HA-2544 July 2004 FN2900.6 50MHz, Video Operational Amplifie

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

HA-2544 July 2004 FN2900.6 50MHz, Video Operational Amplifie

Datasheet Thumbnail

Top Searches for this datasheet

PROD OLETE REPLACEM MMEN RECOSheet nical ersil.com/ts Data Tech w.int contac TERSIL 888-IN
HA-2544
July 2004 FN2900.6
50MHz, Video Operational Amplifier
HA-2544 fast, unity gain stable, monolithic designed meet needs required accurate reproduction video high speed signals. offers high voltage gain (6kV/V) high phase margin degrees) while maintaining tight gain flatness over video bandwidth. Built from high quality Dielectric Isolation, HA-2544 another addition Intersil series high speed, wideband amps, offers true video performance combined with versatility amp. primary features HA-2544 include 50MHz Gain Bandwidth, 150V/µs slew rate, 0.03% differential gain error gain flatness just 0.12dB 10MHz. High performance power requirements with supply current only 10mA. Uses HA-2544 range from video test equipment, guidance systems, radar displays other precise imaging systems where stringent gain phase requirements have previously been with costly hybrids discrete circuitry. HA-2544 will also used non-video systems requiring high speed signal conditioning such data acquisition systems, medical electronics, specialized instrumentation communication systems. Military (/883) product data sheets available upon request.
Features
Gain Bandwidth 50MHz High Slew Rate 150V/µs Supply Current 10mA Differential Gain Error 0.03% Differential Phase Error 0.03 Degrees Gain Flatness 10MHz. 0.12dB
Applications
Video Systems Video Test Equipment Radar Displays Data Acquisition Systems Imaging Systems Pulse Amplifiers Signal Conditioning Circuits
Pinout
HA-2544C (PDIP) VIEW
Part Information
PART NUMBER (BRAND) HA3-2544C-5 TEMP. RANGE (oC) PACKAGE PDIP PKG. DWG. E8.3
CAUTION: These devices sensitive electrostatic discharge; follow proper Handling Procedures. 1-888-INTERSIL 321-724-7143 Intersil (and design) registered trademark Intersil Americas Inc. Copyright Intersil Americas Inc. 2003, 2004. Rights Reserved other trademarks mentioned property their respective owners.
HA-2544
Absolute Maximum Ratings
Voltage Between Terminals Differential Input Voltage (Note Peak Output Current ±40mA
Thermal Information
Thermal Resistance (Typical, Note (oC/W) (oC/W) PDIP Package Maximum Junction Temperature (Plastic Packages) 150oC Maximum Storage Temperature Range -65oC 150oC Maximum Lead Temperature (Soldering 10s) 300oC
Operating Conditions
Temperature Range HA-2544C-5 75oC
CAUTION: Stresses above those listed "Absolute Maximum Ratings" cause permanent damage device. This stress only rating operation device these other conditions above those indicated operational sections this specification implied.
NOTES: achieve optimum performance, input stage designed without protective diode clamps. Exceeding maximum differential input voltage results reverse breakdown base-emitter junction input transistors probable degradation input parameters especially VOS, Noise. measured with component mounted evaluation board free air.
Electrical Specifications
PARAMETER INPUT CHARACTERISTICS Offset Voltage
VSUPPLY ±15V, 10pF, Unless Otherwise Specified TEST CONDITIONS TEMP (oC) UNITS
Full Full Full Full Full Full
0.04 ±11.5
µV/oC µA/oC nA/oC nV/Hz pA/Hz µVP-P µVRMS
Average Offset Voltage Drift (Note Bias Current
Average Bias Current Drift (Note Offset Current
Offset Current Drift Common Mode Range Differential Input Resistance Differential Input Capacitance Input Noise Voltage Input Noise Current Input Noise Voltage (Note
1kHz 1kHz 0.1Hz 10Hz 0.1Hz 1MHz
