User's Manual HS3937ECH61HE(B) Renesas neither warrants gran
|
|
|
Top Searches for this datasheet
H8/3937R H8/33937 Series TFP-100B User System Interface Cable (HS3937ECH61H) E6000 Emulator
User's Manual
HS3937ECH61HE(B)
Renesas neither warrants grants licenses rights Renesas's third party's patent, copyright, trademark, other intellectual property rights information contained this document. Renesas bears responsibility problems that arise with third party's rights, including intellectual property rights, connection with information contained this document. Products product specifications subject change without notice. Confirm that have received latest product standards specifications before final design, purchase use. Renesas makes every attempt ensure that products high quality reliability. However, contact Renesas's sales office before using product application that demands especially high quality reliability where failure malfunction directly threaten human life cause risk bodily injury, such aerospace, aeronautics, nuclear power, combustion control, transportation, traffic, safety equipment medical equipment life support. Design your application that product used within ranges guaranteed Renesas particularly maximum rating, operating supply voltage range, heat radiation characteristics, installation conditions other characteristics. Renesas bears responsibility failure damage when used beyond guaranteed ranges. Even within guaranteed ranges, consider normally foreseeable failure rates failure modes semiconductor devices employ systemic measures such fail-safes, that equipment incorporating Renesas product does cause bodily injury, fire other consequential damage operation Renesas product. This product designed radiation resistant. permitted reproduce duplicate, form, whole part this document without written approval from Renesas. Contact Renesas's sales office questions regarding this document Renesas semiconductor products.
Preface
Thank purchasing this user system interface cable (HS3937ECH61H) Renesas's original microcomputer H8/3937R H8/3937 series. HS3937ECH61H user system interface cable that connects H8/300L series E6000 emulator (HS388REPI60H; hereinafter referred emulator) through expansion board socket TFP-100B package H8/3937R H8/3937 series user system.
Contents
Section
Configuration.1
Section Connection Procedures
Connecting User System Interface Cable Emulator Station Connecting User System Interface Cable User System 2.2.1 Installing Socket 2.2.2 Soldering Socket 2.2.3 Inserting Cable Head 2.2.4 Fastening Cable Head 2.2.5 Fastening Cable Body. Recommended Dimensions User System Mount Dimensions User System Interface Cable Head. Resulting Dimensions after Connecting User System Interface Cable
Section Installing User System.12 Section Verifying Operation.14 Section Notice
Section
Configuration
CAUTION
IC149-100-054-B51 socket (manufactured YAMAICHI ELECTRONICS Co., Ltd.) TFP-100B package socket user system.
Figure shows configuration HS3937ECH61H user system interface cable TFP-100B package.
Figure HS3937ECH61H User System Interface Cable
Table lists HS3937ECH61H components. Please make sure have these components when unpacking. Table HS3937ECH61H Components
Quantity TFP-100B package installing TFP-100B packaged fastening cable head installing TFP-100B packaged User's manual HS3937ECH61H (this manual) Remarks Flat cable
Component Cable body Cable head socket Socket cover Screws (M2.6 Screws (M2.6 Documentation
Section Connection Procedures
Connecting User System Interface Cable Emulator Station
WARNING
Observe precautions listed below. Failure will result FIRE HAZARD will damage user system emulator product will result PERSONAL INJURY. USER PROGRAM will LOST. Always switch user system emulator product before USER SYSTEM INTERFACE CABLE connected removed from part. Before connecting, make sure that both sides correctly aligned. user system interface cable dedicated emulator must used.
connect cable body emulator station, follow instructions below. Make sure user system emulator station turned off.
CAUTION
When connecting removing user system interface cable, apply force only direction suitable connection removal, while making sure bend twist cable connectors. Otherwise, connectors will damaged. user system interface cable must connected H8/300L Series E6000 emulator through H8/3937 Series expansion board. connect user system interface cable directly E6000 emulator.
After making sure direction expansion board connector labeled E6000 EMULATOR correct, firmly insert expansion board connector into emulator station connector ([1] figure Connect expansion board labeled USER INTERFACE CABLE user system interface cable body.
Emulator station
Expansion board
Subclock selection User system interface cable
Figure Connecting User System Interface Cable Expansion Board
Cable body connector
Connecting User System Interface Cable User System
WARNING
Always switch user system emulator product before USER SYSTEM INTERFACE CABLE connected removed from part. Before connecting, make sure that both sides correctly aligned. Failure will result FIRE HAZARD will damage user system expansion board will result PERSONAL INJURY. USER PROGRAM will LOST.
connect cable head user system, follow instructions below. 2.2.1 Installing Socket
After checking location socket, apply epoxy resin adhesive bottom socket TFP-100B package, fasten user system before soldering. 2.2.2 Soldering Socket
After fastening, solder socket TFP-100B package user system. sure completely solder leads that solder slops gently over leads forms solder fillets. (Use slightly more solder than MCU.)
