PDC4UV6414(D/E)-(75/102)T-S 32MByte CMOS, PC/100 Synchronous DRAM
|
|
|
Top Searches for this datasheet
January 1999 Revision
PDC4UV6414(D/E)-(75/102)T-S
32MByte CMOS, PC/100 Synchronous DRAM Module
General Description
PDC4UV6414(D/E)-(75/102)T-S high performance, 32-megabyte synchronous, dynamic module organized words bits, 168-pin, dual-in-line memory module (DIMM) package. modules utilize four Fujitsu MB81F641642(D/G)-(75/102)FN CMOS 4Mx16 synchronous dynamic RAMs surface mount package (TSOP) epoxy laminated substrate. Each device accompanied decoupling capacitor improved noise immunity. Byte Serial EEPROM contains module configuration information.
Features
High Density 32MByte Cycle Time (CL=3) 7.5ns (-75), 10ns (-102) Cycle Time (CL=2) 11.5ns (-75), 10ns (-102) Power: Active 3.0W (-75), 2.6W (-102) LVTTL-compatible inputs outputs Separate power ground planes improve noise immunity Single power supply 3.3V±0.3V Height: 1.375 inch
ABSOLUTE MAXIMUM RATINGS
Item Voltage relative Power Dissipation Operating Temperature Storage Temperate Short Circuit Output Current Symbol Topr Tstg Ratings -0.5 +4.6 +125 Unit
RECOMMENDED OPERATING CONDITIONS
Symbol Parameter Supply Voltage Ground Input High voltage Input voltage -0.5 VCC+0.5 Unit
Fujitsu Microelectronics, Inc./Fujitsu Mikroelektronik GmbH
January 1999 Revision
PDC4UV6414(D/E)-(75/102)T-S
Functional Diagram
DQMB5 DQMB4 DQMB1 DQMB0 CS0* CLK0 CKE0 DQMB2 DQMB3 DQMB6 DQMB7 CS2* CLK2
4Mx16 SDRAM
4Mx16 SDRAM
4Mx16 SDRAM
4Mx16 SDRAM
DQ0~DQ15
DQ32~DQ47
DQ16~DQ31
DQ48~DQ63
DQ0~DQ63
0.33µF 0.1µF SA0-SA2 A0-A2 Decoupling capacitors devices
EEPROM
(All specifications device subject change without notice.)
Notes:
A0~A10, BA0, devices WE*, RAS*, CAS* devices. Data CLKs terminated using series resistors. Clock Wiring:
CLK0, CLK2 15pF
SDRAM SDRAM
CLK1, CLK3 10pF
Fujitsu Microelectronics, Inc./Fujitsu Mikroelektronik GmbH
January 1999 Revision
PDC4UV6414(D/E)-(75/102)T-S
Name
A0~A11 BA0, DQ0~DQ63 CLK0~CLK3 RAS* CAS* CKE0 DQMB0-DQMB7 Addresses Bank Select Address Data Inputs/Outputs Clock Inputs Address Strobes Column Address Strobes Clock Enables Mask Enables CS0*;CS2* SA0-SA2
Designation DQ32 DQ33 DQ34 DQ35 DQ36 DQ37 DQ38 DQ39 DQ40 DQ41 DQ42 DQ43 DQ44 DQ45 DQ46 DQ47 CAS* DQMB4 DQMB5 RAS* CLK1
Chip Select Write Enable Decode Input Serial Clock Serial Data Input/Output Write Protect Power Supply Ground Connection
Designation CKE0 DQMB6 DQMB7 DQ48 DQ49 DQ50 DQ51 DQ52 DQ53 DQ54 DQ55 DQ56 DQ57 DQ58 DQ59 DQ60 DQ61 DQ62 DQ63 CLK3
Designation DQ10 DQ11 DQ12 DQ13 DQ14 DQ15 DQMB0 DQMB1 CS0* CLK0
Designation CS2* DQMB2 DQMB3 DQ16 DQ17 DQ18 DQ19 DQ20 DQ21 DQ22 DQ23 DQ24 DQ25 DQ26 DQ27 DQ28 DQ29 DQ30 DQ31 CLK2
Fujitsu Microelectronics, Inc./Fujitsu Mikroelektronik GmbH
January 1999 Revision
PDC4UV6414(D/E)-(75/102)T-S
SERIAL INFORMATION
Byte#
36-61
Function Described
Bytes Written into serial memory module Total bytes memory device Fundamental memory type Address this assembly Column Addresses this assembly Module Banks this assembly Data Width this assembly Data Width this assembly (continued) Voltage interface standard this assembly SDRAM cycle time CL=3 (tCLK) SDRAM Access from Clock CL=3 (tAC) DIMM configuration type Refresh Rate/Type SDRAM Width Primary DRAM SDRAM Data Width Min. clock delay, Back Back Random Column Addresses (ICCD) Burst Length Supported Banks each SDRAM device CAS# Latency Latency Write Latency SDRAM Module Attribute SDRAM Device Attribute Clock cycle Time CL=2 (tCLK) Max. Data Access Time from clock CL=2 (tAC) Clock cycle Time CL=1 (tCLK) Max. Data Access Time from clock CL=1 (tAC) Min. Precharge Time (tRP) Min. Active Delay (tRRD) Min. Delay (tRCD) Min. Pulse Width (tRAS) Module Bank Density Address Command Signal Input Setup Time before clock (tSI) Address Command Signal Input Hold Time after clock (tHI) Data Signal Input Setup Time before clock (tSI) Data Signal Input Hold Time after clock (tHI) Superset Information Revision Checksum bytes 0-62
Function Supported -102
bytes bytes SDRAM bits LVTTL 7.5ns 10ns Non-Parity S/R, Normal 15.6 1CLK
Value
JEDEC Calculation
-102
Full Non-Buffered/Registered Vcc, B/R, S/W, P/A, 11.5ns 10ns 22.5ns 20ns 15ns 20ns 22.5ns 20ns 45ns 50ns 32MB Rev. JEDEC Calculation
