92-11-13 Frye 95-05-09 00-09-15 Frye Raymond Monnin

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

92-11-13 Frye 95-05-09 00-09-15 Frye Raymond Monnin

Datasheet Thumbnail

Top Searches for this datasheet

REVISIONS DESCRIPTION packages, C-2. Change military drawing format. Made changes 1.3, table 6.4, figure editorial changes throughout. vendor CAGE 34371. device type Editorial changes throughout. vendor CAGE 1ES66. Change from percent percent. Make changes table Remove vendor CAGE 32293. Changes accordance with 5962-R134-95. Drawing updated reflect current requirements. Incorporate revision Editorial changes throughout. Drawing updated current requirements. Editorial changes throughout. DATE (YR-MO-DA) 89-09-13 APPROVED Frye
92-11-13
Frye
95-05-09 00-09-15
Frye Raymond Monnin
03-02-12
Raymond Monnin
ORIGINAL FIRST PAGE THIS DRAWING BEEN REPLACED. CURRENT CAGE CODE 67268
SHEET SHEET STATUS SHEETS PMIC SHEET PREPARED Rick Officer
STANDARD MICROCIRCUIT DRAWING
THIS DRAWING AVAILABLE DEPARTMENTS AGENCIES DEPARTMENT DEFENSE
CHECKED Charles Besore APPROVED Frye DRAWING APPROVAL DATE 77-11-04
DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216 http://www.dscc.dla.mil
MICROCIRCUIT, CMOS, QUAD ANALOG SWITCH, MONOLITHIC SILICON
AMSC
REVISION LEVEL
SIZE SHEET
CAGE CODE
14933
77053
DSCC FORM 2233 DISTRIBUTION STATEMENT Approved public release; distribution unlimited.
5962-E192-03
SCOPE Scope. This drawing describes device requirements MIL-STD-883 compliant, non-JAN class level microcircuits accordance with MIL-PRF-38535, appendix Part Identifying Number (PIN). complete shown following example: 77053
Drawing number
Device type (see 1.2.1)
Case outline (see 1.2.2)
Lead finish (see 1.2.3)
1.2.1 Device types. device types identify circuit function follows: Device type Generic number DG201A HI-201 Circuit function Quad SPST analog switch Quad SPST analog switch, with dielectric isolation
1.2.2 Case outlines. case outlines designated MIL-STD-1835 follows: Outline letter Descriptive designator CQCC1-N20 GDIP1-T16 CDIP2-T16 GDFP2-F16 CDFP3-F16 CDFP4-F16 Terminals Package style Square leadless chip carrier package Dual-in-line package Flat pack Flat pack
1.2.3 Lead finish. lead finish specified MIL-PRF-38535, appendix Absolute maximum ratings. Supply voltage (between V-): Device type Device type Digital input voltage (VIN): Device type Device type Analog input voltage (VS). Current (any terminal except Device type Device type Continuous current, Device type Device type Peak current, (pulsed percent duty cycle maximum): Device type Device type Storage temperature range.
-0.3
-65°C +150°C
STANDARD MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
SIZE
REVISION LEVEL
77053
SHEET
Power dissipation (PD) Lead temperature (soldering, seconds). Thermal resistance, junction-to-case (JC) Junction temperature (TJ): Device type Device type ground: Device type Device type ground: Device type Device type Recommended operating conditions. Positive supply voltage (V+). Negative supply voltage (V-) Minimum digital high level input voltage (VIH) Maximum digital level input voltage (VIL) Ambient operating temperature range (TA) APPLICABLE DOCUMENTS
+275°C MIL-STD-1835 +150°C +175°C
+2.4 +0.8 -55°C +125°C
Government specification, standards, handbooks. following specification, standards, handbooks form part this drawing extent specified herein. Unless otherwise specified, issues these documents those listed issue Department Defense Index Specifications Standards (DoDISS) supplement thereto, cited solicitation. SPECIFICATION DEPARTMENT DEFENSE MIL-PRF-38535 Integrated Circuits, Manufacturing, General Specification for. STANDARDS DEPARTMENT DEFENSE MIL-STD-883 MIL-STD-1835 HANDBOOKS DEPARTMENT DEFENSE MIL-HDBK-103 MIL-HDBK-780 List Standard Microcircuit Drawings. Standard Microcircuit Drawings. Test Method Standard Microcircuits. Interface Standard Electronic Component Case Outlines.
(Unless otherwise indicated, copies specification, standards, handbooks available from Standardization Document Order Desk, Robbins Avenue, Building Philadelphia, 19111-5094.) Order precedence. event conflict between text this drawing references cited herein, text this drawing takes precedence. Nothing this document, however, supersedes applicable laws regulations unless specific exemption been obtained.
case derate mW/°C above +75°C. case derate mW/°C above +75°C.
STANDARD MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
SIZE
REVISION LEVEL
77053
SHEET
