Combo-D Subminiature-D Connectors Photo Unavailable Sig
|
|
|
Top Searches for this datasheet
Positronic Industries
Combo-D
Subminiature-D Connectors
Photo Unavailable
Signal, Power, Coaxial High Voltage Contacts single package
Maximum Torque Values 4-40 Threads
TORQUE MATERIAL Phos. Bronze Brass Aluminum Nylon 0.90 0.68 0.45 0.11 in-lb in-oz
These torque values applicable threads only apply hardware assemblies. These torque values approximate should accepted accurate limits. Indeterminant factors specific applications preclude publication accurate torque values universal use. Unless specified otherwise, dimensional tolerances are: ±0.001 inches (0.03 male contact mating diameters. ±0.003 inches (0.08 contact termination diameters. ±0.005 inches (0.13 other diameters. ±0.015 inches (0.38 other dimensions.
CATALOG NUMBER: C-004 REV. PUBLISHED UNITED STATES AMERICA Positronic Industries believes data contained herein reliable. Since technical information given free charge, user employs such information discretion risk. Positronic Industries assumes responsibility results obtained damages incurred from such information whole part.
Positronic Industries' FEDERAL SUPPLY CODE MANUFACTURERS number 28198.
TABLE CONTENTS
COMBINATION CONTACT SUB-D CONNECTORS SERIES CONNECTORS.1
Series (Industrial quality, 807-2, Performance Level Two) Series (Military quality DESC 85039). Fixed signal contacts size ampere nominal rating. Size power contacts through ampere nominal rating. Size shielded high voltage contacts. Solder printed board mount contact terminations available both size size contacts. Twenty connector variants, through 46W4.
SIZE REMOVABLE CONTACTS
Power, shielded high voltage. Crimp solder terminations. Functional CBD, Series connector bodies.
SERIES CONNECTORS
Series. Size crimp removable signal contacts size crimp removable power shielded contacts. connector variants, shell size through Military Industrial quality connectors conforming MIL-DTL-24308, DESC 85039 807-3, Performance Levels where applicable.
COMBINATION CONTACT DUAL PORT CONNECTORS
CBDP Series. Offers fifteen different combinations power signal contact stacked assemblies. Size signal contacts, ampere nominal rating, size power contacts, ampere maximum rating printed board mounting. ampere rating with solder crimp contacts.
DESC CROSS REFERENCE.34
Combo-D Series
INDUSTRIAL MILITARY QUALITY SUBMINIATURE-D CONNECTORS
MILITARY SHELTERED INDOOR/OUTDOOR ENVIRONMENTAL APPLICATIONS
Size Fixed Signal Contacts Size Removable Power, Shielded High Voltage Contacts Military/Industrial Quality Connectors U.L. Recognized Recognized File #E49351 File #LR54219 D.E.S.C. 85039 Telecommunication U.L. File #E140980
Combo-D Series connectors permit mixed contact combinations power, shielded, high voltage signal contacts within same connector body. Twenty connector variants offered standard shell sizes. performance levels Combo-D Series connectors offered. Series connectors professional quality connectors recommended sheltered, noncorrosive indoor outdoor environments having normal ventilation, without temperature humidity controls. Series connectors military quality connectors recommended sheltered, mildly corrosive environments having wide range temperature, pressure humidity changes. These connectors will meet applicable performance dimensional requirements 807-2, Performance Level Two, D.E.S.C. 85039. Combo-D Series connectors utilize precision machined signal contacts. Connector variants available with contact terminations solder straight printed board mount terminations featuring choice inch metric printed board footprints. Power, shielded high voltage contacts removable, having solder straight printed board mount terminations. Power shielded contacts available with crimp terminations. level shielding requirements, ferrite inductors attached both signal power contacts connectors having contact terminations which straight angled printed board mounting applications. Additional details obtained from factory Applications Engineering Department. female power contacts feature Large Surface Area (L.S.A.) closed entry contact design which provides maximum mating surfaces between male female contacts reduced contact resistance during operation. wide assortment printed board mounting hardware, cable support hoods, locking systems available from stock. blind mating system available applications requiring connector coupling recessed areas mobile power coupling systems.
SERIES CONTACT VARIANTS
FACE VIEW MALE REAR VIEW FEMALE
SHELL SIZE
SHELL SIZE
11W1
SHELL SIZE
13W3
17W2
21W1
SHELL SIZE
13W6
17W5
21WA4
25W3
27W2
SHELL SIZE
24W7
36W4
43W2
47W1
SHELL SIZE
Positronic Industries, Inc.
46W4
Series
Insulator: Signal Contacts:
INDUSTRIAL MILITARY QUALITY SUBMINIATURE-D CONNECTORS
MILITARY SHELTERED INDOOR/OUTDOOR ENVIRONMENTAL APPLICATIONS
COMBO-D SERIES TECHNICAL CHARACTERISTICS
MATERIALS FINISHES:
Glass filled polyester MIL-M-24519 94V-0, blue color, composite. Male contacts-precision machined brass alloy. Female contacts-precision machined high tensile phosphor bronze. Gold flash over nickel plate gold 0.000050 (1.25 microns) over nickel plate. Machined high conductivity copper alloy both male female contacts. Gold flash over nickel. Male contacts-precision machined brass. Female contacts-precision machined high tensile phosphor bronze.
MECHANICAL CHARACTERISTICS:
Signal Contacts, Fixed: Size contacts, male contact-0.040 inch (1.02mm) diameter. Series open entry design female contacts. Series closed entry design female contacts.
Signal Contact Plating: Power Contacts: Power Contact Plating: Shielded High Voltage Contacts:
Contact Retention Insulator:
Shielded High Voltage Contact Plating: Signal contact-gold flash over nickel. Shells: Steel brass with plate; zinc plate with dichromate seal, stainless steel passivated. Mounting Spacers Brackets: Nylon plastic, brass with plate; zinc plate with dichromate seal. Push-On Fasteners: Phosphor bronze beryllium copper with plate. Jackscrew Systems: Steel with zinc plate dichromate seal, clear zinc plate. Hoods: Composite plastic, 94V-0, brass steel with zinc plate dichromate seal.
Signal-9 lbs. (40N). Power, shielded high voltage-22 (98N). Resistance Solder Iron Heat: 500°F (260°C) seconds duration 512-6. Signal Contact Terminations: Solder contacts 0.042 inch (1.06mm) minimum hole diameter (0.5 mm2) wire maximum. Straight Printed Board Mount 0.028 inch (0.71mm) diameter. Printed Board Mount 0.028 inch (0.71 diameter. Size contact, male contact 0.142 inch (3.61mm) diameter. Female contact features Large Surface Area (L.S.A.) closed entry contact design utilizing BeCu mechanical retention member. Male female contacts have terminations wire sizes AWG. Size contact, male contact 0.142 inch (3.61mm) diameter. Printed board terminations with 0.078 inch (1.98mm), 0.093 inch (2.36mm) 0.125 inch (3.18mm) diameters. table maximum cable sizes contact termination dimensions. Straight terminations 0.041 inch (1.04mm) minimum hole diameter. Male shells dimpled EMI/ESD ground paths. Trapezoidally shaped shells polarized jackscrews. Jackscrews riveted fasteners with 0.120 inch (3.05mm) diameter hole, threaded riveted fasteners with 4-40 threads nylon inserts. Rapid installation push-on fasteners threaded posts. Jackscrews. Series, operations, Series, 1,000 operations 512-5. -55°C +125°C. days.
Power Contacts, Removable, Crimp Solder Termination:
Power Contacts, Printed Board Mount:
ELECTRICAL CHARACTERISTICS:
SIGNAL CONTACTS
Contact Current Rating: amperes nominal. Initial Contact Resistance: 0.008 ohms maximum. Proof Voltage: 1000 r.m.s. Shielded Contacts, Removable: High Voltage Contacts: Shells: Polarization: Mounting Angle Brackets:
POWER CONTACTS
Contact Current Rating: amperes nominal. Initial Contact Resistance: 0.005 ohms maximum. Proof Voltage: 1000 r.m.s.
SHIELDED CONTACTS
Initial Contact Resistance: 0.008 ohms maximum. Nominal Impedance: ohms. Insertion Loss: -0.46 -1.5 VSWR: 1.15 average 1.56 average Above values measured using frequency domain techniques. Proof Voltage: 1000 r.m.s. HIGH VOLTAGE CONTACTS Flash over Voltage: 3600 r.m.s. Proof Voltage: 2700 r.m.s. Initial Contact Resistance: 0.008 ohms maximum. CONNECTOR Insulator Resistance: ohms. Clearance Creepage Distance: 0.039 inch (1.0mm) minimum. Working Voltage: r.m.s.
Mounting Printed Board: Locking Systems: Mechanical Operations, Signal Contacts:
CLIMATIC CHARACTERISTICS:
Temperature Range: Damp Heat, Steady State:
Positronic Industries, Inc.
Series
INDUSTRIAL MILITARY QUALITY SUBMINIATURE-D CONNECTORS
MILITARY SHELTERED INDOOR/OUTDOOR ENVIRONMENTAL APPLICATIONS
CBD3W3M00000
CBD5W5M00000
STANDARD SHELL ASSEMBLY
Typ. 0.050 (1.27) ±0.010
0.036 (0.91) ±0.008
0.220 (5.59) Max.
