91-11-26 98-02-04 98-08-10 Monica Poelking Raymond Monnin Raymond

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

91-11-26 98-02-04 98-08-10 Monica Poelking Raymond Monnin Raymond

Datasheet Thumbnail

Top Searches for this datasheet

REVISIONS DESCRIPTION figure Change terminal connections. subgroup Table Change vendor similar part number case outline Change IIL. Editorial changes throughout. Changes Table Table other changes 5962-R026-92. package CDFP4-F16. Change document current electronic format. Editorial changes throughout. Figure modified consistent with Table DATE (YR-MO-DA) 89-03-07 APPROVED Michael Frye
91-11-26 98-02-04 98-08-10
Monica Poelking Raymond Monnin Raymond Monnin
original first page this drawing been replaced.
SHEET SHEET STATUS SHEETS PMIC SHEET PREPARED Monica L.Poelking
STANDARD MICROCIRCUIT DRAWING
THIS DRAWING AVAILABLE DEPARTMENTS AGENCIES DEPARTMENT DEFENSE
CHECKED Raymond Monnin APPROVED Michael Frye
DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216
MICROCIRCUIT, DIGITAL, ECL, QUAD LINE
DRAWING APPROVAL DATE 87-11-10 REVISION LEVEL SIZE SHEET CAGE CODE
RECEIVER, MONOLITHIC SILICON
AMSC
67268
5962-87501
DSCC FORM 2233 DISTRIBUTION STATEMENT Approved public release; distribution unlimited.
5962-E449-98
SCOPE Scope. This drawing describes device requirements MIL-STD-883 compliant, non-JAN class level microcircuits accordance with MIL-PRF-38535, appendix Part Identifying Number (PIN). complete shown following example: 5962-87501
Drawing number
Device type (see 1.2.1)
Case outline (see 1.2.2)
Lead finish (see 1.2.3)
1.2.1 Device type(s). device type(s) identify circuit function follows: Device type Generic number 10H515 Circuit function Quad line receiver
1.2.2 Case outline(s). case outline(s) designated MIL-STD-1835 follows: Outline letter Descriptive designator GDIP1-T16 CDIP2-T16 GDFP2-F16 CDFP3-F16 CDFP4-F16 CQCC1-N20 Terminals Package style Dual-in-line Flat package Flat package Square chip carrier
1.2.3 Lead finish. lead finish specified MIL-PRF-38535, appendix Absolute maximum ratings. Supply voltage range (VEE) Input voltage range Storage temperature range. Lead temperature (soldering, seconds) Junction temperature (TJ) Maximum power dissipation (PD) Thermal resistance, junction-to-case (JC) Recommended operating conditions. Supply voltage range (VEE) Supply voltage range (VCC Ambient operating temperature range Minimum high level input voltage (VIH): +25C +125C -55C Maximum level input voltage (VIL). -5.46 minimum -4.94 maximum -0.02 0.02 1.98 2.02 -55C +125C -0.780 -0.650 -0.840 -1.950 -8.0 -5.2 -65C +165C +300C +165C MIL-STD-1835
STANDARD MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
SIZE
REVISION LEVEL
5962-87501
SHEET
APPLICABLE DOCUMENTS Government specification, standards, handbooks. following specification, standards, handbooks form part this drawing extent specified herein. Unless otherwise specified, issues these documents those listed issue Department Defense Index Specifications Standards (DoDISS) supplement thereto, cited solicitation. SPECIFICATION DEPARTMENT DEFENSE MIL-PRF-38535 Integrated Circuits, Manufacturing, General Specification for. STANDARDS DEPARTMENT DEFENSE MIL-STD-883 MIL-STD-973 MIL-STD-1835 HANDBOOKS DEPARTMENT DEFENSE MIL-HDBK-103 MIL-HDBK-780 List Standard Microcircuit Drawings (SMD's). Standard Microcircuit Drawings. Test Method Standard Microcircuits. Configuration Management. Interface Standard Microcircuit Case Outlines.
(Unless otherwise indicated, copies specification, standards, handbooks available from Standardization Document Order Desk, Robbins Avenue, Building Philadelphia, 19111-5094.) Order precedence. event conflict between text this drawing references cited herein, text this drawing takes precedence. Nothing this document, however, supersedes applicable laws regulations unless specific exemption been obtained. REQUIREMENTS Item requirements. individual item requirements shall accordance with MIL-PRF-38535, appendix nonJAN class level devices specified herein. Product built this drawing that produced Qualified Manufacturer Listing (QML) certified qualified manufacturer manufacturer been granted transitional certification MILPRF-38535 processed product accordance with manufacturers approved program plan qualifying activity approval accordance with MIL-PRF-38535. This flow documented Quality Management (QM) plan make modifications requirements herein. These modifications shall affect form, fit, function device. These modifications shall affect described herein. "QML" certification mark accordance with MILPRF-38535 required identify when flow option used. Design, construction, physical dimensions. design, construction, physical dimensions shall specified MIL-PRF-38535, appendix herein. 