Miniature SMD, Dual Output DC/DC Converters Efficiency 1000VDC Is

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

Miniature SMD, Dual Output DC/DC Converters Efficiency 1000VDC Is

Datasheet Thumbnail

Top Searches for this datasheet

MSAU200 Series
Miniature SMD, Dual Output DC/DC Converters
Efficiency 1000VDC Isolation MTBF 2,000,000 Hours Cost Input 12VDC Output {15VDC Temperature Performance -40] +85] Lead Frame Technology 94V-0 Package Material Interanl Construction
Minmax's MSAU200 DC/DC's "gull-wing" package, weigh mere grams meet 245]/10sec solder-reflow lead free process. series consists models with input voltages 12VDC which offers standard dual output voltages {5V, {9V, {12V {15VDC choice. Their impressive guaranteed efficiencies enable models deliver their fully rated output power from -40] +85] without heat sinking forced-air cooling. MSAU200 series excellent selection variety applications including data communication equipments, distributed power systems, telecommunication equipments, industrial robot systems. MSAU200 units available tape reel package.
Isolation
1000
Cost Profile
Block Diagram
+Vin Bipolar Push-Pull Inverter -Vin Com.
MINMAX
REV:0 2005/04
MSAU200 Series
Model Selection Guide
Model Number Input Voltage Output Voltage Output Current Input Current Load Regulation Efficiency
MSAU201 MSAU202 MSAU203 MSAU204 MSAU211 MSAU212 MSAU213 MSAU214 10.8 13.2
Max. {100 {100
Min. {0.8 {0.7 {0.8 {0.7
@Max. Load (Typ.)
Load (Typ.)
(Max.)
@Max. Load (Typ.)
Absolute Maximum Ratings
Parameter Input Surge Voltage 1000 Internal Power Dissipation 5VDC Input Models 12VDC Input Models Min. -0.7 -0.7 -Max. Unit
Notes
Specifications typical Ta=+25], resistive load, nominal input voltage, rated output current unless otherwise noted. Ripple Noise measurement bandwidth 0-20 MHz. These power converters require minimum output loading maintain specified regulation. Operation under no-load conditions will damage these modules; however, they meet specifications listed.
Lead Temperature (1.5mm from case Sec.)
Exceeding absolute maximum ratings unit could cause damage. These continuous operating ratings.
Environmental Specifications
Parameter Operating Temperature Operating Temperature Storage Temperature Humidity Cooling Conditions Ambient Case Min. -Free-Air Convection Max. +125 Unit
DC/DC converters should externally fused front protection. Other input output voltage available, please contact factory. Specifications subject change without notice.
Input Specifications
Parameter Input Voltage Range Reverse Polarity Input Current Input Filter Model Input Models Input Models Models Min. 10.8 -Typ. -Max. 13.2 Unit
Internal Capacitor
REV:0 2005/04
MINMAX
MSAU200 Series
Output Specifications
Parameter Output Voltage Accuracy Output Voltage Balance Line Regulation Load Regulation Ripple Noise (20MHz) Ripple Noise (20MHz) Ripple Noise (20MHz) Over Load Temperature Coefficient Output Short Circuit Over Line, Load Temp. Dual Output, Balanced Loads Change Io=20% 100% Conditions Min. -120 -0.5 Second Max. Typ. {1.0 {0.1 {1.2 -{0.01 Max. {3.0 {1.0 {1.5 -{0.02 Unit
Model Selection Guide
General Specifications
Parameter Isolation Voltage Rated Isolation Voltage Test Isolation Resistance Isolation Capacitance Switching Frequency MTBF MIL-HDBK-217F 25], Ground Benign Conditions Seconds Flash Tested Second 500VDC 100KHz,1V Min. 1000 1100 1000 2000 Typ. -Max. -100 -Unit Hours
Capacitive Load
Models Vout Maximum Capacitive Load each output {12V {15V Unit
Input Fuse Selection Guide
Input Models 500mA Slow Blow Type Input Models 200mA Slow Blow Type
MINMAX
REV:0 2005/04
MSAU200 Series
Efficiency
Efficiency
Input Voltage High
Load Current
Efficiency Input Voltage
