Revision 2.1, March 2004 Part Number 82-000530-01 Copyright Infor
|
|
|
Top Searches for this datasheet
ADSP-21161N EZ-KIT Lite® Evaluation System Manual
Revision 2.1, March 2004 Part Number 82-000530-01
Copyright Information
2004 Analog Devices, Inc., RIGHTS RESERVED. This document reproduced form without prior, express written consent from Analog Devices, Inc. Printed USA.
Limited Warranty
EZ-KIT Lite evaluation system warranted against defects materials workmanship period year from date purchase from Analog Devices from authorized dealer.
Disclaimer
Analog Devices, Inc. reserves right change this product without prior notice. Information furnished Analog Devices believed accurate reliable. However, responsibility assumed Analog Devices use; infringement patents other rights third parties which result from use. license granted implication otherwise under patent rights Analog Devices, Inc.
Trademark Service Mark Notice
Analog Devices logo, VisualDSP++, VisualDSP++ logo, SHARC, SHARC logo, CROSSCORE, CROSSCORE logo, EZ-KIT Lite registered trademarks Analog Devices, Inc. other brand product names trademarks service marks their respective owners.
Regulatory Compliance
ADSP-21161N EZ-KIT Lite evaluation system been certified comply with essential requirements European directive 89/336/EEC (inclusive 93/68/EEC) and, therefore, carries "CE" mark. ADSP-21161N EZ-KIT Lite evaluation system been appended Technical Construction File referenced "DSPTOOLS1" dated December 1997 awarded Certification appointed European Competent Body listed below. Technical Certificate Z600ANA1.005 Issued
Technology International (Europe) Limited Shrivenham Hundred Business Park Shrivenham, Swindon, 8TZ,
EZ-KIT Lite evaluation system contains (electrostatic discharge) sensitive devices. Electrostatic charges readily accumulate human body equipment discharge without detection. Permanent damage occur devices subjected high-energy discharges. Proper precautions recommended avoid performance degradation loss functionality. Store unused EZ-KIT Lite boards protective shipping package.
CONTENTS
ADSP-21161N EZ-KIT Lite Evaluation System Manual
CONTENTS
PREFACE
Purpose This Manual Intended Audience Manual Contents What's This Manual Technical Customer Support Supported Processors Product Information MyAnalog.com xvii Product Information xvii Related Documents xviii Online Documentation Printed Manuals VisualDSP++ Documentation Hardware Manuals Data Sheets Contacting Publications Notation Conventions
ADSP-21161N EZ-KIT Lite Evaluation System Manual
CONTENTS
GETTING STARTED
Contents EZ-KIT Lite Package Configuration Installation Tasks Installing VisualDSP++ EZ-KIT Lite Software Installing Registering VisualDSP++ License Setting EZ-KIT Lite Hardware Installing EZ-KIT Lite Driver Windows Driver Windows 2000 Driver 1-11 Windows Driver 1-12 Verifying Driver Installation 1-14 Starting VisualDSP++ 1-16
USING EZ-KIT LITE
EZ-KIT Lite License Restrictions Memory Using SDRAM Memory Using FLAG Pins Using Interrupt Pins Using Audio Interface Example Programs Using Flash Programmer Utility Using EZ-KIT Lite VisualDSP++ Interface
ADSP-21161N EZ-KIT Lite Evaluation System Manual
CONTENTS
Boot Load Target Options While Target Halted Emulator Exit Options 2-10 Other Options 2-10 Core Hang Conditions 2-11 Hardware Breakpoints 2-12 Common Hardware Breakpoint Attributes 2-13 Global Hardware Breakpoint Options 2-13 Data Hardware Breakpoints 2-15 Instruction Hardware Breakpoints 2-16 Other Breakpoints 2-17 Tips Tricks Using Hardware Breakpoints 2-18 Latency 2-18 Restrictions 2-18 Setting Breakpoint Single Address 2-18 Restricted Software Breakpoints 2-19
EZ-KIT LITE HARDWARE REFERENCE
System Architecture External Port Host Processor Interface (HPI) SPORT Audio Interface Audio Interface Breadboard Area JTAG Emulation Port
ADSP-21161N EZ-KIT Lite Evaluation System Manual
CONTENTS
Jumper Settings SDRAM Disable Jumper (JP1) SPDIF Selection Jumper (JP2) MCLK Selection Jumper (JP3) FLAG0 Enable Jumper (JP4) FLAG1 Enable Jumper (JP5) Sample Frequency Jumper (JP6) ADC2 Input Mode Selection Jumpers (JP7-8) Gain Selection Jumpers (JP9-10) ADC1 Input Selection Jumper (JP11) Processor Jumper (JP19) 3-10 Boot Mode Selection Jumper (JP20) 3-10 Clock Mode Selection Jumper (JP21) 3-11 ~BMS Enable Jumper (JP22) 3-12 AD1836 Control Selection Jumper (JP23) 3-12 Enable Jumper (JP26) 3-12 Enable Jumper (JP27) 3-12 LEDs Push Buttons 3-13 Reset LEDs (LED1 LED8) 3-14 FLAG LEDs (LED2-7) 3-14 VERF (LED9) 3-14 Monitor (LED10) 3-15 Power (LED11) 3-15 Programmable FLAG Push Buttons (SW1-4) 3-15
viii
ADSP-21161N EZ-KIT Lite Evaluation System Manual
CONTENTS
Interrupt Push Buttons (SW5-7) 3-15 Board Reset Push Button (SW8) 3-16 Connectors 3-16 Connector (P2) 3-16 Audio Connectors (P4-8, P17) 3-18 External Port Connector (P9) 3-18 Host Processor Interface Connector (P10) 3-19 JTAG Connector (P12) 3-19 Link Port Connectors (P13-14) 3-19 SPORT1 SPORT3 Connector (P15) 3-20 Power Connector (P16) 3-20 Specifications 3-21 Power Supply 3-21 Board Current Measurements 3-21
BILL MATERIALS INDEX
ADSP-21161N EZ-KIT Lite Evaluation System Manual
CONTENTS
ADSP-21161N EZ-KIT Lite Evaluation System Manual
PREFACE
Thank purchasing ADSP-21161N EZ-KIT Lite®, Analog Devices (ADI) evaluation system SHARC® processors. SHARC processors based 32-bit super Harvard architecture that includes unique memory architecture comprised large on-chip, dual-ported SRAM blocks coupled with sophisticated processor, which gives SHARC bandwidth sustained high-speed computations. SHARC represents today's facto standard floating-point targeted premium audio applications. evaluation system designed used conjunction with VisualDSP++® development environment test capabilities ADSP-21161N SHARC processors. VisualDSP++ development environment gives ability perform advanced application code development debug, such Create, compile, assemble, link application programs written C++, ADSP-21161N assembly Load, run, step, halt, breakpoints application program Read write data program memory Read write core peripheral registers Plot memory Access ADSP-21161N processor from personal computer (PC) achieved through port optional JTAG emulator. interface gives unrestricted access ADSP-21161N processor
ADSP-21161N EZ-KIT Lite Evaluation System Manual
evaluation board peripherals. Analog Devices JTAG emulators offer faster communication between host target hardware. Analog Devices carries wide range in-circuit emulation products. learn more about Analog Devices emulators development tools, ADSP-21161N EZ-KIT Lite provides example programs demonstrate capabilities evaluation board. VisualDSP++ license provided with this EZ-KIT Lite evaluation system limits size user program words internal memory. board features: Analog Devices ADSP-21161N processor Core Clock Speed Core Clock Mode Jumper Configurable Analog Devices AD1836 Audio Codec Jumper Selectable Line-In Mic-In Stereo Jack Line-Out Stereo Jack Jacks Audio Input Jacks Audio Output Analog Devices AD1852 Auxiliary Crystal Semiconductor CS8414 SPDIF Receiver Optical Coaxial Connectors SPDIF Input Flash Memory 512K 8-bits
ADSP-21161N EZ-KIT Lite Evaluation System Manual
Preface
Interface Connectors 14-Pin Emulator Connector JTAG Interface SPORT Connectors Link Port Link Port External Port Connectors (not populated) General-Purpose Push Button Flags Push Button Interrupts Outputs Analog Devices ADP3338 ADP3339 Voltage Regulators Breadboard area with typical footprints EZ-KIT Lite board Flash memory device that used store user-specific boot code. configuring jumpers EPROM boot, board stand-alone unit. ADSP-21161N EZ-KIT Lite package contains Flash programmer utility, which allows program flash memory. "Using Flash Programmer Utility" described page 2-8. SPORT2 connect audio codec, facilitating creation audio-signal processing applications. SPORT1 SPORT3 connect off-board connectors other serial devices.
SPORT0
Additionally, EZ-KIT Lite board provides un-installed expansion connector footprints that allow connect processor's External Port (EP) Host Processor Interface (HPI).
ADSP-21161N EZ-KIT Lite Evaluation System Manual
xiii
Purpose This Manual
Purpose This Manual
ADSP-21161N EZ-KIT Lite Evaluation System Manual provides instructions using hardware installing software your text includes guidelines running your code ADSP-21161N EZ-KIT Lite. manual also describes board's configuration components. Finally, schematic bill materials provided reference future ADSP-21161N board designs.
Intended Audience
This manual user's guide reference ADSP-21161N EZ-KIT Lite evaluation system. Programmers familiar with Analog Devices SHARC processor architecture, operation, programming primary audience this manual. Programmers unfamiliar with Analog Devices SHARC processors this manual conjunction with ADSP-21161 SHARC Processor Hardware Reference ADSP-21160 SHARC Processor Instruction Reference, which describe DSP'a architecture instruction set. Programmers unfamiliar with VisualDSP++ should refer VisualDSP++ online Help VisualDSP++ user's getting started guides. locations these documents, "Related Documents" page -xviii.
ADSP-21161N EZ-KIT Lite Evaluation System Manual
Preface
Manual Contents
manual consists Chapter "Getting Started" page Provides software hardware installation procedures, system requirements, basic board information. Chapter "Using EZ-KIT Lite" page Provides information EZ-KIT Lite from programmer's perspective provides simplified memory map. Chapter "EZ-KIT Lite Hardware Reference" page Provides information hardware aspects evaluation system. Appendix "Bill Materials" page Provides list components used manufacture EZ-KIT Lite board. Appendix "Schematics" page Provides resources allow EZ-KIT Lite board-level debugging reference design. appendix part online Help. online Help viewers should version ADSP-21161N EZ-KIT Lite Evaluation System Manual located Docs\EZ-KIT Lite Manuals folder installation schematics.
What's This Manual
This third edition ADSP-21161N EZ-KIT Lite Evaluation System Manual. edition includes updated installation license registration procedures.
ADSP-21161N EZ-KIT Lite Evaluation System Manual
Technical Customer Support
Technical Customer Support
reach Tools Support following ways. Visit Development Tools website
Email questions
dsptools.support@analog.com
Phone questions 1-800-ANALOGD Contact your local sales office authorized distributor Send questions mail
Analog Devices, Inc. Technology P.O. 9106 Norwood, 02062-9106
Supported Processors
ADSP-21161N EZ-KIT Lite evaluation system supports Analog Devices ADSP-21161N SHARC processors.
Product Information
obtain product information from Analog Devices website, from product CD-ROM, from printed publications (manuals).
ADSP-21161N EZ-KIT Lite Evaluation System Manual
Preface
Analog Devices online www.analog.com. website provides information about broad range products-analog integrated circuits, amplifiers, converters, digital signal processors.
MyAnalog.com
MyAnalog.com free feature Analog Devices website that allows customization webpage display only latest information products interested also choose receive weekly email notification containing updates webpages that meet your interests. MyAnalog.com provides access books, application notes, data sheets, code examples, more. Registration: Visit www.myanalog.com sign Click Register MyAnalog.com. Registration takes about five minutes serves means select information want receive. already registered user, just Your user name your email address.
Product Information
information digital signal processors, visit website www.analog.com/dsp, which provides access technical publications, data sheets, application notes, product overviews, product announcements. also obtain additional information about Analog Devices products following ways. Email questions requests information
dsp.support@analog.com
questions requests information 1-781-461-3010 (North America) 76903-157 (Europe)
ADSP-21161N EZ-KIT Lite Evaluation System Manual
xvii
Product Information
Related Documents
information product related development software, following publications. Table Related Publications
Title ADSP-21161N Data Sheet Description General functional description, pinout, timing
ADSP-21161 SHARC Processor Hardware Refer- Description internal processor architecture, ence registers, peripheral functions ADSP-21160 SHARC Processor Instruction Reference Description allowed processor assembly instructions
Table Related VisualDSP++ Publications
Title Description
VisualDSP++ User's Guide 32-Bit Proces- Detailed description VisualDSP++ feasors tures usage VisualDSP++ Assembler Preprocessor Manual SHARC Processors VisualDSP++ C/C++ Complier Library Manual SHARC Processors VisualDSP++ Linker Utilities Manual 32-Bit Processors VisualDSP++ Loader Manual 32-Bit Processors Description assembler function commands SHARC processors Description complier function commands SHARC processors Description linker function commands 32-bit processors Description loader function commands 32-bit processors
xviii
ADSP-21161N EZ-KIT Lite Evaluation System Manual
Preface
listed documents found through online Help Docs folder your VisualDSP++ installation. Most documents available printed form. plan EZ-KIT Lite board conjunction with JTAG emulator, refer documentation that accompanies emulator.
Online Documentation
Your software installation includes online Help part Windows® interface. These help files provide information about VisualDSP++ ADSP-21161N EZ-KIT Lite evaluation system. view VisualDSP++ Help, click Help menu item Windows task select Start ->Programs ->Analog Devices->VisualDSP++ 32-bit Processors ->VisualDSP++ Documentation. view ADSP-21161N EZ-KIT Lite Help, which part VisualDSP++ Help system, Contents Help window select Manuals ->Hardware Tools ->EZ-KIT Lite Evaluation Systems. more documentation, please
Printed Manuals
general questions regarding literature ordering, call Literature Center 1-800-ANALOGD (1-800-262-5643) follow prompts. VisualDSP++ Documentation Printed copies VisualDSP++ manuals purchased through Analog Devices Customer Service 1-781-329-4700; Customer Service representative. manuals purchased only kit. additional information, call 1-603-883-2430.