3.2.1 Case outline(s). case outline(s) shall accordance with 1.2.2 herein. 3.2.2 Terminal connections. terminal connections shall specified figure 3.2.3 Truth table(s). truth table(s) shall specified figure 3.2.4 Logic diagram(s). logic diagram(s) shall specified figure
STANDARD MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
SIZE
REVISION LEVEL
5962-87501
SHEET
3.2.5 Test circuit switching waveforms. Test circuit switching waveforms shall specified figure Electrical performance characteristics. Unless otherwise specified herein, electrical performance characteristic specified table shall apply over full ambient operating temperature range. Electrical test requirements. electrical test requirements shall subgroups specified table electrical tests each subgroup described table Marking. Marking shall accordance with MIL-PRF-38535, appendix part shall marked with listed herein. addition, manufacturer's also marked listed MIL-HDBK-103 (see herein). packages where marking entire number feasible space limitations, manufacturer option marking "5962-" device. Certificate compliance. certificate compliance shall required from manufacturer order listed approved source supply MIL-HDBK-103 (see herein). certificate compliance submitted DSCC-VA prior listing approved source supply shall affirm that manufacturer's product meets requirements MIL-PRF-38535, appendix requirements herein. Certificate conformance. certificate conformance required MIL-PRF-38535, appendix shall provided with each microcircuits delivered this drawing. Notification change. Notification change DSCC-VA shall required accordance with MIL-PRF-38535, appendix Verification review. DSCC, DSCC's agent, acquiring activity retain option review manufacturer's facility applicable required documentation. Offshore documentation shall made available onshore option reviewer.
STANDARD MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
SIZE
REVISION LEVEL
5962-87501
SHEET
TABLE Electrical performance characteristics. Conditions -55C +125C unless otherwise specified Quiescent tests High level output voltage through -5.2 Outputs terminated -0.780 -0.650 -0.840 -1.950 -1.950 -1.950 -1.010 -0.860 -1.060 -0.780 -0.650 -0.840
Test
Symbol
Group subgroups
Limits
Unit
Cases
level output voltage
-0.780 -0.650 -0.840 -1.110 -0.960 -1.160 -1.110 -0.960 -1.160 -5.46 -0.780 +25C
-1.950 -1.950 -1.950 -1.480 -1.465 -1.510 -1.480 -1.465 -1.510
7,8A,8B
-1.950 -1.950 -1.950 -1.010 -0.860 -1.060 -1.950 -1.950 -1.950
-1.580 -1.565 -1.610 -0.780 -0.650 -0.840 -1.580 -1.565 -1.610
High level threshold output voltage level threshold output voltage Power supply drain current High level input current
VOHA
VOLA
-0.650 +125C -0.840 -55C
Input leakage current
ICBO
-5.46 -5.2 -5.46 4.3.1c
-1.0 -1.5 -1.37 -1.31 -1.41 -1.25 -1.19 -1.27
Reference bias supply voltage Functional tests
footnotes table.
STANDARD MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
SIZE
REVISION LEVEL
5962-87501
SHEET
TABLE Electrical performance characteristics Continued. Conditions -55C +125C unless otherwise specified Rapid tests High level output voltage through -5.2 Outputs terminated -0.788 -0.659 -0.849 -1.950 -1.950 -1.950 -1.017 -0.868 -1.068 -0.788 -0.659 -0.849
Test
Symbol
Group subgroups
Limits
Unit
Cases
level output voltage
-0.788 -0.659 -0.849 -1.117 -0.968 -1.168 -1.117 -0.968 -1.168 -5.46 -0.788 +25C -0.659 +125C -0.849 -55C
-1.950 -1.950 -1.950 -1.482 -1.468 -1.513 -1.482 -1.468 -1.513
7,8A,8B
-1.950 -1.950 -1.950 -1.017 -0.868 -1.068 -1.950 -1.950 -1.950
-1.582 -1.568 -1.613 -0.788 -0.659 -0.849 -1.582 -1.568 -1.613
