Mapping Controller Operating voltage: 2.7V~5.2V Built-in oscillat

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

Mapping Controller Operating voltage: 2.7V~5.2V Built-in oscillat

Datasheet Thumbnail

Top Searches for this datasheet

HT1625
Mapping Controller
Operating voltage: 2.7V~5.2V Built-in oscillator External 32.768kHz crystal 32kHz frequency Built-in display address auto increment selectable buzzer frequencies (2kHz 4kHz) Power down command reduces power consumption Software configuration feature Data mode Command mode instructions Three data accessing modes VLCD adjust operating voltage Cascade application 100-pin package
source input
bias, duty, frame frequency 64Hz Max. patterns, commons, segments Built-in internal resistor type bias generator 3-wire serial interface kinds time base selection Time base overflow output
General Description
HT1625 peripheral device specially designed type used expand display capability. max. display segment device patterns also supports serial interface, buzzer sound, Watchdog Timer time base timer functions. HT1625 memory mapping multi-function controller. software configuration feature HT1625 make suitable multiple applications including modules display subsystems. Only three lines required interface between host controller HT1625. HT162X series have many kinds products that match various applications.
Selection Table
HT162X Built-in Osc. Crystal Osc. HT1620 HT1621 HT1622 HT16220 HT1623 HT1625 HT1626
Block Diagram
Rev. 1.10
September 2002
HT1625
Assignment
Rev. 1.10
September 2002
HT1625
Assignment
Chip size: (mil)2 substrate should connected layout artwork.
Rev. 1.10
September 2002
HT1625
Coordinates
-90.18 -90.18 -90.18 -90.18 -89.42 -89.42 -90.18 -90.18 -90.18 -90.18 -90.18 -90.18 -90.18 -90.18 -90.18 -90.18 -90.18 -90.18 -90.18 -83.17 -76.54 -69.91 -63.28 -56.65 -50.02 -43.39 -36.76 -30.13 -23.50 -16.87 -10.24 -3.61 3.02 9.65 16.28 22.91 29.54 41.52 48.15 60.14 66.77 78.75 90.57 90.57 98.56 91.93 85.30 75.95 57.76 45.77 39.14 32.51 25.03 15.94 5.82 -3.61 -10.24 -16.87 -23.50 -30.13 -36.76 -43.39 -92.22 -99.53 -99.53 -99.53 -99.53 -99.53 -99.53 -99.53 -99.53 -99.53 -99.53 -99.53 -99.53 -99.53 -99.53 -99.53 -99.53 -99.53 -98.60 -98.60 -98.60 -98.60 -98.60 -98.60 -97.79 -91.16 90.57 90.57 89.80 89.80 89.80 89.80 89.80 89.80 89.80 89.80 89.80 89.80 89.80 89.80 89.80 89.80 89.80 89.80 89.80 89.80 89.38 77.39 70.76 58.78 52.15 40.16 32.09 25.46 18.83 12.20 5.57 -1.06 -7.69 -14.32 -20.95 -27.58 -34.21 -40.84 -47.47 -54.10 -60.73 -67.36 -73.99 -84.53 -77.90 -68.13 -61.50 -49.51 -42.88 -30.90 -24.27 -12.28 -5.65 6.33 12.96 24.95 31.58 43.56 50.19 62.18 68.81 80.79 87.42 98.22 98.22 98.22 98.22 98.22 98.22 99.32 99.32 99.32 99.32 99.32 99.32 99.32 99.32 99.32 99.32 99.32 99.32 99.32 99.32 99.32 99.32 99.32 Unit:
Rev. 1.10
September 2002
HT1625
Description
Name Description READ clock input with pull-high resistor. Data HT1625 clocked falling edge signal. clocked data will appear data line. host controller next rising edge latch clocked data. WRITE clock input with pull-high resistor. Data DATA line latched into HT1625 rising edge signal. Serial data input output with pull-high resistor Negative power supply, ground OSCI OSCO pads connected 32.768kHz crystal order generate system clock. system clock comes from external clock source, external clock source should connected OSCI pad. on-chip oscillator selected instead, OSCI OSCO pads left open. Positive power supply operating voltage input pad. Time base Watchdog Timer overflow flag, NMOS open drain output 2kHz 4kHz tone frequency output pair connected common outputs segment outputs Chip selection input with pull-high resistor. When logic high, data command read from write HT1625 disabled. serial interface circuit also reset. logic level input pad, data command transmission between host controller HT1625 enabled.
DATA OSCI
OSCO
12~14 15~22 23~86
VLCD T1~T3 COM0~COM7 SEG0~SEG63