ADSP-21161N EZ-KIT Lite Evaluation System Manual
Product Information
have account with Analog Devices, will referred Analog Devices distributors. information distributors, onto Hardware Manuals Printed copies hardware reference instruction reference manuals ordered through Literature Center downloaded from Analog Devices website. phone number 1-800-ANALOGD (1-800-262-5643). manuals ordered title product number located back cover each manual. Data Sheets data sheets downloaded from Analog Devices website. general rule, printed copies data sheets with letter suffix obtained from Literature Center 1-800-ANALOGD (1-800-262-5643) downloaded from website. Data sheets without suffix downloaded from website only-no hard copies available. data sheet part name product number. want have data sheet faxed you, phone number that service 1-800-446-6212. Follow prompts list data sheet code numbers will faxed you. Call Literature Center first find requested data sheets available.
Contacting Publications
Please send your comments recommendations improve manuals online Help. contact dsp.techpubs@analog.com.
ADSP-21161N EZ-KIT Lite Evaluation System Manual
Preface
Notation Conventions
following table identifies describes text conventions used this manual. Additional conventions, which apply only specific chapters, appear throughout this document.
Example Close command (File menu)
{this that}
Description Text bold style indicates location item within VisualDSP++ environment's boards' menu system user interface items. Alternative required items syntax descriptions appear within curly brackets separated vertical bars; read example this that. Optional items syntax descriptions appear within brackets separated vertical bars; read example optional this that. Optional item lists syntax descriptions appear within brackets delimited commas terminated with ellipsis; read example optional comma-separated list this. Registers, connectors, pins, commands, directives, keywords, code examples, feature names text with letter gothic font. Non-keyword placeholders appear text with italic style format. Note: note providing information special interest identifying related topic. online version this book, word Note appears instead this symbol. caution providing information about critical design programming issues that influence operation product. online version this book, word Caution appears instead this symbol.
[this that]
[this,.]
PF9-0
filename
Caution:
ADSP-21161N EZ-KIT Lite Evaluation System Manual
Notation Conventions
xxii
ADSP-21161N EZ-KIT Lite Evaluation System Manual
GETTING STARTED
This chapter provides information need begin using ADSP-21161N EZ-KIT Lite evaluation system. correct operation, install software hardware order presented "Installation Tasks" page 1-3. chapter includes following sections. "Contents EZ-KIT Lite Package" page Provides list components shipped with this EZ-KIT Lite evaluation system. Configuration" page Describes minimum requirements work with EZ-KIT Lite. "Installation Tasks" page Describes step-by-step procedures setting hardware software.
Contents EZ-KIT Lite Package
Your ADSP-21161N EZ-KIT Lite evaluation system package contains following items. ADSP-21161N EZ-KIT Lite board EZ-KIT Lite Installation Procedure VisualDSP++ Installation Quick Reference Card
ADSP-21161N EZ-KIT Lite Evaluation System Manual
Contents EZ-KIT Lite Package
containing: VisualDSP++ 32-bit processors with limited license ADSP-21161N EZ-KIT Lite debug software driver files Example programs ADSP-21161N EZ-KIT Lite Evaluation System Manual (this document) Universal power supply type cable Registration card (please fill return) item missing, contact vendor where purchased your EZ-KIT Lite contact Analog Devices, Inc.
EZ-KIT Lite evaluation system contains (electrostatic discharge) sensitive devices. Electrostatic charges readily accumulate human body equipment discharge without detection. Permanent damage occur devices subjected high-energy discharges. Proper precautions recommended avoid performance degradation loss functionality. Store unused EZ-KIT Lite boards protective shipping package.
ADSP-21161N EZ-KIT Lite Evaluation System Manual
Getting Started
Configuration
correct operation VisualDSP++ software EZ-KIT Lite, your computer must have minimum configuration:
Windows Windows 2000, Windows Intel comparable) 166MHz processor Monitor color video card 2-button mouse free hard drive Full-speed port CD-ROM Drive
EZ-KIT Lite does under Windows Windows
Installation Tasks
following task list provided safe effective ADSP-21161N EZ-KIT Lite. Follow instructions presented order ensure correct operation your software hardware. VisualDSP++ EZ-KIT Lite software installation VisualDSP++ license installation registration EZ-KIT Lite hardware setup EZ-KIT Lite driver installation driver installation verification VisualDSP++ startup
ADSP-21161N EZ-KIT Lite Evaluation System Manual
Installation Tasks
Installing VisualDSP++ EZ-KIT Lite Software
This EZ-KIT Lite comes with latest version VisualDSP++ 32-bit processors. VisualDSP++ installation includes EZ-KIT Lite installations. install VisualDSP++ EZ-KIT Lite software: Insert VisualDSP++ installation into CD-ROM drive. Autoplay enabled your Install Shield Wizard Welcome screen. Otherwise, choose from Start menu, enter D:\ADI_Setup.exe Open field, where name your local CD-ROM drive. Follow on-screen instructions continue installing software. Custom Setup screen, select your EZ-KIT Lite from list available systems choose installation directory. Click icon Feature Description field selected system's description. When have finished, click Next. Ready Install screen, click Back change your install options, click Install install software, click Cancel exit install. When EZ-KIT Lite installs, Wizard Completed screen appears. Click Finish.
Installing Registering VisualDSP++ License
VisualDSP++ EZ-KIT Lites licensed products. only copy software each license purchased. Once copy VisualDSP++ EZ-KIT Lite software installed your must install, register, validate your licence.
ADSP-21161N EZ-KIT Lite Evaluation System Manual
Getting Started
VisualDSP++ Installation Quick Reference Card included your package will guide through licence installation registration process (refer Tasks
Setting EZ-KIT Lite Hardware
EZ-KIT Lite evaluation system contains (electrostatic discharge) sensitive devices. Electrostatic charges readily accumulate human body equipment discharge without detection. Permanent damage occur devices subjected high-energy discharges. Proper precautions recommended avoid performance degradation loss functionality. Store unused EZ-KIT Lite boards protective shipping package.
ADSP-21161N EZ-KIT Lite board designed outside your personal computer stand-alone unit. have open your computer case. connect EZ-KIT Lite board: Remove EZ-KIT Lite board from package. careful when handling board avoid discharge static electricity, which damage some components. Figure shows default jumper settings, connector locations, LEDs used installation. Confirm that your board default configuration before moving next step. Plug provided power supply into EZ-KIT Lite board. Visually verify that green power (LED11) Also verify that RESET LEDs (LED1 LED8) moment then off.
ADSP-21161N EZ-KIT Lite Evaluation System Manual
Installation Tasks
Monitor: LED10 Reset: LED8 Reset: LED1 Power: LED11
Figure 1-1. EZ-KIT Lite Hardware Setup Connect cable available full-speed port your other ADSP-21161N EZ-KIT Lite board.
Installing EZ-KIT Lite Driver
EZ-KIT Lite evaluation system installed following platforms requires full-speed port. "Windows Driver" page describes installation Windows "Windows 2000 Driver" page 1-11 describes installation Windows 2000.
ADSP-21161N EZ-KIT Lite Evaluation System Manual
Getting Started
"Windows Driver" page 1-12 describes installation Windows
driver used debug agent Microsoft certified because intended development laboratory environment, commercial environment. Windows Driver Before using ADSP-21161N EZ-KIT Lite first time, Windows driver must first installed. install driver: Insert into CD-ROM drive. connection device port activates Windows Hardware Wizard shown Figure 1-2.
Figure 1-2. Windows Hardware Wizard Click Next.
ADSP-21161N EZ-KIT Lite Evaluation System Manual
Installation Tasks
Select Search best driver your device, shown Figure 1-3.
Figure 1-3. Windows Searching Driver Click Next. Select CD-ROM drive, shown Figure 1-4.
Figure 1-4. Windows Searching CD-ROM ADSP-21161N EZ-KIT Lite Evaluation System Manual
Getting Started
Click Next. Windows locates WmUSBEz.inf file installation shown Figure 1-5.
Figure 1-5. Windows Locating Driver Click Next. Coping Files dialog appears (Figure 1-6).
Figure 1-6. Windows Searching .SYS File
ADSP-21161N EZ-KIT Lite Evaluation System Manual
Installation Tasks
Click Browse. Open dialog box, shown Figure 1-7, appears screen.
Figure 1-7. Windows Opening .SYS File Drives, select your CD-ROM drive. Click Copying Files dialog (Figure 1-8) appears.
Figure 1-8. Windows Copying .SYS File
1-10
ADSP-21161N EZ-KIT Lite Evaluation System Manual
Getting Started
Click driver installation complete, shown Figure 1-9.
Figure 1-9. Windows Completing Software Installation Click Finish exit wizard. 13.Verify installation following instructions "Verifying Driver Installation" page 1-14. Windows 2000 Driver VisualDSP++ installation software pre-installs necessary drivers selected EZ-KIT Lite. install also upgrades older driver such detected system. Prior running VisualDSP++ installer, ensure there other Hardware Wizard windows running background. there wizard windows running, close them before starting installer.
ADSP-21161N EZ-KIT Lite Evaluation System Manual
1-11
Installation Tasks
install driver: VisualDSP++ already installed your system, step Otherwise, VisualDSP++ installation. Refer VisualDSP++ Installation Quick Reference Card detailed installation description. When installing VisualDSP++ Windows 2000, make sure appropriate EZ-KIT Lite component selected installation. Connect EZ-KIT Lite device your PC's port. Windows 2000 automatically detects EZ-KIT device automatically installs appropriate driver selected device (see step Verify installation following instructions "Verifying Driver Installation" page 1-14. Windows Driver VisualDSP++ installation software pre-installs necessary drivers selected EZ-KIT Lite. install also upgrades older driver such detected system. Prior running VisualDSP++ installer, ensure there other Hardware Wizard windows running background. there wizard windows running, close them before starting installer. install driver: VisualDSP++ already installed your system, step Otherwise, VisualDSP++ installation. Refer VisualDSP++ Installation Quick Reference Card detailed
1-12
ADSP-21161N EZ-KIT Lite Evaluation System Manual
Getting Started
installation description. When installing VisualDSP++ Windows make sure appropriate EZ-KIT Lite component selected installation. Connect EZ-KIT Lite device your PC's port. connecting device port activate Windows Found Hardware Wizard, shown Figure 1-10.
Figure 1-10. Windows Found Hardware Wizard Select Install software automatically (Recommended) click Next.
ADSP-21161N EZ-KIT Lite Evaluation System Manual
1-13
Installation Tasks
When Windows completes driver installation selected device (see step window shown Figure 1-11 appears screen.
Figure 1-11. Windows Completing Driver Installation Verify installation following instructions "Verifying Driver Installation".
Verifying Driver Installation
Before launching EZ-KIT Lite evaluation system, verify that driver software installed properly: Ensure that cable connects evaluation board Press release RESET button (SW8) evaluation board. Verify that RESET (LED8) blinks once then blinks again seconds.
1-14
ADSP-21161N EZ-KIT Lite Evaluation System Manual
Getting Started
After RESET (LED8) blinks second time, verify that yellow monitor (LED10) lit. This signifies that board communicating properly with host ready VisualDSP++. Verify that driver software installed properly. Open Windows Device Manager verify that ADSP-21161N EZ-KIT Lite shows under Development Tools with exclamation point, Figure 1-12.
Figure 1-12. Device Manager Window using EZ-KIT Lite Windows disconnect cable from board before booting When Windows booted logged re-connect cable board. operation should continue normally from this point.
ADSP-21161N EZ-KIT Lite Evaluation System Manual
1-15
Installation Tasks
Starting VisualDSP++
session VisualDSP++: Verify that yellow monitor (LED10, located near connector) lit. This signifies that board communicating properly with host ready VisualDSP++. Hold down Control (CTRL) key. Select Start button Windows taskbar, then choose Programs->Analog Devices ->VisualDSP++ 32-bit Processors->VisualDSP++ Environment. running VisualDSP++ first time, step already have existing sessions, Session List dialog appears screen. Click Session. Session dialog box, shown Figure 1-13, appears screen.
Figure 1-13. Session Dialog Debug Target, choose EZ-KIT Lite (ADSP-21161N).
1-16
ADSP-21161N EZ-KIT Lite Evaluation System Manual
Getting Started
Processor, choose appropriate processor, ADSP-21161N. Type target name Session Name accept default name. Click return Session List. Highlight session click Activate.
ADSP-21161N EZ-KIT Lite Evaluation System Manual
1-17
Installation Tasks
1-18
ADSP-21161N EZ-KIT Lite Evaluation System Manual
USING EZ-KIT LITE
This chapter provides specific information assist with developing programs ADSP-21161N EZ-KIT Lite evaluation system. This information appears following sections. "EZ-KIT Lite License Restrictions" page Describes restrictions VisualDSP++ license shipped with EZ-KIT Lite. "Memory Map" page Defines ADSP-21161N EZ-KIT Lite's memory map. "Using SDRAM Memory" page Defines register values configure on-board SDRAM. "Using FLAG Pins" page Describes board's FLAG pins. "Using Interrupt Pins" page Describes board's interrupt pins. "Using Audio Interface" page Describes board's audio interface. "Example Programs" page Provides information about example programs included ADSP-21161N EZ-KIT Lite. "Using Flash Programmer Utility" page Provides information Flash Programmer utility included with EZ-KIT Lite software.
ADSP-21161N EZ-KIT Lite Evaluation System Manual
EZ-KIT Lite License Restrictions
"Using EZ-KIT Lite VisualDSP++ Interface" page Describes trace, performance monitoring, boot loading, context switching, target options facilities EZ-KIT Lite system. detailed information program ADSP-21161N SHARC processor, refer documents referenced "Related Documents".
EZ-KIT Lite License Restrictions
license shipped with EZ-KIT Lite imposes following restrictions. size user program's code limited words (1/4) ADSP-21161N processor's program memory space. connections simulator emulator sessions allowed. EZ-KIT Lite hardware must connected powered order VisualDSP++ with license.
Memory
ADSP-21161N processors includes Mbit internal SRAM program storage data storage. configuration internal SRAM detailed ADSP-21161 SHARC Processor Hardware Reference. ADSP-21161N EZ-KIT Lite board contains 512K 8-bits external Flash memory. Flash memory connected processors's ~MS1 ~BMS memory select pins. Flash memory accessed either boot memory space external memory space. external memory interface also connected 48-bit SDRAM memory. Flash memory connected ~MS0 pin.
