REPETITIVE AVALANCHE dv/dt RATED IRHM7360SE N-CHANNEL H
|
|
|
Top Searches for this datasheet
91224C
REPETITIVE AVALANCHE dv/dt RATED
IRHM7360SE
N-CHANNEL
HEXFET TRANSISTOR
SINGLE EVENT EFFECT (SEE) HARD
400Volt, 0.20, (SEE) HARD HEXFET
International Rectifier's (SEE) HARD technology HEXFETs demonstrate immunity failure. Additionally, under identical pre- post-radiation test conditions, International Rectifier's HARD HEXFETs retain identical electrical specifications Rads (Si) total dose. compensation gate drive circuitry required. These devices also capable surviving transient ionization pulses high 1012 Rads (Si)/Sec, return normal operation within microseconds. Since process utilizes International Rectifier's patented HEXFET technology, user expect highest quality reliability industry. HARD HEXFET transistors also feature well-established advantages MOSFETs, such voltage control, very fast switching, ease paralleling temperature stability electrical parameters. They well-suited applications such switching power supplies, motor controls, inverters, choppers, audio amplifiers high-energy pulse circuits space weapons environments.
Product Summary
Part Number IRHM7360SE BVDSS 400V RDS(on) 0.20
Features:
Radiation Hardened Rads (Si) Single Event Burnout (SEB) Hardened Single Event Gate Rupture (SEGR) Hardened Gamma (Flash X-Ray) Hardened Neutron Tolerant Identical Pre- Post-Electrical Test Conditions Repetitive Avalanche Rating Dynamic dv/dt Rating Simple Drive Requirements Ease Paralleling Hermetically Sealed Electrically Isolated Ceramic Eyelets
Absolute Maximum Ratings
Parameter
12V, 25°C 12V, 100°C 25°C dv/dt Continuous Drain Current Continuous Drain Current Pulsed Drain Current Max. Power Dissipation Linear Derating Factor Gate-to-Source Voltage Single Pulse Avalanche Energy Avalanche Current Repetitive Avalanche Energy Peak Diode Recovery dv/dt Operating Junction Storage Temperature Range Lead Temperature Weight
Pre-Irradiation
IRHM7360SE
(0.063 (1.6mm) from case sec.) (typical)
Units
W/°C V/ns
www.irf.com
10/13/98
IRHM7360SE Device
Pre-Irradiation
Electrical Characteristics 25°C (Unless Otherwise Specified)
Parameter
BVDSS Drain-to-Source Breakdown Voltage DSS/T Temperature Coefficient Breakdown Voltage RDS(on) Static Drain-to-Source On-State Resistance VGS(th) Gate Threshold Voltage Forward Transconductance IDSS Zero Gate Voltage Drain Current
Units
0.51 0.20 0.21 -100 V/°C
Test Conditions
1.0mA Reference 25°C, 1.0mA 12V, 12V, VGS, 1.0mA 15V, VDS= Rating,VGS=0V Rating 125°C -20V 12V, Rating 200V, 22A, 2.35
IGSS IGSS td(on) td(off)
Gate-to-Source Leakage Forward Gate-to-Source Leakage Reverse Total Gate Charge Gate-to-Source Charge Gate-to-Drain (`Miller') Charge Turn-On Delay Time Rise Time Turn-Off Delay Time Fall Time Internal Drain Inductance Internal Source Inductance
Measured from drain lead, (0.25 from package center die. Measured from source lead, (0.25 from package source bonding pad.
Modified MOSFET symbol showing internal inductances.
Ciss
Input Capacitance Output Capacitance Reverse Transfer Capacitance
4000 1000
1.0MHz
Source-Drain Diode Ratings Characteristics
Parameter
Continuous Source Current (Body Diode) Pulse Source Current (Body Diode) Diode Forward Voltage Reverse Recovery Time Reverse Recovery Charge Forward Turn-On Time
Units
Test Conditions
Modified MOSFET symbol showing integral reverse junction rectifier.
