DESCRIPTIO Supply Current: 600µA 3.3V Supply Current Shutdown: 0.

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

DESCRIPTIO Supply Current: 600µA 3.3V Supply Current Shutdown: 0.

Datasheet Thumbnail

Top Searches for this datasheet

LTC1348 3.3V/5V Power RS232 3-Driver/5-Receiver Transceiver
DESCRIPTIO
Supply Current: 600µA 3.3V Supply Current Shutdown: 0.2µA Supply Current Receiver Alive Mode: 15µA Protection over ±10kV Operates from Single 5.5V Supply Operates 120kBaud with 0.1µF Flying Capacitors Three-State Outputs High Impedance When Output Overvoltage Does Force Current Back into Supplies RS232 Lines Forced ±25V Without Damage Flowthrough Architecture
LTC1348 3-driver/5-receiver RS232 transceiver with very supply current. charge pump only requires five 0.1µF capacitors. LTC1348 provides full RS232 output levels when operated over wide supply range 5.5V transceiver operates four modes: Normal, Receiver Disable, Receiver Alive Shutdown. Normal Receiver Disable mode, only 600µA 3.3V 800µA load condition. Shutdown mode, supply current further reduced 0.2µA. Receiver Alive mode, five receivers kept alive supply current 15µA. RS232 outputs assume high impedance state Shutdown Receiver Alive mode with power off. receiver outputs assume high impedance state Receiver Disable with power off. LTC1348 fully compliant with data rate overvoltage RS232 specifications. transceiver operates 120kbaud with drivers loaded with 1000pF, Both driver outputs receiver inputs forced ±25V without damage survive multiple ±10kV strikes.
registered trademarks Linear Technology Corporation.
APPLICATI
Notebook Computers Palmtop Computers Printers Portable Instruments
TYPICAL APPLICATI
0.1µF 0.1µF 0.1µF LTC1348
3-Drivers/5-Receivers with Shutdown
0.1µF DREN RXEN
LT1348 TA01
0.1µF
SUPPLY CURRENT (mA)
3.3V 3.3V SHUTDOWN CURRENT QUIESCENT CURRENT
Supply Current
SHUTDOWN CURRENT (µA)
TEMPERATURE (°C)
LT1348
LTC1348 ABSOLUTE
(Note
RATI
PACKAGE/ORDER ATIO
VIEW PACKAGE 28-LEAD PLASTIC SSOP DREN RXEN PACKAGE 28-LEAD PLASTIC
Supply Voltage (VCC) Input Voltage Driver 0.3V 0.3V Receiver Driver/Receiver Enable 0.3V 0.3V Output Voltage Driver Receiver 0.3V 0.3V Short-Circuit Duration Driver Output Indefinite Receiver Output Indefinite Operating Temperature Range LTC1348C. 70°C LTC1348I. 40°C 85°C Storage Temperature Range 65°C 150°C Lead Temperature (Soldering, sec). 300°C
ORDER PART NUMBER LTC1348CG LTC1348CSW LTC1348IG LTC1348ISW
TJMAX 125°C, 96°C/W TJMAX 125°C, 85°C/W (SW)
Consult factory Military grade parts.
ELECTRICAL CHARACTERISTICS
5.5V, 0.1µF, unless otherwise noted.
PARAMETER Driver Output Voltage Swing Logic Input Voltage Level CONDITIONS 3.3V, Positive Negative
UNITS
Logic Input Current Output Short-Circuit Current Output Leakage Current Receiver Input Voltage Thresholds
Input Level (VOUT High) Input High Level (VOUT Low), 3.3V Input High Level (VOUT Low), VOUT Shutdown (Note Receiver Alive Mode (Note VOUT ±20V Input Threshold (Receiver Alive Mode) Input Threshold (Normal Mode) Input High Threshold (Normal Mode) Normal Mode ±10V Output Low, IOUT 1.6mA Output High, IOUT 160µA Sinking Current, VOUT Shutdown (Note VOUT