ADSP-21161N EZ-KIT Lite Evaluation System Manual
Using EZ-KIT Lite
Table 2-1. EZ-KIT Lite Evaluation Board Memory
Start Address
0x0000 0000 0x0002 0000
Address
0x0001 FFFF 0x0002 1FFF 0x0002 9FFF 0x0004 3FFF 0x0005 3FFF 0x0008 7FFF 0x000A 7FFF 0x001F FFFF 0x002F FFFF 0x047F FFFF 0x0BFF FFFF 0x0FFF FFFF
Content Registers (Internal) Block Long Word Addressing Block Long Word Addressing Block Normal Word Addressing Block Normal Word Addressing Block Short Word Addressing Block Short Word Addressing Multi-processor Memory Space External Memory Space Bank (SDRAM) External Memory Space Bank (FLASH) External Memory Space Bank External Memory Space Bank
Internal Memory
0x0002 8000 0x0004 0000 0x0005 0000 0x0008 0000 0x000A 0000 0x0010 0000 0x0020 0000
External Memory
0x0400 0000 0x0800 0000 0x0C00 0000
Using SDRAM Memory
SDRAM memory, SDRAM control registers values shown Listing 2-1. Listing 2-1. ADSP-21161N EZ-KIT Lite SDRAM Settings
SDRAM Controller Setup ADSP-21161N EZ-KIT Lite Assumes SDRAM part# Micron MT48LC16M16A1-7SE (1Mx16-bit, banks) Default Factory Hardware settings (rev2.3) LK_CFG[1:0]= 10,~CLDBL=1 CLKIN=25 MHz, CCLK=100
SDRAMs bits wide total 3x(1Mx16-bit) 48-bit
ADSP-21161N EZ-KIT Lite Evaluation System Manual
Using SDRAM Memory
Mapped addresses 0x00200000-0x002fffff Estimated SDCLK SDCKR=0 Latency) CL=2 SDCL=2 [CAS Latency] tRAS=42ns tRP=21ns tRCD=20ns SDTRAS=5*2=10 [precharge delay] SDTRP=3*2=6 SDTRCD=2*2=4 [active delay] Settings must double counted SDCKR-bit=0, except
[CAS-to-RAS delay]
tREF=64ms/4K rows
SDRDIV= (100MHz*64ms/4096) 1549 0x60D cycles Note: change clock, have change settings best performance init_21161_SDRAM_controller: ustat1=dm(WAIT); ustat1 0x000FFFFF; dm(WAIT)=ustat1; ustat1=0x60D; dm(SDRDIV)=ustat1; ustat1=0x040146A2; dm(SDCTL)=ustat1; rts; mask SDRAM settings refresh rate clear wait state count
SDRAM registers configured automatically through debugger. Checking Manual External configuration Target Options dialog box, shown Figure page 2-10, disables automatic setting.
ADSP-21161N EZ-KIT Lite Evaluation System Manual
Using EZ-KIT Lite
Using FLAG Pins
ADSP-21161N holds asynchronous FLAG pins. these pins (FLAG0-9) available interaction with running program. After processor reset, FLAGs configured inputs. directions FLAGs configured though MODE2 register read though FLAG registers. FLAG registers summarized Table 2-2. more information FLAGs, refer ADSP-21161 SHARC Processor Hardware Reference. Table 2-2. FLAG Summary
FLAG1
FLAG0
Connects
SW1/AD1836_SPI_SELECT
Description
FLAG0
connects push button user input select AD1836 audio codec. connects push button user input select AD1852 auxiliary DAC. connects push button user connects push button user input.
FLAG1
SW2/AD1852_SPI_SELECT
FLAG1
FLAG2
FLAG2
FLAG3
FLAG3
input.
FLAG4-FLAG9 LED2-LED7 FLAG4-9
connect LEDs EZ-KIT Lite board user output.
FLAG10 FLAG11
connected available connector P10.
available
FLAG0-FLAG3
ADSP-21161N EZ-KIT Lite Evaluation System Manual
Using Interrupt Pins
Using Interrupt Pins
ADSP-21161N holds three interrupt pins (IRQ0-2) that interact with running program. Each three external interrupts directly accessible through push button switches SW5-SW7 EZ-KIT Lite board. Interrupt pins summarized Table 2-3. more information, refer ADSP-21161 SHARC Processor Hardware Reference. Table 2-3. Interrupt Summary
Interrupt1
IRQ0 IRQ1 IRQ2
Connects
Description connect push buttons supply feedback program execution. instance, write your code trigger FLAG when routine complete.
IRQ0-2
IRQ0-3
available connector P10.
Using Audio Interface
audio interface consists AD1836 audio codec, AD1852 auxiliary CS8414 SPDIF receiver. SPORT0 SPORT2 connect audio devices provide channels stereo input channel digital, channels analog) channels stereo output. Analog audio input facilitated stereo jack (P7) four mono jacks (P6). AD1836 stereo input channels dedicated mono jacks. other stereo input channels either supplied stereo jack other mono jacks. JP11 determines which jack used audio input. Digital audio input provided either single mono jack (P5) optical input connector (P4). determines source. Three stereo out-
ADSP-21161N EZ-KIT Lite Evaluation System Manual
Using EZ-KIT Lite
channels come from AD1836, while final channel from AD1852. "Audio Connectors (P4-8, P17)" page 3-18 more information about connectors. AD1836 multi-channel codec features digital-to-analog converters (DACs) four analog-to-digital converters (ADCs) supports multiple digital stereo channels with 24-bit conversion resolution sample rate. AD1836 features dynamic range each DACs dynamic range four ADCs. AD1836 configured through port. ADSP-21161N processor capable accessing AD1836's port through port well through SPORT1. more information, "AD1836 Control Selection Jumper (JP23)" page 3-12. AD1852 complete 18/20/24-bit single-chip stereo digital audio playback system. comprised multibit sigma-delta modulator, digital interpolation filters, analog output drive circuitry. Other features include on-chip stereo attenuator mute, programmed through SPI-compatible serial control port. AD1852 fully compatible with known formats, including sample frequencies bits. also backwards compatible supporting 50/15µs digital de-emphasis intended "redbook" Compact Discs, well de-emphasis sample rate. CS8414 monolithic CMOS device that receives decodes audio data kHz, according AES/EBU, IEC958, S/PDIF, EIAJ CP340/1201 interface standards. CS8414 receives data from transmission line, recovers clock synchronization signals, de-multiplexes audio digital data. CS8414 setup operate compatible mode. Microphone Line-In jacks connect left right ADC1 channel AD1836, depending setting jumpers. "MIC Gain Selection Jumpers (JP9-10)" page "ADC1 Input Selection Jumper (JP11)" page more information. jacks
ADSP-21161N EZ-KIT Lite Evaluation System Manual
Example Programs
connect ADC2 AD1836. This input configured though input mode selection jumpers, "ADC2 Input Mode Selection Jumpers (JP7-8)" page more information. Line-Out jacks connect left right outputs AD1836 AD1852. CS8414 includes error flag (VERF) indicate that audio output valid. This signal connects (LED9) board. This signal also used interpolation filters provide error correction.
Example Programs
Example programs provided with ADSP-21161N EZ-KIT Lite demonstrate various capabilities evaluation board. These programs installed with EZ-KIT Lite software found \.\VisualDSP Please refer readme file provided with each example more information.
Using Flash Programmer Utility
ADSP-21161N EZ-KIT Lite evaluation system includes Flash Programmer utility. utility allows program Flash memory EZ-KIT Lite. Flash Programmer installed with VisualDSP++. Once utility installed, accessible from Tools pull-down menu. more information Flash Programmer utility, select Start choose Programs->Analog Devices->VisualDSP++ 32-bit Processors->VisualDSP++ Documentation.
ADSP-21161N EZ-KIT Lite Evaluation System Manual
Using EZ-KIT Lite
Using EZ-KIT Lite VisualDSP++ Interface
This section provides information about following parts VisualDSP++ graphical user interface: "Boot Load" page "Target Options" page "Core Hang Conditions" page 2-11 "Hardware Breakpoints" page 2-12 "Restricted Software Breakpoints" page 2-19
Boot Load
Choosing Boot Load from Settings menu runs processor performs hard reset board. This command saves from having shut down VisualDSP++, reset EZ-KIT Lite board, bring VisualDSP++ again when want perform hard reset. this feature when loading debug boot code from external part when want device into known state.
Target Options
Choosing Target Options from Settings menu opens Target Options dialog (Figure 2-1). target options control certain aspects processor ADSP-21161N EZ-KIT Lite evaluation system.
ADSP-21161N EZ-KIT Lite Evaluation System Manual
Using EZ-KIT Lite VisualDSP++ Interface
Figure 2-1. Target Options Dialog While Target Halted Emulator Exit Options This target option controls processor's behavior when VisualDSP++ relinquishes control (for example, when exiting VisualDSP++). options detailed Table Table 2-5. Table 2-4. While Target Halted Options
Option Description
Stop Stops DMAs emulator space. This option disables requests when emulator control DSP. Data LINK, SPORT buffers held there unless internal request already granted. This option holds incoming data ceases outgoing data. Because SPORT-receive data cannot held off, lost, overrun set. direct write buffer (internal memory write) buffer allowed flush remaining data internal memory.
Other Options Table describes other available target options.
2-10
ADSP-21161N EZ-KIT Lite Evaluation System Manual
Using EZ-KIT Lite
Table 2-5. Emulator Exit Options
Option Emulator Exit Description Determines state left when emulator relinquishes control DSP: Reset causes reset begin execution from reset vector location. from current causes begin running from current location.
Table 2-6. Other Target Options
Option Reset before loading executable Verify writes target memory Description Resets registers before loading executable. Clear this option when registers must change their reset values when file load occurs. Validates memory writes DSP. After each write, read performed values checked matching condition. Enable this option during initial program development locate initial build problems (such attempting load data into non-existent memory). Clear this option increase performance while loading executable files since VisualDSP++ does perform extra reads that required verify each write. Resets cycle count registers zero before command issued. Select this option count number cycles executed between breakpoints program. Disables automatic configuration SDRAM registers (done through debugger).
Reset cycle counters Manual Extern configuration
Core Hang Conditions
Certain peripheral devices, such host ports, DMA, link ports, hold execution processor instructions. This known hung condition commonly occurs when reading from empty port writing full port. attempt halt processor made during these conditions, EZ-KIT Lite encounter core hang.
ADSP-21161N EZ-KIT Lite Evaluation System Manual
2-11
Using EZ-KIT Lite VisualDSP++ Interface
Normally, core hang cleared board using special clear/abort bit. However, there cases which desirable possible clear core hang. Sometimes desirable wait core hang clear itself, such when waiting host processor read write data. other cases, possible clear core hang, reset must occur continue debugging session. Table describes EZ-KIT Lite's core hang operations. Table 2-7. Core Hang Operations
Option Abort Retry Description Abort hung operation. This causes offending instruction aborted pipeline. Allows remedy hung operation. example, host processor holding DSP, cause host clear hung condition. Performs software reset target board. Aborts hung operation. This causes offending instruction aborted pipeline. Allows remedy hung operation. example, host processor holding DSP, cause host clear hung condition. Performs software reset target board.
Ignore Clear Acknowledge
Reset
Hardware Breakpoints
Hardware breakpoints work similarly watchpoints. hardware breakpoints Data transfers within user-defined memory range Instructions Register reads writes
2-12
ADSP-21161N EZ-KIT Lite Evaluation System Manual
Using EZ-KIT Lite
enable hardware breakpoints ADSP-21161N DSPs: From Settings menu, choose Hardware Breakpoints. Hardware Breakpoints dialog appears. dialog three tabbed pages: Data, Instruction, Other (Figure 2-2).
Figure 2-2. Hardware Breakpoints Dialog Refer following sections information about hardware breakpoints. "Common Hardware Breakpoint Attributes" page 2-13 "Global Hardware Breakpoint Options" page 2-13 "Data Hardware Breakpoints" page 2-15 "Instruction Hardware Breakpoints" page 2-16 "Other Breakpoints" page 2-17 "Tips Tricks Using Hardware Breakpoints" page 2-18 Common Hardware Breakpoint Attributes Each three tabs Hardware Breakpoints dialog common attributes. common attributes described Table 2-8. Global Hardware Breakpoint Options ADSP-21161N DSPs, options listed Table apply hardware breakpoints, regardless their type.
ADSP-21161N EZ-KIT Lite Evaluation System Manual
2-13
Using EZ-KIT Lite VisualDSP++ Interface
Table 2-8. Common Hardware Breakpoint Attributes
Attribute Enable Start Address Address Exclusive Mode Description Enables each individual breakpoint. Specify inclusive start addresses. Each pair addresses sets address range particular breakpoint. Enables breaks outside specified (inclusive) address range. Data page Other page only. This option specifies modes that trigger hardware breakpoints. available choices are: Disabled-disables breakpoint Write-triggers breakpoint write operation specified address range Read-triggers breakpoint read operation from specified address range Access-triggers breakpoint read write access specified address range.
Table 2-9. Global Hardware Breakpoint Options
Option Skip Breakpoint Events Description Specifies number breakpoint events ignored before stopping processor. Each time hardware breakpoint condition occurs, count decrements. When count reaches zero (0), processes hardware break. this option count number times break operation occurs. Breakpoints within group ORed together create this condition. Enables skip-count decrement specified Skip Breakpoint Events. Causes emulator restore Skip Count value program RESTART. Otherwise, Skip Count remains current value. ANDs interrupts form composite interrupt. Normally, group interrupts ORed create composite interrupt.
Restore Skip Count Break Restore Skip Count Break Breakpoints
2-14
ADSP-21161N EZ-KIT Lite Evaluation System Manual
Using EZ-KIT Lite
Data Hardware Breakpoints ADSP-21161N DSPs, data breakpoints break accesses internal memory, registers, external port (EP), multiprocessor memory space (MMS). following actions trigger data breakpoint:
DAG1 DM()
access modifier access
data breakpoints ORed generate single data breakpoint condition. Data page Hardware Breakpoints dialog box, which permits specification data breakpoints, shown Figure 2-3.
Figure 2-3. Data Page Hardware Breakpoints Dialog
ADSP-21161N EZ-KIT Lite Evaluation System Manual
2-15
Using EZ-KIT Lite VisualDSP++ Interface
Instruction Hardware Breakpoints ADSP-21161N DSPs, instruction breakpoint occurs when instruction executed within specified address ranges. four individual instruction breakpoints ORed generate single instruction breakpoint condition. Shown below Instruction page Hardware Breakpoints dialog box, which permits specification four individual instruction breakpoints.
Figure 2-4. Instruction Page Hardware Breakpoints Dialog
2-16
ADSP-21161N EZ-KIT Lite Evaluation System Manual
Using EZ-KIT Lite
Other Breakpoints SHARC DSPs, Other page Data Breakpoints dialog permits specification hardware breakpoints triggered access data, external port.
