Version Product Product Name Firmware Version Hardware Version EBM001

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

Version Product Product Name Firmware Version Hardware Version EBM001

Datasheet Thumbnail

Top Searches for this datasheet

Bluetooth Module Design Data Sheet
Version Product Product Name Firmware Version Hardware Version EBM001
class Bluetooth module
18.1 Rev.01
DESCRIPTION EBM001 certified V1.2. fully integrated Bluetooth Class module using BlueCore2-External solution which include Radio, Baseband, Link Manager, Host Control Interface. sufficient definitions, high receiving sensitivity, power consumption, cost, EBM-001 suitable need long distance transmission devices. whole compatible with EBM-002 Class module. FEATURE Comply with Bluetooth Specification V1.2 Support connection connection Support Faster connection, Flush timeout, Synchronisation, improvements, AFH, Parameter ranges Handle. PIO/ definitions ideally suited rapid embedded development kind products. interface UART interface with programmable baud rate Compact size (26x14.5x2.5mm) type product output power -12dBm (class High receiving sensitivity (-88 0.1%BER). compatible with EBM002 class module cost reduction. Output interface over USB/UART/PCM/SPI. Alternative built-in (EBM001-4) flash memory. (EBM001-8) flash memory. APPLICATIONS: Notebook PDA, Access Point, Dongle, Headset, UART adapter, Modem, Mouse, peripherals embedded products.
GENERAL SPECIFICATION
ITEMS Supply Voltage Carrier Frequency Modulation Method Maximum Data Rate Transmission Power Hopping Receiving Signal Range Receiver Frequency Baseband Crystal Output Interface Operation Temperature Storage Temperature
Absolute Supply Voltage
SPECIFICATION VDD: 3.3V+/-0.2V Regulated supply voltage 2400MHz 2483.5MHz(USA,Spain,France) GFSK,1Mbps,0.5BT Gaussian Asynchronous:723.2kbps/57.6kbps Synchronous:433.9kbps/433.9kbps +18dBm -12dBm; Power control stage 1600hops/sec, 1MHz channel space -88dBm 1.5MHz center frequency 16MHz USB,PCM,SPI,UART degree +105 degree 3.6V VDD,other +0.3V
Bluetooth Specification Specification
ELECTRICAL CHARACTERISTICS
Transmitter Section ITMES Transmission power ETC1 Initial Frequency Accuracy In-band spurious |M-N|=2 |M-N|3 Exception band spurious (Operation mode) 30MHz 1GHz 1GHz 12.75GHz 1.8GHz 1.9GHz 5.1GHz 5.3GHz ETC1
100kHz
Unit
Condition
Hopping ON/OFF Continuous hold 100kHz
Longest supported packet
NOTE5 ETC1
Adjacent Channel Power +/-2MHz >+/-3MHz Modulation Characteristics F1AVG F2MIN
00001111,Hopping 01010101,Hopping
F2AVG/F1AVG Frequency Drift ETC1
Drift rate:400Hz/10us
Operation current
Peak Current during bust
2)Receiver Section ITMES Sensitivity Single slot packet Multi slot packet Maximum received signal Out-band blocking 30MHz 2000MHz 2000MHz 2399MHz 2498MHz 3000MHz 3000MHz 12.75GHz (idle mode) 30MHz 1GHz 1GHz 12.75GHz 1.8GHz 1.9GHz 5.15GHz 5.3GHz Intermodulation Interference Performance Co-channel Image frequency Adjacent(1MHz) In-band image Unit Condition
10E-3,hopping
off/1600K returned payload Multi slot packets uses 10E-3,hopping 1600K
returned payload ,multi slot packet,DH1 Hopping off,BER 10E-3
Hopping off,BER 10E-3
NTC,BER 10E-3 Measured
hopping off.
DEFINITION
Name PIO2/USB_Pull_Up PIO3/USB_Wake_Up PIO4/USB_ON PIO5/USB_DETACH PIO6/CLK_REQ PIO7/RAM_CSB PIO8 PIO9 PIO10 PIO11 USB_DN USB_DP PCM_CLK PCM_IN PCM_SYNC PCM_OUT VSUP UART_RX UART_RTS UART_TX UART_CTS SPI_MOSI SPI_CLK SPI_CSB SPI_MISO RESET AIO1 AIO0 Description Transmitter receiver input Ground pull-up Output goes high wake when Programmable lines/Interrupt request line chip detaches from when this input line clock request external clock line Programmable Input/Output Line Programmable Input/Output Line Programmable Input/Output Line Programmable Input/Output Line Programmable Input/Output Line DataI/O Data+ Synchronous Data Clock Synchronous 8kss data Synchronous Data Output Ground Ground Ground circuit BlueCore2 CORE Asynchronous Serial Data UART ready send Asynchronous Serial Data Output UART clear send Synchronous Serial Interface Data Input Synchronous Serial Interface Clock Chip select Synchronous Serial Interface Synchronous Serial Interface Data Input Reset high Synchronous Data Strobe
Programmable Input/Output line Programmable Input/Output line Ground Ground Ground
PIO1/TXEN PIO0/RXEN
Ground Ground Control output external class only Control output external LNA(if fitted) Ground
Layout Guide
size 14.50*26.00mm. addition size 1.00*0.45mm ,and other 1.00*090mm. Both side pitch 1.27mm. behind need clearance plane approach R1.00mm space.

Version Product Product Name Firmware Version Hardware Version EBM001

Top Searches for this datasheet

Other recent searches