25°C, 22A, 25°C, 22A, di/dt 100A/µs
Intrinsic turn-on time negligible. Turn-on speed substantially controlled
Thermal Resistance
Parameter
RthJC RthCS RthJA Junction-to-Case Case-to-Sink Junction-to-Ambient
Units
0.50 0.21 °C/W
Test Conditions
Typical socket mount
www.irf.com
Radiation Characterstics
Radiation Performance Hard HEXFETs
International Rectifier Radiation Hardened HEXFETs tested verify their hardness capability. hardness assurance program International Rectifier comprises radiation environments. Every manufacturing tested dose rate (total dose) environment MlL-STD-750, test method 1019 condition International Rectifier imposed standard gate voltage volts note bias condition equal device rated voltage note Post-irradiation limits devices irradiated Rads (Si) presented Table column IRHM7360SE. values Table will either
IRHM7360SE Device
dose rate test circuits that used. Both pre- post-irradiation performance tested specified using same drive circuitry test conditions order provide direct comparison. should noted that radiation level Rads (Si) only parameter limit change VGSTh minimum. High dose rate testing done special request basis using dose rate 1012 Rads (Si)/Sec Table International Rectifier radiation hardened HEXFETs have been characterized heavy Single Event Effects (SEE) environments. Single Event Effects characterization shown Table
Table Dose Rate
Parameter
BVDSS VGS(th) IGSS IGSS IDSS RDS(on)1 Drain-to-Source Breakdown Voltage Gate Threshold Voltage Gate-to-Source Leakage Forward Gate-to-Source Leakage Reverse Zero Gate Voltage Drain Current Static Drain-to-Source On-State Resistance Diode Forward Voltage
IRHM7360SE
100K Rads (Si)
Units
Test Conditions
1.0mA VDS, 1.0mA -20V VDS=0.8 Rating, VGS=0V 12V, =14A 25°C, 22A,VGS
-100 0.20
Table High Dose Rate
Parameter
VDSS di/dt
1011 Rads (Si)/sec 1012 Rads (Si)/sec
Drain-to-Source Voltage
Units Test Conditions Applied drain-to-source voltage during gamma-dot Peak radiation induced photo-current A/µsec Rate rise photo-current Circuit inductance required limit di/dt
Table Single Event Effects
(Si) (MeV/mg/cm2)
Fluence (ions/cm2)
Range (µm)
VDSBias
Bias
www.irf.com
IRHM7360SE Device
Pre-Irradiation
Drain-to-Source Current
Drain-to-Source Current
9.0V 8.0V 7.0V 6.0V BOTTOM 5.0V
9.0V 8.0V 7.0V 6.0V BOTTOM 5.0V
5.0V
5.0V
20µs PULSE WIDTH
20us PULSE WIDTH
Drain-to-Source Voltage
Drain-to-Source Voltage
Typical Output Characteristics
Typical Output Characteristics
DS(on) Drain-to-Source Resistance (Normalized)
Drain-to-Source Current
20µs PULSE WIDTH
10.8 12.0
Gate-to-Source Voltage
Junction Temperature(
Typical Transfer Characteristics
Normalized On-Resistance Temperature
www.irf.com
-Irradiation
IRHM7360SE Device
8000
Gate-to-Source Voltage
Ciss Crss Coss
1MHz SHORTED
320V 200V
Capacitance (pF)
6000
Ciss
4000
Coss
2000
Crss
TEST CIRCUIT FIGURE
Drain-to-Source Voltage
Total Gate Charge (nC)
Typical Capacitance Drain-to-Source Voltage
Typical Gate Charge Gate-to-Source Voltage
1000
Reverse Drain Current
OPERATION THIS AREA LIMITED RDS(on)
Drain Current
10us
100us
Single Pulse
10ms 1000
,Source-to-Drain Voltage
Drain-to-Source Voltage
Typical Source-Drain Diode Forward Voltage
Maximum Safe Operating Area
www.irf.com
IRHM7360SE Device
Pre-Irradiation
D.U.T.
