Hardware Software Installation Guide Edition: Revision December 2
|
|
|
Top Searches for this datasheet
Summit-ICE Emulator
Hardware Software Installation Guide
Edition: Revision December 2002
MANSUMICE
Analog Devices, Inc. Digital Signal Processing Division Technology Norwood, 02062-9106
Notice
Analog Devices, Inc. reserves right make changes discontinue product service identified this publication without notice. Analog Devices assumes liability Analog Devices applications assistance, customer product design, customer software performance, infringement patents services described herein. addition, Analog Devices shall held liable special, collateral, incidental consequential damages connection with arising furnishing, performance, this product. Analog Devices products intended life-support applications, devices, systems. Analog Devices product such applications without written consent appropriate Analog Devices officer prohibited. Users restricted from copying, modifying, distributing, reverse engineering reverse assembling reverse compiling Analog Devices Summit-ICE PCI-based emulator operational software (one copy made back-up purposes only). part this document reproduced form without permission.
Trademark Service Mark Notice
Analog Devices logo, SHARC, SHARC logo, TigerSHARC, TigerSHARC logo, EZ-ICE registered trademarks. VisualDSP++, VisualDSP++ logo, Blackfin, Blackfin logo, CROSSCORE, CROSSCORE logo, EZ-KIT Lite, ICEPAC, Collaborative trademarks Analog Devices, Inc. Microsoft Windows registered trademarks, Windows trademark Microsoft Corporation. other brand product names trademarks service marks their respective owners.
Limited Warranty
Summit-ICE hardware warranted against defects materials workmanship period year from date purchase from Analog Devices from authorized dealer.
Summit-ICE PCI-based emulator contains (electrostatic discharge) sensitive devices. Electrostatic charges readily accumulate human body equipment discharge without detection. Permanent damage occur devices subjected high-energy discharges. Proper precautions recommended avoid performance degradation loss functionality. Store used Summit-ICE PCI-based emulator protective-shipping package.
Summit-ICE PCI-based Emulator Manual
Table Contents
INTRODUCTION. MORE INFORMATION ABOUT ANALOG DEVICES PRODUCTS TECHNICAL CUSTOMER SUPPORT PURPOSE THIS MANUAL INTENDED AUDIENCE MANUAL CONTENTS ON-LINE HELP
GETTING STARTED OVERVIEW CONTENTS YOUR SUMMIT-ICE PACKAGE CONFIGURATION INSTALLATION TASKS 2.4.1 Install Summit-ICE Hardware
2.4.1.1 Unpacking Emulator .2-2 2.4.1.2 Installing Summit-ICE Board your Computer.2-2 2.4.1.3 Configuring Summit-ICE Pod.2-3 2.4.1.3.1 Connecting Target.2-3 2.4.1.3.2 Connecting Target.2-4 2.4.1.3.3 Reducing Noise Issues JTAG Signals.2-4
CONNECTING SUMMIT-ICE BOARD CONNECTING YOUR TARGET SYSTEM INSTALLING SUMMIT-ICE DRIVER 2.7.1 Windows Driver Installation 2.7.2 Windows Driver Installation 2-10 2.7.3 Windows 2000 Driver Installation 2-10 2.7.4 Windows Driver Installation 2-13 2.7.5 Verifying Driver Installation 2-16 2.7.6 Creating Platform. 2-20
2.7.6.1 2.7.6.2 Creating platform based Analog Devices Evaluation Kit. 2-20 Creating Platform from Scratch 2-23
SUPPORT. TECHNICAL SUPPORT QUALITY ASSURANCE
REFERENCES.
