SERIES DOSTM)-BASED 1995 Document U10540EJ1V0UM00 (1st editi
|
|
|
Top Searches for this datasheet
PG-1500 CONTROLLER
SERIES DOSTM)-BASED
1995
Document U10540EJ1V0UM00 (1st edition) Date Published October 1995 Printed Japan
SUMMARY CONTENTS
CHAPTER CHAPTER CHAPTER CHAPTER CHAPTER CHAPTER CHAPTER APPENDIX
GENERAL CONNECTIONS START-UP CONTROL MODE AUTO MODE TERMINAL MODE ERROR MESSAGES EXAMPLE OPERATION CONTROL MODE
PC/AT, PC/XT, trademarks Corporation
information this document subject change without notice. part this document copied reproduced form means without prior written consent Corporation. Corporation assumes responsibility errors which appear this document. Corporation does assume liability infringement patents, copyrights other intellectual property rights third parties arising from device described herein other liability arising from such device. license, either express, implied otherwise, granted under patents, copyrights other intellectual property rights Corporation others.
INTRODUCTION
PG-1500 Controller software which enables more efficient PROM Programmer PG-1500. this software connected used host machine (PC/ATTM) remote control mode, more sophisticated functions used. PG-1500 Controller following features: Three modes, each having different functions, used: control mode, auto mode, terminal mode. Data written with extremely small number operations specifying appropriate options start-up auto mode). Files Intel HEX, Motorola expanded formats supported. connecting printer port (parallel interface conforming Centronics) host machine parallel interface PG-1500, data downloaded (from host machine internal memory PG1500) high speeds. functions PG-1500's remote control mode supported high-level functions.
This manual describes operations when PG-1500 Controller (Ver. 1.20 above) PROM Programmer PG-1500 (Ver. 1.80 above) used PC/AT.
[MEMO]
CONTENTS
CHAPTER GENERAL
Product Outline Functional Outline List PG1500C Commands
CHAPTER CONNECTIONS CHAPTER START-UP
Functions Options Operating Procedure Creating Configuration File Specifying Configuration File
CHAPTER CONTROL MODE
Screen Display 4.1.1 4.1.2 4.1.3 4.2.1 4.2.2 4.2.3 4.2.4 4.2.5 4.2.6 4.2.7 4.2.8 Configuration area Message area Execution area AUTO command command command LOAD command SAVE command command CONF command QUIT command
Commands Control Mode
Error Occurs Control Mode
CHAPTER AUTO MODE CHAPTER TERMINAL MODE
Commands 6.1.1 6.1.2 6.1.3 6.1.4 6.1.5 command command command command command
Commands 6.2.1 6.2.2 6.2.3 command command command
Commands Commands Commands Command Command
CHAPTER ERROR MESSAGES
APPENDIX EXAMPLE OPERATION CONTROL MODE
File PROM Auto Write
File Buffer Read PROM Buffer Read Buffer General-purpose PROM Write Buffer Silicon Signature Compatible Product Write Buffer Silicon Signature Non-Compatible Product Write Verification Contents Buffer PROM Buffer File Data Save
LIST FIGURES
Figure 4-10 4-11 4-12 4-13 4-14 4-15 4-16 4-17 4-18 4-19 4-20 4-21 4-22 4-23 4-24 4-25 4-26 4-27 4-28 4-29
Title Operating Configuration PG-1500 Example Connections between Host Machine PG-1500 Connections Serial (RS-232-C) Connections Parallel (Centronics) Appearance Switches PG-1500 Example Display Serial Setting Different Screen Image Control Mode Case "NORMAL" (NN) Case "16-Bit 2-Partition" (BE, Case "32-Bit 2-Partition" (WE, Case "32-Bit 4-Partition" (00, Start Screen Control Mode Inputting Number Sets (Screen Check (Screen File Loading (Screen Writing (Screen Write Message (Screen Replacement Request Message (Screen Command Selection Screen Command Execution Screen Command Execution Screen Command Execution Screen Command Execution Screen Command Execution Screen Command Selection Screen Command Execution Screen Command Execution Screen Command Execution Screen Command Parameter Input Screen Command Parameter Input Screen Command Execution Screen Command Execution Screen Execution Screen When CONV Changed Command Termination Screen Command Execution Screen Auto Mode Execution Screen Auto Mode Execution Screen
Page
LIST TABLES
Table 6-10 6-11 6-12 6-13 6-14 6-15
Title Host Machine PG1500C Modes Functions PG1500C Symbols Abbreviations Used This Manual Commands Used Control Mode Commands Used Terminal Mode PG1500C's Options Start-up Serial Standard Values PG1500C Contents Configuration File Default Values Specifying Directory Configuration File Commands Used Control Mode Parameters Default Values Commands Parameters Default Values Commands Commands Used Terminal Mode Input Functions during Command Error Abbreviated Formats Command Subcommands Command Their Functions Input Functions during Command Error Abbreviated Formats Command Input Functions during Command Error Abbreviated Formats Command Input Functions during Command Error Data That Input during Command Execution Their Functions Abbreviated Formats Command Keys That Input during Command Execution Their Functions Abbreviated Formats Command Abbreviated Formats Command Abbreviated Formats Command
Page
CHAPTER
GENERAL
CHAPTER
GENERAL
Product Outline
PG-1500 Controller (hereafter abbreviated PG1500C) software that controls PG-1500 PROM Programmer runs host machine. host machine PG-1500 connected with serial interface only (hereafter abbreviated serial I/F) with serial parallel interface (hereafter abbreviated parallel I/F). connect serial I/F, RS-232-C interface cable (straight cable) used. connect parallel I/F, parallel interface cable (printer cable) conforming Centronics. PG1500C runs under configuration shown Figure 1-1. Figure 1-1. Operating Configuration PG-1500
Serial Host machine (PC/AT) RS-232-C Straight cable PG-1500 Serial
Serial Host machine (PC/AT)
RS-232-C Straight cable
Serial
PG-1500 Printer cable
Printer
Parallel
host machine operating system under which PG1500C operates shown Table 1-1. Table 1-1. Host Machine PG1500C
Host Machine PC/AT
Execution File Name PG1500.EXE
Name Version (Ver. 3.30)
Caution When host machine PC/XTand PG1500C 5-inch version used, floppy disk drive floppy disk needed.
CHAPTER
GENERAL
Functional Outline
PG1500C following functions: "auto write function" which makes possible write ROMNote with extremely small number operations specifying appropriate options start-up (auto mode) provided. Files Intel HEX, Motorola expanded formats supported. Data downloaded high speeds (from host machine internal memory PG-1500) connecting parallel host machine parallel PG-1500. functions PG-1500 remote control mode supported (refer "1.3 List PG1500C Commands"). Note "Writing ROM" means writing including verification (the function command PG1500). Remark processing time differs depending version monitor PG-1500 processing performed. When file loaded, processing time differs depending size file transferred setting I/F. When data written, differs depending type device used range write address. transfer Mbits data, example, takes about minutes serial (with baud rate 9600 (baud)) used, about minutes parallel used. write data addresses Mbits, takes about minutes half
µPD27C1001 used, about minute half µPD27C1001A used.
CHAPTER
GENERAL
PG1500C three different modes. Table 1-2. Modes Functions PG1500C
Mode Control mode
Function Allows PG-1500 easily through selection operations listed screen. AUTO this mode same functions auto mode. Sets configuration, selects ROM, loads file, writes data (auto write function). Reinforces supports remote control mode PG-1500.
Auto mode
Terminal mode
auto mode terminal mode selected option specified start-up. this option omitted, control mode selected. specify option, refer "CHAPTER START-UP". Table lists meanings symbols abbreviations used throughout this manual. Table 1-3. Symbols Abbreviations Used This Manual
Symbol, Abbreviation buffer ROM_S_ADR ROM_E_ADR PG_S_ADR PG_E_ADR
Meaning PG-1500 internal memory start address address buffer start address buffer address Characters reverse video input Return input input omitted Either selected
Addresses input only 5-digit hexadecimal number. more digits cannot input.
CHAPTER
GENERAL
List PG1500C Commands
Table lists commands PG1500C used control mode. Table shows commands used terminal mode. Table 1-4. Commands Used Control Mode
Command Name A/AUTO
Function Automatically performs series operations (loading file, selecting ROM, writing ROM) write data accordance with data specified configuration file. Performs operations related such reading data from (same commands PG-1500). Changes, displays, initializes memory data PG-1500 (same commands PG-1500). Transfers file data PG-1500 (same commands PG-1500). Saves memory data PG-1500 file (same commands PG-1500).
R/ROM
M/MEM
L/LOAD
S/SAVE
O/OS C/CONF
Starts SHELL once returns control Changes configuration setting (configuration file also saved completion setting). Terminates PG1500C returns control (configuration file also saved).
Q/QUIT
CHAPTER
GENERAL
Table 1-5. Commands Used Terminal Mode
Command Name Reads data. Selects ROM.
Function
Compares data with PG-1500's memory data. Writes PG-1500's memory data ROM. Checks erasure status ROM. Changes PG-1500's memory data. Displays PG-1500's memory data. Initializes PG-1500's memory data. Transfers file Intel format PG-1500's memory (serial). Transfers file Motorola format PG-1500's memory (serial). Transfers file expanded format PG-1500's memory (serial). Saves PG-1500's memory data file Intel format. Saves PG-1500's memory data file Motorola format. Saves PG-1500's memory data file expanded format. Transfers file Intel format PG-1500's memory (parallel). Transfers file Motorola format PG-1500's memory (parallel). Transfers file expanded format PG-1500's memory (parallel). Command help Starts SHELL once returns control
CHAPTER
GENERAL
[MEMO]
CHAPTER
CONNECTIONS
CHAPTER
CONNECTIONS
host machine PG-1500 connected with serial (RS-232-C) only, with serial (RS-232C) parallel (Centronics), shown Figure 2-1. Figure 2-1. Example Connections between Host Machine PG-1500
Host machine PG-1500
printer connector
Printer cable RS-232-C connector RS-232-C cable Parallel connector Serial connector
CHAPTER
CONNECTIONS
Figure 2-2. Connections Serial (RS-232-C)
Host machine
PG-1500
Figure 2-3. Connections Parallel (Centronics)
Host machine
PG-1500
details serial parallel I/F, refer "PG-1500 User's Manual".
CHAPTER
START-UP
CHAPTER
START-UP
start PG1500C, input following command: A\PG1500 OPT] filename]
option
filename configuration file name option filename input order. Specifically, option filename input follows respective modes. Inputting A\PG1500 filename] filename] sets control mode (refer "CHAPTER 4"). sets auto mode (refer "CHAPTER 5"). sets terminal mode (refer "CHAPTER 6").
Inputting A\PG1500 Inputting A\PG1500
start PG1500C auto mode, sure specify configuration file name. character other than input option, error message displayed control returned
CHAPTER
START-UP
Functions Options
Table shows input formats functions options. Table 3-1. PG1500C's Options Start-up
Mode Control
Option specified
Configuration File Name Specified
Function Reads configuration fileNote specified filename, makes setting that matches configuration, waits command input. Sets configuration with default values configuration file, waits command input. Because name file loaded specified default value, sure specify filename when file loaded. Reads configuration file specified filenameNote makes setting that matches configuration, then executes automatic write (series operations including loading file, selecting ROM, writing data ROM). After operations have been completed, terminates PG1500C returns control Waits input filename. When filename input, performs same operation above. Displays error message returns control Operates intelligent terminal PG-1500. Displays error message returns control
specified
Auto
Specified
specified
Terminal
Other than above
Specified specified Specified/ specified
Notes configuration file file that specifies name file loaded, name used, split mode, file format, interface used load data. create configuration file details default values, refer "3.3 Creating Configuration File". file type omitted when configuration file name specified, ".PGC" assumed.