0.120 (3.05) ±0.005 Mounting hole, places
0.120 (3.05) ±0.010
0.120 (3.05) ±0.005 Mounting hole, places 0.154 (3.91) Mounting hole available
0.032 (0.81) Total diametral float
0.086 (2.18) ±0.005 -0.000 Mounting hole, places
OPTIONAL SHELL ASSEMBLY
SHELL SIZES SHELL SIZE MALE SHELL SIZE FEMALE SHELL SIZE MALE SHELL SIZE FEMALE SHELL SIZE MALE SHELL SIZE FEMALE SHELL SIZE MALE SHELL SIZE FEMALE SHELL SIZE MALE SHELL SIZE FEMALE SHELL SIZE MALE SHELL SIZE FEMALE ±0.015 1.213 (30.81) 1.213 (30.81) 1.541 (39.14) 1.541 (39.14) 2.088 (53.04) 2.088 (53.04) 2.729 (69.32) 2.729 (69.32) 2.635 (66.93) 2.635 (66.93) 2.729 (69.32) 2.729 (69.32) ±0.005 ±0.005 0.666 (16.92) 0.643 (16.33) 0.994 (25.25) 0.971 (24.66) 1.534 (38.96) 1.511 (38.38) 2.182 (55.42) 2.159 (54.84) 2.079 (52.81) 2.064 (52.43) 2.212 (56.18) 2.189 (55.60) ±0.005 0.984 (24.99) 0.984 (24.99) 1.312 (33.32) 1.312 (33.32) 1.852 (47.04) 1.852 (47.04) 2.500 (63.50) 2.500 (63.50) 2.406 (61.11) 2.406 (61.11) 2.500 (63.50) 2.500 (63.50) ±0.005
OPTIONAL SHELL ASSEMBLY WITH UNIVERSAL FLOAT MOUNTS
±0.005 0.329 (8.36) 0.311 (7.90) 0.329 (8.36) 0.311 (7.90) 0.329 (8.36) 0.311 (7.90) 0.329 (8.36) 0.311 (7.90) 0.441 (11.20) 0.423 (10.74) 0.503 (12.78) 0.485 (12.32) ±0.015 0.494 (12.55) 0.494 (12.55) 0.494 (12.55) 0.494 (12.55) 0.494 (12.55) 0.494 (12.55) 0.494 (12.55) 0.494 (12.55) 0.605 (15.37) 0.605 (15.37) 0.668 (16.97) 0.668 (16.97) ±0.010 0.759 (19.28) 0.759 (19.28) 1.083 (27.51) 1.083 (27.51) 1.625 (41.28) 1.625 (41.28) 2.272 (57.71) 2.272 (57.71) 2.178 (55.32) 2.178 (55.32) 2.302 (58.47) 2.302 (58.47) ±0.010 0.422 (10.72) 0.422 (10.72) 0.422 (10.72) 0.422 (10.72) 0.422 (10.72) 0.422 (10.72) 0.422 (10.72) 0.422 (10.72) 0.534 (13.56) 0.534 (13.56) 0.596 (15.14) 0.596 (15.14) ±0.005 0.233 (5.92) 0.243 (6.17) 0.233 (5.92) 0.243 (6.17) 0.230 (5.84) 0.243 (6.17) 0.230 (5.84) 0.243 (6.17) 0.230 (5.84) 0.243 (6.17) 0.230 (5.84) 0.243 (6.17) ±0.010 0.422 (10.72) 0.429 (10.90) 0.422 (10.72) 0.429 (10.90) 0.426 (10.82) 0.429 (10.90) 0.426 (10.82) 0.429 (10.90) 0.426 (10.82) 0.429 (10.90) 0.426 (10.82) 0.429 (10.90)
Positronic Industries, Inc.
DIMENSIONS INCHES (MILLIMETERS) DIMENSIONS SUBJECT CHANGE
Series
INDUSTRIAL MILITARY QUALITY SUBMINIATURE-D CONNECTORS
MILITARY SHELTERED INDOOR/OUTDOOR ENVIRONMENTAL APPLICATIONS
SOLDER CONNECTOR
max. (0.5 mm2)
Fixed female jackscrews
Fixed female jackscrew
Fixed male jackscrew
0.125 (3.18)
0.345 (8.76)
solder contacts, specify code step ordering information.
Fixed male female polarized jackscrews available. Specify code step ordering information. Typical part number: CBD7W2M200T60
Typical part number: CBD7W2M200T0
STRAIGHT PRINTED BOARD MOUNT CONNECTOR
CODE NUMBER
Swaged spacer with push-on fastener, phosphor bronze. 0.010 Min. (0.25)
Fixed female jackscrews
-0.078 (1.98) 0.093 (2.36) 0.125 (3.18)
0.170 (4.32)
0.250 (6.35) 0.028 (0.71) Typical part number: CBD17W2F35S60T2X
straight printed board mount contacts, specify code step ordering information.
DIMENSIONS INCHES (MILLIMETERS) DIMENSIONS SUBJECT CHANGE
CBD17W2F200E0 with FS4008D contacts.
CBD17W2M55B30T20
Positronic Industries, Inc.
Series
INDUSTRIAL MILITARY QUALITY SUBMINIATURE-D CONNECTORS
MILITARY SHELTERED INDOOR/OUTDOOR ENVIRONMENTAL APPLICATIONS
PRINTED BOARD MOUNTED POWER CONTACTS
STRAIGHT PRINTED BOARD MOUNT POWER CONTACTS
Straight printed board mount power contacts mounted connector when ordered.
FEMALE CLOSED ENTRY, L.S.A.
0.142 (3.61)
MALE
0.170 (4.32)
0.626 (15.90)
0.634 (16.10)
PART NUMBER FDS4314D FDS4312D FDS4310D
0.078 (1.98) 0.094 (2.39) 0.125 (3.18)
CURRENT RATING Amps. Amps. Amps.
PART NUMBER MDS4314D MDS4312D MDS4310D
0.078 (1.98) 0.094 (2.39) 0.125 (3.18)
CURRENT RATING Amps. Amps. Amps.
Material High conductivity copper alloy. Plating Gold flash over nickel.
PRINTED BOARD MOUNT POWER CONTACTS
printed board mount power contacts mounted connector when ordered.
0.142 (3.61)
FEMALE
CLOSED ENTRY, L.S.A.
MALE
PART CURRENT REF. NUMBER FRT4314D FRT4414D FRT4714D FRT4814D FRT4310D FRT4410D Amps Amps Amps Amps Amps Amps 0.580 (14.73) 0.692 (17.58) 0.661 (16.79) 0.773 (19.63) 1.051 (26.70) 1.051 (26.70)
0.078 (1.98) 0.078 (1.98) 0.078 (1.98) 0.078 (1.98) 0.125 (3.18) 0.125 (3.18)
0.339 (8.61) 0.451 (11.46)
SHELL SIZE
BEND CODE
PART CURRENT REF. NUMBER MRT4314D MRT4414D MRT4714D MRT4814D MRT4310D MRT4410D
Note:
0.078 (1.98) 0.078 (1.98) 0.078 (1.98) 0.078 (1.98) 0.125 (3.18) 0.125 (3.18)
0.339 (8.61) 0.451 (11.46)
SHELL SIZE
BEND CODE
Amps Amps Amps Amps Amps Amps
0.580 (14.73) 0.692 (17.58) 0.661 (16.79) 0.773 (19.63) 1.051 (26.70) 1.051 (26.70)
0.420 (10.67) 0.520 (13.21)
0.420 (10.67) 0.520 (13.21)
0.810 (20.57) 0.810 (20.57)
0.810 (20.57) 0.810 (20.57)
Material High conductivity copper alloy. Plating Gold flash over nickel. DIMENSIONS INCHES (MILLIMETERS) DIMENSIONS SUBJECT CHANGE
Female power contacts feature Large Surface Area (L.S.A.) closed entry contact design which provides maximum mating surfaces between male female contacts reduced contact resistance during operation.
Positronic Industries, Inc.
Series
0.220 (5.59) Max.
INDUSTRIAL MILITARY QUALITY SUBMINIATURE-D CONNECTORS
MILITARY SHELTERED INDOOR/OUTDOOR ENVIRONMENTAL APPLICATIONS
PRINTED BOARD MOUNT CONNECTOR WITH 0.125 (3.18) POWER CONTACTS
CODE 0.283 (7.19) CONTACT EXTENSION
amps nominal) CBD00R7000 0.283 (7.19) CONTACT EXTENSION SHELL SIZE SHELL SIZE 1.204 (30.58) 1.532 (38.91) 2.072 (52.63) 2.720 (69.09) 2.626 (66.70) 0.984 (24.99) 1.312 (33.32) 1.852 (47.04) 2.500 (63.50) 2.406 (61.11) 0.339 (8.61) 0.339 (8.61) 0.339 (8.61) 0.339 (8.61) 0.395 (10.03) 0.283 (7.19) 0.283 (7.19) 0.283 (7.19) 0.283 (7.19) 0.283 (7.19) 0.120 (3.05) PLASTIC MOUNTING BRACKET AVAILABLE Specify code step ordering information. 0.060 (1.52) 0.090 (2.29) 0.123 (3.12) 0.240 (6.10)
Fixed female jackscrews
SHELL SIZE ±0.008 SHELL SIZE SHELL SIZE SHELL SIZE
0.149 (3.78)
0.810 (20.57)
Specify code step ordering information.
0.810 (20.57) 0.112 (2.84) Typ. Numbering shown rear view male face view female.
0.112 (2.84) Typ. 0.112 (2.84) Typ.
Typical part number: CBD17W2M57R7NT20
Push-on fastener, 0.170 (4.32) beryllium copper. Nominal
0.125 (3.18) 0.028 (0.71) Typical part number: CBD36W4F57R7NT2X
0.220 (5.59) Max.
PRINTED BOARD MOUNT CONNECTOR WITH 0.078 (1.98) POWER CONTACTS
CODE 0.283 (7.19) CONTACT EXTENSION
amps nominal) CBD00R7000 0.283 (7.19) CONTACT EXTENSION SHELL SIZE SHELL SIZE ±0.008 SHELL SIZE SHELL SIZE SHELL SIZE SHELL SIZE 0.339 (8.61) 0.112 (2.84) Typ. Numbering shown rear view male face view female. 1.204 (30.58) 1.532 (38.91) 2.072 (52.63) 2.720 (69.09) 2.626 (66.70) 0.984 (24.99) 1.312 (33.32) 1.852 (47.04) 2.500 (63.50) 2.406 (61.11) 0.339 (8.61) 0.339 (8.61) 0.339 (8.61) 0.339 (8.61) 0.395 (10.03) 0.283 (7.19) 0.283 (7.19) 0.283 (7.19) 0.283 (7.19) 0.283 (7.19) 0.112 (2.84) Typ. 0.112 (2.84) Typ. 0.149 (3.78) 0.451 (11.46) PLASTIC MOUNTING BRACKET AVAILABLE Specify code step ordering information. 0.060 (1.52) 0.240 (6.10)
Fixed female jackscrews
0.090 (2.29) 0.120 (3.05) 0.123 (3.12)
Specify code step ordering information.
Typical part number: CBD17W2M55R7NT20 DIMENSIONS INCHES (MILLIMETERS) DIMENSIONS SUBJECT CHANGE
Push-on fastener, beryllium copper. 0.170 (4.32) Nominal
0.078 (1.98) 0.028 (0.71)
Typical part number: CBD36W4F55R7NT2X
Positronic Industries, Inc.
Series
0.125 (3.18) Typ. 0.220 (5.59) Max.
INDUSTRIAL MILITARY QUALITY SUBMINIATURE-D CONNECTORS
MILITARY SHELTERED INDOOR/OUTDOOR ENVIRONMENTAL APPLICATIONS
METRIC SYSTEM PRINTED BOARD MOUNT CONNECTOR WITH 0.078 (1.98) POWER CONTACTS
CODE 0.370 (9.40) CONTACT EXTENSION
amps nominal) PLASTIC MOUNTING BRACKET AVAILABLE Specify code step ordering information. 0.060 (1.52) 0.090 (2.29) 0.120 (3.05) 0.123 (3.12) 0.240 (6.10)
CBD00R7000 0.370 (9.40) CONTACT EXTENSION SHELL SIZE SHELL SIZE SHELL SIZE SHELL SIZE SHELL SIZE SHELL SIZE 1.204 (30.58) 1.532 (38.91) 2.072 (52.63) 2.720 (69.09) 2.626 (66.70) 0.984 (24.99) 1.312 (33.32) 1.852 (47.04) 2.500 (63.50) 2.406 (61.11) 0.420 (10.67) 0.420 (10.67) 0.420 (10.67) 0.420 (10.67) 0.470 (11.94) 0.370 (9.40) 0.370 (9.40) 0.370 (9.40) 0.370 (9.40) 0.370 (9.40)
±0.008 Fixed female jackscrews
0.149 (3.78)
0.100 (2.54) Typ. 0.100 (2.54) Typ. Specify code step ordering information. 0.420 (10.67) 0.100 (2.54) Typ. Numbering shown rear view male face view female.