INDEX
Summit-ICE PCI-based Emulator Manual
List Tables
TABLE 2-1: MINIMUM CONFIGURATION
List Figures
FIGURE JUMPERS FIGURE LEDS FIGURE TERMINATORS CONNECTED JTAG SIGNALS FIGURE 2-4: HARDWARE WIZARD DIALOG FIGURE 2-5: SEARCH DRIVER FIGURE 2-6: SEARCH CD-ROM FIGURE 2-7: DRIVER LOCATED FIGURE 2-8: SEARCH .SYS FILE DIALOG FIGURE 2-9: OPEN .SYS FILE. FIGURE 2-10: COPYING FILES. FIGURE 2-11: FINISH SOFTWARE INSTALLATION FIGURE 2-12: FOUND HARDWARE WIZARD 2-10 FIGURE 2-13: SEARCH SUITABLE DRIVER 2-11 FIGURE 2-14: LOCATE DRIVER FILES 2-11 FIGURE 2-15: DRIVER FILE SEARCH RESULTS 2-12 FIGURE 2-16: COMPLETING DRIVER INSTALLATION DIALOG 2-13 FIGURE 2-17: FOUND HARDWARE WIZARD 2-14 FIGURE 2-18: SEARCH SUITABLE DRIVER 2-15 FIGURE 2-19: COMPLETING DRIVER INSTALLATION DIALOG 2-16 FIGURE 2-20: VERIFIYING DRIVER INSTALLATION 2-17 FIGURE 2-21: ICETEST UTILITY. 2-17 FIGURE 2-22: DETECTED EMULATORS 2-18 FIGURE 2-23: ICETEST PASS. 2-19 FIGURE 2-24 ICETEST FAILURE 2-20 FIGURE 2-25: VISUALDSP++ CONFIGURATOR (FROM TEMPLATE). 2-21 FIGURE 2-26: PLATFORM PROPERTIES (FROM TEMPLATE) 2-21 FIGURE 2-27: VISUALDSP++ CONFIGURATOR (FROM TEMPLATE) PLATFORM ADDED 2-22 FIGURE 2-28: PLATFORM PROPERTIES (FROM SCRATCH). 2-23 FIGURE 2-29: DETECTED EMULATORS 2-24 FIGURE 2-30: DEVICE PROPERTIES 2-24 FIGURE 2-31: PLATFORM PROPERTIES (FROM SCRATCH) DEVICE ADDED 2-25 FIGURE 2-32: VISUALDSP++ CONFIGURATOR (FROM SCRATCH) PLATFORM ADDED 2-25
Summit-ICE PCI-based Emulator Manual
Introduction
Thank purchasing Analog Devices Summit-ICE PCI-based JTAG emulator. SummitICE used conjunction with VisualDSP++ development environment create, test debug advanced application software Analog devices fixed floating-point JTAG based DSPs. Summit-ICE system provides state-of-the-art support JTAG-compliant Analog Devices DSPs. features Summit-ICE include: Plug-n-Play card Windows Windows Windows 2000, Windows operation Emulation industry standard Analog Devices JTAG families DSPs Rugged high-speed JTAG emulation
More Information About Analog Devices Products
Analog Devices accessed Internet http://www.analog.com. directly access pages http://www.analog.com/dsp. This page provides access specific technical information documentation, product overviews, product announcements. specific information about tools, also obtain additional information about Analog Devices products following ways: questions requests information (781) 461-3010. Access Computer Products Division File Transfer Protocol (FTP) site ftp://ftp.analogdevices.com/ ftp://137.71.25.69 ftp://ftp.analog.com.
Technical Customer Support
reach Customer Support group following ways: E-mail Tools questions dsptools.support@analog.com Tools Tech Support Form: E-mail general questions dsp.support@analog.com
Summit-ICE PCI-based Emulator Manual
dsp.europe@analog.com (European customer support) Call: (800) ANALOGD Contact your local Analog Devices sales office authorized Analog Devices distributor.
Purpose This Manual
Summit-ICE Hardware Software Installation Guide provides directions installing hardware software Summit-ICE your This manual also provides description configuration components Summit-ICE PCI-based emulator.
Intended Audience
This manual installation guide Summit-ICE PCI-based emulator. This manual intended help customer quickly install Summit-ICE that they begin using VisualDSP++.
Manual Contents
This manual contains following information: Chapter Introduction Provides manual information Analog Devices contact information. Chapter Getting Started Provides software hardware installation procedures, system requirements, basic board information. Chapter Support Provides Technical Support Contact information. Chapter References Provides information different resources available developing application.