±500
Hysteresis Input Resistance Output Voltage Output Short-Circuit Current Output Leakage Current
0.6V
LTC1348
ELECTRICAL CHARACTERISTICS
5.5V, 0.1µF, unless otherwise noted.
PARAMETER Power Supply Generator Output Voltage Output Voltage Supply Rise Time Power Supply Supply Current CONDITIONS IOUT IOUT IOUT IOUT Shutdown Turn-On Load (Note 3.3V Load (Note Receiver Alive Mode (Note 3.3V Shutdown (Note 3.3V
UNITS
Supply Leakage Current (VCC) Driver/Receiver Enable Threshold Driver/Receiver Enable Threshold High Driver/Receiver Enable Threshold High
ELECTRICAL CHARACTERISTICS
5.5V, 0.1µF, unless otherwise noted.
PARAMETER Maximum Data Rate Slew Rate Driver Propagation Delay (TTL RS232) Receiver Propagation Delay (RS232 TTL) CONDITIONS 1000pF, Driver Switching 51pF 3.3V, 2500pF (Figure (Figure (Figure (Normal Mode) (Figure (Normal Mode) tHLR (Figure (Receiver Alive Mode) tLHR (Figure (Receiver Alive Mode)
UNITS kbps V/µs V/µs
denotes specifications which apply over full operating temperature range (0°C 70°C Commercial grade 40°C 85°C Industrial grade). Note Absolute Maximum Ratings those values beyond which life device impaired. Note Supply current measured with driver receiver outputs unloaded. VDREN VRXEN VCC.
Note Supply current measurement Shutdown performed with VDREN VRXEN Note Supply current measurement Receiver Alive mode performed with VDREN VRXEN VCC.
LTC1348
TYPICAL PERFORMANCE CHARACTERISTICS
Driver Output Voltage High/Low Load Capacitance (CL)
DRIVER OUTPUT VOLTAGE HIGH/LOW 250kbps 120kbps 64kbps OUTPUT HIGH 3.3V 0.1µF FLYING CAPACITORS DRIVERS LOADED DRIVER DRIVEN OUTPUT 64kbps 20kbps 250kbps 120kbps 20kbps
DRIVER OUTPUT VOLTAGE HIGH/LOW
SUPPLY CURRENT (mA)
3000 4000 1000 2000 LOAD CAPACITANCE (pF)
Driver Output Voltage High/Low Temperature (°C)
DRIVER OUTPUT VOLTAGE HIGH/LOW
3.3V OUTPUT HIGH
SHORT-CIRCUIT CURRENT (mA)
LEAKAGE CURRENT (µA)
DRIVERS LOADED WITH
OUTPUT 3.3V
TEMPERATURE (°C)
Driver Output Voltage High/Low Load Capacitance (CL)
Supply Current Driver Data Rate
OUTPUT LOADED 2500pF
120kbps
64kbps OUTPUT HIGH 20kbps
3.3V 0.1µF FLYING CAPACITORS DRIVERS DRIVEN LOADED OUTPUT 120kbps 64kbps 20kbps 3000 4000 1000 2000 LOAD CAPACITANCE (pF) 5000
LTC1348
OUTPUT LOADED 2500pF
3.3V DRIVER DATA RATE
5000
LTC1348
LTC1348
Driver Short-Circuit Current Temperature (°C)
3.3V TEMPERATURE (°C) ISC+ ISC-
Driver Leakage SHUTDOWN Temperature (°C)
3.3V
VOUT -20V
VOUT
TEMPERATURE (°C)
LTC1348
LTC1348 LTC1348
With 3.3V Driver Outputs Loaded with 1000pF. Driven 250kbps
DRIVEN DRIVER OUTPUT
DRIVER INPUT
LTC1348
LTC1348
CTIO