0.520 (13.21)
Typical part number: CBD17W2M75R70T20
0.170 (4.32) Nominal 0.024 (0.61)
0.078 (1.98)
Typical part number: CBD36W4M75R70T20
0.125 (3.18) Typ. 0.220 (5.59) Max.
METRIC SYSTEM PRINTED BOARD MOUNT CONNECTOR WITH 0.125 (3.18) POWER CONTACTS
CODE 0.370 (9.40) CONTACT EXTENSION
amps nominal) CBD00R7000 0.370 (9,40) CONTACT EXTENSION SHELL SIZE SHELL SIZE 1.204 (30.58) 1.532 (38.91) 2.072 (52.63) 2.720 (69.09) 2.626 (66.70) 0.984 (24.99) 1.312 (33.32) 1.852 (47.04) 2.500 (63.50) 2.406 (61.11) 0.420 (10.67) 0.420 (10.67) 0.420 (10.67) 0.420 (10.67) 0.470 (11.94) 0.370 (9.40) 0.370 (9.40) 0.370 (9.40) 0.370 (9.40) 0.370 (9.40) PLASTIC MOUNTING BRACKET AVAILABLE Specify code step ordering information. 0.060 (1.52) 0.240 (6.10) 0.090 (2.29) 0.120 (3.05) 0.123 (3.12)
Fixed female jackscrews
±0.008
SHELL SIZE SHELL SIZE SHELL SIZE SHELL SIZE
0.149 (3.78)
0.810 (20.57)
0.100 (2.54) Typ. Numbering shown rear view male face view female. 0.100 (2.54) Typ. 0.100 (2.54) Typ.
Specify code step ordering information.
0.810 (20.57)
Typical part number: CBD17W2M77R70T20
0.170 (4.32) Nominal
0.125 (3.18) 0.024 (0.61) Typical part number: CBD36W4M77R70T20 DIMENSIONS INCHES (MILLIMETERS) DIMENSIONS SUBJECT CHANGE
Positronic Industries, Inc.
Series
INDUSTRIAL MILITARY QUALITY SUBMINIATURE-D CONNECTORS
MILITARY SHELTERED INDOOR/OUTDOOR ENVIRONMENTAL APPLICATIONS
SHELL SIZE PRINTED BOARD MOUNT CONNECTOR WITH 0.078 (1.98) POWER CONTACTS
CODE 0.283 (7.19) CONTACT EXTENSION
CONNECTOR VARIANT 46W4 amps nominal) Fixed female jackscrews
0.451(11.46)
Shell size connector
±0.008 2.500 (63.50)
0.507(12.88) 0.283(7.19)-Specify code step ordering information 0.112(2.84) Typ.
2.720 (69.09)
Numbering shown rear view male face view female
Typical part number: CBD46W4M55R7NT20
0.170(4.32) Nominal
Push-on fastener, beryllium copper
0.078(1.98) 0.028(0.71)
SHELL SIZE PRINTED BOARD MOUNT CONNECTOR WITH 0.125 (3.18) POWER CONTACTS
CODE 0.283 (7.19) CONTACT EXTENSION
CONNECTOR VARIANT 46W4 amps nominal) Fixed female jackscrews
0.451(11.46)
Shell size connector
±0.008 2.500 (63.50)
0.810 (20.57) 0.283(7.19)-Specify code step ordering information 0.112(2.84) Typ.
2.720 (69.09)
Numbering shown rear view male face view female
Typical part number: CBD46W4M57R7NT20
0.170(4.32) Nominal
Push-on fastener, beryllium copper
0.125(3.18) 0.028(0.71)
DIMENSIONS INCHES (MILLIMETERS) DIMENSIONS SUBJECT CHANGE
Positronic Industries, Inc.
Series
INDUSTRIAL MILITARY QUALITY SUBMINIATURE-D CONNECTORS
MILITARY SHELTERED INDOOR/OUTDOOR ENVIRONMENTAL APPLICATIONS
STRAIGHT PRINTED BOARD CONTACT HOLE PATTERN WITH 0.078 (1.98) 0.094 (2.39) 0.125 (3.18) POWER CONTACTS
Hole identification shown male connector, mirror image female connector. Mount connector with mating face positioned follow direction arrow.
0.218 (5.54) TYP. 0.162 (4.11) TYP. 0.270 (6.86) TYP. 0.270 (6.86) TYP. 0.054 (1.37) TYP. 0.108 (2.74) TYP. 0.162 (4.11) TYP.
0.492 (12.50) TYP.
0.656 (16.66) TYP.
0.108 (2.74) TYP. 0.656 (16.66) TYP.
0.268 (6.81) TYP. 0.034 (0.86)
0.108 (2.74) TYP. 0.216 (5.49) 0.162 (4.11)
0.216 (5.49) TYP. 0.656 (16.66) TYP.
0.108 (2.74) TYP. 0.054 (1.37) TYP.
11W1
0.570 (14.48) TYP. 0.926 (23.52) TYP.
0.109 (2.77) TYP. 0.218 (5.54) TYP.
0.306 (7.77) 0.570 (14.48) TYP. 0.926 (23.52) TYP.
0.306 (7.77) 0.570 (14.48) TYP. 0.926 (23.52) TYP.
0.650 (16.51) 0.250 (6.35) TYP. 0.150 (3.81)
13W3
0.109 (2.77) TYP.
0.054 (1.37) TYP. 0.544 (13.82) TYP. 0.926 (23.52) TYP.
0.163 (4.14) TYP. 0.926 (23.52) TYP.
21W1
0.275 (6.99) TYP. 0.343 (8.71) 0.109 (2.77) TYP. 0.893 (22.68) TYP. 0.618 (15.70) TYP. 0.109 (2.77) TYP.
0.600 (15.24) 0.900 (22.86) TYP. 1.250 (31.75) TYP.
17W2
0.707 (17.96) 0.109 (2.77) TYP. 0.652 (16.56)
0.092 (2.34) 0.265 (6.73) TYP. 1.250 (31.75) TYP.
0.055 (1.40) TYP. 0.618 (15.70) 1.250 (31.75) TYP.
0.055 (1.40) TYP. 1.250 (31.75) TYP.
13W6
17W5
0.893 (22.68) TYP. 0.109 (2.77) TYP.
21WA4
0.893 (22.68) TYP. 0.109 (2.77) TYP.
0.270 (6.86) TYP.
0.055 (1.40) TYP. 0.618 (15.70) 1.250 (31.75) TYP.
0.055 (1.40) TYP. 1.250 (31.75) TYP.
0.109 (2.77) TYP. 1.203 (30.56) TYP.
DIMENSIONS INCHES (MILLIMETERS) DIMENSIONS SUBJECT CHANGE
25W3
0.810 (20.57) TYP. 0.055 (1.40) TYP. 0.109 (2.77) TYP.
27W2
0.810 (20.57) 0.540 (13.72) 0.109 (2.77) TYP.
24W7
CODE
0.112 (2.84) 0.056 (1.42) 0.100 (2.54) 0.050 (1.27)
0.112 (2.84) 0.056 (1.42) 0.112 (2.84) 0.056 (1.42)
0.100 (2.54) 0.050 (1.27) 0.100 (2.54) 0.050 (1.27)
0.270 (6.86) 0.540 (13.72) 1.203 (30.56) TYP.
0.055 (1.40) TYP. 1.203 (30.56) TYP.
36W4
0.900 (22.86) TYP. 0.650 (16.51) TYP.
43W2
0.810 (20.57) 0.109 (2.77) TYP. PLACES
0.060 (1.52) TYP. TYP. 0.120 (3.05) TYP. PLACES 1.250 (31.75) TYP.
0.055 (1.40) TYP. 1.203 (30.56) TYP.
47W1
46W4
Positronic Industries, Inc.
Suggest Suggest Suggest Suggest Suggest
0.045 (1.14) hole signal contact termination positions. 0.098 (2.49) hole 0.078 (1.98) power contact termination positions. 0.114 (2.90) hole 0.094 (2.39) power contact termination positions. 0.145 (3.68) hole 0.125 (3.18) power contact termination positions. 0.123 ±0.003 (3.12) hole mounting connector with push-on fasteners.
Series
INDUSTRIAL MILITARY QUALITY SUBMINIATURE-D CONNECTORS
MILITARY SHELTERED INDOOR/OUTDOOR ENVIRONMENTAL APPLICATIONS
PRINTED BOARD CONTACT HOLE PATTERN WITH 0.125 (3.18) POWER CONTACTS
Hole identification shown male connector, mirror image female connector. Mount connector with mating face positioned follow direction arrow.
0.218 (5.54) TYP. 0.162 (4.11) TYP. 0.270 (6.86) TYP. 0.270 (6.86) TYP. 0.054 (1.37) TYP. 0.108 (2.74) PLACES. 0.162 (4.11) TYP.
0.492 (12.50) TYP.
0.656 (16.66) TYP.
0.268 (6.81) TYP. PLACES 0.034 (0.86)
0.108 (2.74) TYP. PLACES 0.216 (5.49) 0.162 (4.11)
0.108 (2.74) TYP. PLACES 0.656 (16.66) TYP.
0.216 (5.49) TYP. 0.656 (16.66) TYP.
0.108 (2.74) TYP. PLACES 0.054 (1.37) TYP.
11W1
0.570 (14.48) TYP. 0.926 (23.52) TYP.
0.109 (2.77) TYP. PLACES 0.109 (2.77) TYP. PLACES 0.218 (5.54) TYP.
0.306 (7.77) 0.570 (14.48) TYP. 0.926 (23.52) TYP. 0.650 (16.51) 0.250 (6.35) TYP. PLACES 0.150 (3.81)
13W3
0.306 (7.77) 0.570 (14.48) TYP. 0.926 (23.52) TYP.
0.054 (1.37) TYP. 0.544 (13.82) TYP. 0.926 (23.52) TYP.
0.163 (4.14) TYP. 0.926 (23.52) TYP.
0.600 (15.24) 0.900 (22.86) TYP. 1.250 (31.75) TYP.
21W1
0.893 (22.68) TYP. 0.618 (15.70) TYP. 0.109 (2.77) TYP. PLACES
17W2
0.707 (17.96) 0.109 (2.77) TYP. PLACES 0.652 (16.56) 0.275 (6.99) TYP. PLACES 0.343 (8.71) 0.109 (2.77) TYP. PLACES
0.092 (2.34) 0.265 (6.73) TYP. PLACES 1.250 (31.75) TYP.
0.055 (1.40) TYP. 0.618 (15.70) 1.250 (31.75) TYP.
0.055 (1.40) TYP. 1.250 (31.75) TYP.
