User's Manual HS2646ECH61HE(B) Renesas neither warrants gran

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

User's Manual HS2646ECH61HE(B) Renesas neither warrants gran

Datasheet Thumbnail

Top Searches for this datasheet

H8S/2646 Series FP-144 User System Interface Cable (HS2646ECH61H) E6000 Emulator
User's Manual
HS2646ECH61HE(B)
Renesas neither warrants grants licenses rights Renesas's third party's patent, copyright, trademark, other intellectual property rights information contained this document. Renesas bears responsibility problems that arise with third party's rights, including intellectual property rights, connection with information contained this document. Products product specifications subject change without notice. Confirm that have received latest product standards specifications before final design, purchase use. Renesas makes every attempt ensure that products high quality reliability. However, contact Renesas's sales office before using product application that demands especially high quality reliability where failure malfunction directly threaten human life cause risk bodily injury, such aerospace, aeronautics, nuclear power, combustion control, transportation, traffic, safety equipment medical equipment life support. Design your application that product used within ranges guaranteed Renesas particularly maximum rating, operating supply voltage range, heat radiation characteristics, installation conditions other characteristics. Renesas bears responsibility failure damage when used beyond guaranteed ranges. Even within guaranteed ranges, consider normally foreseeable failure rates failure modes semiconductor devices employ systemic measures such fail-safes, that equipment incorporating Renesas product does cause bodily injury, fire other consequential damage operation Renesas product. This product designed radiation resistant. permitted reproduce duplicate, form, whole part this document without written approval from Renesas. Contact Renesas's sales office questions regarding this document Renesas semiconductor products.
Preface
Thank purchasing this user system interface cable (HS2646ECH61H) Renesas's original microcomputer H8S/2646 series. HS2646ECH61H user system interface cable that connects H8S/2636 H8S/2646 series E6000 emulator (HS2646EPI61H; hereinafter referred emulator) socket FP-144 package H8S/2646 series user system.
Contents
Section Configuration Section Connection Procedures
Connecting User System Interface Cable Emulator Station Connecting User System Interface Cable User System 2.2.1 Installing Socket 2.2.2 Inserting Cable Head 2.2.3 Fastening Cable Head 2.2.4 Fastening Cable Body. Recommended Dimensions User System Mount Dimensions User System Interface Cable Head. Resulting Dimensions after Connecting User System Interface Cable
Section Installing User System.13 Section Verifying Operation.15 Section Notice
Section Configuration
CAUTION
NQPACK144SD socket (manufactured Tokyo Eletech Corporation) FP-144 package socket user system.
Figure shows configuration HS2646ECH61H user system interface cable FP-144 package.
Figure
HS2646ECH61H User System Interface Cable
Table lists HS2646ECH61H components. Please make sure have these components when unpacking. Table HS2646ECH61H Components
Quantity FP-144 package installing FP-144 packaged fastening cable head installing FP-144 packaged determining socket location tightening screws User's manual HS2646ECH61H (this manual) Remarks Flat cable
Component Cable body Cable head socket Socket cover Screws Screws Guide pins Screwdriver Documentation
Section Connection Procedures
Connecting User System Interface Cable Emulator Station
WARNING
Observe precautions listed below. Failure will result FIRE HAZARD will damage user system emulator product will result PERSONAL INJURY. USER PROGRAM will LOST. Always switch user system emulator product before USER SYSTEM INTERFACE CABLE connected removed from part. Before connecting, make sure that both sides correctly aligned. user system interface cable dedicated emulator must used.
connect cable body emulator station, follow instructions below. Make sure user system emulator station turned off.
CAUTION
When connecting removing user system interface cable, apply force only direction suitable connection removal, while making sure bend twist cable connectors. Otherwise, connectors will damaged.
After making sure direction cable body connector correct, firmly insert cable body connector into emulator station socket (figure
Emulator station
Cable body connector User system interface cable
Figure
Connecting User System Interface Cable Emulator Station
Connecting User System Interface Cable User System
WARNING
Always switch user system emulator product before USER SYSTEM INTERFACE CABLE connected removed from part. Before connecting, make sure that both sides correctly aligned. Failure will result FIRE HAZARD will damage user system emulator product will result PERSONAL INJURY. USER PROGRAM will LOST.
connect cable head user system, follow instructions below. 2.2.1 Installing Socket
Confirming location socket
CAUTION
After confirming location socket, apply epoxy resin adhesive four projections bottom socket, fasten user system.
guide pins provided determine where install socket, shown figure
Guide pins
projections apply epoxy resin adhesive