REQUIREMENTS Item requirements. individual item requirements shall accordance with MIL-PRF-38535, appendix non-JAN class level devices specified herein. Product built this drawing that produced Qualified Manufacturer Listing (QML) certified qualified manufacturer manufacturer been granted transitional certification MIL-PRF-38535 processed product accordance with manufacturers approved program plan qualifying activity approval accordance with MIL-PRF-38535. This flow documented Quality Management (QM) plan make modifications requirements herein. These modifications shall affect form, fit, function device. These modifications shall affect described herein. "QML" certification mark accordance with MIL-PRF-38535 required identify when flow option used. Design, construction, physical dimensions. design, construction, physical dimensions shall specified MIL-PRF-38535, appendix herein. 3.2.1 Case outlines. case outlines shall accordance with 1.2.2 herein. 3.2.2 Terminal connections. terminal connections shall specified figure Electrical performance characteristics. Unless otherwise specified herein, electrical performance characteristics specified table shall apply over full ambient operating temperature range. Electrical test requirements. electrical test requirements shall subgroups specified table electrical tests each subgroup described table Marking. Marking shall accordance with MIL-PRF-38535, appendix part shall marked with listed herein. addition, manufacturer's also marked listed MIL-HDBK-103 (see herein). packages where marking entire number feasible space limitations, manufacturer option marking "5962-" device. Certificate compliance. certificate compliance shall required from manufacturer order listed approved source supply MIL-HDBK-103 (see herein). certificate compliance submitted DSCC-VA prior listing approved source supply shall affirm that manufacturer's product meets requirements MIL-PRF-38535, appendix requirements herein. Certificate conformance. certificate conformance required MIL-PRF-38535, appendix shall provided with each microcircuits delivered this drawing. Notification change. Notification change DSCC-VA shall required accordance with MIL-PRF-38535, appendix Verification review. DSCC, DSCC's agent, acquiring activity retain option review manufacturer's facility applicable required documentation. Offshore documentation shall made available onshore option reviewer.
STANDARD MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
SIZE
REVISION LEVEL
77053
SHEET
TABLE Electrical performance characteristics. Conditions -55°C +125°C unless otherwise specified unused channels input leakage current IS(OFF) output leakage current ID(OFF)
Group subgroups ±0.5 ±0.5 Device type Limits ±100 ±100 ±200 Unit
Test
Symbol
Analog signal range Drain-source resistance
RDS(ON)
leakage current
ID(ON)
level input voltage High level input voltage level input leakage current
High level input leakage current
footnotes table.
STANDARD MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
SIZE
REVISION LEVEL
77053
SHEET
TABLE Electrical performance characteristics Continued. Conditions -55°C +125°C unless otherwise specified Switch time tOFF Positive supply current Group subgroups Device type Switch time Negative supply current IVIN Unless otherwise specified, limiting terms "min" (minimum) "max" (maximum) shall considered apply magnitudes only. Negative current shall defined conventional current flow device terminal. Guaranteed, tested, limits specified. Limits 1000 -6.5 -4.5 -1.5 -1.5 Unit
Test
Symbol
STANDARD MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
SIZE
REVISION LEVEL
77053
SHEET
Device type Case outlines Terminal number VGND
Terminal symbols VGND VREF VREF
VREF normally floating, voltage applied raise threshold voltage.
FIGURE Terminal connections.
STANDARD MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
SIZE
REVISION LEVEL
77053
SHEET
QUALITY ASSURANCE PROVISIONS Sampling inspection. Sampling inspection procedures shall accordance with MIL-PRF-38535, appendix Screening. Screening shall accordance with method 5004 MIL-STD-883, shall conducted devices prior quality conformance inspection. following additional criteria shall apply: Burn-in test, method 1015 MIL-STD-883. Test condition test circuit shall maintained manufacturer under document revision level control shall made available preparing acquiring activity upon request. test circuit shall specify inputs, outputs, biases, power dissipation, applicable, accordance with intent specified test method 1015 MIL-STD-883. +125°C, minimum. Interim final electrical test parameters shall specified table herein, except interim electrical parameter tests prior burn-in optional discretion manufacturer.