2.2.3
Inserting Cable Head
CAUTION
Check location before inserting.
Align socket TFP-100B package user system with user system interface cable head, insert user system interface cable head into socket user system, shown figure 2.2.4 Fastening Cable Head
CAUTION
Philips-type screwdriver whose head matches screw head. tightening torque must 0.054 less. applied torque cannot accurately measured, stop tightening when force required turn screw becomes significantly greater than that needed when first tightening. screw tightened much, screw head break socket contact error caused crack socket solder. emulator does operate correctly, cracks might have occurred solder. Check conduction with tester re-solder socket necessary.
Fasten user system interface cable head socket TFP-100B package user system with four screws (M2.6 with flat washers) provided. Each screw should tightened little time, alternating between screws opposing corners. Take special care, such manually securing socket soldered area, prevent soldered socket from being damaged overtightening screws twisting components.
Cable head
User system
Figure Connecting User System Interface Cable User System
2.2.5
Fastening Cable Body
Connect cable body cable head.
Cable body Removing Push remove
Remove
Cable head
User system
Figure Fastening Cable Body
Recommended Dimensions User System Mount
Figure shows recommended dimensions mount (footprint) user system with socket TFP-100B package (IC149-100-054-B51: manufactured YAMAICHI ELECTRONICS Co., Ltd.). Note that dimensions figure somewhat different from those actual chip's mount pad.
Figure Recommended Dimensions Mount
Dimensions User System Interface Cable Head
dimensions user system interface cable head shown figure
Figure Dimensions User System Interface Cable Head
Resulting Dimensions after Connecting User System Interface Cable
resulting dimensions, after connecting user system interface cable head user system, shown figure
Figure Resulting Dimensions after Connecting User System Interface Cable
Section Installing User System
CAUTION
Check location before inserting. Philips-type screwdriver whose head matches screw head. tightening torque must 0.054 less. applied torque cannot accurately measured, stop tightening when force required turn screw becomes significantly greater than that needed when first tightening. screw tightened much, screw head break socket contact error caused crack socket solder. does operate correctly, cracks might have occurred solder. Check conduction with tester re-solder socket necessary.
Check location before inserting into socket user system, shown figure After inserting MCU, fasten socket cover with provided four screws (M2.6 with flat washers). Take special care, such manually securing socket soldered area, prevent socket from being damaged overtightening screws twisting components.
Figure Installing User System
Section Verifying Operation
When using H8/300L series E6000 emulator (HS388REPI60H), turn emulator according procedures described H8/300L Series E6000 Emulator User's Manual (HS388REPI60HE). Verify user system interface cable connections accessing ports checking states pins. error detected, recheck soldered socket location System Clock (OSC2, When system clock selected Configuration Window jumper user system interface cable, system clocks table selected (see figures 10). Table Setting System Clocks
Configuration Window Target/2 User System Interface Cable (P4) setting either pins connected. connected connected System Clock Target clock/2
Subclock (DX2, When switch expansion board (Subclock selection) jumper user system interface cable, subclocks table selected. Select target subclock Configuration window (see figures 10). Table Setting Subclocks
Expansion Board (Subclock selection) 76.8 setting subclock selection switch either 76.8 kHz. connected User System Interface Cable (P5) connected Subclock (fW) 76.8 Target subclock
Figure shows Expansion board Subclock Selection, figure shows location jumpers Figure shows system clock oscillator user system interface cable subclock input specifications.
Subclock selection
Figure Expansion board Subclock Selection
Figure Jumpers
Figure System Clock Oscillator Subclock Input Specifications
Section Notice
Make sure that user system socket correctly aligned with cable head before inserting cable head into user system socket. dimensions recommended mount user system socket different from those MCU. avoid breaking wires cable body, place heavy sharp metal objects user system interface cable. While emulator station connected user system with user system interface cable, force must applied cable head. Position emulator station, user system interface cable, user system shown figure
Figure User System Interface Cable Location Example jumper used testing. remove inserted jumper pin.
Figure Jumper
Other recent searches
TMS320C20x - TMS320C20x TMS320C20x Datasheet
STi3220 - STi3220 STi3220 Datasheet
STB55NE06L - STB55NE06L STB55NE06L Datasheet
LM4832 - LM4832 LM4832 Datasheet
74LVC04A - 74LVC04A 74LVC04A Datasheet
Privacy Policy | Disclaimer
© 2012 Datasheet Archive
