PHASE CONTROL THYRISTORS Hockey Version Center amplifying gate Me
|
|
|
Top Searches for this datasheet
ST230C.C SERIES
PHASE CONTROL THYRISTORS Hockey Version
Center amplifying gate Metal case with ceramic insulator International standard case TO-200AB (A-PUK)
410A
TypicalApplications
motor controls Controlled power supplies controllers
Major Ratings Characteristics
Parameters
IT(AV) IT(RMS) ITSM 50Hz 60Hz 50Hz 60Hz DRM/V typical
case style TO-200AB (A-PUK)
Units
KA2s KA2s
ST230C.C
5700 5970 1600
www.irf.com
ST230C.C Series
ELECTRICAL SPECIFICATIONS Voltage Ratings
Voltage Type number Code
ST230C.C
DRM/V RRM, max. repetitive peak off-state voltage
1200 1400 1600
VRSM maximum nonrepetitive peak voltage
1300 1500 1700
DRM/I max.
On-state Conduction
Parameter
IT(AV) Max. average on-state current Heatsink temperature IT(RMS) Max. on-state current ITSM Max. peak, one-cycle non-repetitive surge current
ST230C.C
(165) (85) 5700 5970 4800 5000
Units Conditions
180° conduction, half sine wave double side (single side) cooled 25°C heatsink temperature double side cooled 10ms 8.3ms 10ms 8.3ms 10ms 8.3ms 10ms 8.3ms KA2s voltage reapplied 100% VRRM reapplied voltage reapplied 100% VRRM reapplied Sinusoidal half wave, Initial max.
Maximum fusing
Maximum fusing
1630 0.92
10ms, voltage reapplied (16.7% IT(AV) IT(AV)), max.
T(TO)1 level value threshold voltage T(TO)2 High level value threshold voltage level value on-state slope resistance High level value on-state slope resistance Max. on-state voltage Maximum holding current Max. (typical) latching current
0.98 IT(AV)),TJ max. (16.7% IT(AV) IT(AV)), max. 0.81 1.69 1000 (300) 25°C, anode supply resistive load IT(AV)),TJ max. 880A, max, 10ms sine pulse
0.88
Switching
Parameter
di/dt Max. non-repetitive rate rise turned-on current
ST230C.C
1000
Units Conditions
A/µs Gate drive 20V, max, anode voltage VDRM
Typical delay time Typical turn-off time
Gate current 1A/µs 0.67% VDRM, 25°C 300A, max, di/dt 20A/µs, dv/dt 20V/µs, Gate 100, 500µs
www.irf.com
ST230C.C Series
Blocking
Parameter
dv/dt IDRM IRRM Maximum critical rate rise off-state voltage Max. peak reverse off-state leakage current
ST230C.C
Units Conditions
V/µs max. linear rated max, rated VDRM applied
Triggering
Parameter
Maximum peak gate power
ST230C.C
10.0
Units Conditions
max, max, 50Hz, max,
PG(AV) Maximum average gate power Max. peak positive gate current +VGM Maximum peak positive gate voltage -VGM Maximum peak negative gate voltage TYP. gate current required trigger gate voltage required trigger gate current trigger gate voltage trigger
MAX. 0.25
max,
40°C 25°C 125°C 40°C 25°C 125°C Max. gate current/voltage trigger max. value which will trigger unit with rated VDRM anode-to-cathode applied Max. required gate trigger/ current/ voltage lowest value which will trigger units anode-to-cathode applied
Thermal Mechanical Specification
Parameter
Tstg Max. operating temperature range Max. storage temperature range
ST230C.C
0.17 0.08 0.033 0.017 4900 (500)
Units
Conditions
RthJ-hs Max. thermal resistance, junction heatsink RthC-hs Max. thermal resistance, case heatsink Mounting force,
operation single side cooled operation double side cooled operation single side cooled operation double side cooled
(Kg)
Approximate weight Case style
200AB (A-PUK)
Outline Table
www.irf.com
ST230C.C Series
RthJ-hs Conduction
(The following table shows increment thermal resistence RthJ-hs when devices operate different conduction angles than
Conduction angle
180° 120°
Sinusoidal conduction
Single Side Double Side 0.015 0.018 0.024 0.035 0.060 0.017 0.019 0.024 0.035 0.060
Rectangular conduction
Single Side Double Side 0.011 0.019 0.026 0.036 0.060 0.011 0.019 0.026 0.037 0.061
Units
Conditions
max.
Ordering Information Table
Device Code
Thyristor Essential part number Converter grade Ceramic Voltage code: Code VRRM (See Voltage Rating Table) Case TO-200AB (A-PUK) Eyelet terminals (Gate Auxiliary Cathode Unsoldered Leads) Fast-on terminals (Gate Auxiliary Cathode Unsoldered Leads) Eyelet terminals (Gate Auxiliary Cathode Soldered Leads) Fast-on terminals (Gate Auxiliary Cathode Soldered Leads)
Critical dv/dt: None 500V/µsec (Standard selection) 1000V/µsec (Special selection)
www.irf.com
ST230C.C Series
Outline Table
ANODE GATE CREEPAGE DISTANCE: 7.62 (0.30) MIN. STRIKE DISTANCE: 7.12 (0.28) MIN. (0.75) DIA. MAX. (0.01) MIN.
