CMOS Quad Bilateral Switch CD4066BMS quad bilateral switch intend
|
|
|
Top Searches for this datasheet
CD4066BMS
CMOS Quad Bilateral Switch
CD4066BMS quad bilateral switch intended transmission multiplexing analog digital signals. compatible with CD4016B, exhibits much lower state resistance. addition, on-state resistance relatively constant over full input signal range. CD4066BMS consists four independent bilateral switches. single control signal required switch. Both device given switch biased simultaneously control signal. shown Figure well channel device each switch either tied input when switch when switch off. This configuration eliminates variation switch transistor threshold voltage with input signal, thus keeps on-state resistance over full operating signal range. advantages over single channel switches include peak input signal voltage swings equal full supply voltage, more constant on-state impedance over input signal range. sample hold applications, however, CD4016B recommended. CD4066BMS supplied these 14-lead outline packages:
Braze Seal Frit Seal Ceramic Flatpack
December 1992
Features
Transmission Multiplexing Analog Digital Signals High Voltage Types (20V Rating) Digital ±7.5V Peak-to-Peak Switching Typical On-State Resistance Operation Switch On-State Resistance Matched Within Over Signal Input Range On-State Resistance Flat Over Full Peak-to-Peak Signal Range High On/Off Output Voltage Ratio 80dB Typ. 10kHz, High Degree Linearity: <0.5% Distortion Typ. 1kHz, 5Vp-p, 10V, Extremely Off-State Switch Leakage Resulting Very Offset Current High Effective Off-State Resistance: 10pA Typ. 10V, +25oC Extremely High Control Input Impedance (Control Circuit Isolated from Signal Circuit): 1012 Typ. Crosstalk Between Switches: -50dB Typ. 8MHz, Matched Control Input Signal Output Capacitance: Reduces Output Signal Transients Frequency Response, Switch 40MHz (Typ.) 100% Tested Quiescent Current Parametric Ratings Meets Requirements JEDEC Tentative Standard 13B, "Standard Specifications Description Series CMOS Devices"
Pinout
CD4066BMS VIEW
IN/OUT OUT/IN
CONT CONT IN/OUT OUT/IN OUT/IN IN/OUT
Applications
Analog Signal Switching/Multiplexing Signal Gating Modulator Squelch Control Demodulator Chopper Commutating Switch Digital Signal Switching/Multiplexing Transmission Gate Logic Implementation Analog Digital Digital Analog Conversion Digital Control Frequency, Impedance, Phase, Analog Signal Gain
OUT/IN IN/OUT CONT CONT
CAUTION: These devices sensitive electrostatic discharge. Users should follow proper I.C. Handling Procedures. Copyright
Harris Corporation 1992
File Number
3319
7-966
Specifications CD4066BMS
Absolute Maximum Ratings
Supply Voltage Range, (VDD) -0.5V +20V (Voltage Referenced Terminals) Input Voltage Range, Inputs .-0.5V +0.5V Input Current, Input .±10mA Operating Temperature Range -55oC +125oC Package Types Storage Temperature Range (TSTG) -65oC +150oC Lead Temperature (During Soldering) +265oC Distance 1/16 1/32 Inch (1.59mm 0.79mm) from case Maximum
Reliability Information
Thermal Resistance Ceramic FRIT Package 80oC/W 20oC/W Flatpack Package 70oC/W 20oC/W Maximum Package Power Dissipation (PD) +125 -55oC +100oC (Package Type 500mW +100oC +125oC (Package Type Derate Linearity 12mW/oC 200mW Device Dissipation Output Transistor 100mW Full Package Temperature Range (All Package Types) Junction Temperature +175oC