21WA4
13W6
0.893 (22.68) TYP. 0.109 (2.77) TYP. PLACES
17W5
0.893 (22.68) TYP. 0.109 (2.77) TYP. PLACES 0.270 (6.86) TYP. PLACES
0.055 (1.40) TYP. 0.618 (15.70) 1.250 (31.75) TYP.
0.055 (1.40) TYP. 1.250 (31.75) TYP.
0.109 (2.77) TYP. PLACES 1.203 (30.56) TYP.
27W2
0.810 (20.57) 0.540 (13.72) 0.109 (2.77) TYP. PLACES
DIMENSIONS INCHES (MILLIMETERS) DIMENSIONS SUBJECT CHANGE
25W3
24W7
0.810 (20.57) TYP. 0.055 (1.40) TYP. 0.109 (2.77) TYP. PLACES
0.270 (6.86) 0.540 (13.72) 1.203 (30.56) TYP.
0.055 (1.40) TYP. 1.203 (30.56) TYP.
36W4 CODE 0.359 (9.12) 0.290 (7.37) 0.112 (2.84) 0.100 (2.54) 0.056 (1.42) 0.050 (1.27)
0.060 (1.52) TYP. TYP. 0.900 (22.86) TYP. 0.650 (16.51) TYP.
43W2
0.810 (20.57) 0.109 (2.77) TYP. PLACES
0.471 0.415 (11.96) (10.54) 0.390 (9.91) 0.340 (8.64)
0.055 (1.40) TYP. 1.203 (30.56) TYP.
0.120 (3.05) TYP. PLACES 1.250 (31.75) TYP.
46W4 Suggest 0.045 (1.14) hole signal contact termination positions. Suggest 0.145 (3.68) hole power contact termination positions. Suggest 0.123±0.003 (3.12) hole mounting connector with push-on fasteners.
47W1
Positronic Industries, Inc.
Series
INDUSTRIAL MILITARY QUALITY SUBMINIATURE-D CONNECTORS
MILITARY SHELTERED INDOOR/OUTDOOR ENVIRONMENTAL APPLICATIONS
PRINTED BOARD MOUNTED SHIELDED CONTACTS
STRAIGHT PRINTED BOARD MOUNT SHIELDED CONTACTS
Straight printed board mount shielded contacts mounted connector when ordered.
0.156 (3.96) 0.200 (5.08)
0.040 (1.02)
0.156 (3.96) 0.200 (5.08) 0.152 (3.86)
Suggest 0.045 (1.14) hole 0.200 (5.08)
0.037 (0.94) Across points
FEMALE
MALE
PART FDS4201D
0.481 (12.22)
0.025 (0.64)
0.181 (4.60)
PART MDS4201D
0.489 (12.42)
0.025 (0.64)
0.181 (4.60)
0.100 (2.54) FDS4201D MDS4201D Contact hole pattern Material Copper alloy with PTFE teflon insulator. Signal contact plating -0.000030 inch (0.75µ) gold over nickel 0.000050 inch (1.25µ) gold over nickel. Contact body plating -Gold flash over nickel. *Technical characteristics listed page
PRINTED BOARD MOUNT SHIELDED CONTACTS
printed board mount shielded contacts mounted connector when ordered.
FEMALE
0.162 (4.11) Suggest 0.045 (1.14) hole 0.037 (0.94) Across points 0.200 (5.08) PART FRT4201D 0.100 (2.54) FRT4201D MRT4201D Contact hole pattern Material Copper alloy with PTFE teflon insulator. Signal contact plating -0.000030 inch (0.75µ) gold over nickel 0.000050 inch (1.25µ) gold over nickel. Contact body plating -Gold flash over nickel. *Technical characteristics listed page 0.040 (1.02)
MALE
0.162 (4.11) 0.152 (3.86)
0.827 (21.01)
0.240 (6.10)
0.259 (6.58)
0.470 (11.94)
PART MRT4201D
0.829 (21.06)
0.240 (6.10)
0.253 (6.43)
0.470 (11.94)
DIMENSIONS INCHES (MILLIMETERS) DIMENSIONS SUBJECT CHANGE
Positronic Industries, Inc.
Series
INDUSTRIAL MILITARY QUALITY SUBMINIATURE-D CONNECTORS
MILITARY SHELTERED INDOOR/OUTDOOR ENVIRONMENTAL APPLICATIONS
STRAIGHT PRINTED BOARD MOUNT CONNECTOR WITH SHIELDED CONTACTS
CODE CONNECTOR WITH FDS4201D MDS4201D CONTACTS
Fixed female jackscrews
0.250 (6.35)
0.170 (4.32)
0.028 (0.71)
Push-on fastener, phosphor bronze 0.156 (3.96) 0.025 (0.64) 0.028 (0.71) Numbering shown rear view male face view female.
0.037 (0.94) Across points Typical part number: CBD17W2M65S60T20
PRINTED BOARD MOUNT CONNECTOR WITH SHIELDED CONTACTS
CODE CONNECTOR WITH FRT4201D MRT4201D CONTACTS
CBD00850000 0.283 (7.19) CONTACT EXTENSION SHELL SIZE SHELL SIZE Fixed female jackscrews SHELL SIZE SHELL SIZE SHELL SIZE SHELL SIZE 1.204 (30.58) 1.532 (38.91) 2.072 (52.63) 2.720 (69.09) 2.620 (66.70) 0.984 (24.99) 1.312 (33.32) 1.852 (47.04) 2.500 (63.50) 2.406 (61.11) 0.339 (8.61) 0.339 (8.61) 0.339 (8.61) 0.339 (8.61) 0.395 (10.03) 0.283 (7.19) 0.283 (7.19) 0.283 (7.19) 0.283 (7.19) 0.545 (13.84)
±0.008
Numbering shown rear view male face view female. 0.156 (3.96) 0.170 (4.32) Nominal specify code step ordering information 0.028 (0.71) place, 0.037 (0.94) Across points places 0.470 (11.94) 0.112 (2.84) Typ. specify code step ordering information
0.112 (2.84) Typ. 0.470 (11.94) Push-on fastener, beryllium copper 0.028 (0.71)
Typical part number: CBD17W2M85R7NT20
Typical part number: CBD36W4M85R7NT20 Note: Shell size connectors supplied inverted when ordered with printed board mount shielded contacts.
DIMENSIONS INCHES (MILLIMETERS) DIMENSIONS SUBJECT CHANGE
Positronic Industries, Inc.
Series
INDUSTRIAL MILITARY QUALITY SUBMINIATURE-D CONNECTORS
MILITARY SHELTERED INDOOR/OUTDOOR ENVIRONMENTAL APPLICATIONS
STRAIGHT PRINTED BOARD MOUNT CONTACT HOLE PATTERN WITH FDS4201D MDS4201D SHIELDED CONTACTS
Hole identification shown male connector, mirror image female connector.
0.218 (5.54) Typ. 0.162 (4.11) Typ. 0.200 (5.08) 0.100 (2.54) 0.056 (1.42) 0.492 (12.50) Typ.
0.108 (2.74) Typ. 0.270 (6.86) Typ. 0.112 (2.84) 0.100 (2.54) 0.054 (1.37) Typ.
0.200 (5.08) 0.200 (5.08)
0.112 (2.84)
0.200 (5.08)
0.108 (2.74) Typ. 0.162 0.112 (2.84) (4.11) Typ. 0.056 (1.42) 0.216 (5.49) Typ. 0.656 (16.66) Typ.
0.100 0.656 (16.66) Typ. (2.54)
0.268 (6.81) Typ. 0.034 (0.86) 0.200 (5.08) 0.100 (2.54) 0.570 Typ. 0.100 (14.48) (2.54) 0.926 (23.52) Typ.
0.216 (5.49) 0.162 (4.11) 0.200 (5.08) 0.108 (2.74) Typ.
0.056 (1.42) 0.100 0.270 (6.86) Typ. (2.54) 0.656 (16.66) Typ.
0.108 (2.74) Typ. 0.200 (5.08) 0.112 (2.84) 0.054 (1.37) Typ.
11W1
0.109 (2.77) Typ. 0.054 (1.37) Typ. 0.112 (2.84) 0.056 (1.42) 0.544 (13.82) Typ. 0.926 (23.52) Typ.
0.272 (6.91) Typ. 0.218 (5.54) Typ. 0.200 (5.08) 0.100 (2.54) 0.056 (1.42) 0.100 0.163 (4.14) (2.54) 0.926 (23.52) Typ. 0.109 (2.77) Typ. 0.112 (2.84) 0.200 (5.08)
0.056 (1.42) 0.306 (7.77) 0.570 (14.48) Typ. 0.926 (23.52) Typ.
0.650 (16.51) 0.150 (3.81)
0.100 (2.54) 0.306 (7.77) 0.570 (14.48) Typ. 0.926 (23.52) Typ.
17W2
0.109 (2.77) Typ.
13W3
0.250 (6.35) Typ. 0.200 (5.08) 0.707 (17.96) 0.652 (16.56) 0.112 (2.84)
0.100 (2.54) 0.600 (15.24) 0.900 (22.86) Typ. 1.250 (31.75) Typ.
21W1
0.343 (8.71) 0.200 (5.08) 0.109 (2.77) Typ. 0.275 (6.99) Typ. 0.112 (2.84)
0.056 (1.42) 0.092 (2.34) 0.265 (6.73) Typ. 1.250 (31.75) Typ.
0.109 (2.77) Typ. 0.055 (1.40) Typ. 0.200 (5.08)
13W6
0.109 (2.77) Typ. 0.055 (1.40) Typ. 0.112 (2.84)
0.100 (2.54)
17W5
0.200 (5.08) 0.109 (2.77) Typ. 0.055 (1.40) Typ.
0.056 (1.42) 0.055 (1.40) Typ. 0.618 (15.70) 1.250 (31.75) Typ.
Typ. 0.100 0.618 (15.70) (2.54) 0.893 (22.68) Typ. 1.250 (31.75) Typ.
21WA4
0.112 (2.84) 0.270 (6.86) Typ. 0.112 (2.84) 0.200 (5.08) 0.100 (2.54)
25W3
0.109 (2.77) Typ. 0.055 (1.40) Typ.
0.618 (15.70) 0.056 (1.42) 0.893 (22.68) Typ. 1.205 (31.75) Typ. 0.810 (20.57) Typ. 0.224 (5.69)
0.100 (2.54)
0.056 (1.42) 0.893 (22.68) Typ. 1.250 (31.75) Typ.
0.056 (1.42) 0.109 (2.77) Typ. 1.203 (30.56) Typ.
27W2
0.224 (5.69) 0.810 (20.57) 0.540 (13.72) 0.200 (5.08) 0.100 (2.54)
24W7
0.810 (20.57) 0.055 (1.40) Typ. 0.200 (5.08) 0.100 (2.54)
36W4
0.120 (3.05) Typ. 0.060 (1.52) Typ.
0.112 0.270 (6.86) (2.84) 0.540 (13.72) 1.203 (30.56) Typ.
0.100 (2.54) Typ.
