Emulation M16C/6V Group M306V0 User's Manual Rev.1.00 Octobe
|
|
|
Top Searches for this datasheet
M306V0T-RPD-E
Emulation M16C/6V Group M306V0
User's Manual
Rev.1.00 October 2003 REJ10J0380-0100Z
PC/AT registered trademarks International Business Machines Corporation.
Keep safety first your circuit designs! Renesas Technology Corporation Renesas Solutions Corporation maximum effort into making semiconductor products better more reliable, there always possibility that trouble occur with them. Trouble with semiconductors lead personal injury, fire property damage. Remember give consideration safety when making your circuit designs, with appropriate measures such placement substitutive, auxiliary circuits, (ii) nonflammable material (iii) prevention against malfunction mishap.
Notes regarding these materials These materials intended reference assist customers selection Renesas Technology product best suited customer's application; they convey license under intellectual property rights, other rights, belonging Renesas Technology Corporation, Renesas Solutions Corporation third party. Renesas Technology Corporation Renesas Solutions Corporation assume responsibility damage, infringement third-party's rights, originating product data, diagrams, charts, programs, algorithms, circuit application examples contained these materials. information contained these materials, including product data, diagrams, charts, programs algorithms represents information products time publication these materials, subject change Renesas Technology Corporation Renesas Solutions Corporation without notice product improvements other reasons. therefore recommended that customers contact Renesas Technology Corporation, Renesas Solutions Corporation authorized Renesas Technology product distributor latest product information before purchasing product listed herein. information described here contain technical inaccuracies typographical errors. Renesas Technology Corporation Renesas Solutions Corporation assume responsibility damage, liability, other loss rising from these inaccuracies errors. Please also attention information published Renesas Technology Corporation Renesas Solutions Corporation various means, including Renesas home page (http://www.renesas.com). When using information contained these materials, including product data, diagrams, charts, programs, algorithms, please sure evaluate information total system before making final decision applicability information products. Renesas Technology Corporation Renesas Solutions Corporation assume responsibility damage, liability other loss resulting from information contained herein. Renesas Technology semiconductors designed manufactured device system that used under circumstances which human life potentially stake. Please contact Renesas Technology Corporation, Renesas Solutions Corporation authorized Renesas Technology product distributor when considering product contained herein specific purposes, such apparatus systems transportation, vehicular, medical, aerospace, nuclear, undersea repeater use. prior written approval Renesas Technology Corporation Renesas Solutions Corporation necessary reprint reproduce whole part these materials. these products technologies subject Japanese export control restrictions, they must exported under license from Japanese government cannot imported into country other than approved destination. diversion reexport contrary export control laws regulations Japan and/or country destination prohibited. Please contact Renesas Technology Corporation Renesas Solutions Corporation further details these materials products contained therein.
Precautions taken when using this product This product development supporting unit your program development evaluation stages. mass-producing your program have finished developing, sure make judgment your risk that practical performing integration test, evaluation, some experiment else. event shall Renesas Solutions Corporation liable consequence arising from this product. Renesas Solutions Corporation strives renovate provide workaround product malfunction some charge without charge. However, this does necessarily mean that Renesas Solutions Corporation guarantees renovation provision under circumstances. This product been developed assuming program development evaluation laboratories. Therefore, does fall under application Electrical Appliance Material Safety protection against electromagnetic interference when used Japan. attempt modify this equipment. modified, your authority operate this equipment might voided FCC. Note: This equipment been tested found comply with limits Class digital device, pursuant part Rules. These limits designed provide reasonable protection against harmful interference when equipment operated commercial environment. This equipment generates, uses, radiate radio frequency energy and, installed used accordance with user's manual, cause harmful interference radio communications. Operation this equipment residential area likely cause harmful interference which case user will required correct interference expense. Warning: This Class product. domestic environment this product cause radio interference which case user required take adequate measures. inquiries about contents this document product, fill text file installer emulator debugger generates following directory email your local distributor. Renesas Tools Homepage http://www.renesas.com/en/tools
Preface
M306V0T-RPD-E emulation M16C/6V group Renesas 16-bit MCUs. M306V0T-RPD-E used being connected PC4701 emulator (PC4701HS, PC4701L, PC4700H PC4700L) controlled emulator debugger. This manual mainly explains specifications setting M306V0T-RPD-E. detail information about PC4701 emulator emulator debugger, refer each user's manual. check components this product, refer "Things Check When Unpacking" this manual. there question doubt about this product, contact your local distributor.
product properly
Precautions Safety
both this user's manual product itself, several icons used insure proper handling this product also prevent injuries other persons, damage your properties. icons' graphic images meanings given "Chapter Precautions Safety". sure read this chapter before using product.