TABLE ELECTRICAL PERFORMANCE CHARACTERISTICS GROUP SUBGROUPS 18V, Input Leakage Current Input Leakage Current Input/Output Leakage Current (Switch OFF) IOZL 18V, IOZH Resistance RON5 RON10 RON15 Resistance RON5 VDD, 10kW returned VSS/2 LIMITS TEMPERATURE +125oC -55oC +125oC -55oC +25oC +125oC -55oC +25oC +125oC -55oC +25oC +125oC -55oC +25oC +25oC +25oC +125oC -55oC Resistance RON10 +125oC -55oC Resistance RON15 +125oC -55oC Functional (Note 2.8V, 20V, 18V, Switch Threshold 100k Threshold Voltage Threshold Voltage SWTHRH5 1.5V, SWTHRH15 15V, VNTH VPTH 10V, -10µA 10µA +25oC +25oC +125oC -55oC +25oC, +125oC, -55oC +25oC, +125oC, -55oC +25oC +25oC 14.1 -2.8 -0.7
PARAMETER Supply Current
SYMBOL
CONDITIONS (NOTE 20V,
-100 -1000 -100 -100 -1000 -100 1050
1000 1000 1300
UNITS
VDD/2 VDD/2
7-967
Specifications CD4066BMS
TABLE ELECTRICAL PERFORMANCE CHARACTERISTICS GROUP SUBGROUPS LIMITS TEMPERATURE +25oC, +125oC, -55oC +25oC, +125oC, -55oC UNITS
PARAMETER Control Input Voltage (Note |IIS| 10µa, VSS, VDD, Control Input High Voltage (Note Figure
SYMBOL VILC5 VILC15
CONDITIONS (NOTE
VIHC
|IIS| .51mA, 4.6V 0.4V |IIS| .36mA, 4.6V 0.4V |IIS| .64mA, 4.6V 0.4V
+25oC +125oC -55oC +25oC +125oC -55oC
VIHC
15V, |IIS| 3.4mA, 13.5V <1.5V 15V, |IIS| 2.4mA, 13.5V 1.5V 15V, |IIS| 4.2mA, 13.5V <1.5V
NOTES: voltages referenced device GND, 100% testing being implemented. Go/No test with limits applied inputs.
2.8V/3.0V, 100K 20V/18V,
TABLE ELECTRICAL PERFORMANCE CHARACTERISTICS GROUP SUBGROUPS TEMPERATURE +25oC +125oC, -55oC LIMITS UNITS
PARAMETER Propagation Delay Signal Input Signal Output Propagation Delay Turn-On, Turn-Off NOTES:
SYMBOL TPLH TPHL
CONDITIONS (Notes
TPHZ/ZH (Notes TPLZ/ZL
+25oC +125oC, -55oC
50pF, Input 20ns. -55oC +125oC limits guaranteed, 100% testing being implemented. 50pF, 200K, Input 20ns. TABLE ELECTRICAL PERFORMANCE CHARACTERISTICS LIMITS PARAMETER Supply Current SYMBOL CONDITIONS NOTES TEMPERATURE -55oC, +25oC 0.25 UNITS
+125oC 10V, -55oC, +25oC +125oC 15V, -55oC, +25oC
+125oC Control Input Voltage |IIS| 10µa, VSS, VDD, VILC10 +25oC, +125oC, -55oC
7-968
Specifications CD4066BMS
TABLE ELECTRICAL PERFORMANCE CHARACTERISTICS (Continued) LIMITS PARAMETER Control Input High Voltage (See Figure Propagation Delay Signal Input Signal Output Propagation Delay Turn-On, Turn-Off Input Capacitance NOTES: voltages referenced device GND. parameters listed Table controlled design process directly tested. These parameters characterized initial design release upon design changes which would affect these characteristics. 50pF, 200K, Input 20ns. TABLE POST IRRADIATION ELECTRICAL PERFORMANCE CHARACTERISTICS LIMITS PARAMETER Supply Current Threshold Voltage Threshold Voltage Delta Threshold Voltage Threshold Voltage Delta Functional SYMBOL VNTH CONDITIONS 20V, 10V, -10µA 10V, -10µA 10µA 10µA 18V, Propagation Delay Time TPHL TPLH +25oC NOTES TEMPERATURE +25oC +25oC +25oC +25oC +25oC +25oC -2.8 VDD/2 -0.2 VDD/2 1.35 +25oC Limit UNITS SYMBOL VIHC10 TPLH TPHL CONDITIONS 10V, NOTES TEMPERATURE +25oC, +125oC, -55oC +25oC +25oC +25oC +25oC +25oC UNITS
TPHZ/ZH TPLZ/ZL Input
NOTES: voltages referenced device GND. 50pF, 200K, Input 20ns.