High level threshold output voltage level threshold output voltage Power supply drain current High level input current
VOHA
VOLA
Input leakage current
ICBO
-5.46 -5.2 -5.46 4.3.1c
-1.0 -1.5 -1.377 -1.317 -1.417 -1.257 -1.197 -1.277
Reference bias supply voltage Functional tests
footnotes table.
STANDARD MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
SIZE
REVISION LEVEL
5962-87501
SHEET
TABLE Electrical performance characteristics Continued. Conditions -55C +125C unless otherwise specified Rapid tests High level output voltage through -5.2 Outputs terminated -0.793 -0.665 -0.855 -1.950 -1.950 -1.950 -1.022 -0.874 -1.074 -0.793 -0.665 -0.855
Test
Symbol
Group subgroups
Limits
Unit
Case
level output voltage
-0.793 -0.665 -0.855 -1.122 -0.974 -1.174 -1.122 -0.974 -1.174 -5.46 -0.793 +25C
-1.950 -1.950 -1.950 -1.484 -1.470 -1.515 -1.484 -1.470 -1.515
-1.950 -1.950 -1.950 -1.022 -0.874 -1.074 -1.950 -1.950 -1.950
-1.584 -1.570 -1.615 -0.793 -0.665 -0.855 -1.584 -1.570 -1.615
High level threshold output voltage level threshold output voltage Power supply drain current High level input current
VOHA
VOLA
-0.665 +125C -0.855 -55C
Input leakage current
ICBO
-5.46 -5.2 -5.46 4.3.1c
-1.0 -1.5 -1.381 -1.322 -1.422 -1.261 -1.202 -1.281
Reference bias supply voltage Functional tests
footnotes table.
STANDARD MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
SIZE
REVISION LEVEL
5962-87501
SHEET
TABLE Electrical performance characteristics Continued. Conditions -55C +125C unless otherwise specified tests tTLH, tTHL -2.94 Load outputs through ground figure 0.45 0.50 0.50 0.45 0.50 0.45 1.40 1.70 1.40 1.20 1.80 1.20 Unit Group subgroups Cases Transition time Limits
Test
Symbol
Propagation delay time, input output
tPLH, tPHL, tPLL, tPHH
quiescent limits determined after device reached thermal equilibrium. This defined reading taken with device socket with LFPM +125 applicable) blowing unit transverse direction with power applied least minutes before reading taken. This method used theoretical limit establishment only. devices shall tested delta (rapid test) conditions specified herein. rapid test method equivalent method testing quiescent conditions. high level output current varies with temperature shall calculated using following formulas: VOH)/100 VOL)/100. limits, although specified minimum column, shall exceeded, magnitude, maximum value. rapid test forcing functions limits used testing. These limits determined each device type based power dissipation package type. rapid test (delta limits forcing functions skewed allowing rapid testing performed standard temperatures without addition delta T's.
STANDARD MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
SIZE
REVISION LEVEL
5962-87501
SHEET
Case outlines Terminal number connection
Terminal symbol
VCC1 AOUT BOUT
COUT DOUT VCC2 VCC1 AOUT BOUT
VCC1 AOUT BOUT
COUT DOUT VCC2
COUT DOUT VCC2
FIGURE Terminal connections.
STANDARD MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
SIZE
REVISION LEVEL
5962-87501
SHEET
Inputs Inverting High level level Irrelevant FIGURE Truth table. Noninverting
Output
FIGURE Logic diagram.
STANDARD MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
SIZE
REVISION LEVEL
5962-87501
SHEET
NOTES: Unused outputs connected ground. matched equal time delays. divider used. (test jig) Pulse generator characteristics: 1MHz, (20% 80%), duty cycle 50%. FIGURE Test circuit switching waveforms.
STANDARD MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
SIZE
REVISION LEVEL
5962-87501
SHEET
QUALITY ASSURANCE PROVISIONS Sampling inspection. Sampling inspection procedures shall accordance with MIL-PRF-38535, appendix Screening. Screening shall accordance with method 5004 MIL-STD-883, shall conducted devices prior quality conformance inspection. following additional criteria shall apply: Burn-in test, method 1015 MIL-STD-883. Test condition test circuit shall maintained manufacturer under document revision level control shall made available preparing acquiring activity upon request. test circuit shall specify inputs, outputs, biases, power dissipation, applicable, accordance with intent specified test method 1015 MIL-STD-883. +125C, minimum. Interim final electrical test parameters shall specified table herein, except interim electrical parameter tests prior burn-in optional discretion manufacturer. TABLE Electrical test requirements. MIL-STD-883 test requirements Subgroups accordance with MIL-STD-883, method 5005, table