When using outside Japan
When using Europe, United States, Canada, sure both emulator emulation which meet local standards. standards when this product used with PC4700H PC4700L emulator.
Contents
Terminology Things Check When Unpacking Chapter Precautions Safety Safety Symbols Meanings Precautions Safety
Warning
Warning Installation Warning Environment
Caution
Cautions Taken This Product Caution Installation
Important
Notes PC4701 Emulators Notes Abnormal Operation Notes Target System Notes Connecting Target System Note Reset Input from Target System Note HOLD Input from Target System Note Address Access Notes Differences between Actual Emulator Notes Settings References Note Changing Data Area When Program Executed Note Reading Internal Sources Note Stack
Chapter Introduction Chapter Specifications Chapter Settings Target Systems Positions Switches Settings Procedure Setting Oscillation Frequency Data Slicer Signals Clock Signal Circuits Procedure Setting Switches Procedure Writing File
Chapter Method Connection Connecting Emulator Main Unit Connecting Target System Chapter Constraints Chapter Operation Timing (Memory Expansion Microprocessor Modes) Separate wait) Separate (with wait), When Accessing External Memory Area Multiplex (with wait), When Accessing External Memory Area Timing Requirements Chapter Electrical Characteristics Chapter Maintenance Guarantee Maintenance Guarantee Repair Provisions Request Repair Chapter Troubleshooting 10.1 When M306V0T-RPD-E Does Work Properly Appendix External Dimensions External Dimensions M306V0T-RPD-E External Dimensions FLX-100LCC Appendix Connection Diagrams
Terminology
Some specific words used this User's Manual defined follows:
PC4701
This means generic name PC4701HS, PC4701L, PC4700H, PC4700L emulators.
PC4701 system
This means emulator system built around PC4701 emulator. PC4701 emulator system configured with emulator main unit, emulation pod, emulator debugger, host machine.
Emulator debugger
This means software tool control emulator from host machine through interface. Emulator debugger: M3T-PD30 (V.3.00 Release later) Host machine: PC/AT compatible Windows Windows CPU: 486DX4-100 Pentium faster recommended) Memory: more
Target
This means microcomputer going debug.
Target system
This means user's application system using microcomputer debugged.
Things Check When Unpacking
M306V0T-RPD-E consists following parts manuals. When unpacking, check your M306V0T-RPD-E package contains these items.
M306V0T-RPD-E (Emulation pod) FLX120-RPD (Flexible cable connecting PC4701 emulator) Screws connecting PC4701 emulator FLX100 (Flexible cable connecting target system, already connected) FLX-100LCC (Converter board 100LCC package) OSC-2 (Oscillator board) M306V0T-RPD-E English user's manual (this manual) M306V0T-RPD-E Japanese user's manual
these items missing found faulty, please contact your local distributor. Also, there question doubt about packaged products, contact your local distributor.
CAUTION
Please keep M306V0T-RPD-E's packing cushion material your place reuse later time when sending your product repair other purposes. Always these packing cushion material when transporting M306V0T-RPD-E.
Chapter Precautions Safety
both user's manual product itself, several icons used insure proper handling this product also prevent injuries other persons, damage your properties. This chapter describes precautions which should taken order this product safely properly. sure read this chapter before using this product.
Safety Symbols Meanings
requirements shown "WARNING" sentences ignored, equipment cause serious personal injury death. requirements shown "CAUTION" sentences ignored, equipment malfunction. means important information using this product.
WARNING CAUTION IMPORTANT
Example:
addition three above, following also used appropriate. means WARNING CAUTION. CAUTION AGAINST ELECTRIC SHOCK means PROHIBITION. Example: DISASSEMBLY PROHIBITED
means FORCIBLE ACTION. Example: UNPLUG POWER CABLE FROM RECEPTACLE.
following pages describe symbols "WARNING", "CAUTION", "IMPORTANT".
Precautions Safety
WARNING
Warning Installation:
this product water areas high humidity. Spilling water some other liquid into main unit cause unrepairable damage.
Warning Environment:
This equipment used environment with maximum ambient temperature 35°C. Care should taken that this temperature exceeded.
CAUTION
Cautions Taken This Product:
disassemble modify this product personal. Disassembling modifying this product cause damage. caution when handling main unit. careful apply mechanical shock. touch directly connector pins emulator main unit target connector pins with your hand. pull emulation main unit FLX120-RPD flexible cable FLX100 flexible cable connecting target system. flexible cables FLX120-RPD FLX100 different from earlier models. slits make them more flexible. However, excessive flexing force break conductors. inch-size screws this equipment. screws used this equipment (meter-size) type screws. When replacing screws, same type screws used equipment.