TRANSFER CHARACTERISTICS Large Signal Voltage Gain (Note Full Common Mode Rejection Ratio (Note ±10V Minimum Stable Gain Unity Gain Bandwidth (Note Gain Bandwidth Product (Note Phase Margin ±100mV ±100mV kV/V kV/V Degrees
HA-2544
Electrical Specifications
PARAMETER OUTPUT CHARACTERISTICS Output Voltage Swing Full Power Bandwidth (Note Peak Output Current (Note Continuous Output Current (Note Output Resistance TRANSIENT RESPONSE Rise Time (Note Overshoot (Note Slew Rate Settling Time (Note VIDEO PARAMETERS (Note Differential Phase (Note Differential Gain (Notes Gain Flatness 5MHz 10MHz Chrominance Luminance Gain (Note Chrominance Luminance Delay (Note POWER SUPPLY CHARACTERISTICS Supply Current Power Supply Rejection Ratio (Note ±10V ±20V Full NOTES:
VSUPPLY ±15V, 10pF, Unless Otherwise Specified (Continued) TEST CONDITIONS TEMP (oC) UNITS
Full Open Loop
V/µs
0.03 0.0026 0.03 0.10 0.12
Degree
Rise Time Overshoot testing, VOUT measured from +200mV -200mV. Settling Time specified 0.1% final value step Slew Rate Full Power Bandwidth guaranteed equation: Full Power Bandwidth PEAK PEAK Refer typical performance curve Data Sheet. video parameter specifications will degrade output load resistance decreases. Tested with VM700A video tester, using NTC-7 Composite input signal. adequate test repeatability, minimum warm-up minutes suggested. Gain Delay less than resolution test equipment used which 0.1dB 7ns, respectively.
HA-2544 Test Circuits Waveforms
NOTES:
±15V.
VOUT
(Optional). 10pF. Large Signal ±5V. Small Signal +200mV -200mV.
FIGURE TRANSIENT RESPONSE
VOUT
VOUT
VOUT +10V Vertical Scale: 5V/Div.; VOUT 2V/Div. Horizontal Scale: 100ns/Div. LARGE SIGNAL RESPONSE
VOUT +200mV Vertical Scale: 100mV/Div.; VOUT 100mV/Div. Horizontal Scale: 100ns/Div. SMALL SIGNAL RESPONSE
SETTLING POINT
VOUT
NOTES: Feedback summing resistor ratios should 0.1% matched. HP5082-2810 clipping diodes recommended. Tektronix P6201 probe used settling point. FIGURE SETTLING TIME TEST CIRCUIT FIGURE OFFSET VOLTAGE ADJUSTMENT NOTE: Tested offset adjustment range |VOS 1mV| minimum referred output. Typical range approximately ±30mV.
HA-2544 Schematic Diagram
QP24 QP23 QP20 QN21 QP19 QP33 QP44 QN43 QN18 QP16 QN17 QP15 QN14 QN13 QN55 QN60 QN11 QN12 QN48 VBAL QN59 QN10 QP52 VQN51 +INPUT -INPUT QN53 OUTPUT QP54 QN22 QN36 QN50 QP57 QP58
QP32
QN46
Application Information
HA-2544 true differential that versatile offers advantages high unity gain bandwidth, high speed supply current. More important than general purpose applications that HA-2544 especially designed meet requirements found video amplifier system. These requirements include fine picture resolution accurate color rendition, must meet broadcast quality standards. video signal, video information carried amplitude phase well level. amplifier must pass 30Hz line rate Iuminance level 3.58MHz (NTSC) 4.43MHz (PAL) color band without altering phase gain. HA-2544's specifications aimed meeting this include high bandwidth (50MHz), very gain flatness (0.12dB 10MHz), near unmeasurable differential gain differential phase (0.03% 0.03 degrees), noise (20nV/Hz). HA-2544 meets these guidelines. HA-2544 also offers advantage full output voltage swing ±10V into load. This equates full power bandwidth 2.4MHz this ±10V signal. video signal levels maximum used (with 1k), full power bandwidth would 11.9MHz without clipping distortion.
HA-2544
Another usage might required direct load where HA-2544 will still swing this signal shown above display. important note that must realized that load resistance decreases video parameters also degraded. optimal video performance load recommended. lower supply voltages required, such ±5V, many characterization curves indicate where parameters vary. shown bandwidth, slew rate supply current still very well maintained. resistor 100) before capacitance effectively decouples this effect.