Figure 2-5. Other Page Hardware Breakpoints Dialog Table 2-10. Other Hardware Breakpoint Options
Option DataEvents Description Enables data breakpoints. data breakpoints similar data breakpoints (Data page), except accesses that trigger breakpoint made DAG2 PM() modifier. Like data breakpoints, data breakpoints cause break accesses internal memory, registers, external port (EP), multiprocessor memory space (MMS). Enables breakpoints. breakpoints triggered accesses made Address Bus. breakpoint break accesses made during transfers, accesses, Host accesses.
ADSP-21161N EZ-KIT Lite Evaluation System Manual
2-17
Using EZ-KIT Lite VisualDSP++ Interface
Table 2-10. Other Hardware Breakpoint Options (Cont'd)
Option External Port Description Enables external port breakpoints.External port (EP) breakpoints triggered accesses made through External Port. breakpoint break accesses made external device that tied such external memory. ANDs interrupts form composite interrupt. Normally, group interrupts ORed create composite interrupt.
Breakpoints
Tips Tricks Using Hardware Breakpoints aware following tips tricks when using hardware breakpoints ADSP-21161N processors. Latency SHARC processors, hardware breakpoints assert until instruction cycles after actual break condition occurs Restrictions When using hardware breakpoints, place breaks address where JUMP, CALL, IDLE instruction would illegal. place breaks last instructions LOOP delay slots delayed branch. more information these illegal locations, refer your DSP's Hardware Reference. Setting Breakpoint Single Address breakpoint single address, Start Address equal Address.
2-18
ADSP-21161N EZ-KIT Lite Evaluation System Manual
Using EZ-KIT Lite
Restricted Software Breakpoints
EZ-KIT Lite development system restricts breakpoint placement when certain conditions met. That under some conditions, breakpoints cannot placed effectively. Such conditions depend architecture, pipeline depth, ordering EZ-KIT Lite target processor.
ADSP-21161N EZ-KIT Lite Evaluation System Manual
2-19
Using EZ-KIT Lite VisualDSP++ Interface
2-20
ADSP-21161N EZ-KIT Lite Evaluation System Manual
EZ-KIT LITE HARDWARE REFERENCE
This chapter describes hardware design ADSP-21161N EZ-KIT Lite board. following topics covered. "System Architecture" page Describes configuration ADSP-21161N EZ-KIT Lite board explains board components interface with processor. "Jumper Settings" page Shows location describes function on-board jumpers. "LEDs Push Buttons" page 3-13 Shows location describes function LEDs push buttons. "Connectors" page 3-16 Shows location gives part number on-board connectors. Also, manufacturer part number information given mating parts. "Specifications" page 3-21 Provides board's measurements power supply specifications.
ADSP-21161N EZ-KIT Lite Evaluation System Manual
System Architecture
System Architecture
This section describes processor's configuration EZ-KIT Lite board.
Figure 3-1. System Architecture Block Diagram ADSP-21161N processor's core voltage 1.8V, external interface voltage 3.3V. through-hole oscillator supplies input clock processor. Footprints provided board surface-mount oscillator through-hole crystal alternate user-installed clocks. speed ADSP-21161N EZ-KIT Lite Evaluation System Manual
EZ-KIT Lite Hardware Reference
which core operates determined location clock mode jumper (JP21) described page 3-11. default, processor core runs MHz.
External Port
External Port (EP) processor connects 512K 8-bit Flash memory. Flash memory connects boot memory select (~BMS) memory select (~MS1) pin. connection allows Flash memory used boot processor well store information during normal operation. external memory interface also connects 48-bit SDRAM memory. SDRAM memory connects memory select (~MS0) pin. Refer "SDRAM Disable Jumper (JP1)" page information configure width SDRAM. Refer "Using SDRAM Memory" page summary processor's memory map. Some address, data, control signals available externally off-board connectors. connectors' pinout P10) found Appendix "Schematics".
Host Processor Interface (HPI)
Host Port Interface (HPI) signals brought unpopulated off-board connector (P9). This allows interface with user application. pinout host port connector found Appendix "Schematics".
SPORT Audio Interface
SPORT0
SPORT2 connected AD1836 codec (U10). stereo jack four mono jacks facilitate audio input, while stereo jack eight mono jacks facilitate audio output.
ADSP-21161N EZ-KIT Lite Evaluation System Manual
System Architecture
codec contains input channels. channel connects stereo jack jacks. stereo jack connects microphone. jacks connect LINE-OUT from audio device. supply audio input codec microphone input channel (MIC1) LINE_IN input channel. jumper settings JP11 determine whether LINE_IN channel codec driven connector connector.
Audio Interface
port connected AD1836 AD1852. port used writing reading control registers audio devices.
Breadboard AreUse breadboard area external circuitry board voltages grounds Package footprints: SOIC16 SOIC20 SOT23-6 PSOP44 SOT23 0805 Analog Devices does support responsible effects additional circuitry.
ADSP-21161N EZ-KIT Lite Evaluation System Manual
EZ-KIT Lite Hardware Reference
JTAG Emulation Port
JTAG emulation port allows emulator access processor's internal external memory, well special function registers, through 14-pin header. detailed description interface's connectors, EE-68 published Analog Devices website. more information, "JTAG Connector (P12)" page 3-19. more information about available emulators, contact Analog Devices (see "Product Information").
Jumper Settings
This section describes function jumpers. Figure shows locations jumpers.
SDRAM Disable Jumper (JP1)
jumper used enable disable third SDRAM device. When jumper installed, ADSP-21161N access SDRAM 48-bit-wide external memory. upper bits data multiplexed with Link Ports external data bus; therefore, when jumper installed, Link Ports available. Link Ports, jumper must removed.
SPDIF Selection Jumper (JP2)
jumper used select SPDIF input CS8414 digital audio receiver. When jumper configured optical connection, TOSLINK optical input connector (P4) should used. When jumper configured coax connection, input connector (P5) should used.
ADSP-21161N EZ-KIT Lite Evaluation System Manual
Jumper Settings
JP11: ADC1 Input Selector JP5: FLAG1 Enable JP1: External Memory Width JP22: Enable JP19: JP20: Boot Mode JP21: Clock Mode
JP26: Enable JP27: Enable JP4: FLAG0 Enable JP23: AD1836 Control Select JP6: Sample Frequency JP3: MCLK Select JP2: SPDIF Select JP9: Gain Right JP10: Gain Left JP7: ADC2 Input Mode Left JP8: ADC2 Input Mode Right
Figure 3-2. Jumper Locations
MCLK Selection Jumper (JP3)
jumper used select MCLK source AD1836 AD1852.
ADSP-21161N EZ-KIT Lite Evaluation System Manual
EZ-KIT Lite Hardware Reference
Table 3-1. SPDIF Modes
Jumper Location Mode Optical (factory default) Coax
Table 3-2. MCLK Selection
Jumper Location MCLK Source Audio Oscillator (12.288 MHz) (factory default) Derived clock from SPDIF Stream
FLAG0 Enable Jumper (JP4)
standard configuration, FLAG0 connected AD1836 used select port. This jumper should removed push button switch signal expansion connector (P10). Once jumper removed, longer communicate with AD1836.
FLAG1 Enable Jumper (JP5)
standard configuration, FLAG1 connected AD1852 used select port. jumper should removed push button switch signal expansion connector (P10). Once jumper removed, longer communicate with AD1852.
Sample Frequency Jumper (JP6)
jumper used select sample frequency AD1852 device. Table shows valid frequency modes.
ADSP-21161N EZ-KIT Lite Evaluation System Manual
Jumper Settings
Table 3-3. Sample Frequencies
Jumper Location None installed Sample Frequency allowed Interpolator) Interpolator) Interpolator) (factory default)
ADC2 Input Mode Selection Jumpers (JP7-8)
jumpers control input mode ADC2 AD1836 (see Table 3-4). high-performance mode, signal routed straight ADC. mode, signal goes through multiplexer programmable gain amplifier inside codec. Table 3-4. Input Mode
Jumper Location Input Mode (factory default) High Performance
Gain Selection Jumpers (JP9-10)
JP10 jumpers used select pre-amp gain microphone circuit (see Table 3-5). gain left right channel should configured same. Table 3-5. Gain
Jumper Position Installed Gain
ADSP-21161N EZ-KIT Lite Evaluation System Manual
EZ-KIT Lite Hardware Reference
Table 3-5. Gain (Cont'd)
Jumper Position Gain (factory default)
ADC1 Input Selection Jumper (JP11)
JP11 jumper used select input source ADC2. input source ADC2 LINE-IN, then connector should used. input source ADC2 microphone, then mini stereo plug should used. microphone used, gain circuit increased, described "MIC Gain Selection Jumpers (JP9-10)" page 3-8. When JP11 jumpers between pins between pins connection When jumpers between pins between pins connection jumper settings illustrated Table 3-6). (The words LINE board reference.) Table 3-6. Audio Input Jumper Settings
Microphone Input Stereo LINE_IN (Default)
JP11 LINE
JP11 LINE
ADSP-21161N EZ-KIT Lite Evaluation System Manual
Jumper Settings
Processor Jumper (JP19)
JP19 jumper used select different processor. During typical operation EZ-KIT Lite board, there only single system. jumper should single processor setting. When second processor attached board though link port, these jumpers should changed configure board processor other board processor System configuration options shown Table 3-7. Table 3-7. Processor Modes
Jumper Position Other Description Single processor (default) Processor Processor Invalid
Boot Mode Selection Jumper (JP20)
JP20 jumper determines ADSP-21161N processor boots. Table shows jumper setting boot modes. Table 3-8. Boot Mode Select Jumper (JP20) Settings
EBOOT Pins installed Installed Installed LBOOT Pins Installed Installed installed Pins installed (output) installed (input) Installed (input) Boot Mode EPROM BOOT (default) Host Processor Boot Serial Boot
3-10
ADSP-21161N EZ-KIT Lite Evaluation System Manual
EZ-KIT Lite Hardware Reference
Table 3-8. Boot Mode Select Jumper (JP20) Settings (Cont'd)
EBOOT Pins Installed Installed installed LBOOT Pins installed Installed installed Pins installed (input) Installed (input) Installed (input) Boot Mode Link Port Boot Boot Reserved
Clock Mode Selection Jumper (JP21)
JP21 jumper controls speed core external port ADSP-21161N processor. frequency supplied CLKIN changed removing oscillator (U24) that shipped with board replacing with different oscillator crystal (Y2). clock mode frequency should selected that minimum maximum specs ADSP-21161N processor exceeded. more information clock modes, ADSP-21161 SHARC Processor Hardware Reference. Table shows jumper setting clock modes. Table 3-9. Clock Mode Selections
CLKDBL Pins installed installed installed Installed Installed Installed CLK_CFG1 Pins Installed Installed installed Installed Installed installed CLK_CFG0 Pins Installed installed Installed Installed installed Installed Core Clock Ratio External Port Clock Ratio (default)
ADSP-21161N EZ-KIT Lite Evaluation System Manual
3-11
Jumper Settings
~BMS Enable Jumper (JP22)
JP22 jumper used control routing Boot Memory Select (~BMS) signal. When jumper installed, ~BMS signal routed Flash memory interface used reading, writing, booting. jumper should installed when using EPROM boot mode. jumper should removed when using serial boot no-boot mode. jumper remains "ON" serial boot no-boot modes, ~BMS signal grounded, flash memory selected.
AD1836 Control Selection Jumper (JP23)
AD1836 control registers programmed through port. port configured connected processor's port SPORT1. When jumper installed JP23, AD1836 port connected SPORT1 processor. When jumper removed, AD1836 port connects processor's port. default, jumper installed.
Enable Jumper (JP26)
push button attached though driver FLAG0 processor. disconnect driver from FLAG0 (for example, FLAG1 output), remove JP26.
Enable Jumper (JP27)
push button attached though driver FLAG1 processor. disconnect driver from (for example, FLAG1 output), remove JP27.
3-12
ADSP-21161N EZ-KIT Lite Evaluation System Manual
EZ-KIT Lite Hardware Reference
LEDs Push Buttons
This section describes functionality LEDs push buttons. Figure shows locations LEDs push buttons.
Monitor: VERF: Reset: Reset: Power: LED10 LED9 LED8 LED1 LED11
FLAG4-9: LED2
Reset: IRQ0-2: FLAG0-3:
SW5-7 SW1-4
Figure 3-3. Push Button Locations
ADSP-21161N EZ-KIT Lite Evaluation System Manual
3-13
LEDs Push Buttons
Reset LEDs (LED1 LED8)
When LED1 lit, master reset major active. When LED8 lit, ADSP-21161N processor (U1) being reset. interface resets processor during communication initialization.
FLAG LEDs (LED2-7)
FLAG LEDs connect processor's flag pins (FLAG4-9). LEDs active HIGH output from processor. Refer "LEDs Push Buttons" page 3-13 more information programmable flags program DSP. Table 3-10 shows FLAG signals corresponding LEDs. Table 3-10. FLAG LEDs
FLAG
FLAG4 FLAG5 FLAG6 FLAG7 FLAG8 FLAG9
Reference Designator
LED7 LED6 LED5 LED4 LED3 LED2
VERF (LED9)
VERF indicates that there possible error audio stream CS8414 digital receiver. error occur when digital audio cables disconnect from optical coaxial SPDIF connectors.
3-14
ADSP-21161N EZ-KIT Lite Evaluation System Manual
EZ-KIT Lite Hardware Reference
Monitor (LED10)
monitor (LED10) indicates that communication been initialized successfully, connect processor using VisualDSP++ EZ-KIT Lite session. does light, cycling power board and/or reinstalling driver (see "Installing EZ-KIT Lite Driver" page 1-6).
Power (LED11)
When LED11 (green), indicates that power being properly supplied board.
Programmable FLAG Push Buttons (SW1-4)
Four push buttons (SW1-4) provided general-purpose user input. push buttons connect processor's FLAG pins. push buttons active "HIGH" and, when pressed, send High processor. Refer "Using FLAG Pins" page more information. push button reference designators corresponding FLAGs summarized Table 3-11. Table 3-11. FLAG Switches
FLAG
FLAG0 FLAG1
Push Button Reference Designator
FLAG
FLAG2 FLAG3
Push Button Reference Designator
Interrupt Push Buttons (SW5-7)
Three push buttons provided general-purpose user interrupts. SW5- connect processor's programmable FLAG pins. push buttons active "HIGH" and, when pressed, send High
ADSP-21161N EZ-KIT Lite Evaluation System Manual
3-15
Connectors
processor. Refer "Using FLAG Pins" page more information. push button reference designators corresponding interrupt signals summarized Table 3-12. Table 3-12. Interrupt Switches
Interrupt Signal
IRQ0 IRQ1 IRQ2
Push Button Reference Designator
Board Reset Push Button (SW8)
RESET push button (SW8) resets board. During reset, interface automatically reinitialized. Pressing RESET push button (SW8) while VisualDSP++ running disrupts communication causes errors current debug session. VisualDSP++ must closed re-opened.