TABLE Electrical test requirements. Subgroups accordance with MIL-STD-883, method 5005, table -1*,
MIL-STD-883 test requirements
Interim electrical parameters (method 5004) Final electrical test parameters (method 5004) Group test requirements (method 5005) Groups end-point electrical parameters (method 5005) applies subgroup
Quality conformance inspection. Quality conformance inspection shall accordance with method 5005 MIL-STD-883 including groups inspections. following additional criteria shall apply. 4.3.1 Group inspection. Tests shall specified table herein. Subgroups table method 5005 MIL-STD-883 shall omitted.
STANDARD MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
SIZE
REVISION LEVEL
77053
SHEET
4.3.2 Groups inspections. End-point electrical parameters shall specified table herein. Steady-state life test conditions, method 1005 MIL-STD-883. Test condition test circuit shall maintained manufacturer under document revision level control shall made available preparing acquiring activity upon request. test circuit shall specify inputs, outputs, biases, power dissipation, applicable, accordance with intent specified test method 1005 MIL-STD-883. +125°C, minimum. Test duration: 1,000 hours, except permitted method 1005 MIL-STD-883.
PACKAGING Packaging requirements. requirements packaging shall accordance with MIL-PRF-38535, appendix NOTES Intended use. Microcircuits conforming this drawing intended Government microcircuit applications (original equipment), design applications, logistics purposes. Replaceability. Microcircuits covered this drawing will replace same generic device covered contractor-prepared specification drawing. Configuration control SMD's. proposed changes existing SMD's will coordinated with users record individual documents. This coordination will accomplished using Form 1692, Engineering Change Proposal. Record users. Military industrial users shall inform Defense Supply Center Columbus when system application requires configuration control applicable SMD. DSCC will maintain record users this list will used coordination distribution changes drawings. Users drawings covering microelectronics devices (FSC 5962) should contact DSCC-VA, telephone (614) 692-0544. Comments. Comments this drawing should directed DSCC-VA, Columbus, Ohio 43216-5000, telephone (614) 692-0547. Approved sources supply. Approved sources supply listed MIL-HDBK-103. vendors listed MIL-HDBK103 have agreed this drawing certificate compliance (see herein) been submitted accepted DSCCVA.
STANDARD MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
SIZE
REVISION LEVEL
77053
SHEET
STANDARD MICROCIRCUIT DRAWING BULLETIN DATE: 03-02-12 Approved sources supply 77053 listed below immediate acquisition information only shall added MIL-HDBK-103 QML-38535 during next revision. MIL-HDBK-103 QML-38535 will revised include addition deletion sources. vendors listed below have agreed this drawing certificate compliance been submitted accepted DSCC-VA. This bulletin superseded next dated revision MIL-HDBK-103 QML-38535.
Standard microcircuit drawing 77053012A 77053012C 7705301EA 7705301FA 7705301XA 7705301XC 77053022A 77053022C 7705302EA
Vendor CAGE number 17856 1ES66 17856 1ES66 17856 1ES66 34371 1ES66 1ES66
Vendor similar DG201AAZ/883 DG201AAZ/883B DG201AAK/883 DG201AAK/883B
Similar military specification
M38510/12302BEA
DG201AAL/883 DG201AAL/883B HI4-201/883 HI4-201/883B HI1-201/883B HI1-201/883
lead finish shown each representing hermetic package most readily available from manufacturer listed that part. desired lead finish listed contact vendor determine availability. Caution. this number item acquisition. Items acquired this number satisfy performance requirements this drawing. available from approved source.
Vendor CAGE number 1ES66
Vendor name address Maxim Integrated Products Gabriel Drive Sunnyvale, 94086-5125 Siliconix Incorporated 2201 Laurelwood Road Santa Clara, 95054-1516 Intersil Corporation 2401 Palm Blvd. P.O. Melbourne, 32901-0883
17856
34371
information contained herein disseminated convenience only Government assumes liability whatsoever inaccuracies information bulletin.

92-11-13 Frye 95-05-09 00-09-15 Frye Raymond Monnin

Top Searches for this datasheet

Other recent searches