0.112 (2.84)
0.056 0.055 (1.42) (1.40) Typ. 0.109 (2.77) Typ. 1.203 (30.56) Typ.
0.112 (2.84) 0.224 (5.69)
0.109 0.056 (2.77) Typ. (1.42) 1.203 (30.56) Typ.
0.650 (16.51) Typ.
0.050 (1.27)
43W2
47W1
0.900 (22.86) Typ. 1.250 (31.75) Typ.
46W4
Suggest 0.045 (1.14) hole signal contact termination position. Suggest 0.123±0.003 (3.12) hole mounting connector with push-on fasteners.
DIMENSIONS INCHES (MILLIMETERS) DIMENSIONS SUBJECT CHANGE
Positronic Industries, Inc.
Series
INDUSTRIAL MILITARY QUALITY SUBMINIATURE-D CONNECTORS
MILITARY SHELTERED INDOOR/OUTDOOR ENVIRONMENTAL APPLICATIONS
PRINTED BOARD MOUNT CONTACT HOLE PATTERN WITH FRT4201D MRT4201D SHIELDED CONTACTS
Hole identification shown male connector, mirror image female connector. Mount connector with mating face positioned follow direction arrow.
0.218 (5.54) Typ. 0.162 (4.11) Typ. 0.200 (5.08) 0.100 (2.54) 0.131 (3.33) 0.100 0.056 (1.42) (2.54) 0.492 (12.50) Typ. 0.131 (3.33) 0.112 (2.84) 0.270 (6.86) Typ.
0.200 (5.08)
0.200 (5.08) 0.054 (1.37) Typ.
0.108 (2.74) Typ. 0.112 (2.84)
0.200 (5.08) 0.162 (4.11) Typ.
0.108 (2.74) Typ. 0.112 (2.84)
0.268 (6.81) Typ. 0.034 (0.86) 0.200 (5.08) 0.131 (3.33)
0.216 (5.49) 0.162 (4.11)
0.100 (2.54) 0.656 (16.66) Typ. 0.131 (3.33)
0.056 (1.42) 0.270 (6.86) Typ. 0.656 (16.66) Typ.
0.100 (2.54)
0.056 (1.42) 0.216 (5.49) Typ. 0.656 (16.66) Typ.
0.108 (2.74) Typ. 0.108 (2.74) Typ. 0.112 (2.84) 0.054 (1.37) Typ.
0.131 (3.33) 0.200 (5.08) 0.131 (3.33)
11W1
0.109 (2.77) Typ. 0.112 (2.84)
0.054 (1.37) Typ.
0.100 (2.54) 0.570 (14.48) Typ. 0.926 (23.52) Typ.
0.056 (1.42) 0.306 (7.77) 0.570 (14.48) Typ. 0.926 (23.52) Typ.
0.109 (2.77) Typ. 0.218 (5.54) Typ. 0.200 (5.08) 0.100 (2.54) 0.131 (3.33) 0.100 (2.54) 0.200 (5.08) 0.112 (2.84)
0.100 (2.54) 0.306 (7.77) 0.570 (14.48) Typ. 0.926 (23.52) Typ.
0.056 (1.42) 0.544 (13.82) Typ. 0.926 (23.52) Typ.
0.650 (16.51) 0.150 (3.81)
13W3
0.250 (6.35) Typ. 0.200 (5.08) 0.707 (17.96) 0.652 (16.56)
17W2
0.109 (2.77) Typ. 0.112 (2.84)
0.056 (1.42) 0.163 (4.14) Typ. 0.926 (23.52) Typ.
0.131 (3.33)
0.600 (15.24) 0.900 (22.86) Typ. 1.250 (31.75) Typ.
0.100 (2.54) 0.131 (3.33)
0.056 (1.42) 0.092 (2.34) 0.265 (6.73) Typ. 1.250 (31.75) Typ.
21W1
0.343 (8.71) 0.109 (2.77) Typ. 0.200 (5.08) 0.100 (2.54) 0.131 (3.33) 0.056 (1.42) 0.055 (1.40) Typ. 0.618 (15.70) 1.250 (31.75) Typ. 0.275 (6.99) Typ. 0.112 (2.84)
0.109 (2.77) Typ. 0.055 (1.40) Typ.
0.100 (2.54) 0.200 (5.08)
13W6
0.109 (2.77) Typ. 0.055 (1.40) Typ. 0.112 (2.84)
0.131 (3.33) 0.618 (15.70) Typ. 0.893 (22.68) Typ. 1.250 (31.75) Typ.
0.056 (1.42) 0.618 (15.70) 0.893 (22.68) Typ. 1.250 (31.75) Typ.
17W5
0.109 (2.77) Typ. 0.055 (1.40) Typ. 0.200 (5.08) 0.100 (2.54) 0.131 (3.33) 0.893 (22.68) Typ. 0.056 (1.42) 0.112 (2.84) 0.374 (9.50)
21WA4
0.109 (2.77) Typ. 0.200 (5.08) 0.100 (2.54)
25W3
0.109 (2.77) Typ. 0.055 (1.40) Typ. 0.374 (9.50)
1.250 (31.75) Typ.
27W2
0.109 (2.77) Typ. 0.100 (2.54) 0.055 (1.40) Typ. 0.112 (2.84) 0.112 (2.84)
0.075 0.270 (1.91) (6.86) Typ. 1.203 (30.56) Typ.
0.270 (6.86) 0.540 (13.72) 0.810 (20.57) Typ. 1.203 (30.56) Typ.
24W7
0.109 (2.77) Typ. 0.055 (1.40) Typ.
36W4
0.112 (2.84) 0.112 (2.84)
0.100 (2.54)
0.200 (5.08) 0.075 (1.91)
0.540 (13.72) 0.810 (20.57)
0.150 (3.81) 0.200 (5.08) 0.075 (1.91)
0.810 (20.57)
0.150 (3.81)
1.203 (30.56) Typ.
1.203 (30.56) Typ.
47W1
43W2
Suggest 0.045 (1.14) hole signal contact termination positions. Suggest 0.123±0.003 (3.12) hole mounting connector with push-on fasteners. Note: Shell size connectors supplied inverted when ordered with printed board mount shielded contacts. DIMENSIONS INCHES (MILLIMETERS) DIMENSIONS SUBJECT CHANGE
Positronic Industries, Inc.
Series
INDUSTRIAL MILITARY QUALITY SUBMINIATURE-D CONNECTORS
MILITARY SHELTERED INDOOR/OUTDOOR ENVIRONMENTAL APPLICATIONS
ORDERING INFORMATION CODE NUMBERING SYSTEM
Specify Complete Connector Following Steps Through Insert When Step Used
STEP
17W2
STEP Basic Series
Industrial Quality with Open Entry Signal Contacts Military Conformance with "Closed Entry" Signal Contacts
**STEP Special Options
759.0 Blind Mate Pilot 759.1 Blind Mate Panel
STEP Shell Options
Zinc Plated with Dichromate Seal Stainless Steel Plated Plated Dimpled
STEP Combo-D Series Connector Variants
Shell Size Shell Size 3W3, 7W2, 11W1 Shell Size 5W5, 9W4, 13W3, 17W2, 21W1 Shell Size 8W8, 13W6, 17W5, 21WA4, 25W3, 27W2 Shell Size 24W7, 36W4, 43W2, 47W1 Shell Size 46W4
*STEP Locking Polarizing Systems
None Fixed Female Jackscrews Fixed Female Jackscrews Rotating Male Jackscrews
*STEP Hoods Push-On Fasteners
None Hood, Side Opening, robust extended height, plastic composite, with rotating male jackscrews, shell sizes through Hood, Opening, Metal, shell sizes through Hood, EMI/RFI, Metal, shell sizes through Push-on Fastener, Mounting Brackets
STEP Connector Gender
Male Female
*STEP Mounting Style STEP Type Contacts
Connector ordered without size power shielded high voltage removable contacts. pages contact part numbers. Solder, Signal Contacts only. Solder, Straight Printed Board Mount with Signal Contacts, 0.170 (4.32) Tail Length. Solder, Straight Printed Board Mount with Signal 0.078 (1.98) Power Contacts, 0.170 (4.32) Tail Length. Solder, Straight Printed Board Mount with Signal 0.094 (2.39) Power Contacts, 0.170 (4.32) Tail Length. Solder, Straight Printed Board Mount with Signal 0.125 (3.18) Power Contacts, 0.170 (4.32) Tail Length. Solder, Printed Board Mount with Signal Contacts only, 0.283 (7.19) Signal Contact Extension. Solder, Printed Board Mount with Signal 0.078 (1.98) Power Contacts, 0.283 (7.19) Signal Contact Extension. Solder, Printed Board Mount with Signal 0.125 (3.18) Power Contacts, 0.283 (7.19) Signal Contact Extension. Solder, Straight Printed Board Mount with Signal Shielded Contacts MDS/FDS 4201D footprint, 0.170 (4.32) Signal Contact Tail Length. Solder, Metric System Printed Board Mount with Signal Contacts only, 0.370 (9.40) Signal Contact Extension. Solder, Metric System Printed Board Mount with Signal 0.078 (1.98) Power Contacts, 0.370 (9.40) Signal Contact Extension. Solder, Metric System Printed Board Mount with Signal 0.125 (3.18) Power Contacts, 0.370 (9.40) Signal Contact Extension. Solder, Printed Board Mount with Signal Shielded Contacts MRT/FRT 4201D footprint, 0.283 (7.19) Signal Contact Extension. Mounting Hole, 0.120 (3.05) Bracket, Mounting, Metal with Cross Bracket, Mounting, Plastic with Cross Float Mounts, Universal Threaded Post, Brass, 0.250 (6.35) Length Threaded Post, Nylon, 0.250 (6.35) Length Bracket, Mounting, Metal, Swaged Connector with 4-40 Thread Fixed Female Jackscrews with Cross Bracket, Mounting, Metal, Swaged Connector with 0.120 (3.05) Mounting Hole with Cross Bracket, Mounting, Metal, Swaged Connector with 4-40 Threads with Cross Bracket, Mounting, Metal, Swaged Connector with 4-40 Locknut with Cross Swaged Spacer, 4-40 Threads, 0.250 (6.35) Length Swaged Spacer, 4-40 Threads, 0.125 (3.18) Length Swaged Locknut, 4-40 Threads Swaged Spacer with Push-on Fastener, 4-40 Threads, 0.250 (6.35) Length
*For additional information accessories listed steps Accessory Catalog. Hood recommended with series shell sizes through ***Not available shell size 46W4.
Positronic Industries, Inc.