Absolute Maximum Ratings
Supply Voltage .-0.3V 5.5V Input Voltage.VSS-0.3V VDD+0.3V Storage Temperature .-50°C 125°C Operating Temperature.-25°C 75°C
Note: These stress ratings only. Stresses exceeding range specified under Maximum cause substantial damage device. Functional operation this device other conditions beyond those listed specification implied prolonged exposure extreme conditions affect device reliability.
Rev. 1.10
September 2002
HT1625
D.C. Characteristics
Symbol IDD1 IDD2 IDD11 IDD22 ISTB IOL1 IOH1 IOL1 IOH1 IOL2 IOH2 IOL3 IOH3 Parameter Operating Voltage Operating Current Test Conditions Conditions load On-chip oscillator load Crystal oscillator load On-chip oscillator load Crystal oscillator load, Power down mode Min. -0.9 -1.7 -0.9 -1.7 Typ. -1.8 -1.8 -180 -140 Max. Ta=25°C Unit
Operating Current
Operating Current
Operating Current
Standby Current
Input Voltage
DATA,
Input High Voltage
DATA, VOL=0.3V VOL=0.5V VOH=2.7V VOH=4.5V VOL=0.3V VOL=0.5V VOH=2.7V VOH=4.5V VOL=0.3V VOL=0.5V VOH=2.7V VOH=4.5V VOL=0.3V VOL=0.5V VOH=2.7V VOH=4.5V DATA,
DATA
DATA
Common Sink Current
Common Source Current
Segment Sink Current
Segment Source Current
Pull-high Resistor
Rev. 1.10
September 2002
HT1625
A.C. Characteristics
Symbol fSYS1 fSYS2 fLCD1 fLCD2 tCOM fCLK1 fCLK2 Parameter System Clock System Clock Frame Frequency Frame Frequency Common Period Serial Data Clock Pin) Test Conditions tCLK Input Pulse Width (Figure tsu1 Rise Fall Time Serial Data Clock Width (Figure Setup Time DATA Clock Width (Figure Hold Time DATA Clock Width (Figure Setup Time Clock Width (Figure Hold Time Clock Width (Figure Conditions On-chip oscillator External clock source On-chip oscillator External clock source Number Duty cycle Min. 3.34 6.67 1.67 3.34 Typ. n/fLCD Max. Ta=25°C Unit
Serial Data Clock Pin) Serial Interface Reset Pulse Width (Figure
Duty cycle Write mode Read mode Write mode Read mode
Figure
Figure
Figure
Rev. 1.10
September 2002
HT1625
Functional Description
Display memory structure static display organized into bits stores display data. contents directly mapped contents driver. Data accessed READ, WRITE READ-MODIFY-WRITE commands. following mapping from patterns. Time base Watchdog Timer time base generator share same divided (/256) counter. TIMER DIS/EN/CLR DIS/EN/CLR EN/DIS independent from each other. Once time-out occurs, will remain logic level until command issued.
external clock selected source system frequency, command turns invalid power down mode fails carried until external clock source removed. Buzzer tone output simple tone generator implemented HT1625. tone generator output pair differential driving signals which used generate single tone. Command format HT1625 configured software setting. There mode commands configure HT1625 resource transfer display data.
mapping
Timer configurations
Rev. 1.10
September 2002
HT1625
following data mode command mode Operation READ WRITE READ-MODIFY-WRITE COMMAND Name TONE TONE TONE Mode Data Data Data Command Command Code 0000-1000-X 010X-XXXX-X 0110-XXXX-X Turn-off tone output Turn-on tone output, tone frequency 4kHz Turn-on tone output, tone frequency 2kHz Function successive commands have been issued, command mode omitted. While system operating non-successive command non-successive address data mode, should previous operation mode will reset also. returns operation mode should issued first.
Timing Diagrams
READ mode (command code
READ mode (successive address reading)
Rev. 1.10
September 2002
HT1625
WRITE mode (command code
WRITE mode (successive address writing)
READ-MODIFY-WRITE mode (command code
READ-MODIFY-WRITE mode (successive address accessing)
Rev. 1.10
September 2002
HT1625
Command mode (command code
Mode (data command mode)
Rev. 1.10
September 2002
HT1625
Application Circuits
Note:
connection selected depending requirement MCU. voltage applied VLCD must lower than VDD. Adjust display, VDD=5V, VLCD=4V, VR=15kW±20%. Adjust (external Pull-high resistance) time base clock.