CHAPTER
START-UP
Operating Procedure
This section describes operating procedure PG-1500. Figure shows appearance switches PG-1500. Figure 3-1. Appearance Switches PG-1500
1500 PROMPROGRAMMER
Left side
Front panel
Right side
switches
switches COPY P-IN C-SUM CHANGE BLANK MODE S-IN INIT PROG CONT S-OUT MOVE VERIFY SELECT REMOTE SEARCH SET/START EDIT FUNC TION DEVI RESET
CHAPTER
START-UP
Start PG1500C follows: Connect host machine PG-1500 with serial (RS-232-C) only with parallel (Centronics) serial (RS-232-C), turn power. After host machine started insert floppy disk containing software PG1500C into current drive. mode serial using switches PG-1500 (for details switch operations, refer "PG-1500 User's Manual"). Press FUNCTION function mode. Press MODE serial interface setting mode. Move cursor using position parameter whose value setting changed, change parameter value setting using key. After setting parameters, press SET/START setting operation. When PG-1500 started values serial used last retained. starting PG1500C, serial standard values shown Table host machine. Make sure that these values PG-1500 match those PG1500C. Cautions When host machine PC/XT 1500C 5-inch version used, floppy disk drive floppy disk needed. change standard values serial PG1500C, operation <7>, which described below, must performed.
CHAPTER
START-UP
Table 3-2. Serial Standard Values PG1500C
Baud rate Parity XON/XOFF control Data length Stop
9600 (baud) bits bits
following keys PG-1500 respective modes. Press FUNCTION function mode. Press REMOTE remote control mode. display PG-1500, [REMOTE MODE] displayed. When prompt "A\" displayed, start PG1500C. Inputting A\PG1500 filename] Inputting A\PG1500 sets control mode (refer "CHAPTER 4"). sets auto mode (refer "CHAPTER 5"). sets terminal mode (refer "CHAPTER 6").
Inputting A\PG1500 filename]
Inputting causes title message displayed PG1500C started start PG1500C auto mode, sure specify configuration file name. character other than input option, error message displayed control returned Confirm that title message been displayed. Then press SET/START PG-1500 within seconds. setting PG-1500 matches setting serial host machine, synchronization established, specified mode set.
CHAPTER
START-UP
setting PG1500C different from that serial PG-1500, PG1500C synchronized with PG-1500, error message setting serial host machine displayed. Figure 3-2. Example Display Serial Setting Different
ERR40 Serial ready (Check cable, baud rate, data length, etc.) Select Q/QUIT retry. B/BAUD RATE P/PARITY X/XON C/DATA LENGTH S/STOP Q/QUIT 1200 2400 EVEN bits bits 4800 9600 19200 baud
change setting serial host machine, select parameter content whose value setting changed using keys keys, then press enter them. setting PG-1500 matches setting serial host machine, setting serial needs changed. Before selecting Q/QUIT press RESET PG-1500, perform operation <4>. Immediately after selecting Q/QUIT press SET/START PG-1500. setting PG-1500 matches setting serial host machine synchronization established, specified mode set.
CHAPTER
START-UP
Creating Configuration File
configuration file file that specifies name file loaded, name used, split mode, file format, interface used load data. specifying this file starting PG1500C, PG-1500 automatically accordance with contents file. However, cannot used terminal mode. configuration file created either following methods:
configuration area using CONF command PG1500C control mode save
configuration file when command terminated when QUIT command executed (refer "4.2.7 CONF command" "4.2.8 QUIT command").
Create file with editor.
file created with editor, describe "<Parameter> <Setting>" each parameter Table 3-4. parameters input order, distinction made between uppercase lowercase letters. space skipped. Each parameter must delimited space. Here example describing configuration file: Example FILE TEST.HEX UPD27256 CONV= LOAD When specifying AUTO command control mode auto mode, sure input name file loaded. used silicon signature non-compatible product, sure input corresponding generalpurpose PROM product name parameter name. silicon signature compatibility, refer "PG-1500 User's Manual". Cautions parameters created file missing, default values used their place (except file name name loaded) when file read. unnecessary parameter input, ignored. more values specified parameter, same parameter input more than once, error occurs.
CHAPTER
START-UP
Table 3-3. Contents Configuration File Default Values
Parameter FILE (Name loaded file)
Setting User-specified
Explanation Directory characters Primary name characters File type characters file type omitted, ".HEX" assumed. Input alphabet numeralNote Normal write bits, partitions bits, partitions bits, partitions Intel format Motorola format expanded format Serial specification Parallel specification
Default Value
(ROM name) CONV (split mode)
User-specified 16/2 32/2 32/4
Note NORMAL Normal write
(File format)
Intel format
LOAD (interface)
Serial specification
Notes Input name general-purpose PROM with replaced with "U". omit part number. Input name device other than general-purpose PROM with "µP" omitted. Example µPD27256 general-purpose PROM: Input "UPD27256". µPD75P054, which device other than general-purpose PROM: "D75P054". When silicon signature non-compatible product used with AUTO command control mode auto mode, "UPD27256" default value name input. Input
CHAPTER
START-UP
Specifying Configuration File
configuration file specified starting PG1500C, drive directory specified shown Table 3-4. Table 3-4. Specifying Directory Configuration File
drive directory specified
Specified file searched from directory specified drive read. specified file found, error message displayed control returned Specified file searched following sequence: Address configuration variable (variable name: PGC) Current directory current drive Address PG1500.EXE file found above locations, error message displayed control returned
drive directory specified
configuration file contains error, specified file found, error message displayed, control returned PG1500.EXE needs current drive, which case path where PG1500.EXE exists must specified path must modified start-up.
CHAPTER
START-UP
[MEMO]
CHAPTER
CONTROL MODE
CHAPTER
CONTROL MODE
control mode easily used carry variety operations from loading files writing them ROM, using extremely small number operations through selection operations listed screen. Files loaded either using serial (RS-232-C) only using serial (RS-232-C) parallel (Centronics) combination. operation control mode specified using configuration file user input. Input start-up A\PG1500 filename]
input during command execution, execution stopped PG1500C waits command inputNote. CTRL+C input, PG1500C terminated control returned Note Except during operation ROM.
CHAPTER
CONTROL MODE
Screen Display
screen shown Figure displayed when PG1500C started control mode with configuration file specified. contents specified configuration file displayed configuration area, indicating that PG1500C command input wait status control mode. Figure 4-1. Screen Image Control Mode
Configuration area Message area
***** CONTROL MODE ***** F/FILENAME R/ROM C/CONV TEST.HEX UPD27256 NORMAL
<MESSAGE> CONFIG FILE PG1500.PGC
H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
Execution area
A/AUTO
R/ROM
M/MEM
L/LOAD
S/SAVE
O/OS
C/CONF
Q/QUIT
Indicates command name
screen divided into three areas: configuration, message, execution areas. Each these areas described next.
CHAPTER
CONTROL MODE
4.1.1
Configuration area
configuration area upper left screen displays values read from configuration file default values starting PG1500C. values displayed this area changed CONF command. parameters different from those displayed configuration area when command other than command executed, values configuration area changed. configuration area parameters explained below. FILENAME (file name loaded) name file loaded displayed (even drive directory specified, only file name displayed drive name directory name displayed). drive directory specified when LOAD/SAVE command input, however, they displayed specified execution area parameters. This parameter default value. (ROM name) Displays name written. case "UPD27256", replaced with display entire name alphanumeric characters. Although default value supplemented starting name input when silicon signature non-compatible product used with AUTO command, "UPD27256" default value. silicon signature non-compatible name set, either leave blank name configuration area, corresponding general-purpose PROM name. SPLIT MODE (partition mode) This parameter displays address mapping method when written. There four methods specify partitioning: NORMAL, bits with partitions, bits with partitions, bits with partitions. default value "NORMAL". Figures through show address mapping method each partition specification.
CHAPTER
CONTROL MODE
Figure 4-2. Case "NORMAL" (NN) data file written
Figure 4-3. Case "16-Bit 2-Partition" (BE, Data bits divided into even addresses, then written 8-bit ROMs.
CHAPTER
CONTROL MODE
Figure 4-4. Case "32-Bit 2-Partition" (WE, Data bits divided into even addresses, then written 16-bit ROMs.
Even address (WE) File 16-bit File
address (WO) 16-bit
CHAPTER
CONTROL MODE
Figure 4-5. Case "32-Bit 4-Partition" (00, Data bits divided written four 8-bit ROMs follows:
File 8-bit File 8-bit
File 8-bit
File 8-bit
CHAPTER
CONTROL MODE
FORMAT (file format) following three file formats used: FORMAT Intel_HEX FORMAT Motorola_S FORMAT Tektronix_HEX default value "Intel_HEX". INTERFACE There types INTERFACE shown below. INTERFACE SERIAL INTERFACE PARALLEL default value "SERIAL". 4.1.2 Message area Specifies serial interface. Specifies parallel interface. Specifies Intel format. Specifies Motorola format. Specifies expanded format.
message area displays name configuration file error messages. data input user this area. 4.1.3 Execution area
execution area displays messages indicating process operation, messages requesting input, data sent from PG-1500.
CHAPTER
CONTROL MODE
Commands Control Mode
When PG1500C started control mode with configuration file specified, configuration specified file set. configuration file specified, default values read, PG1500C waits command input. Figure 4-6. Start Screen Control Mode
***** CONTROL MODE ***** F/FILENAME R/ROM
<MESSAGE> CONFIG FILE Please select command.
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
A/AUTO
R/ROM
M/MEM
L/LOAD
S/SAVE
O/OS
C/CONF
Q/QUIT
Table shows commands control mode.
CHAPTER
CONTROL MODE
Table 4-1. Commands Used Control Mode
Command A/AUTO
Function Automatically performs series operations (loading file, selecting ROM, writing ROM) write data accordance with specified configuration file data. Performs operations related such reading data from (same commands PG-1500). Changes, displays, initializes memory data PG-1500 (same commands PG-1500). Transfers file data PG-1500 (same commands PG-1500). Saves memory data PG-1500 file (same commands PG-1500). Starts SHELL once returns control Changes configuration setting (configuration file also saved completion setting). Terminates PG1500C returns control (configuration file also saved).
R/ROM
M/MEM
L/LOAD
S/SAVE
O/OS C/CONF
Q/QUIT
Each command always displayed bottom screen during execution control mode. Each command executed following methods: keys move position command displayed reverse video then press key. Input alphabetic character leftmost position command.
CHAPTER
CONTROL MODE
4.2.1 area.
AUTO command
command automatically writes data accordance with setting displayed configuration When using command, configuration area reading configuration file starting PG1500C, using CONF command. sure input FILENAME. used silicon signature non-compatible product, product name general-purpose which corresponds name, must set. name specified, µPD27256 assumed. When command input, operations performed automatically following sequence: Request inputting number sets (screen check (screen File loading (screen Writing (screen Write message (screen When data written more ROMs number setsNote more, S/SPLIT MODE other than "NORMAL"), replacement request message (screen performed, operations repeated until data have been completely written. When operations have been completed, PG1500C enters command input wait status. Note number sets specifies number chip sets created same write method. Data written even addresses then addresses ROMs split into partitions. split into four partitions, they written same contents written number sets once. Example: write sets 16-bit, partitions Even addresses Even addresses addresses addresses
CHAPTER
CONTROL MODE
Figures through 4-12 show execution screens (screens through command. Figure 4-7. Inputting Number Sets (Screen
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27256
<MESSAGE> CONFIG FILE PG1500.PGC
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
Number
A/AUTO
R/ROM
M/MEM
L/LOAD
S/SAVE
O/OS
C/CONF
Q/QUIT
default value number sets, displayed shown above. only input, set. desired number sets, input desired number then press key.