Stability/Phase Margin/Compensation
HA-2544 sacrificed unity gain stability achieving superb performance. this device, phase margin exceeds degrees unity crossing point open loop frequency response. Large phase margin critical order reduce differential phase differential gain errors caused most other amps. Because this part unity gain stable, compensation brought out. compensation desired reduce noise bandwidth, most standard methods used. method suggested inverting scheme would series from inverting node ground which will reduce bandwidth, effect slew rate. user wishes achieve even higher bandwidth (>50MHz), tolerate some slight gain peaking lower phase margin, experimenting with various load capacitance done. Shown Application excellent Differential Input, Unity Gain Buffer which also will terminate cable reject common mode voltages. Application method separating video signal into Sync only signal Video Blanking signal. Application shows HA-2544 being used 100kHz High Pass 2-Pole Butterworth Filter. Also shown measured frequency response curves.
Prototyping Board Layout
When designing with HA-2544 video with high performance device, care should taken high frequency layout techniques avoid unwanted parasitic effects. Short lead lengths, source impedance lower value feedback resistors help reduce unwanted poles zeros. This layout would also include ground plane construction power supply decoupling close supply pins with suggested parallel capacitors 0.1µF 0.001µF ceramic ground. noninverting configuration, amplifier sensitive stray capacitance (<40pF) ground inverting input. Therefore, inverting node connections should kept minimum. Phase shift will also introduced load parasitic capacitance increased. small series
Typical Applications
SHIELDED CABLE 1.21K 1.21K SYNC ONLY 1N5711
1.21K 1.21K HA-2544 COMPOSITE VIDEO
HA-2544 VIDEO BLANK 1N5711
FIGURE APPLICATION DIFFERENTIAL INPUT BUFFER
FIGURE APPLICATION COMPOSITE VIDEO SYNC SEPARATOR
-100 PHASE (DEGREES) 105.3kHz
2.1K 750pF INPUT 2.1K 750pF
HA-2544
OUTPUT
(2.1K 750pF) 100K
ATTENUATION (dB)
FIGURE APPLICATION 100kHz HIGH PASS 2-POLE BUTTERWORTH FILTER
FREQUENCY (Hz)
FIGURE MEASURED FREQUENCY RESPONSE APPLICATION
HA-2544 Typical Performance Curves
1000 INPUT NOISE VOLTAGE (nV/Hz) 1000 INPUT NOISE CURRENT (pA/Hz) OFFSET VOLTAGE (mV)
INPUT NOISE VOLTAGE
INPUT NOISE CURRENT
FREQUENCY (Hz)
100K
TEMPERATURE (oC)
FIGURE INPUT NOISE VOLTAGE NOISE CURRENT FREQUENCY
FIGURE INPUT OFFSET VOLTAGE TEMPERATURE TYPICAL UNITS)
BIAS CURRENT (µA)
±15V
0.1Hz 10Hz, Noise Voltage 0.97µVP-P
TEMPERATURE (oC)
FIGURE NOISE VOLTAGE 1000)
FIGURE INPUT BIAS CURRENT TEMPERATURE
PSRR CMRR (dB)
±15V CMRR OPEN LOOP GAIN (kV/V)
±15V -AVOL
+AVOL
-PSRR
+PSRR
TEMPERATURE (oC)
TEMPERATURE (oC)
FIGURE PSRR CMRR TEMPERATURE
FIGURE OPEN LOOP GAIN TEMPERATURE
HA-2544 Typical Performance Curves
OUTPUT VOLTAGE SWING SUPPLY VOLTAGE (±V) -VOUT OPEN LOOP 100M -55oC 25oC 125oC GAIN (dB) +VOUT OPEN LOOP
(Continued)
±15V
PHASE MARGIN (DEGREES) PHASE (DEGREES) PHASE (DEGREES)
100K FREQUENCY (Hz)
FIGURE OUTPUT VOLTAGE SWING SUPPLY VOLTAGE
FIGURE FREQUENCY RESPONSE VARIOUS GAINS
OUTPUT CURRENT (mA) SUPPLY VOLTAGE (±V) 100K FREQUENCY (Hz) VOUT ±100mV ±15V -55oC 25oC 125oC GAIN (dB) -135 -180 100M ±15V
FIGURE OUTPUT CURRENT SUPPLY VOLTAGE
FIGURE OPEN LOOP RESPONSE
NORMALIZED SUPPLY CURRENT SUPPLY VOLTAGE (±V) 125oC 25oC -55oC GAIN (dB)
VOUT ±100mV 10pF
±15V -135 -180 100M
100K FREQUENCY (Hz)
FIGURE SUPPLY CURRENT SUPPLY VOLTAGE (NORMALIZED ±15V 25oC)