Fujitsu Microelectronics, Inc./Fujitsu Mikroelektronik GmbH
January 1999 Revision
PDC4UV6414(D/E)-(75/102)T-S
SERIAL INFORMATION (CONTINUED)
Function Supported Byte#
66-71 95-98 128-255
Value
44h/45h
Function Described
Manufacturers JEDEC code JEP-106E Manufacturers JEDEC code JEP-106E Manufacturers JEDEC code JEP-106E Manufacturing location Manufacturer's Part Number Manufacturer's Part Number Manufacturer's Part Number Manufacturer's Part Number Manufacturer's Part Number Manufacturer's Part Number Manufacturer's Part Number Manufacturer's Part Number Manufacturer's Part Number Manufacturer's Part Number Manufacturer's Part Number Manufacturer's Part Number Manufacturer's Part Number Manufacturer's Part Number Manufacturer's Part Number Manufacturer's Part Number Manufacturer's Part Number Manufacturer's Part Number Revision Code Revision Code Manufacturing Date Manufacturing Date Assembly Serial Number Manufacturer Specific Data Manufacturer Specific Data Manufacturer Specific Data Manufacturer Specific Data Manufacturer Specific Data Manufacturer Specific Data Manufacturer Specific Data Manufacturer Specific Data Manufacturer Specific Data Manufacturer Specific Data Manufacturer Specific Data Manufacturer Specific Data Manufacturer Specific Data Manufacturer Specific Data Manufacturer Specific Data Manufacturer Specific Data Manufacturer Specific Data Manufacturer Specific Data Manufacturer Specific Data Manufacturer Specific Data Manufacturer Specific Data Manufacturer Specific Data Manufacturer Specific Data Manufacturer Specific Data Manufacturer Specific Data Manufacturer Specific Data Manufacturer Specific Data Intel Spec. Frequency Intel Spec. Detail 100Mhz Open Read Write
-102
-102
Continuation code SMART's None Specific Data None None None Specific Data None DATE DATE Serial Number None None None 100Mhz 1010-1101 1010-1111 None
Specific Data DATE DATE S.No.
Fujitsu Microelectronics, Inc./Fujitsu Mikroelektronik GmbH
January 1999 Revision
PDC4UV6414(D/E)-(75/102)T-S
CHARACTERISTICS
recommended operating conditions unless otherwise noted) Notes
Value Parameter Output High Voltage Output Voltage Input Leakage Current (Any Input) Symbol VOH(DC) VOL(DC) -2mA VCC; other pins under test Dout Disable Burst: Length=4, BL=4, min. bank- active, Outputs open, Addresses changed 3-times during (min), Burst: Length=4 (each bank), BL=4 (each bank), min. banks active, Output open, Addresses changed 3-times during (min), CKE=VIL, banks idle, tCK=min, Power down mode, CKE=VIL, banks idle, CLK=H Power down mode, CKE=VIH, banks idle, tCK=min, commands only, Input signals (except CMD) changed time during clock cycles, CKE=VIH, banks idle, CLK=H Input signals stable, Conditions Min. Max. Unit
Output Leakage Current
ICC1S -102 Operating Current (Average Power Supply Current) ICC1D -102
ICC2P Precharge Standby Current (Power Supply Current) ICC2PS
Precharge Standby Current (Power Supply Current) -102 ICC2N
Precharge Standby Current (Power Supply Current)
ICC2NS
Fujitsu Microelectronics, Inc./Fujitsu Mikroelektronik GmbH
January 1999 Revision
PDC4UV6414(D/E)-(75/102)T-S
(Continued)
Value Parameter Symbol Test Condition Min. CKE=VIL, bank active, tCK=min, CKE=VIL, bank active, CKE=VIH, bank active, tCK=min, commands only, Input signals (except CMD) changed time during clock cycles, CKE=VIH, bank active, tCK=min, Burst length=4, Outputs open, Multiple-banks active, Gapless data, Max. Unit
ICC3P Active Standby Current (Power Supply Current) ICC3PS
Active Standby Current (Power Supply Current) -102 ICC3N
Active Standby Current (Power Supply Current)
ICC3NS
Burst mode Current (Average Power supply current) -102 ICC4
Refresh Current (Average Power Supply Current) -102 ICC5
Auto-refresh; tCK=min, tRC=min,
Refresh Current (Average Power Supply Current)
ICC6
Self-refresh; tCK=min,
0.2V,
CAS* Latency Notes: depends output termination load conditions, clock cycle rate, signal clocking rate; specified values obtained with output open termination register. initial pause (DESL NOP) required after power-up followed minimum eight Auto-refresh cycles.