socket (NQPACK144SD manufactured Tokyo Eletech Corporation)
Bottom view soket
User system
Figure
Location Setting Socket
Solder socket FP-144 package user system.
CAUTION
sure completely solder leads that solder slops gently over leads forms solder fillets. (Use slightly more solder than MCU.)
2.2.2
Inserting Cable Head
CAUTION
Check location before inserting.
Align socket FP-144 system interface cable head into socket user system, shown figure
2.2.3
Fastening Cable Head
CAUTION
Philips-type screwdriver whose head matches screw head. tightening torque must 0.054 less. applied torque cannot accurately measured, stop tightening when force required turn screw becomes significantly greater than that needed when first tightening. screw tightened much, screw head break socket contact error caused crack socket solder. emulator does operate correctly, cracks might have occurred solder. Check conduction with tester re-solder socket necessary.
Fasten user system interface cable head socket FP-144 package user system with four screws provided. Each screw should tightened little time, alternating between screws opposing corners. Take special care, such manually securing socket soldered area, prevent soldered socket from being damaged overtightening screws twisting components.
Screws 10mm)
Cable head socket (NQPACK144SD manufactured User system Tokyo Eletech Coporation)
Figure
Connecting User System Interface Cable User System
2.2.4
Fastening Cable Body
Connect cable body cable head.
Cable body Removing
Push remove
Remove
Cable head
User system
Figure
Fastening Cable Body
Recommended Dimensions User System Mount
Figure shows recommended dimensions mount (footprint) user system with socket FP-144 package (NQPACK144SD: manufactured Tokyo Eletech Corporation). Note that dimensions figure somewhat different from those actual chip's mount pad.
23.00 0.15
11.50
11.50
2.00 ±0.10
0.50
0.25 (max.) Unit: Tolerance: ±0.10 unless otherwise specified
Figure
Recommended Dimensions Mount
0.50
23.00 0.15
Dimensions User System Interface Cable Head
dimensions user system interface cable head shown figure
Figure
Dimensions User System Interface Cable Head
Resulting Dimensions after Connecting User System Interface Cable
resulting dimensions, after connecting user system interface cable head user system, shown figure
Figure
Resulting Dimensions after Connecting User System Interface Cable
Section Installing User System
CAUTION
Check location before inserting. Philips-type screwdriver whose head matches screw head. tightening torque must 0.054 less. applied torque cannot accurately measured, stop tightening when force required turn screw becomes significantly greater than that needed when first tightening. screw tightened much, screw head break socket contact error caused crack socket solder. does operate correctly, cracks might have occurred solder. Check conduction with tester re-solder socket necessary.
Check location before inserting into socket user system, shown figure After inserting MCU, fasten socket cover with provided four screws mm). Take special care, such manually securing socket soldered area, prevent socket from being damaged overtightening screws twisting components.
Screws
Socket cover
User system
socket (NQPACK144SD manufactured Tokyo Eletech Corporation)
Figure
Installing User System
Section Verifying Operation
When using E6000 emulator H8S/2646 series, turn emulator according procedures described E6000 Series Emulator User's Manual (HS2000EPI61HE). Verify user system interface cable connections accessing external memory ports check states pins with MEMORY_FILL command (emulator command). error detected, recheck soldered socket location emulator connected this user system interface cable supports kinds clock sources clock: emulator internal clock external clock user system. details, refer Emulator Supplementary Information (HS2646EPI61HE). emulator internal clock Select clock emulator station system clock using CLOCK command (emulator command). external clock user system Select target clock system clock using CLOCK command (emulator command). Supply external clock from user system emulator inputting external clock from EXTAL cable head connecting crystal oscillator EXTAL XTAL terminals. details, refer section Clock Pulse Generator, H8S/2646 F-ZTATHardware Manual. Figure shows oscillator circuit user system interface cable.
HCU04 HCU04 EXTAL XTAL HCU04 E6000 emulator
Figure Oscillator Circuit
Section Notice
Make sure that user system socket correctly aligned with cable head before inserting cable head into user system socket. dimensions recommended mount user system socket different from those MCU. This user system interface cable specifically designed HS2646EPI61H emulator. this cable with other emulator station. prevent breaking wires cable body, place heavy sharp metal objects user system interface cable. While emulator station connected user system with user system interface cable, force must applied cable head. Place emulator station, user system interface cable, user system shown example figure
Figure User System Interface Cable Location Example jumper connector used testing. remove inserted jumper pin.
Figure Short Connector

User's Manual HS2646ECH61HE(B) Renesas neither warrants gran

Top Searches for this datasheet

Other recent searches