Cautions Installation:
place main unit side when use.
IMPORTANT
Notes PC4701 Emulators:
PC4700H emulators whose serial number ends with number cannot used with M306V0TRPD-E. only products whose serial number ends with letter alphabet. serial number bottom PC4700H. Example: 5KE100 used with M306V0T-RPD-E. Requires upgrade. Example: 5LE123B used with M306V0T-RPD-E. turn power when downloading firmware. emulator powered middle process, will become unable start normally. cases when power inadvertently shut off, re-execute downloading.
Notes Abnormal Operation:
PC4701 system does pass self-checks (excluding when target system error occurs), there possibility trouble system. such case, contact place purchase. Please take note that self-check should executed under following conditions. target system connected. Switch position, '16' (see Chapter emulator malfunctions external interference some other causes, follow steps given below. Press system reset switch located front panel emulator. emulator does return normal operation despite step above, turn power source emulator, turn again.
Notes Target System:
Because emulation does have capacity supply power other devices, design your system that emulator powered target system. Make sure that target's supply voltage within specification range +4.5 change power supply voltage target system after activating power. Before turning power anything, check host machine, emulator main unit, emulation pod, conversion board user's target system properly connected. Activate power units explained here following. Turn power target system, then PC4701 continuously. After turning power PC4701, check Target Status LEDs emulator' front panel M306V0T-RPD-E ready operate. power supplied? Check that Target Status (POWER) reset released? Check that Target Status (RESET) off.
IMPORTANT
Notes Connecting Target System:
When connecting FLX100 flexible cable converter board, careful forcibly press connector converter board. (The flexible cable converter board guaranteed only insertion/removal iterations.) Especially careful insert converter board wrong direction.
Note Reset Input from Target System:
reset input from target system accepted only during program execution (while signal lamp PC4701 lit).
Note HOLD Input from Target System:
Input level signal into HOLD only during program execution. Doing while program stopped during time debugging cause emulator malfunction.
Note Address Access:
With M16C/6V group MCUs, when maskable interrupt generated, interrupt data (interrupt number interrupt request level) stored address read out. Also, interrupt request cleared when address read out. Consequently, when address readout instruction executed when address read cause program runaway, malfunction occurs that interrupt executed despite interrupt request, because request highest priority interrupt factor enabled cleared. Therefore, with M306V0T-RPD-E, address read anything other than interrupt processing, yellow lights warning. When this lights there possibility illegal access address therefore check program. This extinguished from emulator reset switch.
IMPORTANT
Notes Differences between Actual Emulator:
Emulator operation differs from mask operation, listed below: Reset condition Initial values internal resource data power-on Internal capacities, etc. Ports M306V0T-RPD-E's ports, ports connected user's target system through port emulation circuit inside M306V0T-RPD-E. Table gives device which uses these ports. Table device used each ports
Port P00-P57 device M60074-0111FP
Writing into pullup control registers (addresses 03FC16 03FD16 respectively) write into pullup control registers (addresses 03FC16 03FD16 respectively), necessary write word data from address 03FC16. This M306V0T-RPD-E restriction. Ports enable pullup when setting (PUR12) pullup register single chip mode, sure (PM02) (PM07) processor mode register '0'. This M306V0T-RPD-E restriction. BCLK output disable disable BCLK output, necessary BCLK output disable (PM07) processor mode register (address 000416) port direction register (address 03EB16) '0'. This M306V0T-RPD-E restriction. Hold control When level signal input terminal HOLD terminal enters hold state, actuality, ports enter hold state half cycle later than (see Chapter Operation Timing). converter converter characteristics differ from actual characteristics because flexible cable other elements used between emulation user's target. (10) Status while program stopped system using PC4701, loop iteration address F800016 establishes maintains status during program stop. Also, when debug commands issued check edit memory data, addresses F800016 F83FF16 addresses F600016 F63FF16 used work area. this reason, when output enabled microprocessor mode, signal output.