Fujitsu Microelectronics, Inc./Fujitsu Mikroelektronik GmbH
January 1999 Revision
PDC4UV6414(D/E)-(75/102)T-S
CAPACITANCE
=+25°C, 3.3V±0.3V)
Parameter Input Capacitance (Address, WE*, CKE, RAS*, CAS*) Input Capacitance (DQMBs) Input Capacitance (CS0*, CS2*, CLK1, CLK3) Input Capacitance (CLK0, CLK2) Input/Output Capacitance (DQ0~DQ63) Notes: Symbol CI/O Max. Unit Note
Capacitance measured with Boonton Meter effective capacitance method. CAS* disable Dout.
CHARACTERISTICS: MB81F641642(D/G)-(75/102)
recommended operating conditions unless otherwise noted)
Parameter Latency=2 Latency=3 Symbol tCK2 tCK3 Latency=2 Latency=3 tAC2 tAC3 Latency=2 Latency=3 Latency=2 Latency=3 tHZ2 tHZ3 tREFI tCKSP
Notes 2,3,4
Min. 11.5 Max. Min. -102 Max. Notes
Unit
Clock Period Clock High Time Clock Time Input Setup Time Input Hold Time Access time from Clock (tCK=min) Output Low-Z Output High-Z
Output Hold Time
Time between Auto-Refresh command Interval Transition Time time Power Down Exit
Fujitsu Microelectronics, Inc./Fujitsu Mikroelektronik GmbH
January 1999 Revision
PDC4UV6414(D/E)-(75/102)T-S
BASE VALUES CLOCK COUNT/LATENCY: MB81F641642(D/G)-(75/102)
Parameter Cycle Time Precharge Time Active Time Delay Time Write Recovery Time Data-in Precharge Lead Time Data-in Active/ Refresh command period Mode Register cycle Time Bank Active Delay Time Latency=2 Latency=3 Symbol tRAS tRCD tDPL tDAL2 tDAL3 tRSC tRRD Unit Min. 67.5 22.5 22.5 1cyc+tRP 2cyc+tRP Max. 110000 Min. 1cyc+tRP 2cyc+tRP -102 Max. 110000 Notes
CLOCK COUNT FORMULA
(Note
Clock
Base Value Clock Period
(Round whole number)
LATENCY-FIXED VALUES: MB81F641642(D/G)-(75/102)
(The latency values these parameters fixed regardless clock period)
Parameter Clock Disable Output High-Z Input Data Delay Last Output Write Command Delay Write Command Input Data Delay Precharge Output High-Z Delay Burst Stop Command Output High-Z Delay Delay (min) Bank Delay (min)
Notes:
Symbol ICKE IDQZ IDQD IOWD IDWD IROH2 IROH3 IBSH2 IBSH3 ICCD ICBD
Unit cycle cycle cycle cycle cycle cycle
-102
Notes
cycle cycle cycle
depends output termination load conditions, clock cycle rate, signal clocking rate; specified values obtained with output open termination register. initial pause (DESL NOP) required after power-up followed minimum eight Auto-refresh cycles. characteristics assume capacitive load. reference level measuring timing input signals. Transition times measured between (min) (max). Assumes tRCD satisfied. also specifies access time burst mode. Specified where output buffer longer driven. Actual clock count (IRC) will clock count tRAS (IRAS) (IRP). Operation within tRCD (min) ensures that access time determined tRCD (min) (max); tRCD greater than specified tRCD (min), access time determined tAC. base values measured from clock edge command input clock edge next command input. clock counts calculated simple formula: clock count equals base value divided clock period (round whole number).
Fujitsu Microelectronics, Inc./Fujitsu Mikroelektronik GmbH
January 1999 Revision
PDC4UV6414(D/E)-(75/102)T-S
Fig. EXAMPLE TEST LOAD CIRCUIT
Output 1.4V
50pF
LVTTL
Note: characteristics measured this condition. This load circuits applicable VOL.