Table +25oC limit. Read Record
TABLE BURN-IN LIFE TEST DELTA PARAMETERS +25OC PARAMETER Supply Current Resistance SYMBOL RONDEL10 ±0.1µA Pre-Test Reading DELTA LIMIT
TABLE APPLICABLE SUBGROUPS CONFORMANCE GROUP Initial Test (Pre Burn-In) Interim Test (Post Burn-In) Interim Test (Post Burn-In) (Note Interim Test (Post Burn-In) (Note MIL-STD-883 METHOD 100% 5004 100% 5004 100% 5004 100% 5004 100% 5004 100% 5004 GROUP SUBGROUPS Deltas Deltas IDD, IOL5, IOH5A, RONDEL10 READ RECORD IDD, IOL5, IOH5A, RONDEL10 IDD, IOL5, IOH5A, RONDEL10 IDD, IOL5, IOH5A, RONDEL10
7-969
Specifications CD4066BMS
TABLE APPLICABLE SUBGROUPS (Continued) CONFORMANCE GROUP Final Test Group Group Subgroup Subgroup Group MIL-STD-883 METHOD 100% 5004 Sample 5005 Sample 5005 Sample 5005 Sample 5005 GROUP SUBGROUPS Deltas Subgroups Subgroups READ RECORD
NOTE: Parameteric, Functional; Cumulative Static
TABLE TOTAL DOSE IRRADIATION MIL-STD-883 METHOD 5005 TEST PRE-IRRAD POST-IRRAD Table READ RECORD PRE-IRRAD POST-IRRAD Table
CONFORMANCE GROUPS Group Subgroup
TABLE BURN-IN IRRADIATION TEST CONNECTIONS OSCILLATOR FUNCTION Static Burn-In (Note Static Burn-In (Note Dynamic Burn-In (Note Irradiation (Note NOTE: Each except will have series resistor 0.5V Each except will have series resistor Group Subgroup sample size dice/wafer, failures, 0.5V OPEN GROUND 4-8, 11-13 4-6, 11-14 4-6, 11-14 -0.5V 50kHz 25kHz
Functional Diagram
TRUTH TABLE EACH SWITCH
IN/OUT OUT/IN CONTROL
INPUT
OUTPUT Open Open
OUT/IN IN/OUT
CONTROL
IN/OUT
CONTROL
OUT/IN
Positive Logic: Switch Switch
CONTROL
OUT/IN
IN/OUT
7-970
CD4066BMS Schematic
SWITCH CONTROL NORMAL OPERATION CONTROL LINE BIASING: SWITCH SWITCH OFF,
CONTROL INPUTS PROTECTED CMOS PROTECTION NETWORK
CONTROL
SIGNAL LEVEL RANGE: NOTE: Substrates Connected
FIGURE SCHEMATIC DIAGRAM IDENTICAL SWITCHES ASSOCIATED CONTROL CIRCUITRY
CD4066BMS SWITCHES |VIS VOS| |IIS| "ON"
KEITHLY DIGITAL MULTIMETER RANGE PLOT
MOSELEY 7030A
FIGURE DETERMINATION TEST CONDITION CONTROL INPUT HIGH VOLTAGE (VIHC) SPECIFICATION
FIGURE CHANNEL ON-STATE RESISTANCE MEASUREMENT CIRCUIT
CIOS MEASURED BOONTON CAPACITANCE BRIDGE MODEL (1MHz) TEST FIXTURE CAPACITANCE NULLED
CD4066BMS SWITCHES
CD4066BMS SWITCHES
UNUSED TERMINALS CONNECTED
FIGURE CAPACITANCE TEST CIRCUIT
FIGURE SWITCH INPUT OUTPUT LEAKAGE
UNUSED INPUTS CONNECTED
+10V 20ns
UNUSED TERMINALS CONNECTED
CD4066BMS SWITCHES
200k
CD4066BMS SWITCHES
20ns
FIGURE PROPAGATION DELAY TIME SIGNAL INPUT (VIS) SIGNAL OUTPUT (VOS)
FIGURE CROSSTALK CONTROL INPUT SIGNAL OUTPUT
7-971
CD4066BMS
20ns 20ns 20ns RATE
20ns
UNUSED TERMINALS CONNECTED
+10V 20ns
+10V
UNUSED INPUTS CONNECTED
CD4066BMS SWITCHES
+10V
CD4066BMS SWITCHES
1/2VOS 1kHz
FIGURE PROPAGATION DELAY TPLH, TPHL CONTROL SIGNAL OUTPUT. DELAY MEASURED LEVEL +10% FROM GROUND (TURN ON-STATE OUTPUT LEVEL (TURN OFF).
FIGURE MAXIMUM ALLOWABLE CONTROL INPUT REPETITION RATE
CLOCK RESET
CLOCK CD4066B RESET
CD4018B
CD4018B
CD4049B
CD4049B
CD4001B
CD4001B CD4066B
CD4066B CD4049B
SIGNALS OUTPUTS CHANNEL
SIGNALS INPUTS
CHANNEL CHANNEL CHANNEL CHANNEL
CD4066B
CHANNEL
PACKAGE COUNT CD4001B CD4049B CD4066BMS CD4018B
CHANNEL
CLOCK MAX. ALLOWABLE SIGNAL LEVEL CHAN. CHAN. CHAN. CHAN.
