C/W Maximum continuous diode current (Rth=100°C/W) Electrostatic discharge voltage (Human body) 100pF, 1500 Electrostatic discharge voltage (Machine Model) C=200pF,R=0,L=10µH Max. storage operating temperature junction temperature
Min.
Max.
Units
Vcc-65 Vcc+0.3 Vcc-65 Vcc+0.3 -0.3 -0.3
1.25 +150
Thermal Characteristics
Symbol
Rth1
Parameter
Thermal resistance junction ambient IPS7071G
Typ.
Max.
Units
°C/W
Recommended Operating Conditions
These values given quick design. operation outside these conditions, please consult application notes.
Symbol
Iout Rdgs
Parameter
High level input voltage level input voltage Continuous drain current, Tamb=85°C, Tj=125°C, Vin=5V, Rth=100°C/W Recommended resistor series with Recommended resistor series with Recommended pull-up resistor open load detection
Min.
-0.3
Max.
Units
www.irf.com
IPS7071GPbF
Static Electrical Characteristics
Tj=25°C, Vcc=14V (unless otherwise specified)
Symbol
Parameter
Min.
Typ.
Max.
Units
Test Conditions
Vin=5V, Iout=2.5A Vin=5V, Iout=2.5A Vin=5V, Iout=2.5A Iout=10mA (see Fig. Iout=1A (see Fig. Iout= 2.5A Vin=0V, Vout=0V Vin=5V Vout=0V Vout=6V Vdg=5.5V Idg=1.6mA
state resistance Tj=25°C Rds(on) state resistance Tj=150°C state resistance Tj=25°C, Vcc=6.5V Operating voltage range clamp clamp voltage clamp clamp voltage Body diode forward voltage Supply current when Supply current when Iout@0V Output leakage current Iout@6V Output leakage current leakage Diagnostic output leakage current Vdgl level diagnostic output voltage Input high threshold voltage Input threshold voltage Input hysteresis high Under voltage high threshold voltage Under voltage threshold voltage Undervoltage hysteresis Input current when device Guaranteed design
1.35
0.15
Vin=5V
Switching Electrical Characteristics
Vcc=14V, Resistive load=14, Vin=5V, Tj=25°C
Symbol
Tdon dV/dt (On) Tdoff dV/dt (Off) EOff Tdiag
Parameter
Turn-on delay time Rise time Vout=Vcc-5V Rise time Vout=0.9 Turn dV/dt Turn energy Turn-off delay time Fall time Vout=0.1 Turn dV/dt Turn energy Vout Vdiag propagation delay
Min.
Typ.
Max.
Units
V/µs V/µs
Test Conditions
Fig.
Fig. Fig.
www.irf.com
IPS7071GPbF
Protection Characteristics
Symbol Parameter Min.
150(2)
Typ.
Max.
Units
Test Conditions
Vout=0V Fig.
Ilim Internal current limit Tsd+ Over temperature high threshold TsdOver temperature threshold Short-circuit detection voltage(3) Vopen load Open load detection threshold Guaranteed design Reference
Truth Table
Operating Conditions
Normal Normal Open Load Open Load Short circuit (limiting) Short circuit Over-temperature (cycling) Over-temperature With pull-up resistor connected between output Vcc.
Lead Assignments
8765
1234
5-6-7-8
www.irf.com
IPS7071GPbF
Functional Block Diagram
values typical
165°C
158°C Vcc-Gnd 2.5V Level Shifter
Charge Pump
Driver
150k
2.0V Sense Limit
Loss Protection
Open Load
Short Circuit
www.irf.com
IPS7071GPbF
clamp
Iout
limiting Thermal cycling
Ilim
clamp
Tsd+ Tsd-
Application Notes evaluate power dissipation
Figure Active clamp waveforms
Figure Protection timing diagram
Vout
Vcc-5V
Vout
Blanking Diag Tdiag
Blanking Diag
Figure Switching times definition
Figure Diagnostic delay definition
www.irf.com
IPS7071GPbF
Vclamp Iout, Output current
Vout
During active clamp, Vload negative
Iout
1E+2 1E+3 1E+4 1E+5 1E+6
Load inductance (µH)
Figure Active clamp test circuit Figure Max. Output current Load inductance (µH)
100.0
Ids, cont. Output current
Zth, transient thermal impedance (°C/W)
10.0
0.0001 0.001
0.01
Tamb, Ambient temperature (°C)
Figure Max. ouput current Ambient temperature (°C)
Time
Figure Transient thermal impedance (°C/W) time
www.irf.com
IPS7071GPbF
Eon, Eoff, switching energy (µJ)
Eoff
limit
junction temperature (°C)
Figure limit junction temperature (°C)
Iout, Output current
Figure Switching energy (µJ) Output current
200%
Rds(on), Drain-to-Source Resistance (Normalized)
Blanking time (µs)
150%
Tdiag Tdiag
100%
junction temperature (°C)
Figure Normalized Rds(on) (°C)
Output current
Figure Diagnosis Blanking time (µs) Output current
www.irf.com
IPS7071GPbF
1.E+4
1.E+4
off, supply current (µA)
off, supply current (µA)
1.E+3
1.E+3
1.E+2
1.E+2
1.E+1
1.E+1
1.E+0
1.E+0
Vcc, power supply voltage
Figure (µA)
junction temperature (°C)
Figure (µA) (°C)
www.irf.com
IPS7071GPbF
Case Outline
www.irf.com
IPS7071GPbF
Tape Reel
WORLD HEADQUARTERS: Kansas St., Segundo, California 90245 Tel: (310) 252-7105 Data specifications subject change without notice MSL2 qualified This product been designed qualified Automotive [Q100] market. 6/24/2007
www.irf.com
Other recent searches
ST24E64 - ST24E64 ST24E64 Datasheet
ST25E64 - ST25E64 ST25E64 Datasheet
R5F3640DDFA - R5F3640DDFA R5F3640DDFA Datasheet
PI403636 - PI403636 PI403636 Datasheet
LT1949-1 - LT1949-1 LT1949-1 Datasheet
LA7848 - LA7848 LA7848 Datasheet
LA7848BUSICCRT - LA7848BUSICCRT LA7848BUSICCRT Datasheet
AN8071 - AN8071 AN8071 Datasheet
AMMC-6440 - AMMC-6440 AMMC-6440 Datasheet
Privacy Policy | Disclaimer
© 2012 Datasheet Archive