CHAPTER
CONTROL MODE
Figure 4-8. Check (Screen
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27256
<MESSAGE> CONFIG FILE PG1500.PGC
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
Number Check: UPD27256
A/AUTO
R/ROM
M/MEM
L/LOAD
S/SAVE
O/OS
C/CONF
Q/QUIT
check select automatically. First, silicon signature read, read data compared against name displayed configuration area. they match, name displayed configuration area, comparison terminated. names match, error message displayed. name displayed configuration area general-purpose PROM device other than generalpurpose PROM used, silicon signature cannot read. former case, name displayed configuration area selected device other than general-purpose PROM displayed name displayed configuration area, "D27256" automatically selected. After check been completed, file loading started.
CHAPTER
CONTROL MODE
Figure 4-9. File Loading (Screen
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27256
<MESSAGE> CONFIG FILE PG1500.PGC
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
Number Check: UPD27256 File Loading
A/AUTO
R/ROM
M/MEM
L/LOAD
S/SAVE
O/OS
C/CONF
Q/QUIT
While file loaded, message "File Loading" blinks. Blinking stops when file been completely loaded. error occurs during loading, error message displayed message area (refer "CHAPTER ERROR MESSAGES"), PG1500C enters command input wait status. When file loaded, buffer PG-1500 (processing command PG-1500) also initialized.
CHAPTER
CONTROL MODE
Figure 4-10. Writing (Screen
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27256
<MESSAGE> CONFIG FILE PG1500.PGC
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
Number Check: UPD27256 File Loading Writing (NN)
A/AUTO
R/ROM
M/MEM
L/LOAD
S/SAVE
O/OS
C/CONF
Q/QUIT
Data written ROM. SPLIT MODE "NORMAL", only message "Writing (NN)" displayed. "16/2", message "Writing (even address))" displayed. other words, address mapping method displayed enclosed (refer "CONV" "4.1.1 Configuration area"). While data written ROM, message "Writing" blinks. display returns normal when writing been completed.
CHAPTER
CONTROL MODE
Figure 4-11. Write Message (Screen
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27256
<MESSAGE> CONFIG FILE PG1500.PGC
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
Number Check: UPD27256 File Loading Writing (NN) erase Now, data writing! Data complete Check sum: 78D6 Write completed
A/AUTO
R/ROM
M/MEM
L/LOAD
S/SAVE
O/OS
C/CONF
Q/QUIT
above message displayed when data been completely written ROM.
CHAPTER
CONTROL MODE
Figure 4-12. Replacement Request Message (Screen
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27256
<MESSAGE> CONFIG FILE PG1500.PGC
S/SPLIT MODE bit/2 H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
Number Check: UPD27256 File Loading Writing (even address))
erase Now, data writing! Data complete Check sum: C63B
Write completed. Next (odd address). Change ROM, push key. A/AUTO R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
number sets more, SPLIT MODE other than "NORMAL", message prompting change displayed.
CHAPTER
CONTROL MODE
4.2.2
command
command corresponds commands "RR", "RS", "RV", "RW", "RZ" terminal mode (for details execution contents, refer "CHAPTER TERMINAL MODE" "PG-1500 User's Manual"). Select commands following procedure while PG1500C command input wait status (refer Figure 4-6). Move position display reverse video R/ROM using followed input key. input character leftmost position command, "R". Then Command Selection Screen" shown Figure 4-13 will displayed. Display R/DATA READ Z/ZERO CHECK (BLANK CHECK) reverse video using followed input key. input character leftmost position command, "Z". Then execution screen specified command will displayed (refer Figures 4-14 through 4-18). Remark When inputting alphabetic character leftmost position command, above performed after another without confirming command selection screen. example, execute command, input "RR".
CHAPTER
CONTROL MODE
Table lists parameters default values commands. Table 4-2. Parameters Default Values Commands
Command start address address
Parameter 00000
Default Value
address selected 00000 Value displayed configuration area None
buffer start address CONV Select Reads silicon signature Reads silicon signature during PROM operation Selects according code number start address address buffer start address CONV start address address buffer start address CONV None
00000 address selected 00000 Value displayed configuration area 00000 address selected 00000 Value displayed configuration area None
Remark
Input address 5-digit hexadecimal number. address digits less, input higher digit(s). address digits longer must input.
CHAPTER
CONTROL MODE
Figure 4-13. Command Selection Screen
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27256
<MESSAGE> CONFIG FILE PG1500.PGC
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
R/DATA READ S/SELECT V/VERIFY (MASTER PG_BUFFER) W/WRITE (PG_BUFFER ROM) Z/ZERO CHECK (BLANK CHECK)
A/AUTO
R/ROM
M/MEM
L/LOAD
S/SAVE
O/OS
C/CONF
Q/QUIT
CHAPTER
CONTROL MODE
Figure 4-14. Command Execution Screen
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27256
<MESSAGE> CONFIG FILE PG1500.PGC
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
RR/DATA READ START ADDRESS ADDRESS 00000 07FFF
PG_BUFFER START ADDRESS 00000
SPLIT MODE
START
A/AUTO
R/ROM
M/MEM
L/LOAD
S/SAVE
O/OS
C/CONF
Q/QUIT
default value each parameter displayed first (refer "Table Parameters Default Values Commands"). input value parameter, first select parameter using keys. Then input key. value specified parameter changed. only input, currently value parameter left unchanged. value input position display reverse video moved followed input key, specified value (for details CONV, refer Figures through 4-5). When "START" selected, execution command started message "Now, data reading!" blinks. When execution been completed, message "Data complete" checksum displayed, PG1500C enters command input wait status.
CHAPTER
CONTROL MODE
Figure 4-15. Command Execution Screen
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27256
<MESSAGE> CONFIG FILE PG1500.PGC
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
RS/SELECT R/SIGNATURE READ A/SIGNATURE AUTO READ C/CODE SELECT
A/AUTO
R/ROM
M/MEM
L/LOAD
S/SAVE
O/OS
C/CONF
Q/QUIT
Move line displayed reverse video using then input key, input alphabetic character displayed leftmost position. Then execution will started. Cautions1. selected verified against name displayed configuration area. 2.-"R/SIGNATURE READ" "A/SIGNATURE AUTO READ" executed only with silicon signature-compatible products. silicon signature non-compatible products, select "C/CODE SELECT".
CHAPTER
CONTROL MODE
Figure 4-16. Command Execution Screen
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27256
<MESSAGE> CONFIG FILE PG1500.PGC
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
RV/VERIFY (MASTER PG_BUFFER) START ADDRESS ADDRESS 00000 07FFF
PG_BUFFER START ADDRESS 00000 SPLIT MODE START
A/AUTO
R/ROM
M/MEM
L/LOAD
S/SAVE
O/OS
C/CONF
Q/QUIT
default value each parameter displayed first (refer "Table Parameters Default Values Commands"). input value parameter, first select parameter using keys followed input key. value specified parameter changed. only input, currently value parameter left unchanged. value input position display reverse video moved followed input key, specified value set. When "START" selected, execution command started message "Now, data reading!" blinks. When execution been completed, message "Data complete" checksum displayed, PG1500C enters command input wait status.
CHAPTER
CONTROL MODE
Figure 4-17. Command Execution Screen
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27256
<MESSAGE> CONFIG FILE PG1500.PGC
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
RW/WRITE (PG_BUFFER ROM) START ADDRESS ADDRESS 00000 07FFF
PG_BUFFER START ADDRESS 00000 SPLIT MODE START
A/AUTO
R/ROM
M/MEM
L/LOAD
S/SAVE
O/OS
C/CONF
Q/QUIT
default value each parameter displayed first (refer "Table Parameters Default Values Commands"). input value parameter, first select parameter using keys. Then input key. value specified parameter changed. only input, currently value parameter left unchanged. value input position display reverse video moved followed input key, specified value set. When "START" selected, execution command started message "Now, data writing!" blinks. When execution been completed, message "Data complete" checksum displayed, PG1500C enters command input wait status.
CHAPTER
CONTROL MODE
Figure 4-18. Command Execution Screen
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27256
<MESSAGE> CONFIG FILE PG1500.PGC
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
RZ/ZERO CHECK (BLANK CHECK)
A/AUTO
R/ROM
M/MEM
L/LOAD
S/SAVE
O/OS
C/CONF
Q/QUIT
Execution command started immediately because necessary specify parameters this command. When execution been completed, message "ROM erase OK!" displayed PG1500C enters command input wait status.
CHAPTER
CONTROL MODE
4.2.3
Memory command
command corresponds "MC", "MD", "MF" commands terminal mode (for details execution contents, refer "CHAPTER TERMINAL MODE" "PG-1500 User's Manual"). However, control mode, command terminal mode called command. Select commands following procedure from command input wait status (Figure 4-6). Move position display reverse video M/MEM using followed input key. input character leftmost position command, "M". Command Selection Screen" shown Figure 4-19 will displayed. Move position display reverse video C/CHANGE PG_BUFFER DATA I/INITIALIZE PG_BUFFER using followed input key. input character leftmost position command, "I". execution screen specified command will displayed (refer Figures 4-20 through 4-22). Remark When inputting alphabetic character leftmost position command, above performed after another without confirming command selection screen. example, execute command, input "MC". Table lists parameters default values commands. Table 4-3. Parameters Default Values Commands
Command
Parameter buffer start address buffer start address buffer address 00000 00000 7FFFF 00000 7FFFF FFNote
Default Value
buffer start address buffer address Initialization data
Note command been executed before executing command, initialization data selected will set. command been executed, name configuration area, initialization data that will (the setting made command takes precedence over setting configuration area). Remark Input address 5-digit hexadecimal number. address digits less, input higher digit(s). address digits longer must input.
CHAPTER
CONTROL MODE
Figure 4-19. Command Selection Screen
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27256
<MESSAGE> CONFIG FILE PG1500.PGC
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
C/CHANGE PG_BUFFER DATA D/DISPLAY PG_BUFFER DATA F/INITIALIZE PG_BUFFER
A/AUTO
R/ROM
M/MEM
L/LOAD
S/SAVE
O/OS
C/CONF
Q/QUIT
CHAPTER
CONTROL MODE
Figure 4-20. Command Execution Screen
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27256
<MESSAGE> CONFIG FILE PG1500.PGC
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
MC/CHANGE PG_BUFFER DATA PG_BUFFER START ADDRESS START 00000
A/AUTO
R/ROM
M/MEM
L/LOAD
S/SAVE
O/OS
C/CONF
Q/QUIT
default value parameter, "00000", first displayed (refer "Table Parameters Default Values Commands"). change start address buffer, first display BUFFER START ADDRESS" reverse video using key. Next input key. value parameter changed. only input this time, currently value parameter left unchanged. value input followed input key, parameter changed specified value. When "START" selected, execution command started. error occurs, error message displayed message area. 2-digit hexadecimal number input, contents address currently displayed changed, next address then displayed. terminate command, input key. After command been terminated, PG1500C enters command input wait status.
CHAPTER
CONTROL MODE
Figure 4-21. Command Execution Screen
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27256
<MESSAGE> CONFIG FILE PG1500.PGC
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
MD/DISPLAY PG_BUFFER DATA PG_BUFFER START ADDRESS PG_BUFFER ADDRESS START 00000 7FFFF
A/AUTO
R/ROM
M/MEM
L/LOAD
S/SAVE
O/OS
C/CONF
Q/QUIT
default value parameter first displayed (refer "Table Parameters Default Values Commands"). change value parameter, first select parameter using keys followed input key. only input this time, currently value parameter left unchanged. value input followed input key, parameter changed specified value. When "START" selected, execution command started. error occurs, error message displayed message area. CTRL+C input during execution, control returned abort command, input key. When execution been completed, PG1500C enters command input wait status.