IMPORTANT
(11) Actual output emulator output Table Actual emulator outputs
Access area area Signal Address Data RD/WR Internal area Internal area Address Data RD/WR External area Address Data RD/WR STOP state Address Data RD/WR Actual Output Output (Floating during read operations) Output (WR=Low write cycle, output RD=Low read cycle) output (High output fixed) output (Low output fixed) Output Previous status maintained Floating output (High output fixed) output (High output fixed) output (Low output fixed) output (Previous status maintained) Output Output (Inputs external data when reading) RD=Low read cycle) Output Output Output Output Output (Inputs external data when reading) RD=Low read cycle) Output Output Output Output Floating Output only Read operations High output fixed) Output Output Output Output Output Output Floating output (High output fixed) output (High output fixed) Output (High output fixed) output (High output fixed) Output M306V0T-RPD-E Output Floating Item with different outputs
Output (WR=Low write cycle, Output (WR=Low write cycle,
IMPORTANT
Notes Settings References:
details settings references, refer M3T-PD30 emulator debugger user's manual. Always area EXTERNAL. area INTERNAL. This uses bytes from 0FFFC16 0FFFF16 stack area RESET command. RESET command cannot correctly executed when these bytes cannot read written must therefore take care using resetting procedure when following condition condition true. When bytes from 0FFFC16 0FFFF16 EXTERNAL system shifting from single chip mode memory expansion mode microprocessor mode When bytes from 0FFFC16 0FFFF16 EXTERNAL system started microprocessor mode there read/write-enabled memory external area. following setting procedure when either above conditions true. bytes from bytes from 0FFFC16 0FFFF16 INTERNAL. Execute M3T-PD30 emulator debugger RESET command. stack pointer. (Example) RESET: FCLR #480H, stack pointer setting (STOP program after executing this command.)
bytes from 0FFFC16 0FFFF16 EXTERNAL.
Note Changing Data Area When Program Executed:
change data when program executed, write data when setting both 'INTERNAL' 'EXTERNAL'. Procedure With 'INTERNAL' specified, change data area. Change data MEMORY WINDOW, Script Window, etc. From script window, change setting area 'EXTERNAL' 400,FFF,EXT With 'EXTERNAL' specified, change data area. Change data MEMORY WINDOW, Script Window, etc. Change setting area 'INTERNAL' again. 400,FFF,INT (Example) When changing data area (Address: 410h) '55h'. MemoryByte( 410,55 400,FFF,EXT MemoryByte( 410,55 400,FFF,INT
IMPORTANT
Note Reading Internal Sources:
When this product configured with emulator debugger, following results occur when reading registers listed Table 1.3. Data displayed correctly, internal data affected all. Real-time tracing Data values internal source read cycle displayed correctly. Real-time monitoring Data displayed correctly. This happens because data read from internal source output external point. When data written into internal source, data input from external point displayed correctly. Table Registers signals
Register Processor mode registers System clock control registers Chip select control register Address identity interrupt enable register Protect register Supervisor timer start register Supervisor timer control register Address identity interrupt registers source pointers destination pointers transfer counters control registers Signal PM0, CM0, AIER PRCR WDTS RMAD0, RMAD1 SAR0, SAR1 DAR0, DAR1 TCR0, TCR1 DM0CON, DM1CON
Note Stack:
This product uses bytes stack.
Chapter Introduction
M306V0T-RPD-E used being connected PC4701 emulator main unit. Figure shows system configuration.
Figure System configuration
Following products attached M306V0T-RPD-E. Emulation (M306V0T-RPD-E) This emulation contains emulation memory debug functions. Flexible cable (FLX120-RPD) This 120-pin flexible cable connects PC4701 emulation pod. Flexible cable (FLX100) This 100-pin flexible cable connects emulation target system. Converter board (FLX-100LCC) This board connected socket 100LCC target system.
Chapter Specifications
Table lists specifications M306V0T-RPD-E. Table Specifications M306V0T-RPD-E
Item Usable emulator Usable Usable modes Description PC4701HS, PC4701L M16C/6V Group MCUs Single-chip mode Memory expansion mode Microprocessor mode M306V0EEFP Main clock (Xin): 10.000 Sub-clock (Xcin): 32.768 MHz, 0-wait (Vcc bytes 16-byte dump: About BCLK cycle 16-byte fill: About BCLK cycle Supplied from emulator operating voltage emulation determined detecting supply voltage target system. When target system connected, when supply voltage target system more than operating voltage 100-pin package: FLX-100LCC 35°C dew) 60°C standards (FCC part15 Class marking (EN55022, EN50082-1)
Evaluation type Emulation clock
Max. operating frequency emulation Power supply range Emulation memory Stack capacity used emulator Suspended cycles run-time debug
Power supply
Connection with target system Operating temperature range Storage temperature range Overseas standards
Chapter Settings Target Systems
Positions Switches
Figure shows positions switches M306V0T-RPD-E.