Connectors
This section describes connector functionality provides information about mating connectors. Figure shows connector locations.
Connector (P2)
connector (P2) standard Type receptacle.
3-16
ADSP-21161N EZ-KIT Lite Evaluation System Manual
EZ-KIT Lite Hardware Reference
Figure 3-4. Connector Locations
Part Description Type receptacle Manufacturer Mill-Max Digi-Key Part Number 897-30-004-90-000 ED90003-ND
Mating Connector (provided with EZ-KIT Lite) cable Assmann Digi-Key AK672-5 AK672-5ND
ADSP-21161N EZ-KIT Lite Evaluation System Manual
3-17
Connectors
Audio Connectors (P4-8, P17)
There stereo audio jacks, jacks, optical connector.
Part Description stereo jack P17) Jacks (P6) Jacks (P8) TORX (P4) Coaxial (P5) Manufacturer Shogyo SWITCHCRAFT SWITCHCRAFT TOSHIBA SWITCHCRAFT Mating Connectors 3.5mm stereo plug 3.5mm stereo cable P17) channel interconnect cable Digital Fiber-Optic Cable (P4) Digital Coaxial Cable (P5) Radio Shack Monster Cable Monster Cable Monster Cable L12-2397A BI100-1M ILS100-1M IDL100-1M Part Number SJ-0359AM-5 PJRAS2X2S01 PJRAS4X2U01 TORX173 PJRAN1X1U01
External Port Connector (P9)
40-pin 0.05' spacing connector provides access some processor's External Port signals. default, this connector populated.
Part Description 40-pin 0.05' (male) Manufacturer Samtec Mating Connector Female female cable Samtec FFSD-20-D-5.000-01-N Part Number FTSH-120-01-F-D-K
3-18
ADSP-21161N EZ-KIT Lite Evaluation System Manual
EZ-KIT Lite Hardware Reference
Host Processor Interface Connector (P10)
20-pin 0.05' spacing connector provides access some processor's External Port signals. default, this connector populated.
Part Description 20-pin 0.05' (male) Manufacturer Samtec Mating Connector Female female cable Samtec FFSD-10-D-5.000-01-N Part Number FTSH-110-01-F-D-K
JTAG Connector (P12)
JTAG header (P12) connecting point JTAG in-circuit emulator pod. When emulator connected JTAG header, debug interface disabled. missing provide keying. mating connector should have plug. When using emulator with EZ-KIT Lite board, follow connection instructions provided with emulator.
Part Description 14-pin Header (P12) Manufacturer Berg Part Number 54102-T08-07
Link Port Connectors (P13-14)
Each link port connected 26-pin connector. Refer EE-106 found website http://www.analog.com more information about link port connectors.
ADSP-21161N EZ-KIT Lite Evaluation System Manual
3-19
Connectors
Part Description position connector
Manufacturer Honda Mating Connector
Part Number RMCA-26JL-AD
Cable connector Shroud Coaxial cable
Honda Honda Gore
RMCA-E26F1S-A RMCA-E26L1A DXN2132
SPORT1 SPORT3 Connector (P15)
SPORT1
SPORT3 connected 20-pin connector.
Manufacturer Mating Connector Part Number 104069-1
Part Description position AMPMODU system receptacle
position AMPMODU system connector position AMPMODU system connector (w/o lock) Flexible film contacts connector)
2-487937-0 2-487938-0 487547-1
Power Connector (P16)
power connector (P16) provides power necessary operate EZ-KIT Lite board.
Part Description Power Jack (P16) Manufacturer SWITCHCRAFT Digi-Key Part Number RAPC712 SC1152-ND
3-20
ADSP-21161N EZ-KIT Lite Evaluation System Manual
EZ-KIT Lite Hardware Reference
Part Description
Manufacturer
Part Number
Mating Power Supply (shipped with EZ-KIT Lite) Power Supply Stack DTS070175SUDC-p6-SZ
Specifications
This section provides requirements powering board.
Power Supply
power connector supplies power EZ-KIT Lite board. Table 3-13 shows power supply specifications. Table 3-13. Power Supply Specifications
Terminal Center Outer Ring Connection +7V@2 amps
Board Current Measurements
ADSP-21161N EZ-KIT Lite board provides zero-ohm resistors that removed measure current draw. Table 3-14 shows resistor number, voltage plane, description components plane. Table 3-14. Current Measurement Resistors
Resistor R168 R169 Voltage Plane VDDINT VDDEXT Description Core Voltage Voltage
ADSP-21161N EZ-KIT Lite Evaluation System Manual
3-21
Specifications
3-22
ADSP-21161N EZ-KIT Lite Evaluation System Manual
BILL MATERIALS
Manufacturer
Description
Reference
Reference Design
Quantity
M29W040 PLCC32 FLASH-512K-X-8-3V
MICRO
M29W040B120K6 74LVC14AD
74LVC14A SOIC14 U21-22 HEX-INVER-SCHMITT-T RIGGER MT48LC1M16A1TG U2-4 TSOP50 1MX16-SDRAM-143MHZ CS8414 SOIC28 96KHZ-DIGITAL-AUDIO-RECVR
MICRON
MT48LC1M16A1TG-7S
CIRRUS LOGIC CYPRESS
CS8414
CY7C64603-128 PQFP128 USB-TX/RX MICROCONTROLLER MMBT4124 SOT-23 TRANSISTOR MMBT4401 SOT-23 TRANSISTOR 200MA 74LVC00AD SOIC14 CY7C1019BV33-15VC SOJ32 128K SRAM
CY7C64603-128NC
FAIRCHILD FAIRCHILD
MMBT4124 MMBT4401
PHILIPS CYPRESS
74LVC00AD CY7C1019BV33-12VC
ADSP-21161N EZ-KIT Lite Evaluation System Manual
Part Number
Manufacturer
Description
Reference
Reference Design
Quantity
AD8532AR SOIC8 DUAL 250MA 12.288MHZ OSC001 SN74AHC1G02 SOT23-5 SINGLE-2 INPUT-NOR
U34,U37
ANALOG DEVICES DIG01 CYPRESS DIGI-KEY DIG01 MICROCHIP
AD8532AR SG-8002DC-PCC-ND 12.288MH SN74AHC1G02DBVR SN74LV164AD CY7C4201V-15AC SG-8002DC-PCC-ND 300-6027-ND 24LC00-SN 12065A102JAT2A 12065A222JAT050
SN74LV164A SOIC14 8-BIT-PARALLEL-SERIAL CY7C4201V-15AC TQFP32 64-BYTE-FIFO 25MHZ OSC01 12.0MHZ OSC006 CRYSTAL 21161 24LC00 U7"" 1000127 1000pF 1206 CERM 2200pF 1206 C85-86 C40, C46, C52, C58, C64, C70, C76,
ADM708SAR SOIC8 VOLTAGE-SUPERVISOR AD1852 SSOP28 MULTIBIT-SIGMA-DELTA-DAC AD1836AS MQFP52 MULTI-CHANNEL-96KHZ-CODEC
ANALOG DEVICES ANALOG DEVICES ANALOG DEVICES
ADM708SAR AD1852JRS
AD1836AS
ADSP-21161N EZ-KIT Lite Evaluation System Manual
Part Number
Bill Materials
Manufacturer
Description
Reference
Reference Design
Quantity
ADSP-21161NKCA100 PBGA225 SPACING REV. X1.2 ADP3338AKC-33 SOT-223 3.3V-1.0AMP REGULATOR ADP3339AKC-5 SOT-223 5V-1.5A REGULATOR VR1,
ANALOG DEVICES ANALOG DEVICES ANALOG DEVICES ANALOG DEVICES
ADSP-21161NCCA100
ADP3338AKC-3.3
ADP3339AKC-5-REEL ADP3338AKC-1.8 LMV722M TAJC475K025R SC1152-ND12
ADP3338AKC-18 SOT-223 1.8V-1A REGULATOR
LMV722M SOIC8 DUAL AUDIO 4.7uF TANT 2.5MM_JACK CON005 4PIN CON009
U12-20, NATIONAL SEMI CT23-25 SWITCHCRAFT MILL-MAX TOSHIBA
897-30-004-90-000000 TORX173
TORX173 6PIN CON008 FIBER OPTIC MODULE CON011 CON012 CON013 LNKPRT 12X2 CON010 P13-14
SWITCHCRAFT SWITCHCRAFT SWITCHCRAFT HONDA (TSUSHINK)
PJRAS4X2U01 PJRAN1X1U01 PJRAS2X2S01 RMCA-EA26LMY-0M03-A
ADSP-21161N EZ-KIT Lite Evaluation System Manual
Part Number
Manufacturer
Description
Reference
Reference Design
Quantity
10X2 CON014 SPST-MOMENTARY SWT013 DIP8 SWT016 1/8W 1206 0.00 1/8W 1206
SW1-8
PANASONIC
104069-1 EVQ-PAD04M
R153, R154, R168-169, R217, R218 LED2-7, LED9-10 C36, C42, C48, C54, C60, C66, C72, C6-7, C91-149, C154-155, C165-171, C184-C186, C174-179 C156-164, C172, C183
PANASONIC YAGEO
CKN1365-ND P10ECT-ND 0.0ECT-ND
AMBER-SMT LED001 GULL-WING 330pF
PANASONIC
LN1461C-TR 08055A331JAT
0.01uF 100V CERM
08051C103KAT2A
0.22uF CERM 0.1uF CERM
08053C224FAT 08055C104KAT
C1,C5,C9-11, C33,C87-90, C150-153, C173,C180
ADSP-21161N EZ-KIT Lite Evaluation System Manual
Part Number
Bill Materials
Manufacturer
Description
Reference
Reference Design
Quantity
0.001uF
C14-15, C19-20, C24-25, C29-30 CT19-22, CT36
08055A102JAT2A
10uF TANT
SPRAGUE
293D106X9025C2T CR21-103J-T
100MW
R3-4,R6,R13, R15,R17-20, R124,R126,R 128,R130, R132,R134, R136, R148-149, R151, R155-164, R175, R177-181, R183,R190, R171,R172, R174, R185-187, R193-194, R219-220 R150, R176, R152 R184, R188, R189, R191, R165 R137-147
100MW 4.7K 100MW
CR21-330JTR CR21-4701F-T
100MW 100MW
CR21-6800F-T CR21-1004F-T
ADSP-21161N EZ-KIT Lite Evaluation System Manual
Part Number
Manufacturer
Description
Reference
Reference Design
Quantity
100MW 1.5K 100MW 2.00K 1/8W 1206
R49-50 R66, R74, R82, R90, R98, R106, R114, R122, R192, R206 R10-11
DALE
CR21-471J-T CR21-1501F-T CRCW1206-2001FRT1 CR32-4992F-T
49.9K 1/8W 1206
2.21K 1/8W 1206
CR32-2211F-T 12061A101JAT2A
100pF 100V 1206
C12, C16-17, C21-22, C26-27, C31, C35, C38, C41, C44, C47, C50, C53, C56, C59, C62, C65, C68, C71, C74, C80, CT1-4, CT11 R216 R123, R125, R127, R129, R131, R133, R135
10uF TANT 100MW 100MW
TAJB106K016R CR21-223J-T CR21-101J-T
ADSP-21161N EZ-KIT Lite Evaluation System Manual
Part Number
Bill Materials
Manufacturer
Description
Reference
Reference Design
Quantity
220pf 1206
C39, C45, C51, C57, C63, C69, C75, FER13
12061A221JAT2A
1000 100MHZ 1.5A FER002 0.06 CHOKE
MURATA
PLM250S40T1
S2A_RECT DO-214AA D1-2 SILICON RECTIFIER
GENERALSEMI DIGI-KEY
240-1019-1-ND P11.0FCT-ND
100MHZ 500MA 1206 FER1-11 0.70 BEAD 1/8W 1206 R23, R27, R30, R34, R40-41, R47-48 R25, R32, R38,
750K 1/8W 1206
RK73H2BT7503F CRCW12065761FRT1
5.76K 1/8W 1206
R21, R22, DALE R24, R26, R28-29, R31, R33, R35-37, R39, R42-44, R59, R67, R75, R83, R91, R99, R107, R115 C13, C18, C23, C28, C187-190 DALE
11.0K 1/8W 1206
CRCW12061102FTR1
68NF 120PF 1206
MURRATA PHILLIPS
GRM40X7R683K050AL 1206CG121J9B200
ADSP-21161N EZ-KIT Lite Evaluation System Manual
Part Number
Manufacturer
Description
Reference
Reference Design
Quantity
1/8W 1206 820PF 100V 1206 30PF 100V 1206 680PF