CHAPTER
CONTROL MODE
Figure 4-22. Command Execution Screen
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27256
<MESSAGE> CONFIG FILE PG1500.PGC
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
MF/INITIALIZE PG_BUFFER PG_BUFFER START ADDRESS PG_BUFFER ADDRESS INITIAL DATA START 00000 7FFFF
A/AUTO
R/ROM
M/MEM
L/LOAD
S/SAVE
O/OS
C/CONF
Q/QUIT
default value parameter first displayed (refer "Table Parameters Default Values Commands"). change value parameter, first select parameter using keys followed input key. only input this time, currently value parameter left unchanged. value input followed input key, parameter changed specified value. "INITIAL DATA", following value:
µPD75P54, 75P56, 75P64, 75P66: initialization data "00"
devices other than above initialization data "FF"
When "START" selected, execution started. When execution been completed, PG1500C enters command input wait status.
CHAPTER
CONTROL MODE
4.2.4
LOAD command
command corresponds "LI", "LM" "LT" commands terminal mode INTERFACE serial, "PI", "PM", "PT" INTERFACE parallel (for details execution contents, refer "CHAPTER TERMINAL MODE"). When command input while PG1500C command input wait status (refer Figure 4-6), PG1500C enters parameter input wait status (refer Figure 4-23). command input following ways: Move position display reverse video command display area (execution area) using key, L/LOAD then press key. Input "L".
CHAPTER
CONTROL MODE
Figure 4-23. Command Parameter Input Screen
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27256
<MESSAGE> CONFIG FILE PG1500.PGC
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
FILENAME B:\ABCD\EFG\TEST.HEX FORMAT Intel_HEX INTERFACE START SERIAL Motorola_S PARALLEL Tektronix_HEX
A/AUTO
R/ROM
M/MEM
L/LOAD
S/SAVE
O/OS
C/CONF
Q/QUIT
values parameters displayed configuration area first displayed execution area. input names, such drive name directory name, displayed name file loaded. change value parameter, first select parameter using key, then input key. only input this time, current value parameter left unchanged. file name input, setting "HEX FORMAT" "INTERFACE" changed using followed input key, file name selected file format interface type set. file name input, sure input file name before executing this command. When "START" selected, execution command started. When execution been completed, message "Load complete" displayed, PG1500C enters command input wait status.
CHAPTER
CONTROL MODE
4.2.5
SAVE command
command corresponds "SI", "SM", "ST" commands terminal mode (for details execution contents, refer "CHAPTER TERMINAL MODE" "PG-1500 User's Manual"). When command input with PG1500C command input wait status (refer Figure 4-6), PG1500C enters parameter input wait status (refer Figure 4-24). command input following ways: Move position display reverse video command display area (execution area) using key, S/SAVE then press key. Input "S".
CHAPTER
CONTROL MODE
Figure 4-24. Command Parameter Input Screen
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27256
<MESSAGE> CONFIG FILE PG1500.PGC
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
FILENAME B:\ABCD\EFG\TEST.HEX FORMAT PG_BUFFER ADDRESS START Intel_HEX 7FFFF Motorola_S Tektronix_HEX
PG_BUFFER START ADDRESS 00000
A/AUTO
R/ROM
M/MEM
L/LOAD
S/SAVE
O/OS
C/CONF
Q/QUIT
values parameters displayed configuration area first displayed execution area. "00000" displayed PG_BUFFER START ADDRESS "7FFFF" PG_BUFFER ADDRESS. change value parameter, first select parameter using key, then input key. only input this time, current value parameter left unchanged. value alphabetic character specified followed input key, value parameter changed specified value. When "START" selected, execution command started. name file saved specified this time, data sent from PG-1500 displayed execution area. When execution been completed, message "Save complete" displayed, PG1500C enters command input wait status.
CHAPTER
CONTROL MODE
4.2.6
command Figure 4-25. Command Execution Screen
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27256
<MESSAGE> CONFIG FILE PG1500.PGC
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
A/AUTO
R/ROM
M/MEM
L/LOAD
S/SAVE
O/OS
C/CONF
Q/QUIT
When command input with PG1500C command input wait status (refer Figure 4-6), control returned command input following ways: Move position display reverse video command display area (execution area) using O/OS then input key. Input "O". return control mode again, input EXIT
CHAPTER
CONTROL MODE
4.2.7
CONF command
When command input with PG1500C command input wait status (refer Figure 4-6), screen shown Figure 4-26 displayed. command input following ways: Move position display reverse video command display area (execution area) using C/CONF then press key. Input "C".
CHAPTER
CONTROL MODE
Figure 4-26. Command Execution Screen
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27256
<MESSAGE> CONFIG FILE PG1500.PGC
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
A/AUTO
R/ROM
M/MEM
L/LOAD
S/SAVE
O/OS
C/CONF
Q/QUIT
When position display reverse video configuration area moved using then input, when alphabetic character leftmost position parameter selected input, value selected parameter changed. "F/FILENAME" "R/ROM" selected, file name name input from keyboard (for input format, refer "3.3 Creating Configuration File"). "S/SPLIT MODE", "H/HEX FORMAT", "I/INTERFACE" specified, menu specified parameter displayed. Move position display reverse video using input key. setting been changed, configuration file saved when CONF command been terminated.
CHAPTER
CONTROL MODE
example, Figure 4-27 shows execution screen when "S/SPLIT MODE" selected. Figure 4-27. Execution Screen When SPLIT MODE Changed
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27256
<MESSAGE> CONFIG FILE PG1500.PGC
HELP
S/SPLIT MODE H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
NORMAL
16bit/2
32bit/2
32bit/4
A/AUTO
R/ROM
M/MEM
L/LOAD
S/SAVE
O/OS
C/CONF
Q/QUIT
Move position display reverse video execution area using select desired parameter, press key.
CHAPTER
CONTROL MODE
When "H/HEX FORMAT" selected same manner when "S/SPLIT MODE" selected, following message displayed: Intel_HEX Motorola_S Tektronix_HEX
Likewise, when "I/INTERFACE" selected, following message displayed: SERIAL PARALLEL
HELP pressed while SPLIT MODE selected, figures shown "<3> SPLIT MODE 4.1.1 Configuration area" displayed execution area. address mapping method SPLIT MODE displayed reverse video displayed this time. pressed again, screen returns that shown Figure 4-27.
CHAPTER
CONTROL MODE
Figure 4-28 shows screen terminate command. Figure 4-28. Command Termination Screen
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27256
<MESSAGE>
INSERT
CONFIG FILE PG1500.PGC
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
Save configuration file? S/SAVE E/END Input configuration file name. FILENAME A:\XYZ\PG1500.PGC
A/AUTO
R/ROM
M/MEM
L/LOAD
S/SAVE
O/OS
C/CONF
Q/QUIT
Press while E/END displayed reverse video. configuration parameter been changed, message inquiring whether change also saved displayed execution area. parameter been changed, PG1500C returns command input wait status (refer Figure 4-6). save setting, message prompting input configuration file name displayed. only input this time, file currently displayed overwritten. message requesting input file name displayed execution area. input, configuration file saved. When configuration file been saved correctly, name saved file displayed position configuration file message area. When CONF command been terminated, PG1500C enters command input wait status.
CHAPTER
CONTROL MODE
4.2.8
QUIT command
When command input with PG1500C command input wait status (refer Figure 4-6), screen shown Figure 4-29 displayed. command input following ways: Move position display reverse video command display area (execution area) using Q/QUIT press key. Input "Q".
Error Occurs Control Mode
error occurs control mode, error message displayed (refer "CHAPTER ERROR MESSAGES"). error message consists error number message displayed message area. addition, remedies also displayed execution area. error message erased inputting command accordance with messages displayed execution area.
CHAPTER
CONTROL MODE
Figure 4-29. Command Execution Screen
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27256
<MESSAGE>
INSERT
CONFIG FILE PG1500.PGC
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
Save configuration file? S/SAVE E/END Input configuration file name. FILENAME \XYZ\PG1500.PGC
A/AUTO
R/ROM
M/MEM
L/LOAD
S/SAVE
O/OS
C/CONF
Q/QUIT
When command input, PG1500C terminated, control returned contents configuration file have been changed been saved, however, above screen displayed. "S/SAVE END" selected, message requesting input configuration file name displayed. "E/END" selected, PG1500C terminated without saving contents configuration file.
CHAPTER
CONTROL MODE
[MEMO]
CHAPTER
AUTO MODE
CHAPTER
AUTO MODE
auto mode only when option that sets mode been input configuration file been specified starting PG1500C. However, some parameters configuration file configuration file contains error, screen auto mode displayed, message requesting input configuration file name displayed. auto mode, configuration file specified filename read setting made accordance with specified configuration. Subsequently, check, file loading, writing data successively performed. When been written, control automatically returned When file loaded, buffer also initialized (processing command PG-1500). error found when control been returned error message displayed (refer "CHAPTER ERROR MESSAGES"). Input start-up A\PG1500 filename]
input during auto mode, execution aborted control returned OSNote. When CTRL+C input, PG1500C terminated, control returned Note Except during operation
CHAPTER
AUTO MODE
Figure 5-1. Auto Mode Execution Screen
***** AUTO MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C2001
<Message> CONFIG FILE PG1500.PGC
S/SPLIT MODE 16bit/2 H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
Check:
CHAPTER
AUTO MODE
When been completely written, messages shown Figure displayed (except NORMAL mode). Figure 5-2. Auto Mode Execution Screen
***** AUTO MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C2001
<Message> CONFIG FILE PG1500.PGC
S/SPLIT MODE 16bit/2 H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
Check: UPD27C2001 File Loading Writing (even address)) erase Now, data writing! Data complete Check sum: 78D6 Write completed. Next (odd address). Change ROM, push key.
CONV "NORMAL", only message "Writing (NN)" displayed. bit/2", message "Writing (even address)) displayed. other words, address mapping method displayed enclosed (refer "<3> SPLIT MODE" "4.1.1 Configuration area"). Data written even addresses then addresses number partitions number partitions data written that order.
CHAPTER
AUTO MODE
[MEMO]
CHAPTER
TERMINAL MODE
CHAPTER
TERMINAL MODE
terminal mode, commands listed Table input along with parameters such addresses order manipulate PG-1500. When terminal mode set, following screen displayed:
***** TERMINAL MODE *****
prompt, indicating that PG1500C command input wait status terminal mode. terminal mode, commands listed Table used (for error messages, refer "CHAPTER ERROR MESSAGES"). Input start-up A\PG1500
input during command execution, command aborted, PG1500C enters command input wait statusNote. When CTRL+C input, PG1500C terminated, control returned Note Except operation
CHAPTER
TERMINAL MODE
Table 6-1. Commands Used Terminal Mode
Command Name Reads data. Selects ROM.