Figure Positions switches
Settings
Table gives list switch settings. Table Switch (SW) settings
Signal PORT/OSD (P57)
port
Setting
function PORT (P57)
PORT (P57)
PORT (Factory-setting) port
XCIN terminal XCIN leave unconnected XCOUT XCOUT terminal XCOUT connect XOUT terminal XCOUT XCIN
P87/XCIN
XCIN
(Factory-setting) port
P86/XCOUT
XCOUT
(Factory-setting) open
XOUT
OPEN
XOUT
OPEN XOUT
XOUT
OPEN (Factory-setting) With pullup resistor (HOLD/RDY)
Without pullup resistor OPEN XOUT
P55/HOLD P57/RDY
OPEN
(Factory-setting) pull down leave unconnected
pull
CNVss
(Factory-setting) pull down leave unconnected
pull Without pullup resistor OPEN
BYTE
(Factory-setting) With pullup resistor
P70/71
OPEN
OPEN (Factory-setting)
Leave PORT position.
IMPORTANT
Note Switch Settings:
sure turn power before setting switches. Otherwise, internal circuits damaged.
Procedure Setting Oscillation Frequency
using emulation pod's internal oscillator, below. using target system's oscillator, page Using emulation pod's oscillator M306V0T-RPD-E available with types internal oscillator circuits: OSC-3 oscillator board (preinstalled M306V0T-RPD-E): OSC-2 oscillator board (bare board) OSC-3 oscillator board M306V0T-RPD-E equipped with 10MHz internal oscillator board. running M306V0T-RPD-E MHz, OSC-3 oscillator board shipped with. OSC-2 oscillator board M306V0T-RPD-E supplied with oscillator circuit bare board (connector mounting). using M306V0T-RPD-E with internal oscillation frequencies other than those permitted standard OSC-3 oscillator board, create desired oscillator circuit OSC2 bare board replace OSC-3 board with OSC-2 board. Figure shows external dimensions connector layout OSC-2 oscillator board. Figure shows OSC-2 circuit. circuit constants recommended maker oscillator circuit.
J1-4: J1-3: Oscillator output J1-2: J1-1:
Figure External view oscillator bare board OSC-2 connector assignments
J1-3
J1-1
J1-2 J1-4
IC1: Inverter (Unbuffer)
5.08-mm-pitch 2-pin oscillator 2.54-mm-pitch 2-pin oscillator 2.54-mm-pitch 3-pin oscillator Figure Circuit oscillator board OSC-2
Figure shows replace oscillator board. Remove screw locking oscillator board place. Lift board directly product. Plug connector oscillator board into connector M306V0T-RPDE board. Lock board M306V0T-RPD-E board with screw.
Figure Replacing oscillator board
Using target system's oscillator operate emulator with external clock, construct oscillation circuit shown Figure target system input oscillation output 40-60% duty (within operating range emulator's MCU) into (Xcin) pin. Make note fact that oscillation circuit shown Figure where resonator connected between (Xcin) Xout (Xcout) pins, oscillation does occur because flexible cable, buffer other devices used between evaluation target system. M3T-PD30 emulator debugger EXT. details, M3T-PD30 emulator debugger user's manual.
Figure External oscillator circuit
Figure Circuit oscillation this
Data Slicer Signals Clock Signal Circuits
Figure shows layout parts board circuit diagrams used data slicing clock circuits.
Figure Layout parts
Figure shows part numbers constants parts signal CVIN.
Figure CVIN signal circuit
Figure shows part numbers constants parts signal HLF.
Figure signal circuit
Figure 4.10 shows part numbers constants parts signal VHOLD.
Figure 4.10 VHOLD signal circuit
Figure 4.11 shows part numbers constants parts signal OSC1, OSC2.
Figure 4.11 OSC1, OSC2 signal circuit
Procedure Setting Switches
must remove cover M306V0T-RPD-E order switches. remove four screws holding cover. There screws each side (see Figure 4.12). sure turn power before attempting change switch settings. power damage circuits.
Figure 4.12 Removing M306V0T-RPD-E cover
After removing cover, switches referring Table (page 19). After setting switches, replace cover reversing procedure removal. Replace M306V0T-RPD-E cover. Replace screws (two each side) holding M306V0T-RPD-E cover place.
Procedure Writing File
need change contents file, depending being developed. file same directory emulator debugger. file name M30620.MCU M16C/6V group MCUs. file contains following information: area, internal area, internal area, firmware filename. these according being developed. your editor edit file.
area starting address area ending address
2C00 Internal starting address 3FFF Internal ending address F0000 Internal starting address FFFFFInternal ending address M30620B Firmware filename edit.)
Chapter Method Connection
Connecting Emulator Main Unit
FLX120-RPD 120-pin flexible cable connect emulator main unit M306V0T-RPDE. Figure shows connect emulator main unit FLX120-RPD.