Summit-ICE PCI-based Emulator Manual
On-line Help
Your software installation includes online Help part Windows interface. These Help files provide information about VisualDSP++ Summit-ICE. view VisualDSP++'s Help, click Help menu item Windows task select Help. documents following tables found through online help Docs folder your VisualDSP++ installation. more documentation, please
Summit-ICE PCI-based Emulator Manual
Getting Started
Overview
This chapter provides information need begin using Summit-ICE system. Install your software hardware order presented section correct operation. This chapter following sections: Contents your Summit-ICE Package (Section 2.2) Provides list components that shipped with this Summit-ICE PCIbased Emulator. Configuration (Section 2.3) Describes minimal requirement work with Summit-ICE PCI-based Emulator. Installation Tasks (Section 2.4) Describes step-by-step procedure setting hardware software.
Contents your Summit-ICE Package
Your Summit-ICE PCI-based emulator package contains following items: Summit-ICE JTAG daughter card Summit-ICE assembly containing emulation driver software Registration card please fill return
Summit-ICE PCI-based emulator contains (electrostatic discharge) sensitive devices. Electrostatic charges readily accumulate human body equipment discharge without detection. Permanent damage occur devices subjected high-energy discharges. Proper precautions recommended avoid performance degradation loss functionality. Store used Summit-ICE protective-shipping package.
Configuration
correct operation Summit-ICE PCI-based emulator, your computer must have minimal configuration shown Table 2-1.
Summit-ICE PCI-based Emulator Manual
Table 2-1: Minimum Configuration
Windows Windows Windows 2000, Windows Intel compatible) processor monitor color video card 2-button mouse free hard drive available slot CD-ROM drive
Installation Tasks
following tasks provided safe effective Summit-ICE PCI-based emulator. Follow these instructions order presented ensure correct operation your software hardware. Install Summit-ICE hardware Install Summit-ICE driver Verify driver installation.
2.4.1 Install Summit-ICE Hardware
This section provides information required install Summit-ICE card into your
Summit-ICE PCI-based emulator contains (electrostatic discharge) sensitive devices. Electrostatic charges readily accumulate human body equipment discharge without detection. Permanent damage occur devices subjected high-energy discharges. Proper precautions recommended avoid performance degradation loss functionality. Store used Summit-ICE protective-shipping package.
2.4.1.1 Unpacking Emulator
Remove Summit-ICE board from package. Care should taken when handling these boards avoid discharge static electricity, which damage some components. aside. Summit-ICE board must first installed your computer.
2.4.1.2 Installing Summit-ICE Board your Computer
specific instructions installing card into your computer consult documentation that provided manufacturer your computer.
Summit-ICE PCI-based Emulator Manual
Upon installing your Summit-ICE will need install driver before first time. Refer section instructions install appropriate driver.
2.4.1.3 Configuring Summit-ICE
Summit-ICE contains four internal jumpers. These jumpers accessed removing four screws bottom plastic enclosure removing enclosure. jumpers shown Figure 2-1. Summit-ICE also contains status LEDs. left voltage status (3V/5V) right emulator status. LEDs shown Figure 2-2. Periodic activity emulator status indicates communication between target DSPs emulator.
Figure Jumpers
Figure LEDs 2.4.1.3.1 Connecting Target
Jumper used differentiate between target. This only jumper that most users will need change. When jumper installed JTAG signals configured connect target. When jumper installed left side illuminated.
Summit-ICE PCI-based Emulator Manual
2.4.1.3.2 Connecting Target
When jumper installed JTAG signals configured connect target. When jumper installed left illuminated indicating target. This default setting.
2.4.1.3.3 Reducing Noise Issues JTAG Signals
There three jumpers provided help reduce problems that arise because ringing reflections JTAG signals target board. default that these jumpers installed. three jumpers Jumpers used adding parallel terminator CLKIN signals. When jumper installed parallel terminator connected CLKIN signals. Figure shows terminator connected JTAG signals. important note that target MUST able drive load before these jumpers installed. cannot drive this load directly; driver should inserted between JTAG signals JTAG signals header.
Figure Terminators connected JTAG Signals
Jumper provided allow board level test pins JTAG connector (BTMS, BTCK, BTRST, BTDI) used ground pins allow greater shielding JTAG cable connecting target. These pins should only used ground pins they used your target.