Drain Current
-VDD
Pulse Width Duty Factor
10a. Switching Time Test Circuit
Case Temperature
Maximum Drain Current Case Temperature
td(on)
d(off)
10b. Switching Time Waveforms
Thermal Response thJC
0.50 0.20 0.10 0.05 0.02 0.01 SINGLE PULSE (THERMAL RESPONSE) Notes: Duty factor Peak thJC 0.0001 0.001 0.01
0.01
0.001 0.00001
Rectangular Pulse Duration (sec)
Maximum Effective Transient Thermal Impedance, Junction-to-Case
www.irf.com
-Irradiation
IRHM7360SE Device
Single Pulse Avalanche Energy (mJ)
1000
BOTTOM
12a. Unclamped Inductive Test Circuit
Starting Junction Temperature
12c. Maximum Avalanche Energy Drain Current
12b. Unclamped Inductive Waveforms
Current Regulator Same Type D.U.T.
.2µF .3µF
D.U.T.
Charge
Current Sampling Resistors
13a. Basic Gate Charge Waveform
13b. Gate Charge Test Circuit
www.irf.com
IRHM7360SE Device
Repetitive Rating; Pulse width limited
maximum junction temperature. Refer current HEXFET reliability report. 50V, starting 25°C, [0.5 (IL2)] Peak 22A, 12V, 22A, di/dt 120A/µs, BVDSS, 150°C Suggested 2.35 Pulse width Duty Cycle
Pre-Irradiation
Total Dose Irradiation with Bias.
volt applied during irradiation MIL-STD-750, method 1019 condition Total Dose Irradiation with Bias. rated BVDSS (pre-radiation) applied during irradiation MlL-STD-750, method 1019 condition This test performed using flash x-ray source operated e-beam mode (energy ~2.5 MeV), nsec pulse. Pre-Radiation Post-Radiation test conditions identical facilitate direct comparison circuit applications.
Case Outline Dimensions TO-254AA
ITTE
LEGEND DRAIN SOURCE GATE
LEGEND DRAIN SOURCE GATE
Conforms JEDEC Outline TO-254AA Dimensions Millimeters Inches
CAUTION BERYLLIA WARNING MIL-PRF-19500 Package containing beryllia shall ground, sandblasted, machined, have other operations performed them which will produce beryllia beryllium dust. Furthermore, beryllium oxide packages shall placed acids that will produce fumes containing beryllium.
WORLD HEADQUARTERS: Kansas St., Segundo, California 90245, Tel: (310) 3331 GREAT BRITAIN: Hurst Green, Oxted, Surrey 9BB, Tel: 1883 732020 CANADA: Lincoln Court, Brampton, Ontario L6T3Z2, Tel: (905) 2200 GERMANY: Saalburgstrasse 157, 61350 Homburg Tel: 6172 96590 ITALY: Liguria 10071 Borgaro, Torino Tel: 0111 EAST: Bldg., 30-4 Nishi-Ikebukuro 3-Chome, Toshima-Ku, Tokyo Japan Tel: 3983 0086 SOUTHEAST ASIA: Seng Promenade, Great World City West Tower, 13-11, Singapore 237994 Tel: 4630 TAIWAN:16 Suite 207, Sec. South Road, Taipei, 10673, Taiwan Tel: 886-2-2377-9936 http://www.irf.com/ Data specifications subject change without notice. 10/98
www.irf.com
Other recent searches
ST-100 - ST-100 ST-100 Datasheet
SH-72 - SH-72 SH-72 Datasheet
PD3747 - PD3747 PD3747 Datasheet
BCV28 - BCV28 BCV28 Datasheet
BCV48 - BCV48 BCV48 Datasheet
BCV29 - BCV29 BCV29 Datasheet
BCV49 - BCV49 BCV49 Datasheet
Am29SL800D - Am29SL800D Am29SL800D Datasheet
2N5883 - 2N5883 2N5883 Datasheet
Privacy Policy | Disclaimer
© 2012 Datasheet Archive