(VDD VSS)
CHANNEL
FIGURE CHANNEL MULTIPLEX SYSTEM DIAGRAM
7-972
CD4066BMS
ANALOG INPUTS (±5V) CD4066BMS CD4054B DIGITAL CONTROL INPUTS
ANALOG OUTPUTS (±5V)
FIGURE BIDIRECTIONAL SIGNAL TRANSMISSION DIGITAL CONTROL LOGIC
Typical Performance Characteristics
CHANNEL ON-STATE RESISTANCE (RON) CHANNEL ON-STATE RESISTANCE (RON) SUPPLY VOLTAGE (VDD VEE) INPUT SIGNAL VOLTAGE (VIS) +25oC -55oC AMBIENT TEMPERATURE (TA) +125oC SUPPLY VOLTAGE (VDD VEE) -10.0 -7.5 +25oC -55oC AMBIENT TEMPERATURE (TA) +125oC
-5.0
-2.5
10.0
INPUT SIGNAL VOLTAGE (VIS)
FIGURE TYPICAL ON-STATE RESISTANCE INPUT SIGNAL VOLTAGE (ALL TYPES)
CHANNEL ON-STATE RESISTANCE (RON)
FIGURE TYPICAL ON-STATE INPUT SIGNAL VOLTAGE (ALL TYPES).
CHANNEL ON-STATE RESISTANCE (RON)
SUPPLY VOLTAGE (VDD VSS) -10.0 -7.5 -5.0 -2.5 10.0 INPUT SIGNAL VOLTAGE (VIS)
AMBIENT TEMPERATURE (TA) +25oC SUPPLY VOLTAGE (VDD VSS)
AMBIENT TEMPERATURE (TA) +125oC
+25oC -55oC
-10.0 -7.5 -5.0 -2.5 10.0 INPUT SIGNAL VOLTAGE (VIS)
FIGURE TYPICAL ON-STATE RESISTANCE INPUT SIGNAL VOLTAGE (ALL TYPES)
FIGURE ON-STATE RESISTANCE INPUT SIGNAL VOLTAGE (ALL TYPES)
7-973
CD4066BMS Typical Performance Characteristics
OUTPUT VOLTAGE (VO) AMBIENT TEMPERATURE (TA) +25oC 2.5V, -2.5V INPUT TERM OUTPUT TERM 100K
(Continued)
POWER DISSIPATION PACKAGE (PD) (µW)
AMBIENT TEMPERATURE (TA) +25oC
SUPPLY VOLTAGE (VDD)
CD4066BMS SWITCHES UNUSED TERMINALS CONNECTED
CD4066/
100K
SWITCHING FREQUENCY (kHz)
INPUT VOLTAGE (VI)
FIGURE TYPICAL CHARACTERISTICS CHANNELS
FIGURE POWER DISSIPATION PACKAGE SWITCHING FREQUENCY
Chip Dimensions Layout
Dimensions parenthesis millimeters derived from basic inch dimensions indicated. Grid graduations mils (10-3 inch).
Special Considerations applications that employ separate power sources drive signal inputs, current capability should exceed VDD/RL effective external load four CD4066B bilateral switches). This provision avoids permanent current flow clamp action supply when power applied removed from CD4066B. certain applications, external load-resistor current include both signal line components. avoid drawing current when switch current flows into terminals voltage drop across bidirectional switch must exceed volts (calculated from values shown). current will flow through switch current flows into terminals METALLIZATION: Thickness: PASSIVATION: Silane BOND PADS: 0.004 inches 0.004 inches 0.0198 inches 0.0218 inches THICKNESS:
7-974
Other recent searches
PD60234 - PD60234 PD60234 Datasheet
IR22771S - IR22771S IR22771S Datasheet
IR21771S - IR21771S IR21771S Datasheet
NTE7166 - NTE7166 NTE7166 Datasheet
MMBR911LT1 - MMBR911LT1 MMBR911LT1 Datasheet
MMBR911LT1G - MMBR911LT1G MMBR911LT1G Datasheet
EP169 - EP169 EP169 Datasheet
Bi5U-Q08-AP6X2 - Bi5U-Q08-AP6X2 Bi5U-Q08-AP6X2 Datasheet
Privacy Policy | Disclaimer
© 2012 Datasheet Archive