Summit-ICE PCI-based Emulator Manual
Connecting Summit-ICE Board
connects Summit-ICE board through shielded flat ribbon cable 25-pin connector. Connect Summit-ICE before applying power JTAG header attached connected/disconnected without damaging system long target system powered down. Important! Connect/disconnect remote to/from emulator card only with power turned off. Failure follow this precaution result damage board.
Connecting your Target System
connects target processor through JTAG interface. target board must built with appropriate JTAG connector. Please note position pin. should used guide connect target. Included with Summit- system extender connectors. These extenders used connect Summit-ICE system target, which designed with ICEPACTM. These extenders allow connection JTAG pins ICEPAC header.
Installing Summit-ICE Driver
Summit-ICE installed Windows Windows Windows 2000, Windows requires available slot. Section 2.7.1 describes installation Windows Section 2.7.2 describes installation Windows Section 2.7.3 describes installation Windows 2000. Section 2.7.4 describes installation Windows
2.7.1 Windows Driver Installation
Before using Summit-ICE first time, Windows driver must installed. This accomplished follows:
Summit-ICE PCI-based Emulator Manual
Insert VisualDSP++ Emulator Tools CD-ROM into CD-ROM drive. Power start Windows This will activate Windows Hardware Wizard shown Figure 2-4.
Figure 2-4: Hardware Wizard Dialog
Click Next. Select Search best driver your device shown Figure 2-5.
Figure 2-5: Search Driver
Summit-ICE PCI-based Emulator Manual
Click Next. Select CD-ROM drive shown Figure 2-6.
Figure 2-6: Search CD-ROM
Click Next. Windows will locate PCIEmul.inf file that CD-ROM shown Figure 2-7.
Figure 2-7: Driver Located
Summit-ICE PCI-based Emulator Manual
Click Next. Figure will appear.
Figure 2-8: Search .sys File Dialog
Click Browse button. Figure will appear.
Figure 2-9: Open .sys File
Drives select your CD-ROM drive. Click Figure 2-10 will appear.
Summit-ICE PCI-based Emulator Manual
Figure 2-10: Copying Files
Click driver installation complete shown Figure 2-11.
Figure 2-11: Finish Software Installation
Click Finish exit wizard. Verify driver installation following instructions Section 2.7.5.
Summit-ICE PCI-based Emulator Manual
2.7.2 Windows Driver Installation
Before using Summit-ICE first time, Emulator Tools installation sure select Summit/Mountain Emulator install. install will place driver appropriate folder that driver installed properly.
2.7.3 Windows 2000 Driver Installation
Before using Summit-ICE first time, Windows 2000 driver must installed. This accomplished follows: Insert VisualDSP++ Emulator Tools CD-ROM into CD-ROM drive. Power start Windows 2000. This will activate Windows 2000 Found Hardware Wizard shown Figure 2-12.
Figure 2-12: Found Hardware Wizard
2-10
Summit-ICE PCI-based Emulator Manual
Click Next. Select Search suitable driver device shown Figure 2-13.
Figure 2-13: Search Suitable Driver
Click Next. Ensure that CD-ROM drive selected shown Figure 2-14.
Figure 2-14: Locate Driver Files 2-11
Summit-ICE PCI-based Emulator Manual
Click Next. Figure 2-15 appears.
Figure 2-15: Driver File Search Results
2-12
Summit-ICE PCI-based Emulator Manual
Click Next. Windows 2000 will automatically install Summit-ICE JTAG Emulator driver. driver installation complete shown Figure 2-16.
Figure 2-16: Completing Driver Installation Dialog
Click Finish exit wizard. Verify driver installation following instructions section 2.7.5.
2.7.4 Windows Driver Installation
Before using Summit-ICE first time, Windows driver must installed. This accomplished follows:
2-13
Summit-ICE PCI-based Emulator Manual
Insert VisualDSP++ Emulator Tools CD-ROM into CD-ROM drive. Power start Windows This will activate Windows Found Hardware Wizard shown Figure 2-17.
Figure 2-17: Found Hardware Wizard
Select Install from list specific location. Click Next.