Series
SIZE REMOVABLE CONTACTS, POWER, SHIELDED HIGH VOLTAGE REMOVABLE POWER CONTACTS
SOLDER POWER CONTACTS *FEMALE
CLOSED ENTRY, L.S.A. 0.142 (3.61)
MALE
0.402 (10.21) Solder power contacts supplied kitted with connector ordered separately. PART NUMBER FS4008D FS4012D FS4016D CURRENT RATING Amps Amps Amps WIRE SIZE REF. 0.858 (21.79) 0.858 (21.79) 0.858 (21.79) 0.219 (5.56) 0.143 (3.63) 0.100 (2.54) 0.188 (4.78) 0.112 (2.84) 0.069 (1.75) PART NUMBER MS4008D MS4012D MS4016D CURRENT RATING Amps Amps Amps WIRE SIZE REF. 0.868 (22.05) 0.868 (22.05) 0.868 (22.05) 0.219 (5.56) 0.143 (3.63) 0.100 (2.54) 0.188 (4.78) 0.112 (2.84) 0.069 (1.75)
Material High conductivity copper alloy.
Plating Gold flash over nickel.
REMOVABLE CRIMP CONTACTS
Crimp power contacts supplied kitted with connector ordered separately. *FEMALE CONTACT CLOSED ENTRY, L.S.A.
POWER CONTACTS
MALE CONTACT
0.142 (3.61) 0.354 (8.99)
0.354 (8.99)
Material High conductivity copper alloy. Plating Gold flash over nickel. WIRE SIZE 0.882 (22.40) 0.882 (22.40) 0.882 (22.40) 0.882 (22.40) 0.181 (4.60) 0.122 (3.10) 0.101 (2.57) 0.067 (1.70) MAX. 0.640 (16.26) 0.640 (16.26) 0.640 (16.26) 0.640 (16.26)
PART NUMBER FC4008D FC4010D FC4012D FC4016D
CURRENT RATING Amps Amps Amps Amps
WIRE SIZE
0.858 (21.79) 0.858 (21.79) 0.858 (21.79) 0.858 (21.79)
0.181 (4.60) 0.122 (3.10) 0.101 (2.57) 0.067 (1.70)
MAX. 0.640 (16.26) 0.640 (16.26) 0.640 (16.26) 0.640 (16.26)
PART NUMBER MC4008D MC4010D MC4012D MC4016D
CURRENT RATING Amps Amps Amps Amps
*Note: Female contacts feature Large Surface Area (L.S.A.) closed entry contact design which provides maximum mating surfaces between male female contact reduced contact resistance during operation.
4311-0-0 Power Contact Removal Tool
REELS AUTOMATIC FEED PNEUMATIC CRIMP TOOLS
9509-0-0 Power Contact Hand Crimp Tool with *C4010D, *C4012D *C4016D Contacts 9504-19-0 Power Contact Hand Crimp Tool with *C4008D Contacts (tool shown)
DIMENSIONS INCHES (MILLIMETERS) DIMENSIONS SUBJECT CHANGE Contacts supplied plastic carriers, packaged reels holding 1,000 contacts with automatic feed pneumatic crimp tools, catalog part number 9555-10. same type carrier used both male female contacts. male female crimp contacts ordered reels adding letter after contact part number, such MC4008DR male contact FC4008DR female contact.
Positronic Industries, Inc.
Series
SIZE REMOVABLE CONTACTS, POWER, SHIELDED HIGH VOLTAGE
SHIELDED CONTACTS TECHNICAL CHARACTERISTICS
MATERIALS FINISHES:
Insulating Material: Inner Contacts: (Dielectric) PTFE, Teflon Brass Phosphor bronze, 0.000030 inch (0.8 microns) gold over nickel 0.000050 inch (1.25µ) gold over nickel. Brass Phosphor bronze, gold flash over nickel.
MECHANICAL CHARACTERISTICS:
Removable Contacts: Durability: Vibration: Shock: Rear insertion, front release. cycles minimum. from 30g-11
Contact Body:
CLIMATIC CHARACTERISTICS:
Temperature Range: -55°C +125°C.
ELECTRICAL CHARACTERISTICS:
Initial Contact Resistance: 0.008 ohms maximum. ohms. Nominal Impedance: Insertion Loss: -0.46 -1.5 VSWR: 1.15 average 1.56 average Proof Voltage: 1000 r.m.s.
Above values measured using frequency domain techniques.
Positronic Industries, Inc.
Series
SIZE REMOVABLE CONTACTS, POWER, SHIELDED HIGH VOLTAGE
REMOVABLE SHIELDED CONTACTS
Shielded contacts supplied kitted with connector ordered separately.
STRAIGHT SOLDER/CRIMP CONTACTS
FEMALE CONTACT
0.040 (1.02)
0.152 (3.86)
MALE CONTACT
STRAIGHT SOLDER/SOLDER CONTACTS
FEMALE CONTACT
0.040 (1.02)
0.152 (3.86)
MALE CONTACT
STRAIGHT CRIMP/CRIMP CONTACTS
FEMALE CONTACT
0.040 (1.02)
0.152 (3.86)
MALE CONTACT
Material- Copper alloy with PTFE teflon insulator.
Signal contact plating- 0.000030 inch (0.75µ) gold over nickel 0.000050 inch (1.25µ) gold over nickel. Contact body plating- Gold flash over nickel.
TYPE CONTACT SOLDER/CRIMP SOLDER/CRIMP SOLDER/CRIMP SOLDER/CRIMP SOLDER/SOLDER SOLDER/SOLDER SOLDER/SOLDER SOLDER/SOLDER CRIMP/CRIMP CRIMP/CRIMP CRIMP/CRIMP CRIMP/CRIMP
PART NUMBER MALE MC4101D MC4102D MC4103D MC4104D MS4101D MS4102D MS4103D MS4104D MCC4101D MCC4102D MCC4103D MCC4104D FEMALE FC4101D FC4102D FC4103D FC4104D FS4101D FS4102D FS4103D FS4104D FCC4101D FCC4102D FCC4103D FCC4104D
0.929 (23.60) 0.929 (23.60) 1.037 (26.34) 1.037 (26.34) 0.929 (23.60) 0.929 (23.60) 1.037 (26.34) 1.037 (26.34) 0.929 (23.60) 0.929 (23.60) 1.037 (26.34) 1.037 (26.34)
0.040 (1.02) 0.067 (1.70) 0.108 (2.74) 0.120 (3.05) 0.040 (1.02) 0.067 (1.70) 0.108 (2.74) 0.120 (3.05) 0.040 (1.02) 0.067 (1.70) 0.108 (2.74) 0.120 (3.05)
MAX. 0.739 (18.77) 0.739 (18.77) 0.847 (21.51) 0.847 (21.51) 0.739 (18.77) 0.739 (18.77) 0.847 (21.51) 0.847 (21.51) 0.739 (18.77) 0.739 (18.77) 0.847 (21.51) 0.847 (21.51)
CABLE NUMBER DIMENSIONS INCHES (MILLIMETERS) DIMENSIONS SUBJECT CHANGE page crimp tool crimping information. Two-step crimping action signal shielding conductors.
Positronic Industries, Inc.
Series
SIZE REMOVABLE CONTACTS, POWER, SHIELDED HIGH VOLTAGE
SOLDERING CRIMPING INFORMATION COMBINATION SERIES COAXIAL CONTACTS
STEP STRIP WIRE INDICATED LENGTH
PART NUMBER C4101D S4101D
CABLE NUMBER
0.281 (7.14) 0.281 (7.14) 0.375 (9.53) 0.375 (9.53) 0.281 (7.14) 0.281 (7.14) 0.375 (9.53) 0.375 (9.53)
0.250 (6.35) 0.250 (6.35) 0.312 (7.92) 0.312 (7.92) 0.250 (6.35) 0.250 (6.35) 0.312 (7.92) 0.312 (7.92)
0.078 (1.98) 0.078 (1.98) 0.078 (1.98) 0.078 (1.98) 0.120 (3.05) 0.120 (3.05) 0.120 (3.05) 0.120 (3.05)
CRIMP TOOL 9504-0 NONE 9504-0 NONE 9504-0 NONE 9504-0 NONE 9504-14 9504-13 9504-15 9504-15
Insulation Braid Dielectric Center conductor
C4102D S4102D C4103D S4103D C4104D S4104D CC4101D CC4102D
TAKE CARE -Damage remove strands. -Untwist overtwist strands. -Leave insulation particles strands. -Damage insulation.
CC4103D CC4104D
STEP SOLDER WIRE CONTACT
-Trim cable. center conductor. -Slide ferrule over jacket. Insert dielectric center conductor into barrel. Solder center conductor into contact. -Butt ferrule against shoulder. Solder cable barrel through hole ferrule. Solder into body.
Contact gender designated male contacts female contacts.
Ferrule Solder crimp
STEP SOLDER/CRIMP WIRE CONTACT
Jacket -Trim cable. center conductor. -Slide ferrule over jacket. Insert dielectric center conductor into barrel. Solder center conductor into contact. -Butt ferrule against shoulder. Crimp ferrule over braid. Solder into body. Barrel Ferrule Solder
STEP CRIMP WIRE CONTACT
-Trim cable. -Slide ferrule over jacket. Insert dielectric center conductor into barrel. Crimp center conductor into contact. -Butt ferrule against shoulder. Crimp ferrule over braid. Jacket Barrel
Shielded Contact Hand Crimp Tool
Chart Above Crimp Tool Part Numbers.
Positronic Industries, Inc.
Series
SIZE REMOVABLE CONTACTS, POWER, SHIELDED HIGH VOLTAGE
REMOVABLE HIGH VOLTAGE CONTACTS
High voltage contacts supplied with connectors must ordered separately.
STRAIGHT SOLDER WIRE TERMINATION
Max. 0.734 (18.64) Ref. 0.734 (18.64) Ref. Max.
MS4820D 0.485 (12.32) 0.142 (3.61)
FS4820D 0.040 (1.02)
MALE CONTACT
FEMALE CONTACT
Max. 0.697 (17.70) Ref.
SOLDER WIRE TERMINATION
Max. 0.697 (17.70) Ref.
MS4920D 0.448 (11.38) 0.142 (3.61)
FS4920D 0.040 (1.02)
MALE CONTACT
FEMALE CONTACT
DIMENSIONS INCHES (MILLIMETERS) DIMENSIONS SUBJECT CHANGE
TECHNICAL CHARACTERISTICS
MATERIALS FINISHES:
Insulators: Contacts: Plating: Teflon, PTFE. Male contacts, brass. Female contacts, phosphor bronze. 0.000030 inch (0.75µ) gold over nickel, 0.000050 inch (1.25µ) gold over nickel.
MECHANICAL CHARACTERISTICS:
Size Removable Contacts: Durability: Vibration: Shock: Rear insertion, front release. cycles minimum. from 30g-11ms.
ELECTRICAL CHARACTERISTICS:
HIGH VOLTAGE CONTACTS Flash Over Voltage: 3600 r.m.s. Proof Voltage: 2700 r.m.s. Initial Contact Resistance: 0.008 ohms maximum.
CLIMATIC CHARACTERISTICS:
Temperature Range: -55°C +125°C.
Positronic Industries, Inc.