Function
Compares data with PG-1500's memory data. Writes PG-1500's memory data ROM. Checks erasure status ROM. Changes PG-1500's memory data. Displays PG-1500's memory data. Initializes PG-1500's memory data. Transfers file Intel format PG-1500's memory (serial). Transfers file Motorola format PG-1500's memory (serial). Transfers file expanded format PG-1500's memory (serial). Saves PG-1500's memory data file Intel format. Saves PG-1500's memory data file Motorola format. Saves PG-1500's memory data file expanded format. Transfers file Intel format PG-1500's memory (parallel). Transfers file Motorola format PG-1500's memory (parallel). Transfers file expanded format PG-1500's memory (parallel). Command help Starts SHELL once returns control
CHAPTER
TERMINAL MODE
meanings symbols used command description follows:
Symbol ROM_S_ADR ROM_E_ADR PG_S_ADR PG_E_ADR SPLIT PROM start address PROM address PG-1500 buffer start address PG-1500 buffer address
Meaning
Specifies address partition type follows: NORMAL address partition) 16-bit data, partitions, even addresses 16-bit data, partitions, addresses 32-bit data, partitions, even addresses 32-bit data, partitions, addresses 32-bit data, partitions, block 32-bit data, partitions, block 32-bit data, partitions, block 32-bit data, partitions, block
Return input Input from keyboard (underline)
Remarks Input address 5-digit hexadecimal number. more digits input, error occurs. symbol other than those specified above input specify address partitioning, error occurs.
CHAPTER
TERMINAL MODE
Commands
Five commands available: "RR", "RS", "RV", "RW", "RZ". function, input format, execution example, abbreviated format each command described below. 6.1.1 command Reads data specified range from inserted into socket internal memory PG-1500. [Input format] PG\RR [ROM_S_ADR] [,ROM_E_ADR] [,PG_S_ADR] [,SPLIT]
[Function]
ROM_S_ADR Input (PROM start address). ROM_E_ADR Input (PROM address). PG_S_ADR SPLIT [Execution example] case Input (PG-1500 buffer start address). Select (address partition mode). ROM_S_ADR 00000 ROM_E_ADR 0FFFF PG_S_ADR SPLIT 00000
During normal execution
PG\RR 0,FFFF,0,BE Now, data reading Data complete Check 7E40
CHAPTER
TERMINAL MODE
error occurs during verification
PG\RR 0,FFFF,0,BE Now, data reading ERR20 Data completed 00000 data data
Continue Yes/N: No)?
message [Continue (Y:Yes/N:No)?] displayed during execution, input response. Table shows operation performed when input. Table 6-2. Input Functions during Command Error
Input Others
Function Executes verification again starting from address next that displayed Aborts verification Displays [Continue] message again
[Abbreviated format]
terminal mode, commands input abbreviated format. Table shows variations abbreviations.
CHAPTER
TERMINAL MODE
Table 6-3. Abbreviated Formats Command
Input Format ROM_S_ADR,ROM_E_ADR,PG_S_ADR, ROM_S_ADR,ROM_E_ADR,PG_S_ADR ROM_S_ADR,ROM_E_ADR,,SPLIT ROM_S_ADR,ROM_E_ADR,, ROM_S_ADR,ROM_E_ADR ROM_S_ADR,,PG_S_ADR,SPLIT ROM_S_ADR,,PG_S_ADR, ROM_S_ADR,,PG_S_ADR ROM_S_ADR,,,SPLIT ROM_S_ADR,,, ROM_S_ADR,, ROM_S_ADR, ROM_S_ADR ,ROM_E_ADR,PG_S_ADR,SPLIT ,ROM_E_ADR,PG_S_ADR, ,ROM_E_ADR,PG_S_ADR ,ROM_E_ADR,,SPLIT ,ROM_E_ADR,, ,ROM_E_ADR ,,PG_S_ADR,SPLIT ,,PG_S_ADR, ,,PG_S_ADR ,,,SPLIT
ROM_S_ADR Address input Address input Address input Address input Address input Address input Address input Address input Address input Address input Address input Address input Address input Address input
ROM_E_ADR Address input Address input Address input Address input Address input Address input Address input Address input Address input Address input Address input Address input Note ROM_E_ADR
PG_S_ADR Address input Address input Address input Address input Address input Address input Address input Address input Address input Address input Address input Address input
SPLIT Input Input Input Input Input Input Input Input
Remark
Note Note Note Note Note Note Note Note
Notes ROM_S_ADR ROM_E_ADR, error occurs. Input address selected when selected SELECT. When selected, input address silicon signature data previously read. When selected, input address read silicon signature data.
CHAPTER
TERMINAL MODE
6.1.2
command Selects inserted device (SELECT). device selected specified subcommands Table 6-4. Subcommands Command Their Functions
[Function]
Subcommand (CODE) (READ) (AUTO) Others omission
Function Inputs code number during command execution selects device.
Reads silicon signature during command execution selects device.
Reads silicon signature during execution command, selects device. Error
Caution subcommand used with general-purpose PROMs devices whose writing conditions same those general-purpose PROMs. Subcommands used only with silicon signature compatible products.
CHAPTER
TERMINAL MODE
[Input format]
PG\RS PG\RS PG\RS Subcommand
Input above. character other than input subcommand, error occurs.
PG\RS ERR16 Command syntax error
[Execution example
PG\RS With board During normal execution
PG\RS SELECT 1004=uPD27256 10C4=uPD27256A 1025=uPD27C512 (VPP=21V) 10A4=uPD27C256 (VPP=21V) (VPP=12.5V) (F/N) (VPP=12.5V) (F/N) 1064=uPD27C256A (VPP=12.5V) (F/N) 1086=uPD27C1000 (VPP=12.5V) 1046=uPD27C1001 (VPP=12.5V) 1026=uPD27C1024 (VPP=12.5V) 10C7=uPD27C2001 (VPP=12.5V) (P/N) 10A8=uPD27C4096 (VPP=12.5V)
1016=uPD27C1000A (VPP=12.5V) (P/N) 10D6=uPD27C1001A (VPP=12.5V) (P/N) 10B6=uPD27C1024A (VPP=12.5V) (P/N) 10C8=uPD27C4001 (VPP=12.5V) Please input code No.=1004
CHAPTER
TERMINAL MODE
error occurs
PG\RS SELECT 1004=uPD27256 10C4=uPD27256A 1025=uPD27C512 (VPP=21V) 10A4=uPD27C256 (VPP=21V) (VPP=12.5V) (F/N) (VPP=12.5V) (F/N) 1064=uPD27C256A (VPP=12.5V) (F/N) 1086=uPD27C1000 (VPP=12.5V) 1046=uPD27C1001 (VPP=12.5V) 1026=uPD27C1024 (VPP=12.5V) 10C7=uPD27C2001 (VPP=12.5V) (P/N) 10A8=uPD27C4096 (VPP=12.5V)
1016=uPD27C1000A (VPP=12.5V) (P/N) 10D6=uPD27C1001A (VPP=12.5V) (P/N) 10B6=uPD27C1024A (VPP=12.5V) (P/N) 10C8=uPD27C4001 (VPP=12.5V) Please input code No.=1000 SELECT 1004=uPD27256 10C4=uPD27256A 1025=uPD27C512 (VPP=21V)
10A4=uPD27C256
(VPP=21V)
(VPP=12.5V) (F/N) (VPP=12.5V) (F/N)
1064=uPD27C256A (VPP=12.5V) (F/N) 1086=uPD27C1000 (VPP=12.5V) 1046=uPD27C1001 (VPP=12.5V) 1026=uPD27C1024 (VPP=12.5V) 10C7=uPD27C2001 (VPP=12.5V) (P/N) 10A8=uPD27C4096 (VPP=12.5V)
1016=uPD27C1000A (VPP=12.5V) (P/N) 10D6=uPD27C1001A (VPP=12.5V) (P/N) 10B6=uPD27C1024A (VPP=12.5V) (P/N) 10C8=uPD27C4001 (VPP=12.5V) Please input code No.=
number displayed input, message "Please input code displayed again. exit from subcommand press key. With board Subcommand cannot used. attempt made subcommand, error message displayed.
RG\RS ERR39 Adaptor board connected
CHAPTER
TERMINAL MODE
[Execution example PG\RS With µPD75P108B During normal execution
PG\RS Your setting D75P108B
error occurs
PG\RS ERR32 Signature read error
[Execution example
PG\RS (only select mode)
PG\RS
silicon signature been read when only command been executed. read when command executed.
CHAPTER
TERMINAL MODE
6.1.3
command Compares data device inserted socket with data internal memory PG-1500.
[Function]
[Input format]
PG\RV
[ROM_S_ADR] [,ROM_E_ADR] [,PG_S_ADR] [,SPLIT]
ROM_S_ADR Input (PROM start address). ROM_E_ADR Input (PROM address). PG_S_ADR SPLIT [Execution example] case Input (PG-1500 buffer start address). Select (address partition type). ROM_S_ADR 00000 ROM_E_ADR 01FFF PG_S_ADR SPLIT 00000
During normal execution
PG\RV 0,1FFF,0,N data reading
Data complete Check 78D6
error occurs during verification
PG\RV 0,FFFF,0,BE data reading ERR20 Data completed 00000 data data
Continue (Y:Yes/N:No)?
CHAPTER
TERMINAL MODE
message [Continue (Y:Yes/N:No)?] displayed during execution, input response. Table shows operation performed when input. Table 6-5. Input Functions during Command Error
Input Others
Function Executes verification again starting from address next that displayed Aborts verification Displays [Continue] message again
[Abbreviated format]
terminal mode, commands input abbreviated format. Table shows variations abbreviations.
CHAPTER
TERMINAL MODE
Table 6-6. Abbreviated Formats Command
Input Format ROM_S_ADR,ROM_E_ADR,PG_S_ADR, ROM_S_ADR,ROM_E_ADR,PG_S_ADR ROM_S_ADR,ROM_E_ADR,,SPLIT ROM_S_ADR,ROM_E_ADR,, ROM_S_ADR,ROM_E_ADR ROM_S_ADR,,PG_S_ADR,SPLIT ROM_S_ADR,,PG_S_ADR, ROM_S_ADR,,PG_S_ADR ROM_S_ADR,,,SPLIT ROM_S_ADR,,, ROM_S_ADR,, ROM_S_ADR, ROM_S_ADR ,ROM_E_ADR,PG_S_ADR,SPLIT ,ROM_E_ADR,PG_S_ADR, ,ROM_E_ADR,PG_S_ADR ,ROM_E_ADR,,SPLIT ,ROM_E_ADR,, ,ROM_E_ADR ,,PG_S_ADR,SPLIT ,,PG_S_ADR, ,,PG_S_ADR ,,,SPLIT
ROM_S_ADR Address input Address input Address input Address input Address input Address input Address input Address input Address input Address input Address input Address input Address input Address input
ROM_E_ADR Address input Address input Address input Address input Address input Address input Address input Address input Address input Address input Address input Address input Note ROM_E_ADR
PG_S_ADR Address input Address input Address input Address input Address input Address input Address input Address input Address input Address input Address input Address input
SPLIT Input Input Input Input Input Input Input Input
Remark
Note Note Note Note Note Note Note Note
Notes ROM_S_ADR ROM_E_ADR, error occurs. Input address selected when selected SELECT. When selected, input address silicon signature data previously read. When selected, input address read silicon signature data.
CHAPTER
TERMINAL MODE
6.1.4
command Writes data specified address internal memory PG-1500 those that follow specified address range device inserted socket written.
[Function]
[Input format]
PG\RW
[ROM_S_ADR] [,ROM_E_ADR] [,PG_S_ADR] [,SPLIT]
ROM_S_ADR Input (PROM start address). ROM_E_ADR Input (PROM address). PG_S_ADR SPLIT [Execution example] case Input (PG-1500 buffer start address). Select (address partition type). ROM_S_ADR 00000 ROM_E_ADR 01FFF PG_S_ADR SPLIT 00000
During normal execution
PG\RW 0,1FFF,0,N data writing Data complete Check sum: 78D6
error occurs during verification
PG\RW 0,FFFF,0,BE data writing ERR20 Data completed 00000 data data
Continue (Y:Yes/N:No)?