2-14
Summit-ICE PCI-based Emulator Manual
Select Search best driver these locations select Include this location search shown Figure 2-18. Enter path drive that contains VisualDSP++ Emulator Tools CD-ROM.
Figure 2-18: Search Suitable Driver
Click Next.
2-15
Summit-ICE PCI-based Emulator Manual
Windows will automatically install Summit-ICE JTAG Emulator driver. driver installation complete shown Figure 2-19.
Figure 2-19: Completing Driver Installation Dialog
Click Finish exit wizard. Verify driver installation following instructions Section 2.7.5.
2.7.5 Verifying Driver Installation
Before using your Summit-ICE PCI-based emulator, verify that driver software installed properly.
2-16
Summit-ICE PCI-based Emulator Manual
Open Device Manager verify that Summit-ICE JTAG Emulator shows under Emulators with exclamation point shown Figure 2-20.
Figure 2-20: Verifiying Driver Installation
From Start\Program Files\VisualDSP\ICE Test Utility open IceTest shown Figure 2-21 verify that driver installed correctly that there connectivity with target board.
Figure 2-21: IceTest Utility
2-17
Summit-ICE PCI-based Emulator Manual
there more than emulator installed click browse button (".") right Type shown Figure 2-21 bring list Emulators installed shown Figure 2-22. there only emulator installed then address information will filled automatically when launching IceTest skip step
Figure 2-22: Detected Emulators
2-18
Summit-ICE PCI-based Emulator Manual
Choose Summit-ICE shown Figure 2-22 click This will fill Base Address with appropriate address shown Figure 2-21. Ensure that JTAG header connected target board click Start. tests pass, green check marks appear next entries Status group shown Figure 2-23.
Figure 2-23: IceTest Pass
driver installed correctly communication with target board been established. they pass will note bottom dialog explaining failure more detail show Figure 2-24.
2-19
Summit-ICE PCI-based Emulator Manual
Figure 2-24 IceTest Failure 2.7.6 Creating Platform
When creating platform, existing template create template from scratch. Base your platform existing platforms (Analog Devices evaluation kits) listed VisualDSP++ Configurator window's Platform Templates box. launch VisualDSP++ Configurator Start\Program Files\VisualDSP\VisualDSP++ Configurator.
2.7.6.1 Creating platform based Analog Devices Evaluation
create platform that based Analog Devices, Inc. evaluation follow theses instructions: NOTE: Addresses shown example purposes only. Actual addresses will depend operating system.
2-20
Summit-ICE PCI-based Emulator Manual
Bring VisualDSP++ Configurator from Windows Start menu. Platform Templates box, highlight template which base your platform shown Figure 2-25.
Figure 2-25: VisualDSP++ Configurator (from template)
Click Copy Figure 2-26 will appear.
Figure 2-26: Platform Properties (from template)
2-21
Summit-ICE PCI-based Emulator Manual
required, device following steps section 2.7.6.2 click your platform shown Figure 2-27.
Figure 2-27: VisualDSP++ Configurator (from template) Platform Added
2-22
Summit-ICE PCI-based Emulator Manual
Click finish VisualDSP++ Configurator
2.7.6.2 Creating Platform from Scratch
Follow instructions below create platform that based Analog Devices evaluation kit. Bring VisualDSP++ Configurator from Windows Start menu. Click VisualDSP++ Configurator open Platform Properties dialog shown Figure 2-28 create platform.
Figure 2-28: Platform Properties (from scratch)
2-23
Summit-ICE PCI-based Emulator Manual
name field, type appropriate name platform that being created. Type field indicates type emulator that would like use. there more than emulator installed click browse button (".") right Type shown Figure 2-28 bring list Emulators installed shown Figure 2-29. there only emulator installed then address information will filled automatically when launching IceTest skip step
Figure 2-29: Detected Emulators
Highlight emulator used your platform click Notice that Emulator Settings group shown Figure 2-28 gets filled with correct information based emulator chose. Highlight Device Devices list click Modify display Device Properties dialog shown Figure 2-30.