VCC: 5.5V Input Supply Pin. This should decoupled with 0.1µF ceramic capacitor. GND: Ground Pin. RXEN: TTL/CMOS Compatible Enable Pin. Refer Table functional description. DREN: TTL/CMOS Compatible Enable Pin. Refer Table functional description. Positive Supply Output (RS232 Drivers). This requires external capacitor 0.1µF charge storage. capacitor tied ground VCC. With multiple devices, pins paralleled into common capacitors. large numbers devices, increasing size shared common storage capacitors recommended reduce ripple. Negative Supply Output (RS232 Drivers). This requires external capacitor 0.1µF charge storage. C1+, C1-, C2+, C2-, C3+, C3-: Commutating Capacitor Inputs. These pins require three external capacitors 0.1µF: from C1-, another from another from C3-. maintain charge pump
Table Functional Description
MODE Shutdown ENABLE ENABLE DRIVERS Drivers Shutdown. Driver Outputs Assume High Impedance. Driver Pull-Up Resistors Disconnect From VCC. Drivers Alive. RECEIVERS Receivers Shutdown. Receiver Outputs Assume High Impedance. 0.2µA
Receiver Disable
Receiver Alive
Normal
efficiency, capacitor's effective series resistance should less than Ceramic capacitors recommended. RS232 Driver Input Pins. Inputs TTL/CMOS compatible. inputs unused drivers left unconnected since 300k input pull-up resistors included chip. minimize power consumption, internal driver pull-up resistors disconnected from Shutdown Receiver Alive mode. OUT: Driver Outputs RS232 Voltage Levels. Outputs high impedance state when Shutdown, Receiver Alive mode driver outputs protected against ±10kV human body model discharges. Receiver Inputs. These pins forced ±25V without damage. receiver inputs protected against ±10kV human body model discharges. Each receiver provides 0.4V hysteresis noise immunity. Receiver Alive mode receivers have hysteresis. OUT: Receiver Outputs with TTL/CMOS Voltage Levels. Outputs high impedance state when Shutdown Receiver Disable mode allow data line sharing.
Receiver Outputs Three-State.
600µA 3.3V, 800µA 15µA
Drivers Shutdown. Driver Outputs Three-State. Driver Pull-Up Resistors Disconnect From VCC. Drivers Alive.
Receivers Alive.
Receivers Alive.
600µA 3.3V, 800µA
LTC1348
SWITCHI WAVEFOR
DRIVER INPUT DRIVER OUTPUT 1.4V 1.4V
LTC1348
Figure Driver Propagation Delay Timing
TEST CIRCUITS
DRIVER INPUT DRIVER OUTPUT DRIVER 51pF
LTC1348
Figure Driver Timing Test Load
OUTPUT INPUT 51pF
LTC1348
Figure Receiver Timing Test Load
APPLICATIONS INFORMATION
Power Supply LTC1348 includes onboard voltage-tripling charge pump capable generating from single 3.3V supply. This allows LTC1348 drivers provide guaranteed RS232-compliant voltage levels with 3.3V supply. With outputs loaded with LTC1348 typically swing with voltages 2.85V. will meet ±3.7V EIA562 levels with supply voltages 2.2V. charge pump requires three external flying capacitors operate; 0.1µF ceramic capacitors adequate most applications. applications requiring extremely high data rates abnormally heavy output loads, 0.33µF flying capacitors recommended. Bypass output capacitor values should match those flying capacitors capacitors should mounted close package possible.
INPUT OUTPUT
1.7V
1.3V 2.4V
LTC1348
0.8V
Figure Receiver Propagation Delay Timing
Test Circuit
0.1µF 0.1µF 0.1µF 0.1µF
LT1348
LTC1348
0.1µF 0.1µF
RS232 LINE PINS PROTECTED ±10kV
DREN RXEN
LTC1348 APPLICATIONS INFORMATION