C32, C3-4 C37, C43, C49, C55, C61, C67, C73, R63, R71, R79, R87, R95, R103, R111, R119 R60, R61, R68, R69, R76, R77, R84, R85, R92, R93, R100, R101, R108, R109, R116, R117 R62, R70, R78, R86, R94, R102, R110, R118 R54, R64, R72, R80, R88, R96, R104, R112, R120
PHILIPS
9C12063A75R0JLRT/R 12061A821KAT2A 12061A300JAT2A 08055A681FAT2A
2.74K 1/8W 1206
PANASONIC
ERJ-8ENF2741V
5.49K 1/8W 1206
PANASONIC
ERJ-8ENF5491V
3.32K 1/8W 1206
PANASONIC
ERJ-8ENF3321V
1/8W 1206 1.65K 1/8W 1206
PANASONIC PANASONIC
ERJ-8ENF1000V ERJ-8ENF1651V
ADSP-21161N EZ-KIT Lite Evaluation System Manual
Part Number
Bill Materials
Manufacturer
Description
Reference
Reference Design
Quantity
10UF CAP002 ELEC
CT5-10 CT26-35 RN1-2 R167 R53, R170,R173 R8-9
DIG01 PANASONIC GENERAL SEMI DALE DALE CYPRESS
PCE3062TR-ND EEV-FC1E680P SL22 767-161-103G CR32-102J-T CR1206-1003FTR1
68UF CAP003 ELEC SL22 DO-214AA SCHOTTKY 100MW RNET16 BUSSED 1/8W 1206 100K 1/8W 1206 1.00K 1/8W 1206 20.0K 1/8W 1206 1/8W 1206 74FCT244AT QSOP20 OCTAL-BUFFER 10.0K 1/8W 1206 RED-SMT LED001 GULL-WING GREEN-SMT LED001 GULL-WING 1/8W 1206
CRCW1206-2002FRT1
CY74FCT244ATQC CRCW1206-1002FRT1 LN1261C LN1361C ERJ-8ENF6040V
R51-52, R55, DALE LED1, LED8 PANASONIC LED11 R65, R73, R81, R89, R97, R105, R113, R121 PANASONIC PANASONIC
ADSP-21161N EZ-KIT Lite Evaluation System Manual
Part Number
Manufacturer
Description
Reference
Reference Design
Quantity
TANT -55+125 ADG774A QSOP16 QUICKSWITCH-257 IDC2X1 IDC3X1 IDC4X1 IDC2X2 0.1x0.1 IDC3X2 IDC7X2 HEADER
CT12-18 U31.U35, JP1, JP4-5, JP22-23, JP26, JP27
PANASONIC ANALOG DEVICES BERG
ECS-T1EY105R ADG774ABRQ 54101-T08-02
JP2-3, JP9-10 BERG JP7-8, JP11, JP19-21 BERG SULLINS BERG BERG RAYCHEM CORP. SHOGYO
54101-T08-03 54102-T08-02 PTC02DAAN 54102-T08-03 54102-T08-07 SMD250-2 SJ-0359AM-5
2.5A RESETABLE FUS001 3.5MM STEREO_JACK CON001
A-10
ADSP-21161N EZ-KIT Lite Evaluation System Manual
Part Number
ADSP-21161 EZ-KIT LITE Schematic
ANALOG DEVICES
Approvals
Drawn Checked Engineering
Cotton Road Nashua, 03063
Date
Title Size
21161N EZ-KIT LITE TITLE PAGE
Board
Date
11-13-2003_11:40
A0157-2000
Sheet
A[0:21] ADDR0 ADDR1 ADDR2 ADDR3 ADDR4 ADDR5 ADDR6 ADDR7 ADDR8 ADDR9 ADDR10 ADDR11 ADDR12 ADDR13 ADDR14 ADDR15 ADDR16 ADDR17 ADDR18 ADDR19 ADDR20 ADDR21 ADDR22 ADDR23 DATA16 DATA17 DATA18 DATA19 DATA20 DATA21 DATA22 DATA23 DATA24 DATA25 DATA26 DATA27 DATA28 DATA29 DATA30 DATA31 DATA32 DATA33 DATA34 DATA35 DATA36 DATA37 DATA38 DATA39 DATA40 DATA41 DATA42 DATA43 DATA44 DATA45 SDCKE SDCLK0 SDWE SDA10 SDCKE SDCLK0 SDCLK1 SDWE SDA10 TRST CLKIN XTAL TRST CLK_CFG0 CLK_CFG1 BRST DSP_RESET DSP_AVDD BRST RESET AVDD BMSTR AGND ADSP-21161N-100 PBGA225 RPBA TIMEXP TIMEXP DMAG2 BMSTR DMAR2 DMAR1 IDC1X1 CLKDBL CLKIN XTAL CLK_CFG0 CLK_CFG1 CLKDBL CLKOUT SBTS DMAG1 DMAG1 DMAR1 SBTS AGND DATA46 DATA47 L0D2 L0D3 L0D4 L0D5 L0D6 L0D7 L1D2 L1D3 L1D4 L1D5 L1D6 L1D7 FLAG1 FLAG2 FLAG3 FLAG4 FLAG5 FLAG6 FLAG7 FLAG8 FLAG9 FLAG[0:9] FLAG0 L1ACK L1CLK L1D[0:7] L1D0 L1D1 L1ACK L1CLK L1DAT0 L1DAT1 L1DAT2 L1DAT3 L1DAT4 L1DAT5 L1DAT6 L1DAT7 MISO MOSI SPIDS SPICLK MISO MOSI IRQ2 SPIDS SPICLK IRQ0 IRQ1 IRQ2 SPIDS IRQ0 IRQ1 IRQ2 REDY IRQ0 REDY VDDINT 0.1UF 0.01UF 1206 DSP_AVDD RNET16 IRQ1 SCLK3 BRST SCLK3 SFS3 SD3A SD3B 3.3V RNET16 D[16:47] L0ACK L0CLK L0D[0:7] L0D0 L0D1 L0ACK L0CLK L0DAT0 L0DAT1 L0DAT2 L0DAT3 L0DAT4 L0DAT5 L0DAT6 L0DAT7 SCLK2 DMAR1 DMAR2 SD2A REDY SCLK1 SCLK1 SFS1 SD1A SD1B DMAG1 DMAG2 SBTS SCLK0 SCLK0 SFS0 SD0A 3.3V SFS1 SD1A SD1B
SFS0 SD0A SD0B
SFS2 SD2A SD2B
SFS3 SD3A SD3B
FLAG0 FLAG1 FLAG2 FLAG3 FLAG4 FLAG5 FLAG6 FLAG7 FLAG8 FLAG9 FLAG10 FLAG11
DMAG2 DMAR2 ADSP-21161N-100 PBGA225
EBOOT LBOOT
EBOOT LBOOT
ANALOG DEVICES
Approvals
Drawn Checked Engineering
Cotton Road Nashua, 03063
Date
Title Size Board
21161N EZ-KIT LITE
Date
11-12-2002_17:09
A0157-2000
Sheet
AGND
A[0:14] D[16:47]
DQ10 DQ11 DQ12 DQ13 DQ14 DQ15
DQ10 DQ11 DQ12 DQ13 DQ14 DQ15
L0D0 L0D1 L0D2 L0D3 L0D4 L0D5 L0D6 L0D7 L1D0 L1D1 L1D2 L1D3 L1D4 L1D5 L1D6 L1D7 L1D[0:7] L0D[0:7]
DQ10 DQ11 DQ12 DQ13 DQ14 DQ15
DQML DQMH
DQML DQMH
DQML DQMH
MT48LC1M16A1TG TSOP50 MT48LC1M16A1TG TSOP50
MT48LC1M16A1TG TSOP50
SDA10 SDWE SDCLK0 SDCKE
SDRAM
SDRAM
SDRAM
3.3V
INSTALL JUMPER MEMORY REMOVE JUMPER LINK PORTS
IDC2X1
SHORTING JUMPER DEFAULT=INSTALLED
ANALOG DEVICES
Approvals
Drawn Checked Engineering
Cotton Road Nashua, 03063
Date
Title Size
21161N EZ-KIT LITE SDRAM
Board
Date
11-12-2002_17:09
A0157-2000
Sheet
A[0:18] 3.3V R175 JP22 IDC2X1 74LVC00AD SOIC14 74LVC14A SOIC14 INSTALL JUMPER READ/WRITE BOOT FROM FLASH REMOVE JUMPER WHEN USING BOOT MODE SJ32 SHORTING JUMPER DEFAULT=INSTALLED M29W040B PLCC32RS D[16:23]
FLASH 512K
ANALOG DEVICES
Approvals
Drawn Checked Engineering
Cotton Road Nashua, 03063
Date
Title Size
21161N EZ-KIT LITE FLASH SRAM
Board
Date
2-19-2004_15:44
A0157-2000
Sheet
3.3V
R184 4.7K
R188 4.7K
R189 4.7K
R191 4.7K
3.3V USB_TMS USB_TCK R187 USB_TRST USB_TDI R165 4.7K TRST
QS3257Q QSOP16 IDC7X2 USB_EMU
JTAG HEADER
SHOULD
QS3257Q QSOP16
JTAG HEADER CIRCUIT EZ-KIT LITE ONLY REFER EE-68 STANDARD JTAG HEADER CONNECTION. THIS FOUND HTTP://WWW.ANALOG.COM
ANALOG DEVICES
Approvals
Drawn Checked Engineering
Cotton Road Nashua, 03063
Date
Title Size
21161N EZ-KIT LITE JTAG INTERFACE
Board
Date
A0157-2000
Sheet
DSDATA2 FER2 1206 0.1UF 0.01UF DLRCLK DBCLK SDATA FSYNC R176 AUDIO_OSC MCLK IDC3X1 SHORTING JUMPER DEFAULT=2&3
MCLK SOURCE AD1836 AD1852
INSTALL JUMPER AUDIO OSCILALTOR INSTALL JUMPER CS8414
VERF
VERF
C0~/E0
CA/E1 CB/E2 CC/F0 CD/F1 CE/F2
TOSLINK OPTICAL INPUT
VCC1 OUT2 GND4 GND5 SHIELD6 SHIELD TORX173 CON008
IDC3X1
SHORTING JUMPER DEFAULT=1&2
74LVC00AD SOIC14 0.01UF 68NF
FILT CS12/FCK CS8414 SOIC28
OPERATING COMPATIBLE MODE
PLACE JUMPER OPTICAL INPUT PLACE JUMPER COAX INPUT
74LVC00AD SOIC14
DIGITAL AUDIO RECEIVER
SPDIF COAX INPUT
CON012 AGND
1206
ANALOG DEVICES
Approvals
Drawn Checked Engineering
Cotton Road Nashua, 03063
Date
Title Size
21161N EZ-KIT LITE AUDIO RECEIVER
Board
Date
12-9-2003_21:30
A0157-2000
Sheet
INSTALL JUMPER CONNECT CODEC PORT (JP12 JP13 INSTALLED) REMOVE JUMPER FLAG0 PUSH BUTTON EXPANSION HEADER ODVDD CONNECTED 3.3V 3.3V SD0A ASDATA2 SFS0 SCLK0 R219 ASDATA1 ASDATA2 ALRCLK ABCLK OUT1R+ OUT1RMCLK MCLK OUT2L+ CLATCH_C SPICLK_C MOSI_C MISO_C CLATCH CCLK CDATA COUT OUT2R+ OUT2R33 OUT2R+ OUT2ROUT2L6 OUT2L+ OUT2L31 OUT1R+ OUT1ROUT1L+ OUT1L8 OUT1L+ OUT1L3.3V
DAC1 LEFT
SHORTING JUMPER DEFAULT=1&2
DAC1 RIGHT
SHORTING JUMPER DEFAULT=3&4
R220
IDC2X2
SAMPLE FREQUENCY
ALLOWED SHORTEDNOT SHORTED 192kHz INTERPOLATOR) SHORTEDSHORTED 96kHz INTERPOLATOR) SHORTED SHORTED 48kHz INTERPOLATOR) SHORTED SHORTED
DAC2 LEFT DAC2 RIGHT
ADC1 LEFT
IN1L+ IN1L-
IN1L+ IN1L-
OUT3L+ OUT3L-
OUT3L+ OUT3L-
DAC3 LEFT DAC3 RIGHT
MCLK DBCLK DLRCLK
96/48~ 192/48~
OUTL+
OUT4L+ OUT4L-
OUTL-
DAC4 LEFT DAC4 RIGHT
ADC1 RIGHT
IN1R+ IN1R-
IN1R+ IN1R-
OUT3R+ OUT3R-
OUT3R+ OUT3R-
IN2L+
IN2L+/CL2/CL2 IN2L-/CL1/CL1 NC/IN2L1/IN2L+ NC/IN2L2/IN2L-
DSDATA1 DSDATA2 DSDATA3 DLRCLK DBCLK
SD2A DSDATA2 IDC2X1
ASDATA2
MCLK BCLK LRCLK SDATA
OUTR+ OUTR-
OUT4R+ OUT4R-
ADC2 LEFT
IN2LIN2L1 IN2L2
FILTR FILTB
SPICLK
DLRCLK DBCLK
SHORTING JUMPER DEFAULT=INSTALLED
MOSI
CCLK CLATCH CDATA
ZEROL ZEROR
IN2R2
NC/IN2R2/IN2RNC/IN2R1/IN2R+ IN2R-/CR1/CR1 IN2R+/CR2/CR2 FILTR FILTD 10UF 0.1UF 10UF 0.1UF FLAG1
ADC2 RIGHT
IN2R1 IN2RIN2R+
RESET
10UF
0.1UF
10UF
FLAG0 SHORTING JUMPER DEFAULT=INSTALLED 3.3V SFS1 IDC2X1 SCLK1 SPICLK R190 SD3A MOSI SD1A MISO JP23 IDC2X1 QS3257Q QSOP16
PD/RST AD1836AAS MQFP52
R164
DEEMP MUTE
IDPM0 IDPM1
CODEC
AGND R170 20.0K 1206 VREF AD1852 SSOP28
CLATCH_C
INSTALL JUMPER CONNECT PORT (JP12 JP13 INSTALLED) REMOVE JUMPER FLAG1 PUSH BUTTON EXPANSION HEADER SSM2275 SOIC8
SPICLK_C
SSM2275 SOIC8
MOSI_C R173 20.0K 1206 AGND R154 0.00 1206
MISO_C
ANALOG DEVICES
Approvals
Drawn Checked Engineering
Cotton Road Nashua, 03063
R153 0.00 1206
Date
Title Size
21161N EZ-KIT LITE CODEC
Board
Date
2-19-2004_14:44
A0157-2000
Sheet
CON013 LOOP_ADC1_LEFT 120PF 1206 FER3 1206 10UF CAP002 5.76K 1206 5.76K 1206
100PF 1206
AGND AGND VREF
1206 IN1L-
SSM2275 SOIC8 5.76K 1206 5.76K 1206
0.001UF 100PF 1206
ADC1 LEFT
C187 120PF 1206 AGND 750K 1206 1206 SSM2275 SOIC8 IN1L+ 0.001UF
AGND CON013 LOOP_ADC1_RIGHT 120PF 1206 FER4 1206 10UF CAP002 5.76K 1206 5.76K 1206
100PF 1206
AGND AGND SSM2275 SOIC8 5.76K 1206 5.76K 1206 0.001UF 100PF 1206 1206 IN1R-
ADC1 RIGHT
C188 120PF 1206 AGND 750K 1206 1206 SSM2275 SOIC8 IN1R+ 0.001UF
ANALOG DEVICES
Approvals Date
Title Size Board
Cotton Road Nashua, 03063
21161N EZ-KIT LITE PRIMARY INPUT
Drawn Checked
AGND
Date
11-12-2002_17:10
A0157-2000
Sheet
Engineering
CON013 LOOP_ADC2_LEFT 100PF 1206 120PF 1206 FER5 1206 10UF CAP002 5.76K 1206 5.76K 1206
SHORTING JUMPER DEFAULT=1&3
ADC2 LEFT INPUT MODE
MODE HIGH PERFORMANCEMODE
SHORTING JUMPER DEFAULT=2&4
AGND AGND VREF
1206
IN2L2 IN2L-
SSM2275 SOIC8 5.76K 1206 5.76K 1206 C189 120PF 1206 750K 1206 IDC3X2 0.001UF SSM2275 SOIC8 1206 IN2L+ IN2L1LINE AGND 0.001UF 100PF 1206
ADC2 LEFT
AGND CON013 LOOP_ADC2_RIGHT 100PF 1206 120PF 1206 FER6 1206 10UF CAP002 5.76K 1206 5.76K 1206
SJ10 SHORTING JUMPER DEFAULT=1&3 SJ11 SHORTING JUMPER DEFAULT=2&4
ADC2 RIGHT INPUT MODE
MODE HIGH PERFORMANCEMODE