INDUSTRIAL MILITARY QUALITY SUBMINIATURE-D CONNECTORS
Series
MILITARY SHELTERED INDOOR/OUTDOOR ENVIRONMENTAL APPLICATIONS CRIMP REMOVABLE CONTACT SERIES
Size Contacts Crimp Removable Military/Industrial Quality Connectors D.E.S.C. 85039
U.L. Recognized Recognized File #E49351 File #LR54219 807-3 Telecommunication U.L. File #E140980 Series connectors military/industrial quality rectangular connectors designed sheltered, mildly corrosive environments having wide range temperature, pressure humidity changes. Series connectors offer mixed crimp-removable contact combinations power, shielded, high voltage signal contacts within same connector body. Refer size removable contacts power, shielded, high voltage section, page through technical characteristics. connector variants offered standard shell sizes. wide assortment cable support hoods locking systems available from stock. Series connectors also offer Blind Mating connector system applications requiring connector couplings recessed areas mobile power coupling systems. Series connectors utilize precision machined contacts they meet applicable performance dimensional requirements 807-3, D.E.S.C. 85039 MIL-DTL-24308.
*CBC SERIES CONTACT VARIANTS
FACE VIEW MALE REAR VIEW FEMALE
SHELL SIZE
Note: Additional contact variants tooled customer request. 27W2 variant currently available female only.
SHELL SIZE
11W1
SHELL SIZE
13W3
17W2
21W1
SHELL SIZE
25W3 27W2
21WA4
SHELL SIZE
24W7
36W4
43W2
47W1
Positronic Industries, Inc.
INDUSTRIAL MILITARY QUALITY SUBMINIATURE-D CONNECTORS
Series
MILITARY SHELTERED INDOOR/OUTDOOR ENVIRONMENTAL APPLICATIONS CRIMP REMOVABLE CONTACT SERIES
SERIES TECHNICAL CHARACTERISTICS
MATERIALS FINISHES:
Insulator: Signal Contacts: Glass filled polyester MIL-M-24519, 94V-0, blue color. Male contacts precision machined brass alloy. Female contacts precision machined high tensile copper alloy with stainless steel shroud open entry Robi-D design. Gold flash over nickel plate gold 0.000050 (1.25 microns) over nickel plate. Precision machined copper alloy male contacts female contacts. Retainers beryllium copper. Gold flash over nickel.
MECHANICAL CHARACTERISTICS:
Signal Contacts, Crimp Removable: Size contacts male 0.040 inch (1.02mm) diameter; Female closed entry design with stainless steel shroud open entry Robi-D design. lbs. (40N). Power, shielded high voltage lbs. (98N) Closed barrel crimp, wire sizes (1.0mm2) through (0.05 mm2) Size contact, male contact 0.142 inch (3.61mm) diameter. Male female contacts have terminations wire sizes 8,12 AWG. table maximum cable sizes contact termination dimensions, page Straight terminations 0.041 inch (1.04mm) minimum hole diameter. Male shells dimpled EMI/ESD ground paths. Trapezoidally shaped shells polarized jackscrews. Jackscrews. Series, operations, open entry contact, 1000 operations, closed entry contact with 0.000050 (1.25 microns) gold plating. 512-5.
Contact Retention Insulator: Crimp Contact Terminations: Power Contacts, Removable, Crimp Solder Termination:
Signal Contact Plating: Power, Shielded High Voltage Contacts:
Power Contact Plating: Shielded High Voltage Contact Plating: Signal contact plating, gold 0.000030 inch (0.75 microns) over nickel. Shielded body plating, gold flash over nickel. Shells: Steel brass with plate; zinc with dichromate seal, stainless steel passivated. Mounting Spacers Brackets: Nylon plastic, brass with plate; zinc with dichromate seal. Jackscrew Systems: Steel with zinc dichromate seal, clear zinc plate. Hoods: Composite plastic UL94V-0, brass steel with zinc plate dichromate seal.
Shielded Contacts, Removable: High Voltage Contacts: Shells: Polarization: Locking Systems: Mechanical Operations, Signal Contacts:
ELECTRICAL CHARACTERISTICS:
SIGNAL CONTACTS
Contact Current Rating: amperes nominal. Initial Contact Resistance: 0.008 ohms maximum. Proof Voltage: 1000 r.m.s.
CLIMATIC CHARACTERISTICS:
Temperature Range: Damp Heat, Steady State: -55°C +125°C. days.
POWER CONTACTS
Contact Current Rating: amperes nominal. Initial Contact Resistance: 0.005 ohms maximum. Proof Voltage: 1000 r.m.s.
SHIELDED CONTACTS
Initial Contact Resistance: 0.008 ohms maximum. Nominal Impedance: ohms. Insertion Loss: -0.46 -1.5 VSWR: 1.15 average 1.56 average Above values measured using frequency domain techniques. Proof Voltage: 1000 r.m.s. HIGH VOLTAGE CONTACTS Flash over Voltage: 3600 r.m.s. Proof Voltage: 2700 r.m.s. Initial Contact Resistance: 0.008 ohms maximum. CONNECTOR Insulator Resistance: ohms. Clearance Creepage Distance: 0.039 inch (1.0mm) minimum. Working Voltage: r.m.s.
CBC11W1M10Z00 WITH MS4012D CONTACT CBC11W1F100T20 WITH FS4012D CONTACT
Positronic Industries, Inc.
INDUSTRIAL MILITARY QUALITY SUBMINIATURE-D CONNECTORS
Series
MILITARY SHELTERED INDOOR/OUTDOOR ENVIRONMENTAL APPLICATIONS CRIMP REMOVABLE CONTACT SERIES
CBC7W2F00000
CBC17W2M00000
STANDARD SHELL ASSEMBLY
TYPICAL CONNECTOR VIEW
0.375 (9.53) Max.
0.220 (5.59) Max. ±0.008 0.036 (0.91) ±0.010 0.050 (1.27)
0.220 (5.59) Max. 0.375 (9.53) Max.
0.120 (3.05) ±0.005 Mounting hole, places
SHELL SIZE SHELL SIZE MALE SHELL SIZE FEMALE SHELL SIZE MALE SHELL SIZE FEMALE SHELL SIZE MALE SHELL SIZE FEMALE SHELL SIZE MALE SHELL SIZE FEMALE SHELL SIZE MALE SHELL SIZE FEMALE SHELL SIZE MALE SHELL SIZE FEMALE
±0.015 1.213 (30.81) 1.213 (30.81) 1.541 (39.14) 1.541 (39.14) 2.088 (53.04) 2.088 (53.04) 2.729 (69.32) 2.729 (69.32) 2.635 (66.93) 2.635 (66.93) 2.729 (69.32) 2.729 (69.32)
±0.005
±0.005 0.666 (16.92)
±0.005 0.984 (24.99) 0.984 (24.99)
±0.005
±0.005 0.329 (8.36)
±0.015 0.494 (12.55) 0.494 (12.55)
±0.010 0.759 (19.28) 0.759 (19.28) 1.083 (27.51) 1.083 (27.51) 1.625 (41.28) 1.625 (41.28) 2.272 (57.71) 2.272 (57.71) 2.178 (55.32) 2.178 (55.32) 2.302 (58.47) 2.302 (58.47)
±0.010 0.422 (10.72) 0.422 (10.72) 0.422 (10.72) 0.422 (10.72) 0.422 (10.72) 0.422 (10.72) 0.422 (10.72) 0.422 (10.72) 0.534 (13.56) 0.534 (13.56) 0.596 (15.14) 0.596 (15.14)
±0.005 0.233 (5.92) 0.243 (6.17) 0.233 (5.92) 0.243 (6.17) 0.230 (5.84) 0.243 (6.17) 0.230 (5.84) 0.243 (6.17) 0.230 (5.84) 0.243 (6.17) 0.230 (5.84) 0.243 (6.17)
±0.010 0.422 (10.72) 0.429 (10.90) 0.422 (10.72) 0.429 (10.90) 0.426 (10.82) 0.429 (10.90) 0.426 (10.82) 0.429 (10.90) 0.426 (10.82) 0.429 (10.90) 0.426 (10.82) 0.429 (10.90)
0.643 (16.33) 0.994 (25.25) 0.971 (24.66) 1.534 (38.96) 1.511 (38.38) 2.182 (55.42) 2.159 (54.84) 2.079 (52.81) 2.064 (52.43) 2.212 (56.18) 2.189 (55.60)
0.311 (7.90) 0.329 (8.36) 0.311 (7.90) 0.329 (8.36) 0.311 (7.90) 0.329 (8.36) 0.311 (7.90) 0.441 (11.20) 0.423 (10.74) 0.503 (12.78) 0.485 (12.32)
1.312 (33.32) 1.312 (33.32) 1.852 (47.04) 1.852 (47.04) 2.500 (63.50) 2.500 (63.50) 2.406 (61.11) 2.406 (61.11) 2.500 (63.50) 2.500 (63.50)
0.494 (12.55) 0.494 (12.55) 0.494 (12.55) 0.494 (12.55) 0.494 (12.55) 0.494 (12.55) 0.605 (15.37) 0.605 (15.37) 0.668 (16.97) 0.668 (16.97)
DIMENSIONS INCHES (MILLIMETERS) DIMENSIONS SUBJECT CHANGE
Positronic Industries, Inc.
INDUSTRIAL MILITARY QUALITY SUBMINIATURE-D CONNECTORS
Series
MILITARY SHELTERED INDOOR/OUTDOOR ENVIRONMENTAL APPLICATIONS CRIMP REMOVABLE CONTACT SERIES
CRIMP REMOVABLE CONTACT CONNECTOR SIGNAL CRIMP CONTACTS
CLOSED CRIMP BARREL
FEMALE CONTACT ("CLOSED ENTRY" DESIGN)
Color Code
MALE CONTACT
Color Code
0.040 (1.02)
0.170 (4.32) Material Leaded nickel copper.
Stainless Steel Shroud Material Brass.
0.170 (4.32) Plating Gold flash over nickel 0.000050 inch (1.25µ) gold over copper military specification contacts.
Color Code ORANGE/BLUE/WHITE military
Plating Gold flash over nickel 0.000050 inch (1.25µ) gold over copper military specification contacts.
Color Code ORANGE/BLUE/GRAY military
specification contacts. PART NUMBER FC6020D FC6026D
M39029/63-368
specification contacts. 0.044 (1.12) 0.027 (0.69) 0.044 (1.12) 0.066 (1.68) 0.066 (1.68) 0.066 (1.68) PART NUMBER MC6020D MC6026D
M39029/64-369
WIRE SIZE AWG/(mm2) (0.5/0.3/0.25) (0.12/0.08/0.05) (0.5/0.3/0.25)
0.538 (13.67) 0.538 (13.67) 0.538 (13.67)
WIRE SIZE AWG/(mm2) (0.5/0.3/0.25) (0.12/0.08/0.05) (0.5/0.3/0.25)
0.550 (13.97) 0.550 (13.97) 0.550 (13.97)
0.044 (1.12) 0.027 (0.69) 0.044 (1.12)
0.066 (1.68) 0.066 (1.68) 0.066 (1.68)
Crimp contacts supplied kitted with connector ordered separately. page crimp tool information.
FEMALE CONTACT ("ROBI-D OPEN ENTRY" DESIGN)
0.170 (4.32)
MALE CONTACT (1.0mm2) max.
