RI-07 SERIES Pico dry-reed switch hermetically sealed gas-filled glass

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

RI-07 SERIES Pico dry-reed switch hermetically sealed gas-filled glass

Datasheet Thumbnail

Top Searches for this datasheet

RI-07 Series
RI-07 SERIES Pico dry-reed switch hermetically sealed gas-filled glass envelope. Single-pole, single-throw (SPST) type, having normally open contacts, containing magnetically actuated reeds. switch double-ended type actuated electromagnet, permanent magnet combination both. device intended relays, sensors, pulse counters similar devices. RI-07 SERIES FEATURES Ideal general purpose reed relays sensors Contact layers: Gold/copper, sputtered plated ruthenium(can vary) Superior glass-to-metal seal blade alignment
Dimensions inches (mm) GENERAL DATA MODELS RI-07 Pref eformed AT-Customization Preformed Leads Besides standard models, customized products also supplied offering following options: Operate release ranges customer specification Cropped and/or preformed leads OILS characteristics measured using Philips Standard Coil. definitions Philips Standard Coil standard Coil, refer "Application Notes" Reed Switch Technical Application Information Section this catalog. between Standard Relationship between Philips Standard Coil Standard Standard Coil Operate value standard Coil 0.78 operate value Philips Standard Coil 1.02 Release value standard Coil 0.83 release value Philips Standard Coil 0.01
EXPECTANCY EXPECTANCY RELIABILITY life expectancy data given below valid coil energized 1.25 times published maximum operate value each type RI-07 series.
life criteria: Contact resistance after Release time (latching contact sticking). Loaded conditions (resistive load: operating requency: requency: Life expectancy: min. operations with failure rate less than 10-8 with confidence level 90%. life criteria: Contact resistance after Release time (latching contact sticking). Loaded conditions (resistive load: 12V; peak); operating frequency: Life expectancy: min. operations life criteria: Contact resistance after Release time (latching contact sticking). Switching different loads involves different life expectancy reliability data. Further information available request.
No-load conditions (operating frequency: Life expectancy: min. operations with failure rate less than 10-9 with confidence level 90%.
Rhopoint Components Fax: 1883 712938 Phone: 1883 717988 web: www.rhopointcomponents.com e-mail: sales@rhopointcomponents.com
RI-07 Series
Model Number Parameters Operating Characteristics
Operate Range Release Range Operate Time including bounce (typ.) Bounce Time (typ.) Release Time (max) Resonant Frequency (typ.) 7-19 3-16 0.25 0.05 6700 16-25 4-18 0.25 0.05 6700 20-36 6-19.5 0.45 0.05 6700 RI-07AAA RI-07AA RI-07A
Test Conditions
Units
Electrical Characteristics
Switched Power (max) Switched Voltage (max) Switched Voltage value (max) Switched Current (max) Switched Current value (max) Carry Current (max) Breakdown Voltage (min) Contact Resistance (initial max) Contact Resistance (initial typ.) Contact Capacitance (max) Insulation Resistance (min)
(energization) (energization) without test coil
1.75
1.75 0.25
MECHANICAL DATA Contact arrangement normally open; lead finish tinned; mass approximately 0.10 mounted position. SHOCK switches tested accordance with "IEC 68-2-27", test (peak acceleration half sinewave; duration ms). Such shock will cause open switch magnetic field present) close, switch kept closed coil open.
IBRATION VIBRATION switches tested accordance with "IEC 68-2-6", test (acceleration below cross-over frequency amplitude 0.75 frequency range 2000 duration minutes). Such vibration will cause open switch magnetic field present) close, switch kept closed coil open.
PERATING ORAGE EMPERATURE OPERATING STORAGE TEMPERATURE Operating ambient temperature; min: -55°C; max: +125°C. Storage temperature; min: -55°C; max: +125°C. Note: Temperature excursions 150°C permissible. more information contact your nearest Coto Technology sales office.
SOLDERING switch withstand soldering heat accordance with "IEC 68-2-20", test method solder bath ±10° ±0.5 Solderability tested accordance with "IEC 68-2-20" test method solder globule temperature 235°C; ageing hours steam. ELDING leads welded OUNTING leads should bent closer than glass-tometal seals. Stress seals should avoided. Care must taken prevent stray magnetic fields from influencing operating measuring conditions.
MECHANICAL STRENGTH robustness terminations tested accordance with "IEC 68-2-21", test (load
Rhopoint Components Fax: 1883 712938 Phone: 1883 717988 web: www.rhopointcomponents.com e-mail: sales@rhopointcomponents.com

RI-07 SERIES Pico dry-reed switch hermetically sealed gas-filled glass

Top Searches for this datasheet

Other recent searches