Efficiency Output Load
Output Power
100LFM
400LFM 200LFM
Natural convection
Ambient Temperature
Derating Curve
REV:0 2005/04
MINMAX
MSAU200 Series
Test Configurations
Input Reflected-Ripple Current Test Setup
Input reflected-ripple current measured with inductor (4.7uH) (220uF, 1.0[ KHz) simulate source impedance. Capacitor Cin, offsets possible battery impedance. Current ripple measured input terminals module, measurement bandwidth 0-500 KHz.
Oscilloscope Battery Current Probe
Power Source -Vin -Out +Vin Converter +Out Load
KHz) capacitor 2.2uF input devices, 1.0uF devices.
+Vin
+Out Load
Output Ripple Reduction
good quality capacitor placed close practicable across load will give best ripple noise performance. reduce output ripple, recommended 0.47uF capacitors output.
Power Source -Vin +Vin +Out Dual Output Com. Converter -Out Cout Load
Converter -Vin -Out
Peak-to-Peak Output Noise Measurement Test
Cout 0.33uF ceramic capacitor. Scope measurement should made using socket, measurement bandwidth 0-20 MHz. Position load between from DC/DC Converter.
+Vin Dual Output Converter -Vin +Out Com. Cout -Out Scope Copper Strip Cout Scope Resistive Load
Thermal Considerations
Many conditions affect thermal performance power module, such orientation, airflow over module board spacing. avoid exceeding maximum temperature rating components inside power module, case temperature must kept below 90°C. derating curves determined from measurements obtained experimental apparatus.
Design Feature Considerations
Maximum Capacitive Load
MSAU200 series limitation maximum connected capacitance output. power module operated current limiting mode during start-up, affecting ramp-up startup time. optimum performance recommend 33uF maximum capacitive load. maximum capacitance found data sheet.
Position velocity probe thermocouple 15mm 0.6in
50mm
Flow
Input Source Impedance
power module should connected ac-impedance input source. Highly inductive source impedances affect stability power module. applications where power supplied over long lines output loading high, necessary capacitor input ensure startup. Capacitor mounted close power module helps ensure stability unit, recommended good quality Equivalent Series Resistance (ESR 1.0[
MINMAX
REV:0 2005/04
MSAU200 Series
Mechanical Data
0.3[0.01]
Connecting Patterns
View 2.54 inch grids
15.24 [0.60]
[0.31]
10.16mm
1.7mm
0.9[0.04]
[Magnification
[0.24]
10.8mm
0.60 [0.024]
[0.08]
2.54mm
1.0mm
[0.27]
SEATING PLANE
[0.01]
2.54 [0.100] 10.2 [0.40]
[0.28]
11.2 [0.44]
Tolerance
Millimeters X.X{0.25 X.XX{0.13
Inches X.XX{0.01 X.XXX{0.005 {0.002
{0.05
Connections
Function -Vin +Vin Common -Vout +Vout Available Electrical Connection
[0.36]
Physical Characteristics
Case Size 15.24*8.0*6.8 0.60*0.31*0.27 inches Molding 1.8g UL94V-0
Case Material Weight Flammability
MSAU200 converter encapsulated thermal resistance molding compound that excellent resistance/electrical characteristics over wide temperature range high humidity environments. encapsulant unit case both rated 94V-0 flammability specifications. Leads plated improved solderability.
REV:0 2005/04
MINMAX
MSAU200 Series
Packaging Specifications
30.4 2.0+1
330.0
100.0
13.00± 0.25
dimentions
Tape
Sprocket hole 1.55 +0.1 4.00 2.00 Sprocket hole tolerance over pitches
11.50 1.75 15.75 24.00±
dimentions XX.XX±
1.50 +0.25
Direction Unreeling
11.60
16.00
0.05
7.20
0.30
MINMAX
REV:0 2005/04
MSAU200 Series
Tube
14.5
10.4
Tube material: dimensions 0.25mm
+/-1.5
Packaging Details
Packaging Style Tube Tape Reel 286-3 Specifications Quantity
REV:0 2005/04
MINMAX

Miniature SMD, Dual Output DC/DC Converters Efficiency 1000VDC Is

Top Searches for this datasheet

Other recent searches