JP11 SHEET SHOULD LINE POSITION EITHER THESE MODES
AGND AGND
1206
IN2R2 IN2R3
SSM2275 SOIC8 5.76K 1206 5.76K 1206 C190 120PF 1206 750K 1206
IDC3X2
0.001UF 100PF 1206 0.001UF
ADC2 RIGHT
1206
AGND
SSM2275 SOIC8
IN2R+ IN2R1LINE
ANALOG DEVICES
Date
Title Size Board
Cotton Road Nashua, 03063
Approvals
AGND
21161N EZ-KIT LITE SECONDARY INPUT
Drawn Checked Engineering
Date
11-12-2002_17:11
A0157-2000
Sheet
GAIN IDC3X1 1.00K 1206 1206 SJ12 SHORTING JUMPER DEFAULT=1&2 20dB 40dB NONE
820PF 1206
10.0K 1206 AVCC SJ13 SSM2275 SOIC8 2.00K 1206 CON001 2.00K 1206 CT11 10UF 0.1UF MMBT4124 SOT-23 10.0K 1206 SJ14 SHORTING JUMPER DEFAULT=4&6 SHORTING JUMPER DEFAULT=3&5
FER7 1206
10UF CAP002
IN2R1 IN2R1LINE VREF JP11 IDC3X2
ADC2 RIGHT/LEFT
IN2L1LINE
INPUT
FER8 1206
10.0K 1206 CT10 10UF CAP002 AGND AGND
IN2L1
AGND
SSM2275 SOIC8
ADC2 INPUT SELECTOR
INSTALL JUMPERS LINE INSTALL JUMPERS
10.0K 1206
820PF 1206
1.00K 1206
1206 JP10
GAIN SJ15 SHORTING JUMPER DEFAULT=1&2 20dB 40dB NONE
IDC3X1
ANALOG DEVICES
Approvals
Drawn Checked Engineering
Cotton Road Nashua, 03063
Date
Title Size
21161N EZ-KIT LITE INPUT
Board
Date
2-19-2004_14:44
A0157-2000
Sheet
DAC1_RIGHT
CT34 68UF CAP003
AD8532AR SOIC8
R206 49.9K 1206 AGND CON001 CT35 68UF CAP003 AGND R192 49.9K 1206
DAC1_LEFT
AD8532AR SOIC8
AGND
ANALOG DEVICES
Approvals
Drawn Checked Engineering
Cotton Road Nashua, 03063
Date
Title 21161N Size
EZ-KIT LITE DAC1 OUTPUT-STEREO JACK
Board
Date
A0157-2000
Sheet
DAC1_LEFT
5.49K 1206 11.0K 1206 OUT1LR62 3.32K 1206
100PF 1206
330PF 5.49K 1206 OUT1L+ 680PF 1.65K 1206 SSM2275 SOIC8 2200PF 1206 49.9K 1206 1206 CT26 68UF CAP003 LOOP_DAC1_LEFT CON011
DAC1 LEFT
100PF 1206
2.74K 1206
220PF 1206 AGND
VREF
AGND
DAC1_RIGHT
5.49K 1206 11.0K 1206 OUT1RR70 3.32K 1206
100PF 1206
330PF 5.49K 1206 680PF 1.65K 1206 SSM2275 SOIC8 2200PF 1206 49.9K 1206 1206 CT27 68UF CAP003 LOOP_DAC1_RIGHT CON011
DAC1 RIGHT
100PF 1206
OUT1R+
2.74K 1206
220PF 1206 AGND
ANALOG DEVICES
Date
Title Size Board
Cotton Road Nashua, 03063
Approvals
Drawn
AGND
21161N EZ-KIT LITE DAC1 OUTPUT
Checked Engineering
Date
11-12-2002_17:12
A0157-2000
Sheet
5.49K 1206 11.0K 1206 OUT2LR78 3.32K 1206
100PF 1206
330PF 5.49K 1206 OUT2L+ 680PF 1.65K 1206 SSM2275 SOIC8 2200PF 1206 49.9K 1206 1206 CT28 68UF CAP003 LOOP_DAC2_LEFT CON011
DAC2 LEFT
100PF 1206
2.74K 1206
220PF 1206 AGND
VREF
AGND
5.49K 1206 11.0K 1206 OUT2RR86 3.32K 1206
100PF 1206
330PF 5.49K 1206 680PF 1.65K 1206 SSM2275 SOIC8 2200PF 1206 49.9K 1206 1206 CT29 68UF CAP003 LOOP_DAC2_RIGHT CON011
DAC2 RIGHT
100PF 1206
OUT2R+
2.74K 1206
220PF 1206 AGND
ANALOG DEVICES
Date
Title Size Board
Cotton Road Nashua, 03063
Approvals
Drawn
AGND
21161N EZ-KIT LITE DAC2 OUTPUT
Checked Engineering
Date
11-12-2002_17:12
A0157-2000
Sheet
5.49K 1206 11.0K 1206 OUT3LR94 3.32K 1206
100PF 1206
330PF 5.49K 1206 OUT3L+ 680PF 1.65K 1206 SSM2275 SOIC8 2200PF 1206 49.9K 1206 1206 CT30 68UF CAP003 LOOP_DAC3_LEFT CON011
DAC3 LEFT
100PF 1206
2.74K 1206
220PF 1206 AGND
VREF
AGND
R101 5.49K 1206 11.0K 1206 OUT3RR102 3.32K 1206
100PF 1206
330PF R100 5.49K 1206 680PF R104 1.65K 1206 SSM2275 SOIC8 2200PF 1206 R106 49.9K 1206 R105 1206 CT31 68UF CAP003 LOOP_DAC3_RIGHT CON011
DAC3 RIGHT
100PF 1206
OUT3R+
R103 2.74K 1206
220PF 1206 AGND
ANALOG DEVICES
Date
Title Size Board
Cotton Road Nashua, 03063
Approvals
Drawn
AGND
21161N EZ-KIT LITE DAC3 OUTPUT
Checked Engineering
Date
11-12-2002_17:12
A0157-2000
Sheet
R109 5.49K 1206 R107 11.0K 1206 OUT4LR110 3.32K 1206
100PF 1206
330PF R108 5.49K 1206 OUT4L+ 680PF R112 1.65K 1206 SSM2275 SOIC8 2200PF 1206 R114 49.9K 1206 R113 1206 CT32 68UF CAP003 LOOP_DAC4_LEFT CON011
DAC4 LEFT
100PF 1206
R111 2.74K 1206
220PF 1206
AGND VREF
AGND
R117 5.49K 1206 R115 11.0K 1206 OUT4RR118 3.32K 1206
100PF 1206
330PF R116 5.49K 1206 680PF R120 1.65K 1206 SSM2275 SOIC8 2200PF 1206 R122 49.9K 1206 R121 1206 CT33 68UF CAP003 LOOP_DAC4_RIGHT CON011
DAC4 RIGHT
100PF 1206
OUT4R+
R119 2.74K 1206
220PF 1206 AGND
ANALOG DEVICES
Date
Title Size Board
Cotton Road Nashua, 03063
Approvals
Drawn
AGND
21161N EZ-KIT LITE DAC4 OUTPUT
Checked Engineering
Date
11-12-2002_17:12
A0157-2000
Sheet
3.3V
3.3V
EXFLAG0 R123 SWT013 SPST-MOMENTARY R124 CT12 74LVC14A SOIC14 IDC2X1 SJ16 SHORTING JUMPER DEFAULT=1 JP26 FLAG0 SWT013 SPST-MOMENTARY CT15 EXFLAG3 R129 R130 74LVC14A SOIC14 FLAG3
3.3V
3.3V
3.3V
R132 EXFLAG1 R125 SWT013 SPST-MOMENTARY R126 CT13 74LVC14A SOIC14 IDC2X1 SJ17 SHORTING JUMPER DEFAULT=1 JP27 FLAG1 SWT013 SPST-MOMENTARY CT16 EXIRQ0 R131 74LVC14A SOIC14 EXIRQ2 R135 IRQ0 SWT013 SPST-MOMENTARY
R136
CT18 74LVC14A SOIC14
IRQ2
74LVC14A SOIC14
74LVC14A SOIC14
3.3V
3.3V
R134 EXFLAG2 R127 SWT013 SPST-MOMENTARY R128 CT14 74LVC14A SOIC14 FLAG2 SWT013 SPST-MOMENTARY CT17 EXIRQ1 R133 74LVC14A SOIC14
IRQ1
74LVC14A SOIC14
ANALOG DEVICES
Approvals
Drawn Checked Engineering
Cotton Road Nashua, 03063
Date
Title Size
21161N EZ-KIT LITE PUSHBUTTONS
Board
Date
11-12-2002_17:12
A0157-2000
Sheet
3.3V LED1 RED-SMT LED001 LED8 RED-SMT LED001
R143 DSP_RESET FLAG[4:9] FLAG4 FLAG5 FLAG6 FLAG7 FLAG8 FLAG9 74FCT244AT QSOP20 R137 LED2 AMBER-SMT LED001
R144
LED9 AMBER-SMT LED001
LED10 AMBER-SMT LED001
LED11 GREEN-SMT LED001
R145 74LVC00AD SOIC14 MONITOR 74LVC00AD SOIC14 LED3 AMBER-SMT LED001 LED4 AMBER-SMT LED001 LED5 AMBER-SMT LED001 LED6 AMBER-SMT LED001 LED7 AMBER-SMT LED001
R146
R147
VERF
3.3V
LED9 INDICATES AUDIO OUTPUT VALID LED10 INDICATES MONITOR FIRMWARE RUNNING
R138
R139
R140
R141
R142
R151 25MHZ OSC01 R152
3.3V
CLKIN XTAL XXMHZ 12.5MHZ OSC006 27PF 1206 3.3V R177 R149 74LVC14A SOIC14 DSP_RESET R150 AUDIO_OSC 27PF 1206
3.3V
SOFT_RESET R148 SWT013 SPST-MOMENTARY RESET RESET
74LVC00AD SOIC14
OSCILLATOR CRYSTAL USED 21161N
12.288MHZ OSC001
ANALOG DEVICES
Approvals
Drawn Checked Engineering
Cotton Road Nashua, 03063
ADM708SAR SOIC8
Date
Title Size
21161N EZ-KIT LITE LEDS, RESET,
Board
Date
2-19-2004_14:44
A0157-2000
Sheet
3.3V 3.3V
R158 R155 R156 R157 EBOOT JP19 IDC3X2 SJ24 SHORTING JUMPER DEFAULT=3 SJ25 SHORTING JUMPER DEFAULT=5 SJ23 SHORTING JUMPER DEFAULT=1 LBOOT R159 R160 SJ26 JP20 IDC3X2 SJ28 SHORTING JUMPER DEFAULT=NOT INSTALLED SJ27 SHORTING JUMPER DEFAULT=NOT INSTALLED SHORTING JUMPER DEFAULT=3
BOOT MODES
EBOOT LBOOT Booting Mode Output EPROM (Input) Host Processor (Input) Serial Boot (Input) Link Port (Input) Booting (Input) Reserved DENOTES FACTORY DEFAULT
REMOVE JP22 WHEN USING BOOT MODES (REFER SHEET
3.3V
R161
R162
R163 JP21 SJ29 IDC3X2 SJ30 SHORTING JUMPER DEFAULT=NOT INSTALLED SJ31 SHORTING JUMPER DEFAULT=5 SHORTING JUMPER DEFAULT=NOT INSTALLED
LOOP_ADC1_LEFT LOOP_ADC1_RIGHT
LOOP_DAC1_LEFT LOOP_DAC1_RIGHT LOOP_DAC2_LEFT LOOP_DAC2_RIGHT LOOP_DAC3_LEFT LOOP_DAC3_RIGHT LOOP_DAC4_LEFT LOOP_DAC4_RIGHT
CLKDBL CLK_CFG1 CLK_CFG0
LOOP_ADC2_LEFT LOOP_ADC2_RIGHT
CLOCK MODES
CLKDBL CLK_CFG1 CLK_CFG0 Core Clock Ratio DENOTES FACTORY DEFAULT Clock Ratio
SWT016 DIP8 TURNING SWITCHES PUTS BOARD LOOPBACK MODE
ANALOG DEVICES
Approvals
Drawn Checked Engineering
Cotton Road Nashua, 03063
Date
Title Size
21161N EZ-KIT LITE CONFIGURATION
Board
Date
11-12-2002_17:12
A0157-2000
Sheet
A[8:0] D[23:16] CON022 EBOOT LBOOT DMAG1 DMAR1 EXFLAG0 DMAG2 EXFLAG1 DMAR2 EXFLAG2 EXFLAG3 SBTS EXIRQ0 EXIRQ1 REDY BMSTR BRST CON023 TIMEXP EXIRQ2 DSP_RESET IDC5X1 IDC6X2 MISO MOSI SPIDS SPICLK 3.3V 1.8V
ANALOG DEVICES
Approvals
Drawn Checked Engineering
Cotton Road Nashua, 03063
Date
Title Size
21161N EZ-KIT LITE EXPANSION HEADERS
Board
Date
11-12-2002_17:12
A0157-2000
Sheet
LINK PORT CONNECTORS
CLKSH ACKSH D0SH D1SH D2SH D3SH D4SH D5SH D6SH D7SH L0D0 L0D1 L0D2 L0D3 L0D4 L0D5 L0D6 L0D7 SCLK3 SFS3 SD3A LINKPORT CON010 SD3B R218 0.00 1206 R217 0.00 1206 L0CLK L0ACK L0D[0:7] SCLK1 SFS1 SD1A SD1B CON014
SERIAL PORT CONENCTOR
SHGND SHGND
CLKSH ACKSH D0SH D1SH D2SH D3SH D4SH D5SH D6SH D7SH L1D0 L1D1 L1D2 L1D3 L1D4 L1D5 L1D6 L1D7 DBCLK L1CLK DLRCLK L1ACK DSDATA2 L1D[0:7] ASDATA2 IDC4X1
LINKPORT CON010
SHGND
SHGND
SHOULD INSTALLED WHEN USING LINK PORT
ANALOG DEVICES
Approvals
Drawn Checked Engineering
Cotton Road Nashua, 03063
Date
Title Size
21161N EZ-KIT LITE LINK PORTS SPORTS
Board
Date
11-13-2003_11:39
A0157-2000
Sheet
2.5A FUS001
FER13 CHOKE_COIL
DO-214AA 5V_REG_IN
INPUT OUTPUT ADP3339AKC-5 SOT-223 CT20 10UF 0.1UF
1000PF 1206 DO-214AA R167 100K 1206 CT19 10UF 0.1UF
7_5V_POWER CON005
FER9 1206
3.3V 1000PF 1206 3.3V DO-214AA SHGND INPUT OUTPUT INPUT OUTPUT ADP3338ARM-18 SOT-223 CT21 10UF 0.1UF CT22 10UF 0.1UF FER11 1206 SHGND AVCC AGND 1.8V FER10 1206
ADP3338ARM-33 SOT-223
1.8V 3.3V SJ34 SHORTING JUMPER DEFAULT=DNP R216 JP25 IDC2X1 C180 0.1UF INPUT OUTPUT R213 100K 1206 5V_REG_IN 3.3V INPUT OUTPUT ADP3339AKC-5 SOT-223 R211 500K RES002 R215 365K 1206 CT36 10UF C173 0.1UF R169 0.00 1206 AVCC 1.8V R168 0.00 1206
VDDINT
VDDEXT
ADP3331ART SOT23-6
R168 R169 USED MEASURE CURRENT DRAW
R212 1MEG RES002
R214 634K 1206
AGND
ANALOG DEVICES
Approvals
Drawn Checked Engineering
Cotton Road Nashua, 03063
Date
Title Size
21161N EZ-KIT LITE POWER
Board
Date
2-19-2004_14:44
A0157-2000
Sheet
3.3V VDDINT
0.01UF
0.01UF
0.01UF
0.01UF
0.01UF
0.01UF
0.01UF
0.01UF
0.01UF