FIGURE VOLTAGE FOLLOWER RESPONSE
HA-2544 Typical Video Performance Curves
DIFFERENTIAL PHASE (DEGREES) 0.004 0.003 DIFFERENTIAL GAIN (dB) 0.002 0.001 -0.001 -0.002 -0.003 -0.004 -0.005 -0.006 VOLTAGE LEVEL 3.58MHz 5.00MHz 0.200 0.150 0.100 0.050 -0.050 -0.100 -0.150 -0.200 -0.250 -0.300 VOLTAGE LEVEL 5.00MHz 3.58MHz SYSTEM ALONE
FIGURE GAIN VARIATION OFFSET LEVELS (DIFFERENTIAL GAIN)
FIGURE PHASE VARIATION OFFSET LEVELS (DIFFERENTIAL PHASE)
NTSC Method, Differential Gain 0.05% 75oC Visual Difference -55oC 125oC FIGURE DIFFERENTIAL GAIN
NTSC Method, Differential Phase 0.05 Degree 75oC Visual Difference -55oC 125oC FIGURE DIFFERENTIAL PHASE
±100mV 10pF 0.15 GAIN FLATNESS (dB) 0.10 0.05 -0.05 -0.10 -0.15 -0.20 100K FREQUENCY (Hz) 100M
INPUT
OUTPUT
NTSC Method, Delay 75oC Visual Difference -55oC 125oC Vertical Scale: Input 100mV/Div., Output 50mV/Div. Horizontal Scale: 500ns/Div. FIGURE CHROMINANCE LUMINANCE DELAY
FIGURE GAIN FLATNESS
HA-2544 Typical Video Performance Curves
(Continued)
(pF) BANDWIDTH (-3dB) 35.5 40.8 50.1 55.8 54.8 PHASE (-3dB) -77.1o -89.6o -122.0o -150.7o -179.1o ±15V
VOLTAGE GAIN (dB) -250.000ns 0.00000ns 250.000ns 100K
100M
VOUT
2.0V/Div., VOUT 2.0V/Div., Timebase 50ns FIGURE OUTPUT SWING (WITH RLOAD FREQUENCY 5.00MHz)
FIGURE BANDWIDTH LOAD CAPACITANCE
Characteristics
DIMENSIONS: mils mils mils 2030µm 1630µm 483µm METALLIZATION: Type: Thickness: PASSIVATION: Type: Nitride (Si3N4) over Silox (SiO2, Phos.) Silox Thickness: Nitride Thickness: SUBSTRATE POTENTIAL (POWERED UP): VTRANSISTOR COUNT: PROCESS: Bipolar Dielectric Isolation
Metallization Mask Layout
HA-2544
PHASE SHIFT (DEGREES)
HA-2544 Dual-In-Line Plastic Packages (PDIP)
INDEX AREA
E8.3 (JEDEC MS-001-BA ISSUE
LEAD DUAL-IN-LINE PLASTIC PACKAGE INCHES SYMBOL
MILLIMETERS 0.39 2.93 0.356 1.15 0.204 9.01 0.13 7.62 6.10 5.33 4.95 0.558 1.77 0.355 10.16 8.25 7.11 NOTES Rev. 12/93
0.015 0.115 0.014 0.045 0.008 0.355 0.005 0.300 0.240
0.210 0.195 0.022 0.070 0.014 0.400 0.325 0.280
BASE PLANE SEATING PLANE 0.010 (0.25)
NOTES: Controlling Dimensions: INCH. case conflict between English Metric dimensions, inch dimensions control. Dimensioning tolerancing ANSI Y14.5M-1982. Symbols defined Series Symbol List" Section Publication Dimensions measured with package seated JEDEC seating plane gauge GS-3. dimensions include mold flash protrusions. Mold flash protrusions shall exceed 0.010 inch (0.25mm). measured with leads constrained perpendicular datum measured lead tips with leads unconstrained. must zero greater. maximum dimensions include dambar protrusions. Dambar protrusions shall exceed 0.010 inch (0.25mm). maximum number terminal positions. Corner leads E8.3, E16.3, E18.3, E28.3, E42.6 will have dimension 0.030 0.045 inch (0.76 1.14mm).
0.100 0.300 0.115 0.430 0.150
2.54 7.62 10.92 3.81
2.93
Intersil U.S. products manufactured, assembled tested utilizing ISO9000 quality systems. Intersil Corporation's quality certifications viewed www.intersil.com/design/quality
Intersil products sold description only. Intersil Corporation reserves right make changes circuit design, software and/or specifications time without notice. Accordingly, reader cautioned verify that data sheets current before placing orders. Information furnished Intersil believed accurate reliable. However, responsibility assumed Intersil subsidiaries use; infringements patents other rights third parties which result from use. license granted implication otherwise under patent patent rights Intersil subsidiaries.
information regarding Intersil Corporation products, www.intersil.com

HA-2544 July 2004 FN2900.6 50MHz, Video Operational Amplifie

Top Searches for this datasheet

Other recent searches