Figure Connecting emulator main unit FLX120-RPD
Connect FLX120-RPD with M306V0T-RPD-E. Figure shows connect M306V0T-RPDE FLX120-RPD.
Figure Connecting M306V0T-RPD-E FLX120-RPD
CAUTION
Note Connecting Cable:
Always shut power before connecting cable. power state could destroy internal circuits.
Connecting Target System
Figure shows connections between emulator probes target systems. more details, refer "Renesas Tools Accessory Guide".
Figure Connection target systems
CAUTION
Notes Connecting Target Systems:
sure turn power before making connections. Otherwise, internal circuits damaged. small connectors FLX100 FLX-100LCC guaranteed only insertion/removal iterations.
Chapter Constraints
instruction instruction cannot used. Software hardware breaks simultaneous software hardware breaks. software breaks areas which setting EXTERNAL. Using multiplex with PC4701L emulator only Fetch hardware break condition multiplex area. Using address match interrupts software break same address have address match interrupt. hardware break within bytes leading address which address match interrupt invoked. When address which address match interrupt occurs achieved one-step execution, address match interrupt processing first command return from interrupt executed simultaneously. Software resets software resets. Watchdog function using watchdog function, only program execution. want debugger functions other than program execution, disable watchdog function.
Chapter Operation Timing (Memory Expansion Microprocessor Modes)
Separate wait)
Table Figure show timing when using memory expansion mode microprocessor mode (separate bus, wait). Table Memory expansion mode microprocessor mode (separate bus, wait)
Symbol Parameter M306V0EEFP [ns] Min. td(BCLK-AD) th(BCLK-AD) th(RD-AD) th(WR-AD) td(BCLK-CS) th(BCLK-CS) td(BCLK-ALE) th(BCLK-ALE) td(BCLK-RD) th(BCLK-RD) td(BCLK-WR) th(BCLK-WR) td(BCLK-DB) th(BCLK-DB) td(DB-WR) th(WR-DB) Address output delay time Address output hold time (BCLK) Address output hold time (RD) Address output hold time (WR) Chip-select output delay time Chip-select output hold time (BCLK) signal output delay time signal output hold time signal output delay time signal output hold time signal output delay time signal output hold time Data output delay time (BCLK) Data output hold time (BCLK) Data output delay time (WR) Data output hold time (WR) (Note Max. M306V0T-RPD-E [ns] Min. (Note Max.
Note Compute timing according BCLK frequency. below formula. td(DB-WR) [ns] f(BCLK)x2 [ns] f(BCLK)x2
Note Compute timing according BCLK frequency. below formula. td(DB-WR)
Memory expansion mode microprocessor mode wait) Read timing
Write timing
Measurement Condition Input timing voltage: Output timing voltage:
Figure Memory expansion mode microprocessor mode (separate bus, wait)
Separate (with wait), When Accessing External Memory Area
Table Figure show timing when using memory expansion mode microprocessor mode (with wait, when accessing external memory area). Table Memory expansion mode microprocessor mode (separate bus, with wait)
Symbol Parameter M306V0EEFP [ns] Min. td(BCLK-AD) th(BCLK-AD) th(RD-AD) th(WR-AD) td(BCLK-CS) th(BCLK-CS) td(BCLK-ALE) th(BCLK-ALE) td(BCLK-RD) th(BCLK-RD) td(BCLK-WR) th(BCLK-WR) td(BCLK-DB) th(BCLK-DB) td(DB-WR) th(WR-DB) Address output delay time Address output hold time (BCLK) Address output hold time (RD) Address output hold time (WR) Chip-select output delay time Chip-select output hold time (BCLK) signal output delay time signal output hold time signal output delay time signal output hold time signal output delay time signal output hold time Data output delay time (BCLK) Data output hold time (BCLK) Data output delay time (WR) Data output hold time (WR) (Note Max. M306V0T-RPD-E [ns] Min. (Note Max.