13.7 14.4 (0.54 0.57) (0.01) MIN. (0.75) DIA. MAX. (1.50) MAX. GATE TERM. 1.47 (0.06) DIA. RECEPTACLE
Case Style TO-200AB (A-PUK)
HOLES 3.56 (0.14) 1.83 (0.07) MIN. DEEP (0.26) 4.75 (0.19)
dimensions millimeters (inches)
25°±
(1.65) MAX. (1.10)
Maximum Allowable Heatsink Temperature (°C)
Average On-state Current
Fig. Current Ratings Characteristics
Conduction Angle
Maximum Allowable Heatsink Temperature (°C)
ST230C.C Series (Single Side Cooled) thJ-hs (DC) 0.17
ST230C.C Series (Single Side Cooled) thJ-hs (DC) 0.17
Conduction Period
120° 180°
120° 180°
Average On-state Current
Fig. Current Ratings Characteristics
www.irf.com
ST230C.C Series
Maximum Allowable Heatsink Temperature (°C) Maximum Allowable Heatsink Temperature (°C) Average On-state Current
Fig. Current Ratings Characteristics
Conduction Angle
ST230C.C Series (Double Side Cooled) thJ-hs (DC) 0.08
ST230C.C Series (Double Side Cooled) thJ-hs (DC) 0.08
Conduction Period
120° 180°
120° 180°
Average On-state Current
Fig. Current Ratings Characteristics
Maximum Average On-st Power Loss
1100 1000 Average On-state Current
Fig. On-state Power Loss Characteristics
Conduction Angle
Maximum Average On-state Power Loss
1400 1200 1000
Conduction Period
180° 120°
Limit
180° 120° Limit
Average On-st Current
Fig. On-state Power Loss Characteristics
ST230C.C Series 125°C
ST230C.C Series 125°C
Peak Half Sine Wave On-state Current
5000 4500 4000 3500 3000
Rated Load Condition With Rated VRRM Applied Following Surge. Initial 125°C 0.0083 0.0100
Peak Half Sine Wave On-state Current
5500
6500 6000
Maximum Repetitive Surge Current Versus Pulse Train Duration. Control Conduction Maintained. 5500 Initial 125°C Voltage Reapplied 5000 Rated RRMReapplied 4500 4000 3500 3000 2500 ST230C.C Series Pulse Train Duration
Fig. Maximum Non-Repetitive Surge Current Single Double Side Cooled
2500 ST230C.C Series 2000
Number Equal Amplitude Half Cycle Current Pulses
2000 0.01
Fig. Maximum Non-Repetitive Surge Current Single Double Side Cooled
www.irf.com
ST230C.C Series
10000 Instantaneous On-state Current
25°C 125°C 1000
ST230C.C Series
Instantaneous On-state Voltage
Fig. On-state Voltage Drop Characteristics
Transient Thermal Impedance thJ-hs (K/W) Steady State Value thJ-hs 0.17 (Single Side Cooled) thJ-hs 0.08 (Double Side Cooled) Operation)
0.01 ST230C.C Series
0.001 0.001
0.01
Square Wave Pulse Duration
Fig. Thermal Impedance ZthJ-hs Characteristics
Instantaneous Gate Voltage Rectangular gate pulse Recommended load line rated di/dt 20V, 10ohms; tr<=1 Recommended load line <=30% rated di/dt 10V, 10ohms tr<=1
Tj=-40
10W, 20W, 40W, 60W,
0.66ms
Tj=25
Tj=125
0.01
Device: ST230C.C Series
Frequency Limited PG(AV)
Instantaneous Gate Current
Fig. Gate Characteristics
www.irf.com
Other recent searches
XEUR2350M - XEUR2350M XEUR2350M Datasheet
MAX2605 - MAX2605 MAX2605 Datasheet
MAX2606 - MAX2606 MAX2606 Datasheet
MAX2608 - MAX2608 MAX2608 Datasheet
MAX2609 - MAX2609 MAX2609 Datasheet
MAX2605-MAX2609 - MAX2605-MAX2609 MAX2605-MAX2609 Datasheet
HYMP532S64 - HYMP532S64 HYMP532S64 Datasheet
FTR-K1 - FTR-K1 FTR-K1 Datasheet
FTR-K3F - FTR-K3F FTR-K3F Datasheet
ENA1316 - ENA1316 ENA1316 Datasheet
FTD7011 - FTD7011 FTD7011 Datasheet
ADG1201 - ADG1201 ADG1201 Datasheet
ADG1202 - ADG1202 ADG1202 Datasheet
Privacy Policy | Disclaimer
© 2012 Datasheet Archive