CHAPTER
TERMINAL MODE
message [Continue (Y:Yes/N:No)?] displayed during execution, input response. Table shows operation performed when input. Table 6-7. Input Functions during Command Error
Input Others
Function Executes verification again starting from address next that displayed Aborts writing Displays [Continue] message again
[Abbreviated format]
terminal mode, commands input abbreviated format. Table shows variations abbreviations.
CHAPTER
TERMINAL MODE
Table 6-8. Abbreviated Formats Command
Input Format ROM_S_ADR,ROM_E_ADR,PG_S_ADR, ROM_S_ADR,ROM_E_ADR,PG_S_ADR ROM_S_ADR,ROM_E_ADR,,SPLIT ROM_S_ADR,ROM_E_ADR,, ROM_S_ADR,ROM_E_ADR ROM_S_ADR,,PG_S_ADR,SPLIT ROM_S_ADR,,PG_S_ADR, ROM_S_ADR,,PG_S_ADR ROM_S_ADR,,,SPLIT ROM_S_ADR,,, ROM_S_ADR,, ROM_S_ADR, ROM_S_ADR ,ROM_E_ADR,PG_S_ADR,SPLIT ,ROM_E_ADR,PG_S_ADR, ,ROM_E_ADR,PG_S_ADR ,ROM_E_ADR,,SPLIT ,ROM_E_ADR,, ,ROM_E_ADR ,,PG_S_ADR,SPLIT ,,PG_S_ADR, ,,PG_S_ADR ,,,SPLIT
ROM_S_ADR Address input Address input Address input Address input Address input Address input Address input Address input Address input Address input Address input Address input Address input Address input
ROM_E_ADR Address input Address input Address input Address input Address input Address input Address input Address input Address input Address input Address input Address input Note ROM_E_ADR
PG_S_ADR Address input Address input Address input Address input Address input Address input Address input Address input Address input Address input Address input Address input
SPLIT Input Input Input Input Input Input Input Input
Remark
Note Note Note Note Note Note Note Note
Notes ROM_S_ADR ROM_E_ADR, error occurs. Input address selected when selected SELECT. When selected, input address silicon signature data previously read. When selected, input address read silicon signature data.
CHAPTER
TERMINAL MODE
6.1.5
command Checks whether device inserted socket been written. PG\RZ
[Function] [Input format] [Execution example]
During normal execution
PG\RZ erase
data erased
PG\RZ ERR28 erased 00000 data
Continue (Y:Yes/N:No)?
message [Continue (Y:Yes/N:No)?] displayed during execution, input response. Table shows operation performed when input. Table 6-9. Input Functions during Command Error
Input Others
Function Executes blank check again starting from address next that displayed Aborts blank check Displays [Continue] message again
CHAPTER
TERMINAL MODE
Commands
Three commands available: "MC", "MD", "MF". function, input format, execution example, abbreviated format each command described below. 6.2.1 command Changes contents PG-1500's internal memory. PG\MC [PG_S_ADR]
[Function] [Input format]
PG_S_ADR: Input (PG-1500 buffer start address). [Execution example] Where PG_S_ADR
PG\MC 00100
this status, following data keys input: Table 6-10. Data That Input during Command Execution Their Functions
Input 2-digit hexadecimal data Space Return Changes data
Function
Does change data displays data next address Ends changing data
[Abbreviated format]
terminal mode, command input abbreviated format. Table 6-11 shows variations abbreviated formats command. Table 6-11. Abbreviated Formats Command
Input Format PG_S_ADR
PG_S_ADR Address input
CHAPTER
TERMINAL MODE
6.2.2
command Displays data specified range internal memory PG-1500. PG\MD [PG_S_ADR] [,PG_E_ADR]
[Function] [Input format]
PG_S_ADR: Input (PG-1500 buffer start address). PG_E_ADR: Input (PG-1500 buffer address). [Execution example] case PG_S_ADR PG_E_ADR
PG\MD 0,FF PG_A 00000 00010 00020 00030 00040 00050 00060 00070 00080 00090 000A0 000B0 000C0 000D0 000E0 000F0
CHAPTER
TERMINAL MODE
After instruction been executed while data displayed, following keys valid: Table 6-12. Keys That Input during Command Execution Their Functions
Input CTRL+S CTRL+Q Space
Function Aborts display Resumes display Stops display
[Abbreviated format]
terminal mode, command input abbreviated format. Table 6-13 shows variations abbreviated formats command. Table 6-13. Abbreviated Formats Command
Input Format PG_S_ADR,PG_E_ADR PG_S_ADR, PG_S_ADR ,PG_E_ADR
PG_S_ADR Address input Address input Address input
PG_E_ADR Address input PG_S_ADR+FFH Address input
Remark
Note
Note PG_S_ADR PG_E_ADR, error occurs.
CHAPTER
TERMINAL MODE
6.2.3
command Initializes contents internal memory PG-1500 specified range with specified data.
[Function]
[Input format]
PG\MF
[PG_S_ADR] [,PG_E_ADR] [,INT_DATA]
PG_S_ADR Input (PG-1500 buffer start address). PG_E_ADR Input (PG-1500 buffer address). INT_DATA (Initialization data) [Execution example] case ROM_S_ADR 00000 ROM_E_ADR 0FFFF INT_DATA
PG\MF 0,FFFF,FF
[Abbreviated format]
terminal mode, command input abbreviated format. Table 6-14 shows variations abbreviated formats command. Table 6-14. Abbreviated Formats Command
Input FormatNote PG_S_ADR,PG_E_ADR,INT_DATA PG_S_ADR,,INT_DATA ,PG_E_ADR,INT_DATA ,,INT_DATA
PG_S_ADR Address input Address input
PG_E_ADR Address input Address input
INT_DATA Data input Data input Data input Data input
Remark
Note
Notes input format other than these causes error. PG_S_ADR PG_E_ADR, error occurs.
CHAPTER
TERMINAL MODE
Commands
Three commands available: "LI", "LM", "LT". function, input format, execution example, abbreviated format each command described below. [Function] Transfers file Intel format, Motorola format, expanded format memory PG-1500. [Input format] PG\LI PG\LM PG\LT
Input above.
CHAPTER
TERMINAL MODE
[Execution example]
PG\LI
PG\LI FILENAME=TEST. Load Complete
abort loading, input key. When loading stopped, PG1500C automatically closes file.
PG\LI FILENAME=TEST. LOAD ADDRESS. [0000:00A0] Execution aborted input here.
error occurs such that specified file cannot found, that file cannot opened, error message displayed (refer "CHAPTER ERROR MESSAGES").
CHAPTER
TERMINAL MODE
Commands
Three commands available: "SI", "SM", "ST". function, input format, execution example, abbreviated format each command described below. [Function] Saves data from PG_S_ADR PG_E_ADR Intel format, Motorola format, expanded format, accordance with specified file name. [Input format] PG\SI [PG_S_ADR] [,PG_E_ADR]
PG\SM [PG_S_ADR] [,PG_E_ADR] PG\ST [PG_S_ADR] [,PG_E_ADR]
<1>: Input PG_S_ADR (PG-1500 buffer start address). <2>: Input PG_E_ADR (PG-1500 buffer address). Input above. [Execution example] PG\SI 00000, 01FFF
PG\SI 00000,01FFF FILENAME=TEST. Save Complete
CHAPTER
TERMINAL MODE
file name input, data sent from PG-1500 displayed screen. abort saving, input key. When saving stopped, PG1500C automatically closes file erases saved file.
PG\SI 0,1FFF FILENAME=TEST. SAVE ADDRESS. [0000:00A0] Execution aborted input here.
error occurs such that file cannot opened, error message displayed (refer "CHAPTER ERROR MESSAGES"). [Abbreviated format] terminal mode, command input abbreviated format. Table 6-15 shows variations abbreviated formats command. Table 6-15. Abbreviated Formats Command
Input Format PG_S_ADR,PG_E_ADR ,PG_E_ADR PG_S_ADR, PG_S_ADR
PG_S_ADR Address input Address input Address input
PG_E_ADR Address input Address input PG_S_ADR+FFH
Remark
Note
Note PG_S_ADR PG_E_ADR, error occurs.
CHAPTER
TERMINAL MODE
Commands
Three commands available: "PI", "PM", "PT". function, input format, execution example, abbreviated format each command described below. [Function] Transfers specified file Intel format, Motorola format, expanded format memory PG-1500 parallel I/F. [Input format] [Execution example] PG\PI PG\PM PG\PT
PG\PI
PG\PI FILENAME=TEST.HEX Load Complete
error occurs such that specified file cannot found, that file cannot opened, error message displayed (refer "CHAPTER ERROR MESSAGES").
CHAPTER
TERMINAL MODE
Command
function, input format, execution example command described below. [Function] Command help. Displays input formats functions commands terminal mode. [Input format] [Execution example] PG\??
PG\?? [PG_S_ADR] [PG_S_ADR][,PG_E_ADR] [PG_S_ADR][,PG_E_ADR],INIT_DATA [PG_S_ADR][,PG_E_ADR] [PG_S_ADR][,PG_E_ADR] [PG_S_ADR][,PG_E_ADR]
DATA READ SELECT (SIGNATURE READ) SELECT (SIGNATURE AUTO READ) SELECT (CODE SELECT) VERIFY (MASTER PG_BUFFER) WRITE (PG_BUFFER ROM) ZERO CHECK (BLANK CHECK) CHANGE PG_BUFFER DATA DISPLAY PG_BUFFER DATA INITIALIZE PG_BUFFER SERIAL LOAD (Intel_HEX) SERIAL LOAD (Motorola_S) SERIAL LOAD (Tektronix_HEX) SAVE (Intel_HEX) SAVE (Motorola_S) SAVE (Tektronix_HEX) PARALLEL LOAD (Intel_HEX) PARALLEL LOAD (Motorola_S) PARALLEL LOAD (Tektronix_HEX)
CHAPTER
TERMINAL MODE
Command
Starts SHELL once returns control Inputting EXIT causes terminal mode set.
[Function]
[Input format] [Execution example]
PG\OS
PG\OS A\EXIT Terminal mode PG1500C Prompt
CHAPTER
ERROR MESSAGES
CHAPTER
ERROR MESSAGES
Error ERR10
Display
Action Specify start address higher than address. specified address must lower than last address ROM.
START_ADR larger than END_ADR ERR11 Address large
ERR12 Address requires less than 7FFFF
Specify address that does exceed last address PG-1500 buffer.
ERR13 Mismatch with split mode
Check name split mode. Either replace change split mode (for details address split mode, refer "PG-1500 User's Manual").
ERR14 Illegal character (only hexadecimal)
Only hexadecimal numbers used input addresses data.
ERR15 Illegal split mode Split mode
Only specified symbols used specify address split mode (for details, refer Figures through 4-5).
ERR16 Command syntax error
Check input format command. Correctly input command.
ERR17 Illegal command
Correctly input command. Correctly input file name.
ERR1A File found
ERR1B Illegal option
Only used symbols specify options. Correctly specify option with
ERR1C File can't open
Correctly input file name.
CHAPTER
ERROR MESSAGES
Error ERR1D Illegal parameter
Display
Action input anything after option start PG1500C terminal mode.
ERR1E Configuration completed
Necessary parameters written configuration file. Make correct setting. This message displayed when PG1500C AUTO mode.
ERR20 Data completed xxxxx data xxxx data xxxx
Writing data failed. Input accordance with message. When input, verification continued starting from next address. When
Continue Yes/N: change ROM. Retry Yes/N:
Note
input, PG1500C returns command input wait status. Write data again.