Fujitsu Microelectronics, Inc./Fujitsu Mikroelektronik GmbH
January 1999 Revision
PDC4UV6414(D/E)-(75/102)T-S
Physical Dimensions
168-pin (84x2) DIMM
5.250 0.088 0.175 0.450 1.375 5.171 5.014 0.102 (max.)
0.158
0.700 0.118
0.450 1.450 0.250 1.700 2.507
2.150 0.250
0.118 0.050 +0.004/-0.003
4.550 (Ref.) 5.014 0.350 0.123
Front View
0.079 Detail
Notes:
dimensions inches. behind back side.
Fujitsu Microelectronics, Inc./Fujitsu Mikroelektronik GmbH
January 1999 Revision
PDC4UV6414(D/E)-(75/102)T-S
Ordering Information
(10) (11) (12) (13) Memory Type SDRAM (PC/66) SGRAM SDRAM-Fast (PC/100) Module Shape SIMM DIMM Small Outline DIMM Module Count 72-pin 144-pin 168-pin 200-pin Word Depth 256K 512K Buffer Type Buffered Unbuffered Registered Operating Voltage Power Consumption 3.3V LVTTL Standard Power 3.3V LVTTL Power 3.3V SSTL Standard Power Data Width (ex. 64=x64, 72=x72 etc.) Device Configuration Refresh 2krf 4krf 8krf (10) Module Revision Applied "Standard" Blank Rev. Rev. Rev. (etc.) When DRAM device revised, revision changed (11) Clock Frequency SDRAM (PC/66) 100Mhz SDRAM-Fast (PC/100) (CL=3; tRCD=3; tRP=3) (CL=2; tRCD=2; tRP=2) (CL=3; tRCD=2; tRP=2) (CL=3; tRCD=3; tRP=3) (12) Package Component TSOP (13) Assembly Test Site SMART Modular Technologies
Fujitsu Microelectronics, Inc./Fujitsu Mikroelektronik GmbH
January 1999 Revision
PDC4UV6414(D/E)-(75/102)T-S
FUJITSU LIMITED
further information please contact:
Japan
FUJITSU LIMITED Memory Marketing Dept. 4-1-1, Kamikodanaka Nakahara-ku, Kawasaki 211-88, Japan Tel: +81-44-754-3767 Fax: +81-44-754-3343 Internet: http://www.fujitsu.co.jp/
North South America
FUJITSU MICROELECTRONICS, INC. 3545 North First Street Jose, 95134-1804, USA. Tel: +1-408-922-9000 Fax: +1-408-922-9179 Customer Response Center (Mon-Fri: 7am-5pm (PST)) Tel: +1-800-866-8608 Fax: +1-408-922-9179 Internet: http://www.fujitsumicro.com/ Rights Reserved. Circuit diagrams utilizing Fujitsu products included means illustrating typical semiconductor applications. Complete information sufficient construction purposes necessarily given. information given this document have been carefully checked believed reliable. However, Fujitsu assumes responsibility inaccuracies. information contained this document does convey licence under copyrights, patent rights trademarks claimed owned Fujitsu. Fujitsu reserves right change products specifications without notice. part this publication copied reproduced form means, transferred third party without prior written consent Fujitsu. information contained this document intended with equipments which require extremely high reliability such aerospace equipments, undersea repeaters, nuclear control systems medical equipments life support.
Europe
FUJITSU MIKROELEKTRONIK GmbH Siebenstein 6-10 63303 Dreieich-Buchschlag Germany Tel: +49-6103-690-0 Fax: +49-6103-690-122 Internet: http://www.fujitsu-ede.com/
Asia
FUJITSU MICROELECTRONICS ASIA LIMITED #05-08, Lorong Chuan NewTechPark Singapore 556741 Tel: +65-281-0770 Fax: +65-281-0220 Internet: http://www.fmap.com.sg/
©FUJITSU LIMITED 1998
Printed Germany
Fujitsu Microelectronics, Inc./Fujitsu Mikroelektronik GmbH
Other recent searches
STPS1535D - STPS1535D STPS1535D Datasheet
STPS1545D - STPS1545D STPS1545D Datasheet
SN74ABT8996 - SN74ABT8996 SN74ABT8996 Datasheet
SN54ABT8996 - SN54ABT8996 SN54ABT8996 Datasheet
MUR1560S - MUR1560S MUR1560S Datasheet
EBE25RC8AAFA - EBE25RC8AAFA EBE25RC8AAFA Datasheet
DR3001 - DR3001 DR3001 Datasheet
BTS723GW - BTS723GW BTS723GW Datasheet
Privacy Policy | Disclaimer
© 2012 Datasheet Archive