Note Compute timing according BCLK frequency. below formula. td(DB-WR) [ns] f(BCLK)x2 [ns] f(BCLK)x2
Note Compute timing according BCLK frequency. below formula. td(DB-WR)
Memory expansion mode microprocessor mode (with wait, when accessing external memory area) Read timing
Write timing
Measurement Condition Input timing voltage: VIH= Output timing voltage:
Figure Memory expansion mode microprocessor mode (separate bus, with wait)
Multiplex (with wait), When Accessing External Memory Area
Table Figure show timing when using memory expansion mode microprocessor mode (with wait, when accessing external memory area). Table Memory expansion mode microprocessor mode (multiplex bus, with wait)
M306V0EEFP [ns] Min. td(BCLK-AD) th(BCLK-AD) th(RD-AD) th(WR-AD) td(BCLK-CS) th(BCLK-CS) th(RD-CS) th(WR-CS) td(BCLK-RD) th(BCLK-RD) td(BCLK-WR) th(BCLK-WR) td(BCLK-DB) th(BCLK-DB) td(DB-WR) th(WR-DB) td(BCLK-ALE) th(BCLK-ALE) td(AD-ALE) th(ALE-AD) td(AD-RD) td(AD-WR) tdz(RD-AD) Address output delay time Address output hold time (BCLK) Address output hold time (RD) Address output hold time (WR) Chip-select output delay time Chip-select output hold time (BCLK) Chip-select output hold time (RD) Chip-select output hold time (WR) signal output delay time signal output hold time signal output delay time signal output hold time Data output delay time (BCLK) Data output hold time (BCLK) Data output delay time (WR) Data output hold time (WR) signal output delay time (BCLK) signal output hold time (BCLK) (Note (Note (Note (Note (Note (Note Max. M306V0T-RPD-E [ns] Min. (Note (Note (Note (Note (Note (Note (Note Max.
Symbol
Parameter
signal output delay time (ADDRESS) (Note signal output hold time (ADDRESS) signal output hold time (ADDRESS) signal output hold time (ADDRESS) signal output hold time (ADDRESS)
Note Compute timing according BCLK frequency. below formula. th(RD-AD) th(RW-AD) th(RD-CS) th(WR-CS) f(BCLK)x2 f(BCLK)x2 f(BCLK)x2 f(BCLK)x2 [ns] [ns] [ns] [ns] td(DB-WR) th(WR-DB) td(DB-WR) 109x3 [ns] f(BCLK)x2 f(BCLK)x2 [ns]
[ns] f(BCLK)x2
Note Compute timing according BCLK frequency. below formula. th(RD-AD) th(RW-AD) th(RD-CS) th(WR-CS) [ns] f(BCLK)x2 [ns] f(BCLK)x2 [ns] f(BCLK)x2 [ns] f(BCLK)x2 td(DB-WR) th(WR-DB) td(DB-WR) 109x3 [ns] f(BCLK)x2 [ns] f(BCLK)x2 [ns] f(BCLK)x2
Memory expansion mode microprocessor mode (with wait, when accessing external memory area) Read timing
Write timing
Measurement Condition Input timing voltage: Output timing voltage:
Figure Memory expansion mode microprocessor mode (multiplex bus, with wait)
Timing Requirements
Table Figure show timing requirements when using memory expansion mode microprocessor mode. Table Timing requirements (Vcc
Symbol Parameter M306V0EEFP [ns] Min. tsu(DB-RD) Data input setup time Max. M306V0T-RPD-E [ns] Min. (Note Max.
tsu(RDY-BCLK) input setup time tsu(HOLD-BCLK) HOLD input setup time th(RD-DB) th(BCLK-RDY) Data input hold time input hold time
th(BCLK-HOLD) HOLD input hold time th(BCLK-HLDA) HLDA output delay time
Note tsu(HOLD-BCLK)
109x3 f(BCLK)x2
Memory expansion mode microprocessor mode
Note will high-impedance status regardless input level BYTE ports function selection (PM06) processor mode register Note This product will high-impedance delaying cycles than actual MCU. Measurement Condition Input timing voltage: Output timing voltage:
Figure Timing requirements (Vcc
Chapter Electrical Characteristics
Tables show electrical characteristics user's interface. Table Electrical characteristics 74HC4066FS (P00 P52)
Standard value Symbol Parameter VIHC level control input voltage Min. 3.15 Typ. 2000 Max. 1.35 Unit
VILC
level control input voltage
resistance resistance difference between arbitrary switches package Switch input/output leakage current
IOFF
Table Electrical characteristics M60074-0111FP (P53 P57,
Standard value Symbol Parameter Min. VTVT+ IOZH IOZL 1.25 4.95 Typ. Max. 0.05 Unit
Input voltage
level output voltage level output voltage level output current level output current level input current level input current state level output current state level output current Input/output terminal capacity
Chapter Maintenance Guarantee
Maintenance
dust dirt collects equipment your emulation system, wipe with soft cloth. thinner other solvents because these chemicals cause equipment's surface coating separate.