Note message shown below broken line displayed only when input response message "Continue Yes/N: No)?" that displayed when AUTO command executed auto control mode.
CHAPTER
ERROR MESSAGES
Error
Display ERR21 Data completed xxxxx data xxxx data xxxx
Action data match buffer data. Input accordance with message. When input, verification continued starting from next address. When
Continue Yes/N: change ROM. Retry Yes/N:
Note
input, PG1500C returns command input wait status. This error occurs when 5.25
ERR22 Data completed xxxxx data xxxx data xxxx
data match buffer data. Input accordance with message. When input, verification continued starting from next address. When
Continue Yes/N: change ROM. Retry Yes/N:
Note
input, PG1500C returns command input wait status. This error occurs when 4.75
ERR28 Data erased xxxxx data xxxx
Data written ROM. Take following actions: write data, replace ROM. continue blank check, input
Continue Yes/N: change ROM. Retry Yes/N:
Note
accordance with message. When input, blank check continued starting from next address. When input, PG1500C returns command input wait status.
Note message shown below broken line displayed only when input response message "Continue Yes/N: No)?" that displayed when AUTO command executed auto control mode.
CHAPTER
ERROR MESSAGES
Error ERR2C Write error xxxxx data xxxx
Display
Action Data cannot correctly written. Take following actions: Check whether matches selected name. they match,
Continue Yes/N: change ROM. Retry Yes/N: No)?
Note
defective connection faulty. Replace ROM. continue writing starting from next address, input accordance with message. When input, writing continued starting from next address. When input, PG1500C returns command input wait status. Note, however, that data address which error occurred correctly written.
ERR30 Signature read error change ROM. Retry Yes/N: No)?
Note
Silicon signature data cannot read from ROM. Replace ROM.
Notes message shown below broken line displayed only when input response message "Continue Yes/N: No)?" that displayed when AUTO command executed auto control mode. message shown below broken line displayed only when AUTO command executed auto control mode.
CHAPTER
ERROR MESSAGES
Error ERR31
Display
Action different from selected ROM. Check name
Note
signature different from configuration Change ROM. Retry Yes/N: No)?
corresponding generalpurpose PROM name, take following actions: When AUTO command used auto control mode, change setting configuration file configuration area. other case, redo selection.
ERR32 Signature read error change ROM. Retry Yes/N: No)?
Note
Silicon signature data cannot read from ROM. Replace ROM. check name corresponding generalpurpose PROM name, redo selection.
ERR38 Device miss insertion
set, inserted wrong direction. Correctly insert ROM.
ERR39 Adaptor board connected
adaptor board correctly connected. Correctly connect adaptor board.
Note message shown below broken line displayed only when AUTO command executed auto control mode.
CHAPTER
ERROR MESSAGES
Error ERR40
Display
Action serial cable correctly connected. Check cable connection. cable correctly connected,
Serial ready (Check cable, baud rate, data length, etc.) Select Q/QUIT retry. B/BAUD RATE P/PARITY X/XON C/DATA LENGTH S/STOP Q/QUIT ERR41 File data error 1200 2400 EVEN bits 4800 9600 19200
bauds setting serial PG-1500 different from that host bits machine. Match setting.
specified file cannot used. Specify file that used.
ERR51 File can't close
file name wrong. Input correct file name. Insert floppy disk containing COMMAND.COM into current drive.
COMMAND.COM found
Save failed (File write error)
Check specification configuration file capacity floppy disk. Retry.
Can't
must number sets. Specify more.
Save failed (File write error)
capacity floppy disk short.
Parallel ready (Check parallel cable, etc.)
parallel correctly connected. Terminate PG1500C once, turn power, check connections, then restart PG1500C.
APPENDIX
EXAMPLE OPERATION CONTROL MODE
APPENDIX
EXAMPLE OPERATION CONTROL MODE
File PROM Auto Write
write file PROM automatically using command, each parameter configuration area. Select A/AUTO.
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512 <Message> CONFIG FILE TEST.PGC Please select command.
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
A/AUTO
R/ROM
M/MEM
L/LOAD
S/SAVE
O/OS
C/CONF
Q/QUIT
APPENDIX
EXAMPLE OPERATION CONTROL MODE
Input number sets.
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512 <Message> CONFIG FILE TEST.PGC
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
Number
A/AUTO
R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512
<Message> CONFIG FILE TEST.PGC
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
Number
select
Check: UPD27C512
A/AUTO
R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
APPENDIX
EXAMPLE OPERATION CONTROL MODE
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512
<Message> CONFIG FILE TEST.PGC
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
Number Check: UPD27C512
File transfer PG-1500 buffer
File Loading LOAD ADDRESS [0000:01E0]
A/AUTO
R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512
<Message> CONFIG FILE TEST.PGC
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
Number Check: UPD27C512 File Loading Writing (NN)
Checking erasure status
erase
A/AUTO
R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
APPENDIX
EXAMPLE OPERATION CONTROL MODE
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512
<Message> CONFIG FILE TEST.PGC
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
Number Check: UPD27C512 File Loading Writing (NN) erase
Writing data
Now, data writing!
A/AUTO
R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
Writing complete
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512 <Message> CONFIG FILE TEST.PGC Please select command.
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
Number Check: UPD27C512 File Loading Writing (NN) erase Now, data writing! Data complete
Check display
Check sum: 78D6 Write completed
A/AUTO
R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
APPENDIX
EXAMPLE OPERATION CONTROL MODE
File Buffer Read
Select L/LOAD.
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512 <Message> CONFIG FILE TEST.PGC Please select command.
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
A/AUTO R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
APPENDIX
EXAMPLE OPERATION CONTROL MODE
Select "START" press parameters changed.
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512
<Message> CONFIG FILE TEST.PGC
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
FILENAME B\ABCD\EFG\TEST.HEX FORMAT Intel_HEX INTERFACE START SERIAL Motorola_S Tektronix_HEX PARALLEL
A/AUTO R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
Load complete
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512 <Message> CONFIG FILE TEST.PGC Please select command.
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
FILENAME B\ABCD\EFG\TEST.HEX FORMAT Intel_HEX INTERFACE SERIAL Motorola_S PARALLEL Tektronix_HEX
Load Complete
A/AUTO R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
APPENDIX
EXAMPLE OPERATION CONTROL MODE
PROM Buffer Read
Select R/ROM.
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512 <Message> CONFIG FILE TEST.PGC Please select command.
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
A/AUTO R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
APPENDIX
EXAMPLE OPERATION CONTROL MODE
Select S/SELECT ROM.
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512 <Message> CONFIG FILE TEST.PGC Please Please select command
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
R/DATA READ S/SELECT V/VERIFY (MASTER PG_BUFFER) W/WRITE (PG_BUFFER ROM) Z/ZERO CHECK (BLANK CHECK)
A/AUTO R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
Select R/SIGNATURE READ.
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512 <Message> CONFIG FILE TEST.PGC Please ROM. Please select command.
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
RS/SELECT R/SIGNATURE READ A/SIGNATURE AUTO READ C/CODE SELECT
name PROM displayed.
Your setting uPD27C256A
A/AUTO R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
APPENDIX
EXAMPLE OPERATION CONTROL MODE
Select R/ROM.
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512 <Message> CONFIG FILE TEST.PGC Please select command.
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
A/AUTO R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
Select R/DATA READ.
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512 <Message> CONFIG FILE TEST.PGC
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
R/DATA READ S/SELECT V/VERIFY (MASTER PG_BUFFER) W/WRITE (PG_BUFFER ROM) Z/ZERO CHECK (BLANK CHECK)
A/AUTO R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
APPENDIX
EXAMPLE OPERATION CONTROL MODE
Select "START" press parameters changed.
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512
<Message> CONFIG FILE TEST.PGC
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
RR/DATA READ START ADDRESS ADDRESS CONV START 00000 07FFF
PG_BUFFER START ADDRESS 00000
A/AUTO R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
Read complete
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512 <Message> CONFIG FILE TEST.PGC Please select command.
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
RS/DATA READ START ADDRESS ADDRESS CONV Now, data reading! Data complete 00000 07FFF
PG_BUFFER START ADDRESS 00000
Check display
Check sum: 78D6
A/AUTO R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
APPENDIX
EXAMPLE OPERATION CONTROL MODE
Buffer General-purpose PROM Write
Select R/ROM.
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512 <Message> CONFIG FILE TEST.PGC Please select command.
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
A/AUTO R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
APPENDIX
EXAMPLE OPERATION CONTROL MODE
Select S/SELECT ROM.
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512 <Message> CONFIG FILE TEST.PGC Please ROM.
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
R/DATA READ S/SELECT V/VERIFY (MASTER PG_BUFFER) W/WRITE (PG_BUFFER ROM) Z/ZERO CHECK (BLANK CHECK)
A/AUTO R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
Select R/SIGNATURE READ.
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512 <Message> CONFIG FILE TEST.PGC Please ROM. Please select command.
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
RS/SELECT R/SIGNATURE READ A/SIGNATURE AUTO READ C/CODE SELECT
name PROM displayed.
Your setting uPD27C256A
A/AUTO R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
APPENDIX
EXAMPLE OPERATION CONTROL MODE
Select R/ROM.
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512 <Message> CONFIG FILE TEST.PGC Please select command.
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
A/AUTO R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
Select Z/ZERO CHECK (BLANK CHECK).
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512 <Message> CONFIG FILE TEST.PGC
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
R/DATA READ S/SELECT V/VERIFY (MASTER PG_BUFFER) W/WRITE (PG_BUFFER ROM) Z/ZERO CHECK (BLANK CHECK)
A/AUTO R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
APPENDIX
EXAMPLE OPERATION CONTROL MODE
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512
<Message> CONFIG FILE TEST.PGC Please select command.
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
RZ/ZERO CHECK (BLANK CHECK)
contents have been erased, "ROM erase OK!" displayed.
erase
A/AUTO R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
Select R/ROM.
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512 <Message> CONFIG FILE TEST.PGC Please select command.
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
A/AUTO R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
APPENDIX
EXAMPLE OPERATION CONTROL MODE
Select W/WRITE (PG_BUFFER ROM).
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512
<Message> CONFIG FILE TEST.PGC Please ROM.
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
R/DATA READ S/SELECT V/VERIFY (MASTER PG_BUFFER) W/WRITE (PG_BUFFER ROM) Z/ZERO CHECK (BLANK CHECK)
A/AUTO R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
Select "START" press parameters changed.
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512 <Message> CONFIG FILE TEST.PGC
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
RW/WRITE (PG_BUFFER ROM) START ADDRESS ADDRESS 00000 07FFF
PG_BUFFER START ADDRESS 00000 SPLIT MODE START
A/AUTO R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
APPENDIX
EXAMPLE OPERATION CONTROL MODE
Writing complete
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512 <Message> CONFIG FILE TEST.PGC Please select command.
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
RW/WRITE (PG_BUFFER ROM) START ADDRESS ADDRESS 00000 07FFF
PG_BUFFER START ADDRESS 00000 SPLIT MODE Now, data writing! Data complete
Check display
Check sum: 78D6
A/AUTO R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
APPENDIX
EXAMPLE OPERATION CONTROL MODE
Buffer Silicon Signature Compatible ProductNote Write
Note Refer "PG-1500 User's Manual" silicon signature compatible products. Select R/ROM.
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512 <Message> CONFIG FILE TEST.PGC Please select command.
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
A/AUTO R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
APPENDIX
EXAMPLE OPERATION CONTROL MODE
Select S/SELECT ROM.
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512 <Message> CONFIG FILE TEST.PGC Please ROM.