Interim electrical parameters (method 5004) Final electrical test parameters (method 5004) Group test requirements (method 5005) Groups end-point electrical parameters (method 5005) applies subgroup
Quality conformance inspection. Quality conformance inspection shall accordance with method 5005 MIL-STD-883 including groups inspections. following additional criteria shall apply. 4.3.1 Group inspection. Tests shall specified table herein. Subgroups table method 5005 MIL-STD-883 shall omitted. Subgroups shall verify truth table specified figure herein.
STANDARD MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
SIZE
REVISION LEVEL
5962-87501
SHEET
4.3.2 Groups inspections. End-point electrical parameters shall specified table herein. Steady-state life test conditions, method 1005 MIL-STD-883. Test condition test circuit shall maintained manufacturer under document revision level control shall made available preparing acquiring activity upon request. test circuit shall specify inputs, outputs, biases, power dissipation, applicable, accordance with intent specified test method 1005 MIL-STD-883. +125C, minimum. Test duration: 1,000 hours, except permitted method 1005 MIL-STD-883.
PACKAGING Packaging requirements. requirements packaging shall accordance with MIL-PRF-38535, appendix NOTES Intended use. Microcircuits conforming this drawing intended Government microcircuit applications (original equipment), design applications, logistics purposes. Replaceability. Microcircuits covered this drawing will replace same generic device covered contractor-prepared specification drawing. Configuration control SMD's. proposed changes existing SMD's will coordinated with users record individual documents. This coordination will accomplished accordance with MIL-STD-973 using Form 1692, Engineering Change Proposal. Record users. Military industrial users shall inform Defense Supply Center Columbus when system application requires configuration control applicable SMD. DSCC will maintain record users this list will used coordination distribution changes drawings. Users drawings covering microelectronics devices (FSC 5962) should contact DSCC-VA, telephone (614) 692-0525. Comments. Comments this drawing should directed DSCC-VA, Columbus, Ohio 43216-5000, telephone (614) 692-0674. Approved sources supply. Approved sources supply listed MIL-HDBK-103. vendors listed MILHDBK-103 have agreed this drawing certificate compliance (see herein) been submitted accepted DSCC-VA.
STANDARD MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
SIZE
REVISION LEVEL
5962-87501
SHEET
STANDARD MICROCIRCUIT DRAWING BULLETIN DATE: 98-08-10 Approved sources supply 5962-87501 listed below immediate acquisition information only shall added MIL-HDBK-103 QML-38535 during next revision. MIL-HDBK-103 QML-38535 will revised include addition deletion sources. vendors listed below have agreed this drawing certificate compliance been submitted accepted DSCC-VA. This bulletin superseded next dated revision MIL-HDBK-103 QML-38535.
Standard microcircuit drawing 5962-8750101EA 5962-8750101FA 5962-87501012A 5962-8750101XA
Vendor CAGE number 0EU86 0EU86 0EU86
Vendor similar AS10H515C16/883C 10H515/BFAJC AS10H515EC20/883C AS10H515F16/883C
lead finish shown each representing hermetic package most readily available from manufacturer listed that part. desired lead finish listed contact vendor determine availability. Caution. this number item acquisition. Items acquired this number satisfy performance requirements this drawing. longer available from approved source supply.
Vendor CAGE number 0EU86
Vendor name address Austin Semiconductor Inc. 8701 Cross Park Austin, 78754-4566
information contained herein disseminated convenience only Government assumes liability whatsoever inaccuracies information bulletin.

91-11-26 98-02-04 98-08-10 Monica Poelking Raymond Monnin Raymond

Top Searches for this datasheet

Other recent searches