High Data Rates LTC1348 maintains true RS232 minimum driver output even high data rates. Figure shows test circuit with wires connecting test chips. Both chips from 3.3V supplies. Figure shows typical line waveforms with three drivers, loaded with 1000pF toggling simultaneously 120kbaud. Figure shows
0.1µF 0.1µF
LTC1348
0.1µF 0.1µF DREN RXEN
LTC1348
0.1µF
1000pF
0.1µF 0.1µF
LTC1348
0.1µF 0.1µF DRIVER DRIVER DRIVER DREN RXEN
LT1348
0.1µF
1000pF 1000pF
Figure Data Rate Evaluation Circuit
LTC1348
Information furnished Linear Technology Corporation believed accurate reliable. However, responsibility assumed use. Linear Technology Corporation makes representation that interconnection circuits described herein will infringe existing patent rights.
same circuit with single 1000pF/3k loaded driver driven 250kbaud, other drivers loaded toggling. This closely approximates actual behavior RS232 serial port, with only driver (TX) driven high speed other drivers (RTS DTR) driven relatively data rate Under same conditions, LTC1348 fast 350kbaud still meet EIA562 (±3.7V) minimum driver output levels.
DRIVER OUTPUT
RECEIVER OUTPUT
DRIVER INPUT
Figure Driver Test Result 120kbps
DRIVER OUTPUT
RECEIVER OUTPUT
DRIVER INPUT
Figure Driver Test Results 250kbps
LTC1348
PACKAGE DESCRIPTION
0.205 0.212** (5.20 5.38)
0.301 0.311 (7.65 7.90) 0.002 0.008 (0.05 0.21)
0.005 0.009 (0.13 0.22)
0.022 0.037 (0.55 0.95)
*DIMENSIONS INCLUDE MOLD FLASH. MOLD FLASH SHALL EXCEED 0.006" (0.152mm) SIDE **DIMENSIONS INCLUDE INTERLEAD FLASH. INTERLEAD FLASH SHALL EXCEED 0.010" (0.254mm) SIDE
0.291 0.299** (7.391 7.595) 0.010 0.029 (0.254 0.737) 0.093 0.104 (2.362 2.642) 0.037 0.045 (0.940 1.143)
0.009 0.013 (0.229 0.330)
0.014 0.019 0.016 0.050 (0.356 0.482) (0.406 1.270) NOTE: IDENT, NOTCH CAVITIES BOTTOM PACKAGES MANUFACTURING OPTIONS. PART SUPPLIED WITH WITHOUT OPTIONS *DIMENSION DOES INCLUDE MOLD FLASH. MOLD FLASH SHALL EXCEED 0.006" (0.152mm) SIDE **DIMENSION DOES INCLUDE INTERLEAD FLASH. INTERLEAD FLASH SHALL EXCEED 0.010" (0.254mm) SIDE
NOTE
0.050 (1.270)
RELATED PARTS
PART NUMBER LT1137A LTC1327 LT1330 LT1331 LTC1347 DESCRIPTION 3-DR/5-RX RS232 Transceiver 3-DR/5-RX RS562 Transceiver 3-DR/5-RX RS232 3-DR/5-RX RS232/RS562 Transceiver 3-DR/5-RX Micropower RS232 Transceiver COMMENTS ±15kV IEC-801-2 Protection 3.3V Operation Logic Interface RS232 RS562 Operation Receivers Active Shutdown
Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, 95035-7417 (408) 432-1900 FAX: (408) 434-0507q TELEX: 499-3977 www.linear-tech.com
Dimensions inches (millimeters) unless otherwise noted. Package 28-Lead Plastic SSOP (0.209)
(LTC 05-08-1640)
0.068 0.078 (1.73 1.99)
0.397 0.407* (10.07 10.33)
0.0256 (0.65)
0.010 0.015 (0.25 0.38)
SSOP 0694
Package 28-Lead Plastic Small Outline (Wide 0.300)
(LTC 05-08-1620)
0.697 0.712* (17.70 18.08)
NOTE 0.004 0.012 (0.102 0.305)
0.394 0.419 (10.007 10.643)
(WIDE) 0396
1348fa LT/GP 0197 PRINTED
LINEAR TECHNOLOGY CORPORATION 1994

DESCRIPTIO Supply Current: 600µA 3.3V Supply Current Shutdown: 0.

Top Searches for this datasheet

Other recent searches