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
R/DATA READ S/SELECT V/VERIFY (MASTER PG_BUFFER) W/WRITE (PG_BUFFER ROM) Z/ZERO CHECK (BLANK CHECK)
A/AUTO R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
Select R/SIGNATURE READ.
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512 <Message> CONFIG FILE TEST.PGC Please ROM. Please select command.
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
RS/SELECT R/SIGNATURE READ A/SIGNATURE AUTO READ C/CODE SELECT
name PROM displayed.
Your setting D75P108B
A/AUTO R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
APPENDIX
EXAMPLE OPERATION CONTROL MODE
Select R/ROM.
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512 <Message> CONFIG FILE TEST.PGC Please select command.
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
A/AUTO R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
Select Z/ZERO CHECK (BLANK CHECK).
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512
<Message> CONFIG FILE TEST.PGC
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
R/DATA READ S/SELECT V/VERIFY (MASTER PG_BUFFER) W/WRITE (PG_BUFFER ROM) Z/ZERO CHECK (BLANK CHECK)
A/AUTO R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
APPENDIX
EXAMPLE OPERATION CONTROL MODE
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512
<Message> CONFIG FILE TEST.PGC Please select command.
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
RZ/ZERO CHECK (BLANK CHECK)
contents have been erased, "ROM erase OK!" displayed.
erase
A/AUTO R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
Select R/ROM.
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512 <Message> CONFIG FILE TEST.PGC Please select command.
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
A/AUTO R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
APPENDIX
EXAMPLE OPERATION CONTROL MODE
Select W/WRITE (PG_BUFFER ROM).
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512
<Message> CONFIG FILE TEST.PGC
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
R/DATA READ S/SELECT V/VERIFY (MASTER PG_BUFFER) W/WRITE (PG_BUFFER ROM) Z/ZERO CHECK (BLANK CHECK)
A/AUTO R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
Select "START" press parameters changed.
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512 <Message> CONFIG FILE TEST.PGC
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
RW/WRITE (PG_BUFFER ROM) START ADDRESS ADDRESS 00000 01FFF
PG_BUFFER START ADDRESS 00000 SPLIT MODE START
A/AUTO R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
APPENDIX
EXAMPLE OPERATION CONTROL MODE
Writing complete
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512 <Message> CONFIG FILE TEST.PGC Please select command.
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
RW/WRITE (PG_BUFFER ROM) START ADDRESS ADDRESS 00000 01FFF
PG_BUFFER START ADDRESS 00000 SPLIT MODE Now, data writing! Data complete
Check display
Check sum: 78D6
A/AUTO R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
APPENDIX
EXAMPLE OPERATION CONTROL MODE
Buffer Silicon Signature Non-Compatible ProductNote Write
Note Refer "PG-1500 User's Manual" silicon signature non-compatible products. Select R/ROM.
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512 <Message> CONFIG FILE TEST.PGC Please select command.
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
A/AUTO R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
APPENDIX
EXAMPLE OPERATION CONTROL MODE
Select S/SELECT ROM.
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512 <Message> CONFIG FILE TEST.PGC
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
R/DATA READ S/SELECT V/VERIFY (MASTER PG_BUFFER) W/WRITE (PG_BUFFER ROM) Z/ZERO CHECK (BLANK CHECK)
A/AUTO R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
Select C/CODE SELECT.
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512 <Message> CONFIG FILE TEST.PGC ROM.
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
RS/SELECT R/SIGNATURE READ A/SIGNATURE AUTO READ C/CODE SELECT
code number list displayed.
SELECT 10C4=uPD27256A 1064=uPD27C256A 1025=uPD27C512 (VPP=12.5V) (F/N) (VPP=12.5V) (F/N) (VPP=12.5V) (F/N) 1004=uPD27256 10A4=uPD27C256 (VPP=21V) (VPP=21V)
1086=uPD27C1000 (VPP=12.5V) 1046=uPD27C1001 (VPP=12.5V) 1026=uPD27C1024 (VPP=12.5V) 10C7=uPD27C2001 (VPP=12.5V) (P/N) 10A8=uPD27C4096 (VPP=12.5V)
1016=uPD27C1000A (VPP=12.5V) (P/N) 10D6=uPD27C1001A (VPP=12.5V) (P/N) 10B6=uPD27C1024A (VPP=12.5V) (P/N) 10C8=uPD27C4001 (VPP=12.5V) Please input code No.=
A/AUTO R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
APPENDIX
EXAMPLE OPERATION CONTROL MODE
Input code number corresponding general-purpose PROM. Select (Normal).
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512
<Message> CONFIG FILE TEST.PGC Please select command.
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END RS/SELECT R/SIGNATURE READ A/SIGNATURE AUTO READ C/CODE SELECT SELECT 10C4=uPD27256A 1064=uPD27C256A 1025=uPD27C512 (VPP=12.5V) (F/N) (VPP=12.5V) (F/N) (VPP=12.5V) (F/N) 1004=uPD27256 10A4=uPD27C256 (VPP=21V) (VPP=21V) SERIAL
1086=uPD27C1000 (VPP=12.5V) 1046=uPD27C1001 (VPP=12.5V) 1026=uPD27C1024 (VPP=12.5V) 10C7=uPD27C2001 (VPP=12.5V) (P/N) 10A8=uPD27C4096 (VPP=12.5V)
1016=uPD27C1000A (VPP=12.5V) (P/N) 10D6=uPD27C1001A (VPP=12.5V) (P/N) 10B6=uPD27C1024A (VPP=12.5V) (P/N) 10C8=uPD27C4001 (VPP=12.5V) Please input code No.=1064
Please input program mode (Page/Fast/Normal)=N A/AUTO R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
SELECT R/ROM.
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512 <Message> CONFIG FILE TEST.PGC Please select command.
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
A/AUTO R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
APPENDIX
EXAMPLE OPERATION CONTROL MODE
Select Z/ZERO CHECK (BLANK CHECK).
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512
<Message> CONFIG FILE TEST.PGC
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
R/DATA READ S/SELECT V/VERIFY (MASTER PG_BUFFER) W/WRITE (PG_BUFFER ROM) Z/ZERO CHECK (BLANK CHECK)
A/AUTO R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512
<Message> CONFIG FILE TEST.PGC Please select command.
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
RZ/ZERO CHECK (BLANK CHECK)
contents have been erased, "ROM erase OK!" displayed.
erase
A/AUTO R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
APPENDIX
EXAMPLE OPERATION CONTROL MODE
Select R/ROM.
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512 <Message> CONFIG FILE TEST.PGC Please select command.
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
A/AUTO R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
Select W/WRITE (PG_BUFFER ROM).
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512
<Message> CONFIG FILE TEST.PGC Please ROM.
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
R/DATA READ S/SELECT V/VERIFY (MASTER PG_BUFFER) W/WRITE (PG_BUFFER ROM) Z/ZERO CHECK (BLANK CHECK)
A/AUTO R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
APPENDIX
EXAMPLE OPERATION CONTROL MODE
<10> Select "START" press parameters changed.
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512
<Message> CONFIG FILE TEST.PGC
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
RW/WRITE (PG_BUFFER ROM) START ADDRESS ADDRESS 00000 07FFF
PG_BUFFER START ADDRESS 00000 SPLIT MODE START
A/AUTO R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
<11> Writing complete
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512 <Message> CONFIG FILE TEST.PGC Please select command.
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
RW/WRITE (PG_BUFFER ROM) START ADDRESS ADDRESS 00000 07FFF
PG_BUFFER START ADDRESS 00000 SPLIT MODE Now, data writing! Data complete
Check display
Check sum: 78D6
A/AUTO R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
APPENDIX
EXAMPLE OPERATION CONTROL MODE
Verification Contents Buffer PROM
Select R/ROM.
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512 <Message> CONFIG FILE TEST.PGC Please select command.
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
A/AUTO R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
APPENDIX
EXAMPLE OPERATION CONTROL MODE
Select S/SELECT ROM.
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512 <Message> CONFIG FILE TEST.PGC Please ROM.
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
R/DATA READ S/SELECT V/VERIFY (MASTER PG_BUFFER) W/WRITE (PG_BUFFER ROM) Z/ZERO CHECK (BLANK CHECK)
A/AUTO R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
Select R/SIGNATURE READ.
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512 <Message> CONFIG FILE TEST.PGC Please ROM. Please select command.
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
RS/SELECT R/SIGNATURE READ A/SIGNATURE AUTO READ C/CODE SELECT
name PROM displayed.
Your setting uPD27C256A
A/AUTO R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
APPENDIX
EXAMPLE OPERATION CONTROL MODE
Select R/ROM.
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512 <Message> CONFIG FILE TEST.PGC Please select command.
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
A/AUTO R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
Select V/VERIFY (MASTER PG_BUFFER).
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512 <Message> CONFIG FILE TEST.PGC
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
R/DATA READ S/SELECT V/VERIFY (MASTER PG_BUFFER) W/WRITE (PG_BUFFER ROM) Z/ZERO CHECK (BLANK CHECK)
A/AUTO R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
APPENDIX
EXAMPLE OPERATION CONTROL MODE
Select "START" press parameters changed.
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512
<Message> CONFIG FILE TEST.PGC
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
RV/VERIFY (MASTER PG_BUFFER) START ADDRESS ADDRESS 00000 07FFF
PG_BUFFER START ADDRESS 00000 SPLIT MODE START
A/AUTO R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
Verify complete
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512 <Message> CONFIG FILE TEST.PGC Please select command.
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
RV/VERIFY (MASTER PG_BUFFER) START ADDRESS ADDRESS 00000 07FFF
PG_BUFFER START ADDRESS 00000 SPLIT MODE Now, data reading! Data complete
Check display
Check sum: 78D6
W/AUTO R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
APPENDIX
EXAMPLE OPERATION CONTROL MODE
Buffer File Data Save
Select S/SAVE.
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512 <Message> CONFIG FILE TEST.PGC Please select command.
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
A/AUTO R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
APPENDIX
EXAMPLE OPERATION CONTROL MODE
Select "START" press parameters changed.
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512
<Message> CONFIG FILE TEST.PGC
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
FILENAME TEST2.HEX FORMAT PG_BUFFER ADDRESS START Intel_HEX 7FFFF Motorola_S Tektronix_HEX
PG_BUFFER START ADDRESS 00000
A/AUTO R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
Save complete
***** CONTROL MODE ***** F/FILENAME R/ROM TEST.HEX UPD27C512 <Message> CONFIG FILE TEST.PGC Please select command.
S/SPLIT MODE NORMAL H/HEX FORMAT Intel_HEX I/INTERFACE E/END SERIAL
FILENAME TEST2.HEX FORMAT PG_BUFFER ADDRESS Save Complete Intel_HEX 7FFFF Motorola_S Tektronix_HEX
PG_BUFFER START ADDRESS 00000
A/AUTO R/ROM M/MEM L/LOAD S/SAVE O/OS C/CONF Q/QUIT
Other recent searches
Z8018101ZCO - Z8018101ZCO Z8018101ZCO Datasheet
TLA-6T127LF - TLA-6T127LF TLA-6T127LF Datasheet
TLA-6T127LF-T - TLA-6T127LF-T TLA-6T127LF-T Datasheet
TLA-6T127LF - TLA-6T127LF TLA-6T127LF Datasheet
RKD750KP - RKD750KP RKD750KP Datasheet
PTC1111-90 - PTC1111-90 PTC1111-90 Datasheet
CTCH664F - CTCH664F CTCH664F Datasheet
BG2D - BG2D BG2D Datasheet
2SC4706 - 2SC4706 2SC4706 Datasheet
Privacy Policy | Disclaimer
© 2012 Datasheet Archive