Figure 2-30: Device Properties
2-24
Summit-ICE PCI-based Emulator Manual
Select appropriate name your device then select type device which will connecting. Click will that your device shows under Devices list with appropriate type shown Figure 2-31.
Figure 2-31: Platform Properties (from scratch) Device Added
Click your platform shown Figure 2-32.
Figure 2-32: VisualDSP++ Configurator (from scratch) Platform Added
Click finish VisualDSP++ Configurator.
2-25
Summit-ICE PCI-based Emulator Manual
Support
Technical Support
technical support, contact Analog Devices Tools Technical Support group following ways: Fill Tools Technical Support site form Send description problem e-mail dsptools.support@analog.com Call customer support hotline 1-800-ANALOG-D (1-800-262-5643 U.S.A. only)
direct support Analog Devices' DSPs, call Analog Devices' Applications Engineering group 1-800-ANALOG-D email dsp.support@analog.com.
Quality Assurance
Analog Devices committed providing quality products services. continually provide this quality, please contact Quality Assurance Department directly have concerns (603) 883-2430, Monday through Friday during normal business hours e-mail dsptools@analog.com. Quality Assurance Manager will listen your concerns provide timely effective solution.
Summit-ICE PCI-based Emulator Manual
References
This section describes other documentation resources find helpful developing your application. information designing interface between Analog Devices JTAG emulation header your custom target board, refer latest version Analog Devices EE-68. information architecture system interface ADSP processor, refer appropriate Analog Devices Hardware Reference. ADSP timing specification other hardware design information, refer appropriate Data Sheet. complete information software development tools (assembler, compiler, linker, on), refer documentation included with VisualDSP++. This information available printed manuals, online help, online format. information about your development platform, refer your operating system manuals hardware system manuals. information about digital signal processing theory applications, wish consult: Higgins. Digital Signal Processing VLSI. Prentice-Hall, 1990. Oppenheim Schafer. Digital Signal Processing. Prentice-Hall, 1975.
Summit-ICE PCI-based Emulator Manual
Index
.iii, 2-3, iii, Configurator .2-17, 2-20, 2-21, 2-22, 2-23, 2-25 Customer Support. Daughter Card Documents. Driver.2-1, 2-2, 2-3, 2-5, 2-6, 2-7, 2-9, 2-10, 2-11, 2-13, 2-15, 2-16, 2-17, 2-19 Electrostatic .ii, 2-1, Hardware 1-2, 2-2, 2-6, 2-10, 2-14, Help, On-line IceTest Utility. 2-17 Installation.i, 1-2, 2-1, 2-2, 2-5, 2-10, 2-13, 2-16, 2-17 JTAG .1-1, 2-1, 2-13, 2-16, 2-17, 2-19 Jumpers. 2-3, 2-3, platform. 2-20, 2-21, 2-22, 2-23, 2-25 Configuration. PCI. 1-1, 1-2, 2-1, 2-2, 2-3, 2-5, 2-10, 2-13, 2-16 Pod. 2-1, Properties. 2-21, 2-23, 2-24, 2-25 Quality Assurance Questions References Registration Card. Software. 1-2, 2-1, 2-2, 2-16, Status 2-19 Technical Support. 1-2, Test 2-17 VisualDSP++.ii, 1-1, 1-2, 1-3, 2-6, 2-10, 2-14, 215, 2-20, 2-21, 2-22, 2-23, 2-25, Help
Summit-ICE PCI-based Emulator Manual
Other recent searches
uPG2214TB - uPG2214TB uPG2214TB Datasheet
SB20150CT - SB20150CT SB20150CT Datasheet
SB20200CT - SB20200CT SB20200CT Datasheet
S-90N0133SUA - S-90N0133SUA S-90N0133SUA Datasheet
PS2861-1 - PS2861-1 PS2861-1 Datasheet
PA025XSC - PA025XSC PA025XSC Datasheet
OSC1603A - OSC1603A OSC1603A Datasheet
NDR3003 - NDR3003 NDR3003 Datasheet
ND39G1 - ND39G1 ND39G1 Datasheet
2SK3271-01 - 2SK3271-01 2SK3271-01 Datasheet
Privacy Policy | Disclaimer
© 2012 Datasheet Archive