C100 0.01UF
C118 0.01UF
C119 0.01UF
C120 0.01UF
C121 0.01UF
C122 0.01UF
C123 0.01UF
3.3V VDDINT VDDEXT
C101 0.01UF
C102 0.01UF
C103 0.01UF
C104 0.01UF
C105 0.01UF
C106 0.01UF
C107 0.01UF
C108 0.01UF
C124 0.01UF
C125 0.01UF
C126 0.01UF
C127 0.01UF
C128 0.01UF
C129 0.01UF
3.3V VDDEXT
C109 0.01UF
C110 0.01UF
C111 0.01UF
C112 0.01UF
C113 0.01UF
C114 0.01UF
C115 0.01UF
C116 0.01UF
C117 0.01UF
C130 0.01UF
C131 0.01UF
C132 0.01UF
C133 0.01UF
C134 0.01UF
C135 0.01UF
3.3V
(U1)
SDRAM (U2,
3.3V
C136 0.01UF
C137 0.01UF
C138 0.01UF
C139 0.01UF
C140 0.01UF
C141 0.01UF
C142 0.01UF
C143 0.01UF
C144 0.01UF
ANALOG DEVICES
FLASH (U5) INTERFACE (U6)
Cotton Road Nashua, 03063
Approvals
Drawn Checked Engineering
Date
Title Size
21161N EZ-KIT LITE BYPASS CAPS
Board
Date
11-12-2002_17:12
A0157-2000
Sheet
3.3V
AVCC
3.3V
3.3V
AVCC
AVCC
C145 0.01UF C146 0.01UF C147 0.01UF C148 0.01UF C149 0.01UF C150 0.1UF C151 0.1UF C152 0.1UF C153 0.1UF C154 0.01UF C155 0.01UF
AGND
SERIAL EEPROM (U7)
DIGITAL (U8)
NAND (U9)
AGND
AGND
CODEC (U10)
(U11)
AVCC 3.3V 3.3V 3.3V
C156 0.22UF
C157 0.22UF
C158 0.22UF
C159 0.22UF
C160 0.22UF
C161 0.22UF
C162 0.22UF
C163 0.22UF
C164 0.22UF
C172 0.22UF
C183 0.22UF
C165 0.01UF
C166 0.01UF
C167 0.01UF
C168 0.01UF
C169 0.01UF
C170 0.01UF
AGND
OPAMPS (U12-U20, U28, U29)
SCHMITT TRIGGERS (U21 U22)
OCTAL BUFFER (U23)
OSCILLATORS (U24 U25)
RESET (U26)
3.3V
3.3V
3.3V
3.3V
3.3V
3.3V
3.3V 3.3V 1.8V
C171 0.01UF
C186 0.01UF
C185 0.01UF
C184 0.01UF
C177 0.01UF
C176 0.01UF
C178 0.01UF
C179 0.01UF
C174 0.01UF
C175 0.01UF
CT23 4.7UF
CT24 4.7UF
CT25 4.7UF
NAND (U27)
SRAM (U30)
(U31)
FIFO (U32)
SHIFTER (U33)
(U34 U37)
QUICK SWITCH (U35 U36)
ANALOG DEVICES
Approvals
Drawn Checked Engineering
Cotton Road Nashua, 03063
Date
Title Size
21161N EZ-KIT LITE BYPASS CAPS
Board
Date
11-12-2002_17:12
A0157-2000
Sheet
INDEX
Symbols ~BMS, memory select pin, 2-2, ~MS0, memory select pin, 2-2, ~MS1, memory select pin, 2-2, abort, hang operations, 2-12 acknowledge, hang operation, 2-12 AD1836, xii, 2-6, 3-3, 3-4, control registers, 3-12 MIC1 input channel, port, select pin, AD1852, xii, 2-7, 3-4, sampling frequency, port, select pin, ADC1 input selector (JP11), ADC2 mode selection (JP7, JP8), Hardware Wizard, Windows ADSP-21161N processor boot modes, 3-10 clock jumper (JP21), 3-11 core speed, core voltage, external voltage,
jumper (JP19), 3-10 internal memory restrictions, interrupt pins, memory map, reset, port, analog audio input, interface, asynchronous FLAGs, audio connectors (P4-8, P17), 3-18 input, 2-6, interface, output, 2-8, stream, 3-14 bill materials, enabling (JP22), 3-12 ~BMS, select board measurements, 3-21 boot code, xiii load, memory select (~BMS), 3-3, 3-12
ADSP-21161N EZ-KIT Lite Evaluation System Manual
INDEX
memory space, mode select (JP20), 3-10 breadboard area, xiii breakpoints, 2-12 clear, hang operations, 2-12 CLK_CFG pins, 3-11 CLKDBL pins, 3-11 clock frequency, 3-11 mode jumper (JP21), 3-3, 3-11 modes, 3-11 common attributes, hardware breakpoints, 2-13 configuring SDRAM, connecting, EZ-KIT Lite board, connectors, -xii, 1-5, 3-16 JP11 (analog audio input), (digital audio input), (external port), 2-5, 2-6, 3-3, 3-19 (JTAG header), 3-19 (link port), 3-19 (link port), 3-19 (SPORT1, SPORT3), 3-20 (power), 1-5, 3-20 (USB), 1-6, 3-16 (optical input), 2-6, (mono jack), 2-6, (mono jack), 2-6, 3-4, (stereo jack), 2-6, 3-4, (external port), 3-3, 3-18 contents, EZ-KIT Lite package,
conventions, manual, -xxi converters, core clock ratio, 3-11 hang conditions, 2-11 voltage, 3-21 CS8414 digital receiver, 2-7, 3-5, 3-14 clock signals, synchronization signals, customer support, data hardware breakpoints, 2-15 Device Manager window, 1-15 digital audio playback, data, stereo channels, signals, DAI_P, 3-15 formats, EBOOT pins, 3-10 electrostatic discharge, emulator connector, xiii enable attribute, 2-14 address, attribute, 2-14 EPROM boot mode, 3-10, 3-12 example programs, exclusive, attribute, 2-14 expansion connector footprints, xiii external data bus, interrupts,
ADSP-21161N EZ-KIT Lite Evaluation System Manual
INDEX
memory, EZ-KIT Lite, port clock ratio, 3-11 port connectors, port interface, xiii, port signals, 3-18, 3-19 EZ-KIT Lite board architecture, features, specifications, 3-21 features, EZ-KIT Lite board, -xii FLAG directing, pins, 2-5, 3-15 registers, FLAG0, 2-5, 3-12, 3-15 enable jumper (JP4), FLAG1, 2-5, 3-12, 3-15 enable jumper (JP5), FLAG10, FLAG11, FLAG2, 2-5, 3-15 FLAG3, 2-5, 3-15 FLAG4, 3-14 FLAG4-9, 2-5, 3-14 FLAG5, 3-14 FLAG6, 3-14 FLAG7, 3-14 FLAG8, 3-14 FLAG9, 3-14 flash memory, xii, 2-2, 3-3, 3-12 programmer,
Found Hardware Wizard Windows 2000, 1-13 frequency jumper (JP6), general-purpose xiii global options, hardware breakpoints, 2-13 graphical user interface (GUI), hard reset, hardware breakpoints, 2-12, 2-17, 2-18 dialog box, 2-13 Help, online, xix, host processor booting, 3-10 processor interface, xiii, processor interface connector (P10), 3-19 hung conditions, 2-11 mode, ignore, hang operations, 2-12 input clock, installation, summary, installing EZ-KIT Lite driver, VisualDSP++ EZ-KIT Lite license, VisualDSP++ EZ-KIT Lite software, instruction hardware breakpoints, 2-16
ADSP-21161N EZ-KIT Lite Evaluation System Manual
INDEX
interface connectors, xiii interfaces graphical user interface (GUI) internal memory, EZ-KIT Lite, interrupt pins, push buttons, xiii also push buttons input push buttons (SW1-4), 3-15 pins FLAGs voltage, 3-21 IRQ0-2 pins, 2-6, 3-16 JTAG connector (P12), 3-19 emulation port, emulator, 3-19 jumper settings, jumpers, (SDRAM disable), JP10 (microphone), JP11 (audio in), 3-4, JP19 (processor ID), 3-10 (SPDIF), JP20 (boot mode), 3-10 JP21 (clock), 3-11 JP22 (~BMS), 3-12 JP26 (SW1 enable), 3-12 JP27 (SW2 enable), 3-12 (MCLK source), (frequency), (ADC2),
(ADC2), (microphone), latency, 2-18 LBOOT pins, 3-10 LEDs, xiii, 1-5, 2-5, 3-13, 3-14 LED1 (reset), 1-5, 3-14 LED10 (USB monitor), 1-15, 1-16, 3-15 LED11 (power), 1-5, 3-15 LED2 (FLAG9), 3-14 LED2-LED7 (FLAGs), 3-14 LED3 (FLAG8), 3-14 LED4 (FLAG7), 3-14 LED5 (FLAG6), 3-14 LED6 (FLAG5), 3-14 LED7 (FLAG4), 3-14 LED8 (DSP reset), 1-5, 1-14, 3-14 LED9 (VERF), 2-8, 3-14 line-in input channel, jacks, line-out jacks, link port, 3-5, 3-10 booting, 3-11 connectors, 3-19 MCLK, selecting (JP3), measurements, EZ-KIT Lite, 3-21 memory restrictions, select pins,
ADSP-21161N EZ-KIT Lite Evaluation System Manual
INDEX
microphone circuit, jacks, mode, attribute, 2-14 MODE2 register, no-boot mode, 3-11, 3-12 oscillator, 3-11 surface-mount, through-hole, through-hole crystal, package contents, configuration, power connector (P16), 3-20 (LED11), 3-15 specifications, 3-21 supply, 3-21 processor external memory, ADSP-21161N processor programmable FLAGs FLAGs push buttons, xiii, 2-6, 3-13, 3-15 (FLAG0), 3-15 (FLAG1), 3-15 (FLAG2), 3-15 (FLAG3), 3-15 (IRQ0), 3-15 (IRQ1), 3-15
(IRQ2), 3-15 (reset), 3-16 jacks, 2-7, registering, this product, 1-2, reset board, hang operation, 2-12 processor, 3-14 push button (SW8), 3-16 retry, hang operation, 2-12 sample frequencies, SDRAM configuration, control registers, disabling (JP1), memory, 2-2, 2-3, semiconductor receiver, serial booting, 3-10, 3-12 setting breakpoints, 2-18 EZ-KIT Lite hardware, target options, footprints, xiii SPDIF connectors, 3-14 modes, selecting (JP2), specifications, 3-21 audio interface,
ADSP-21161N EZ-KIT Lite Evaluation System Manual
INDEX
port, 3-4, 3-12 select pin, SPORT audio interface, connectors, SPORT0, xiii SPORT1, xiii, 3-12, 3-20 SPORT2, xiii SPORT3, xiii, 3-20 SRAM memory, start address, attribute, 2-14 starting VisualDSP++, 1-16 stereo jack (P7), 2-6, output channels, (FLAG0) push button, (JP26) enable push button, 3-12 (FLAG1) push button, (FLAG2) push button, (FLAG3) push button, (interrupt) push button, 2-6, 3-16 (interrupt) push button, 2-6, 3-16 (interrupt) push button, 2-6, 3-16 (reset) push button, 1-14 system architecture, EZ-KIT Lite board, requirements, target options dialog box, miscellaneous, 2-10
emulator exit, 2-10 while target halted, 2-10 UART, 3-11 cable, connector (P2), 3-16 debug interface, 3-19 driver installation, Windows 2000, 1-11 driver installation, Windows driver installation, Windows 1-12 interface, 3-14, 3-16 monitor (LED10), 3-15 user input, output, VERF flag (LED9), 2-8, 3-14 verifying driver installation, 1-14 VisualDSP++ documentation, installation, license, online Help, requirements, starting, 1-16 voltage regulators, xiii
ADSP-21161N EZ-KIT Lite Evaluation System Manual
INDEX
ADSP-21161N EZ-KIT Lite Evaluation System Manual
Other recent searches
SMPJ3T - SMPJ3T SMPJ3T Datasheet
SMPJ5T - SMPJ5T SMPJ5T Datasheet
SFF801 - SFF801 SFF801 Datasheet
SFF808 - SFF808 SFF808 Datasheet
PI6CV855-02 - PI6CV855-02 PI6CV855-02 Datasheet
KSC5802 - KSC5802 KSC5802 Datasheet
HD64F36037GFP - HD64F36037GFP HD64F36037GFP Datasheet
BCR191S - BCR191S BCR191S Datasheet
AKD4116-B - AKD4116-B AKD4116-B Datasheet
2SC2927 - 2SC2927 2SC2927 Datasheet
Privacy Policy | Disclaimer
© 2012 Datasheet Archive