Guarantee
your product becomes faulty within year after purchase while being used under good conditions observing "Precautions Safety" described Chapter this user's manual, will repair replace your faulty product free charge. Note, however, that your product's fault raised following causes, will repair replace with with extra-charge: Misuse, abuse, under extraordinary conditions Unauthorized repair, remodeling, maintenance, Inadequate user's system misuse Fires, earthquakes, other unexpected disasters above cases, contact your local distributor. your product being leased, consult leasing company owner.
Repair Provisions
Repair with extra-charge products elapsed more than year after purchase repaired with extra-charge. Replacement with extra-charge your product's fault falls following categories, fault will corrected replacing entire product instead repair, will advised purchase one, depending severity fault. Faulty broken mechanical portions Flaw, separation, rust coated plated portions Flaw cracks plastic portions Faults breakage caused improper unauthorized repair modification Heavily damaged electric circuits overvoltage, overcurrent shorting power supply Cracks printed circuit board burnt-down patterns Wide range faults that makes replacement less expensive than repair Unlocatable unidentified faults Expiration repair period When period year elapses after model dropped from production, repairing products model become impossible. Transportation fees sending your product repair Please send your product repair your expense.
Request Repair
your product found faulty, follow procedure below send your product repair.
Customer
Fill Repair Request Sheet included with this product, then send along with this product repair your local distributor. Make sure that information Repair Request Sheet written much detail possible facilitate repair.
Distributor
After checking contents fault, distributor should please send faulty product along with Repair Request Sheet Renesas Solutions Corp.
Renesas Solutions
When faulty product repaired, will returned customer earliest convenience.
CAUTION
Note Transporting Product:
When sending your product repair, packing cushion material supplied with this product when delivered specify handling caution handled precision equipment. packing your product complete, damaged during transportation. When pack your product bag, make sure conductive polyvinyl supplied with this product (usually blue bag). When other bags, they cause trouble your product because static electricity.
Chapter Troubleshooting
10.1 When M306V0T-RPD-E Does Work Properly
Emulator main unit cannot powered Check power cord firmly plugged into receptacle. Check power 3P-2P converting connector firmly connected.
M306V0T-RPD-E does start when target system connected with PC4701 system. (The Error emulator main unit lights up.) Check described above. Check whether emulator main unit FLX120-RPD firmly connected. Check whether FLX120-RPD M306V0T-RPD-E firmly connected. Check whether M306V0T-RPD-E target system firmly connected. Check whether power supplied target system. Check whether switches M306V0T-RPD-E firmly set. (Refer Chapter setting switches.) Check whether RESET held 'HIGH' when target system connected. Check whether HOLD held 'HIGH' when microprocessor memory expansion mode. Check whether oscillator circuit target system oscillating correctly when using target's oscillator. Check whether correct firmware downloaded emulator main unit. (Refer user's manual emulator debugger about download firmware.)
PC4701 system does pass self-checks (excluding when target system error occurs), there possibility trouble system. such case, contact place purchase. Please take note that self-check should executed under following conditions. target system connected. Switch position, '16' (See Chapter When condition does improve even check items above, troubles described below considered. Trouble evaluation Trouble M306V0T-RPD-E Trouble PC4701 emulator main unit
Appendix External Dimensions
External Dimensions M306V0T-RPD-E
Unit: Figure External dimensions M306V0T-RPD-E
External Dimensions FLX-100LCC
Unit: Figure External dimensions FLX-100LCC
Appendix Connection Diagrams
Figures show connection diagrams M306V0T-RPD-E. These connection diagrams mainly show interface section with target system, circuits which connected target system such emulator's control system omitted.
Figure Connection diagram M306V0T-RPD-E (1/2)
Figure Connection diagram M306V0T-RPD-E (2/2)
M306V0T-RPD-E User's Manual
Rev.1.00 October 2003 REJ10J0380-0100Z COPYRIGHT ©2003 RENESAS TECHNOLOGY CORPORATION RENESAS SOLUTIONS CORPORATION RIGHTS RESERVED
Other recent searches
TGA4509-SM - TGA4509-SM TGA4509-SM Datasheet
TDA7309 - TDA7309 TDA7309 Datasheet
SNC80000 - SNC80000 SNC80000 Datasheet
IRHF7430SE - IRHF7430SE IRHF7430SE Datasheet
IRFR - IRFR IRFR Datasheet
U9120N - U9120N U9120N Datasheet
HFA3860A - HFA3860A HFA3860A Datasheet
HCS301 - HCS301 HCS301 Datasheet
HCF4009UB - HCF4009UB HCF4009UB Datasheet
DSE-195-034 - DSE-195-034 DSE-195-034 Datasheet
Privacy Policy | Disclaimer
© 2012 Datasheet Archive