Instruction Summary
Name READ WRITE Command Code Function Read data from Write data Read Write data Turn both system oscillator bias generator Turn system oscillator Turn display Turn display Disable time base output Disable time-out flag output Enable time base output Enable time-out flag output Turn tone outputs Clear contents time base generator Clear contents stage System clock source, on-chip oscillator System clock source, external 32kHz clock source crystal oscillator 32.768kHz Def. A6A5A4A3A2A1A0D0D1D2D3 A6A5A4A3A2A1A0D0D1D2D3
READ-MODIFY1 A6A5A4A3A2A1A0D0D1D2D3 WRITE TIMER TIMER TONE TIMER 0000-0000-X 0000-0001-X 0000-0010-X 0000-0011-X 0000-0100-X 0000-0101-X 0000-0110-X 0000-0111-X 0000-1000-X 0000-1101-X 0000-1111-X 0001-10XX-X
(XTAL) 0001-11XX-X
Rev. 1.10
September 2002
HT1625
Name TONE TONE F128 TEST NORMAL Note: Command Code Function Tone frequency output: 4kHz Tone frequency output: 2kHz Disable output Enable output Time base clock output: time-out flag after: Time base clock output: time-out flag after: Time base clock output: time-out flag after: Time base clock output: time-out flag after: 1/2s Time base clock output: 16Hz time-out flag after: 1/4s Time base clock output: 32Hz time-out flag after: 1/8s Time base clock output: 64Hz time-out flag after: 1/16s Time base clock output: 128Hz time-out flag after: 1/32s Test mode, user use. Normal mode Def.
010X-XXXX-X 0110-XXXX-X 100X-0XXX-X 100X-1XXX-X 101X-0000-X 101X-0001-X 101X-0010-X 101X-0011-X 101X-0100-X 101X-0101-X 101X-0110-X 101X-0111-X 1110-0000-X 1110-0011-X
care A6~A0 address D3~D0 data Data/Command mode Def. Power reset default bold forms, namely mode commands. these, indicates command mode successive commands have been issued, command mode except first command will omitted. source tone frequency time base clock frequency derived from on-chip 32kHz oscillator, 32.768kHz crystal oscillator, external 32kHz clock. Calculation frequency based system frequency sources stated above. recommended that host controller should initialize HT1625 after power reset, power reset fail, which turn leads malfunctioning HT1625.
Rev. 1.10
September 2002
HT1625
Package Information
100-pin outline dimensions
Symbol
Dimensions Min. 18.80 13.90 24.80 19.90 2.50 0.10 Nom. 0.65 0.30 0.10 Max. 19.20 14.10 25.20 20.10 3.10 3.40 1.40 0.20
Rev. 1.10
September 2002
HT1625
Holtek Semiconductor Inc. (Headquarters) No.3, Creation Science-based Industrial Park, Hsinchu, Taiwan Tel: 886-3-563-1999 Fax: 886-3-563-1189 http://www.holtek.com.tw Holtek Semiconductor Inc. (Sales Office) 11F, No.576, Sec.7 Chung Hsiao Rd., Taipei, Taiwan Tel: 886-2-2782-9635 Fax: 886-2-2782-9636 Fax: 886-2-2782-7128 (International sales hotline) Holtek Semiconductor (Shanghai) Inc. Floor, Building No.889, Shan Rd., Shanghai, China Tel: 021-6485-5560 Fax: 021-6485-0313 http://www.holtek.com.cn Holtek Semiconductor (Hong Kong) Ltd. RM.711, Tower Cheung Plaza, Cheung Rd., Kowloon, Hong Kong Tel: 852-2-745-8288 Fax: 852-2-742-8657 Holmate Semiconductor, Inc. 48531 Warm Springs Boulevard, Suite 413, Fremont, 94539 Tel: 510-252-9880 Fax: 510-252-9885 http://www.holmate.com Copyright 2002 HOLTEK SEMICONDUCTOR INC. information appearing this Data Sheet believed accurate time publication. However, Holtek assumes responsibility arising from specifications described. applications mentioned herein used solely purpose illustration Holtek makes warranty representation that such applications will suitable without further modification, recommends products application that present risk human life malfunction otherwise. Holtek reserves right alter products without prior notification. most up-to-date information, please visit site http://www.holtek.com.tw.
Rev. 1.10
September 2002

Mapping Controller Operating voltage: 2.7V~5.2V Built-in oscillat

Top Searches for this datasheet

Other recent searches