Features LIN-Bus Transceiver compliant specification revision I2T
|
|
|
Top Searches for this datasheet
transceiver MTC-30600
Features
LIN-Bus Transceiver compliant specification revision I2T-100 High Voltage Technology voltage ±80V Transmission rate 20kBaud Package Protection Thermal shutdown Indefinite short-circuit protection supply ground Transients VBAT (80V) Power saving Operating voltage 5.5V Power down supply current <50µA compatibility Integrated filter hysteresis receiver compatibility Integrated slope control transmitter Slope control dependant from Vbat enable maximum capacitive-load
single-wire transceiver MTC-30600 monolithic integrated circuit SO-8 package. works interface between protocol controller physical bus. MTC-30600 especially suitable drive line systems automotive industrial applications. Further used standard ISO9141 systems. order reduce current consumption MTC-30600 offers stand-by mode. wake-up caused message sets output pulls INH-output high until device switched normal operation mode. transceiver implemented I2T-100 technology enabling both high voltage analogue circuitry digital functionality co-exist same chip. MTC-30600 provides ultra-safe solution today's automotive In-Vehicle Networking requirements providing unlimited short circuit protection event fault condition.
Ordering Information Part MTC-30600-I Package: Temp. Range: -40°C.125°C
Semiconductor www.amis.com
transceiver MTC-30600
Typical application Schematic
Application schematic
Fig.1: Typical application diagram with master slave module
Semiconductor www.amis.com
transceiver MTC-30600
description 2.2.1 (Top view)
Fig.2: configuration (viewed from above)
2.2.2 description Symbol Function Receive data output; dominant state Enable input; transceiver normal operation mode when HIGH; Internal pull supply input Transmit data input; dominant state; Internal pull Ground output/input; dominant state; Internal pull Battery supply input; Inhibit output; control voltage regulator, becomes HIGH when wake-up occurs
Semiconductor www.amis.com
transceiver MTC-30600
Application Information
after wake-up after start
Fig.3: State Diagram fail safe reasons MTC-30600 already internal pull resistor implemented. achieve required timings dominant recessive transition signal additional external termination resistor required. recommended place this resistor master node. avoid reverse currents from line into battery supply line case unpowered node, recommended place diode series external pull small systems (low capacitance) performance system supported additional capacitor least master node (see figure Typical application diagram). capacitor 10µF supply voltage input buffers input voltage. combination with required reverse polarity diode this prevents device from detecting power down conditions case negative transients supply line. order reduce current consumption MTC-30600 offers sleep operation mode. This mode selected switching enable input (see figure state diagram). sleep mode voltage regulator controlled output order minimize current consumption whole application. wake-up caused message communication automatically enables voltage regulator switching output high. parallel, wake-up indicated setting output low. When entering normal mode this wake-up flag reset output released transmit data. case voltage regulator control input connected output microcontroller active respectively, MTC-30600 normal operation mode without wake-up communication bus.
Semiconductor www.amis.com
transceiver MTC-30600
Electrical Characteristics
Absolute maximum ratings Note: Maximum ratings absolute ratings; exceeding these values cause irreversible damage integrated circuit. Parameter Voltages Supply voltage Battery supply voltage input voltage voltage Logic voltages TxD, Electrostatic discharge voltage Electrostatic discharge voltage Temperatures Junction temperature Symbol Limit Values -0.3 -0.3 -0.3 -0.3 VB+0.3 VCC+0.3 Unit Remarks
Vbus Vinh VESD VESD
human body model (100 1.5k) human body model (100 1.5k)
Semiconductor www.amis.com
transceiver MTC-30600
Operating Range Parameter Voltages Supply voltage Battery supply voltage Junction temperature Thermal Shutdown temp Thermal shutdown hyst. Thermal resistances Junction ambient Rthj-a Symbol Limit Values Unit Remarks
Thermal Shutdown (junction temperature) TjSD
Semiconductor www.amis.com
transceiver MTC-30600
Electrical Characteristics <5.5 =500 VEN,on j<125 voltages with respect ground; positive current flowing into pin; unless otherwise specified. Parameter Symbol Limit Values Unit 0.48 0.52 0.02 0.40 0.15 -200 pull resistance Enable input (pin HIGH level input voltage EN,on level input voltage EN,off Pull-down resistor Inhibit output (pin INH) HIGH level drop voltage Leakage current INH,lk 0.04 0.60 Remarks recessive state; recessive state; dominant state; dominant state; sleep-mode 0.7mA 0.7mA
Current Consumption Current consumption Current consumption Current consumption Current consumption Current consumption Receiver Output (pin RxD) HIGH level output RD,H level output receiver (pin LIN) Receiver threshold voltage, recessive dominant edge Receiver threshold voltage,dominant recessive edge Receiver hysteresis wake-up threshold voltage RD,L
bus,rd bus,dr bus,hys wake
Vbus,dom bus,rec bus,hys bus,rec Vbus,dom
Transmission Input (pin TxD) HIGH level input voltage level input voltage TD,L Pull-up resistor transmitter (pin LIN) recessive output voltage dominant output voltage dominant output voltage short circuit current Leakage current TD,pu bus,rec bus,dom bus,volt bus,sc bus,lk
recessive state dominant state
40mA bus,short 13.5 =0V, =0V, =0V, =0V,
-400
normal mode power mode
0.15 sleep mode
Semiconductor www.amis.com
transceiver MTC-30600
Electrical Characteristics (cont'd) <5.5 =500 VEN,on j<125 voltages with respect ground; positive current flowing into pin; unless otherwise specified.
Load driver definitions (between transceivers supply Load slope definitions (typical loads) (L1) (L2) 6.8nF (L3) 10nF
Parameter
Symbol
Limit Values 22,5 22,5
Unit
Remarks
Dynamic Transceiver Characteristics Slope time falling edge _slope_F Slope time rising edge _slope_R Slope time symmetry _slope _Sym Propagation delay T_tr_F Propagation delay T_tr_R HIGH Propagation delay T_rec_F dominant Propagation delay T_rec_R recessive HIGH Receiver delay sym, symmetry Transmitter delay sym,Tr symmetry Wake-up delay time wake
T_slope_Sym =t_slope_F -t_slope_R <20pF
<20pF
sym,Rec T_rec_F -T_rec_R sym,Tr T_tr_F T_tr_R
Semiconductor www.amis.com
transceiver MTC-30600
Load driver definitions (between transceivers supply Load slope definitions (typical loads) (L1) (L2) 6.8nF (L3) 10nF
Fig.4: Transmitter-parameters
Semiconductor www.amis.com
transceiver MTC-30600
Package Outlines
Sorts Packing Package outlines tubes, trays etc. contained Data Book "Package Information". Surface Mounted Device
Dimensions
Semiconductor www.amis.com
transceiver MTC-30600
Semiconductor www.amis.com
2002 Semiconductor, Inc. Semiconductor makes warranty products, other than those expressly contained company's standard warranty contained Semiconductor's Terms Conditions. company assumes responsibility errors which appear this document, reserves right change devices specifications detailed herein time without notice, does make commitment update information contained herein. licenses patents other intellectual property Semiconductor granted company connection with sale Semiconductor products, expressly implication.
Other recent searches
MAX2235 - MAX2235 MAX2235 Datasheet
KM23C64000G - KM23C64000G KM23C64000G Datasheet
G065VN01 - G065VN01 G065VN01 Datasheet
FSJ055R4 - FSJ055R4 FSJ055R4 Datasheet
AD7356 - AD7356 AD7356 Datasheet
Privacy Policy | Disclaimer
© 2012 Datasheet Archive