0.927 (23.55)
Material Phosphor bronze. Plating Gold flash over nickel. PART NUMBER FC6520D WIRE SIZE AWG/(mm2) (0.5/0.3/0.25) 0.538 (13.67) 0.044 (1.12) 0.066 (1.68) 0.040 (1.02) 0.170 (4.32)
0.055 (1.40) 0.086 (2.18)
Part number: MC6018D
Material Brass. Plating Gold flash over nickel.
FEMALE CONTACT ("CLOSED ENTRY" DESIGN) (1.0mm2) max.
0.915 (23.24)
REELS AUTOMATIC FEED PNEUMATIC CRIMP TOOLS
Contacts supplied plastic carriers, packaged reels holding 2,000 contacts with automatic feed pneumatic crimp tools, catalog part number 9550-1. same type carrier used both male female contacts. male female crimp contacts ordered reels adding letter after contact part number, such MC6020DR male contact FC6026DR female contact.
0.055 (1.40) 0.086 (2.18) 0.170 (4.32) Stainless steel shroud
Part number: FC6018D
Material Phosphor bronze. Plating Gold flash over nickel. DIMENSIONS INCHES (MILLIMETERS) DIMENSIONS SUBJECT CHANGE Enlarged section plastic contact carriers
Positronic Industries, Inc.
INDUSTRIAL MILITARY QUALITY SUBMINIATURE-D CONNECTORS
Series
MILITARY SHELTERED INDOOR/OUTDOOR ENVIRONMENTAL APPLICATIONS CRIMP REMOVABLE CONTACT SERIES
ORDERING INFORMATION CODE NUMBERING SYSTEM
Specify Complete Connector Following Steps Through Insert When Step Used
STEP
STEP Basic Series
Series.
*STEP Special Options
Consult Sales Department 759.0 Blind Mate Pilot 759.1 Blind Mate Panel
STEP Connector Variants
Shell Size Shell Size 7W2, 11W1 Shell Size 9W4, 13W3, 17W2, 21W1 Shell Size 21WA4, 25W3, 27W2*** Shell Size 24W7, 36W4, 43W2, 47W1
STEP Shell Options
Zinc plated with Dichromate Seal Stainless Steel Plated Plated Dimpled
*STEP Locking Polarizing Systems
None Fixed Female Jackscrews Fixed Female Jackscrews Fixed Male Female Polarized Jackscrews Rotating Male Jackscrews Rotating Male Screw Locks Rotating Male Female Polarized Jackscrews
STEP Connector Gender
Male Female
*STEP Hoods
STEP Type Contacts
Connector ordered without contacts. Order Signal, Power, Shielded High Voltage contacts separately. pages contact part numbers. Kitted contacts supplied sealed bags. Signal contacts, AWG-24 (0.5mm2-0.25mm2). Signal contacts, AWG-24 (0.5mm2-0.25mm2) with MC/FC 4012D Power Contact. Signal contacts, AWG-24 (0.5mm2-0.25mm2) with MC/FC 4016D power contact. Signal contacts, AWG-24 (0.5mm2-0.25mm2) with MCC/FCC 4101D shielded contacts. Signal contacts, AWG-24 (0.5mm2-0.25mm2) with MCC/FCC 4102D shielded contacts. None Hood, Opening, Metal, shell sizes through Hood, EMI/RFI, Metal, shell sizes through Hood, Side Opening, robust extended height, plastic composite, with rotating jackscrews, shell sizes through
*For additional information accessories listed
steps Accessory Catalog.
Hood recommended with series
shell sizes through Connector variant 27W2 currently available female only.
*STEP Mounting Style
Mounting Hole, 0.120 (3.05) Float Mounts, Universal Swaged Spacer, 4-40 Threads, 0.125 (3.18) Length Swaged Locknut, 4-40 Threads
Positronic Industries, Inc.
INDUSTRIAL MILITARY QUALITY SUBMINIATURE-D CONNECTORS
Series
MILITARY SHELTERED INDOOR/OUTDOOR ENVIRONMENTAL APPLICATIONS CRIMP REMOVABLE CONTACT SERIES
CRIMP REMOVABLE CONTACT CONNECTOR CRIMPING INFORMATION SERIES CRIMP SIGNAL CONTACTS
Step Strip wire indicated length
Insulation ±0.020 0.160 (4.06) Take care -Damage remove strands -Untwist overtwist strands -Leave insulation particles strands -Damage insulation
Stranded wire
Correctly stripped wire
Strands damaged removed stripping tool
Strands overtwisted
Insulation incorrectly
Particles insulation stripped part wire
Strands untwisted
Wire insulation damaged
Examples stripping faults Step Crimp wire contact
hand crimp tool: -Place contact into crimping tool -Insert wire into contact -Center contact slowly closing crimping tool until crimp indenters make contact with crimp barrel -Complete cycle crimping tool smooth motion -Remove crimped contact
automatic feed pneumatic crimp tool: -Insert wire into contact, positioned crimp tool plastic carrier -Depress activating devise crimping tool start crimping cycle -Remove crimped contact
Positronic Industries, Inc.
INDUSTRIAL MILITARY QUALITY SUBMINIATURE-D CONNECTORS
Series
MILITARY SHELTERED INDOOR/OUTDOOR ENVIRONMENTAL APPLICATIONS CRIMP REMOVABLE CONTACT SERIES
CRIMP REMOVABLE CONTACT CONNECTOR CRIMPING INFORMATION SERIES CRIMP SIGNAL CONTACTS
Step Inspect crimp
tools: -Strands visible through inspection hole -Strands visible beyond insulation support -Crimped contact meet recommended conductor tensile force shown chart -Check peeled gold bent contact Crimp meet recommended tensile strength
Correctly crimped contact
Wire insulation, Typ.
Cross section correctly crimped contact
Stripped wires compressed improved conduction Strands visible beyond insulation support Strands visible through inspection hole
crimp indents
Crimp indents close inspection hole
Stripped part wire long Positronic recommended conductor tensile strength WIRE SIZE AXIAL LOAD
Stripped part wire short
Crimp indents incorrectly located
Examples crimping faults
18AWG lbs. (1.0mm2) (125 20AWG lbs. (0.5mm2) 22AWG lbs. (0.3mm2) 24AWG lbs. (0.25mm2) 26AWG lbs. (0.12mm2) 28AWG lbs. (0.08mm2) 30AWG lbs. (0.05mm2) (6.7
Positronic recommended tools signal contacts. more information crimp tools accessories page. POSITIONERS FC6020D, FC6026D, MC6020D, MC6026D, M39029/63-368, M39029/64-369 9502-5 Supplied reels
CRIMP TOOLS
POSITIONERS FC6018D, MC6018D
9507, HAND CRIMP TOOL 9550-1, AUTOMATIC FEED PNEUMATIC STRIP CRIMP TOOL
9502-11
Conductor tensile strength values derived using silver-tin plated copper wires. Values change depending upon what type wire used.
Positronic Industries, Inc.
INDUSTRIAL MILITARY QUALITY SUBMINIATURE-D CONNECTORS
Series
MILITARY SHELTERED INDOOR/OUTDOOR ENVIRONMENTAL APPLICATIONS CRIMP REMOVABLE CONTACT SERIES
AUTOMATIC FEED, STRIP CRIMP TOOLS, PNEUMATICALLY ACTUATED
Part 9550-1 This fast cycling automatic feed strip crimp tool produces indent crimp wire sizes (1.0mm2) through (0.03mm2). Series contacts must ordered reels. order, specify part number 9550-1. Foot control valve supplied standard accessory.
MINIATURE STEP ADJUSTABLE TOOL (M22520/2-01)
Part 9507 This miniature step adjustable hand crimping tool produces indent crimp configuration will crimp wire sizes (1.0mm2) through (0.03mm2). crimp wire size (1.0mm2), order contact positioner 9502-11. crimp wire size (0.5mm2) through (0.05mm2) order contact positioner 9502-5. Each positioner equipped with data plate which gives correct crimp-depth setting each wire size, must used with 9507 tool frame best results when crimping Series contacts.
INSERTION/REMOVAL TOOL (M81969/1-02)
this tool used insert contacts into Series connectors. other used extract contacts. This accomplished sliding extraction down wire into connector until bottoms against contact. slight rotation while pushing will release contacts, which then extracted simultaneously pulling wire.
Part 9555-10 This fast cycling automatic feed strip crimp tool produces indent crimp wire sizes (10.0mm2) through (4.0mm2). Contacts must ordered reels. order, specify part number 9555-10. Foot control valve supplied standard accessory.
Positronic Industries, Inc.
Combo Dual Port Series
PROFESSIONAL QUALITY PRINTED BOARD MOUNT COMBINATION POWER SIGNAL CONTACT DUAL PORT VERTICALLY STACKED CONNECTOR ASSEMBLY
SHELTERED INDOOR/OUTDOOR ENVIRONMENTAL APPLICATIONS
Power Signal Contacts
U.L. Recognized File #E49351 Recognized File #LR54219 Telecommunication U.L. File #14095
Combo-Dual Port connector series offers several combinations power signal contacts within same connector assembly. Fifteen different combinations power signal contact stacked assemblies available within four standard shell sizes. connector assembly partially populated with either signal power contacts installed connector bodies customer selected contact positions. stacked connectors spaced apart dimensional spacings. special order, printed board mount ampere contacts replaced with size power, shielded high voltage contacts having crimp solder terminations. Signal contacts remain dual port configuration. Mounting angle brackets ordered riveted connector specifying options. Locking systems available utilizing 4-40 threaded jackscrew systems, polarized non-polarized, with quick-release vibration lock system either front rear panel mounted connectors. Combo-Dual Port Series connectors comply with dimensional requirements 807-2 DESC 85039.
COMBO-DUAL PORT TECHNICAL CHARACTERISTICS
MATERIALS FINISHES:
Insulator: Signal Contacts: Polyester, glass filled MIL-M-24519, 94V-0, blue color. Male contacts-precision machined copper alloy. Female contacts-precision machined high tensile phosphor bronze. Gold flash over nickel plate. Male contacts-precision machined copper alloy. Female contacts-precision machined high tensile copper alloy. Gold flash over nickel. Steel brass with plate zinc plate with dichromate seal. Steel brass with plate zinc with dichromate seal. Nylon, 94V-0, black color. Beryllium copper, plated. Steel with clear zinc plate zinc plate with dichromate seal. Lock tabs, steel with nickel plate.
MECHANICAL CHARACTERISTICS:
Signal Contacts: Size male contacts-0.040 inch (1.0mm) diameter. Female contactrugged open entry design. lbs. (40N) Printed board mount with terminations supported alignment bar. Termination diameter 0.028 inch (0.71mm). Size male contact-0.142 inch (3.61mm) diameter. Female contactopen entry closed entry options. lbs. (92N) Printed board mount with terminations 0.078 inch (1.98mm) diameter. Size removable solder contacts with wire hole diameters 0.188 inch (4.78mm), 0.112 inch (2.84mm) 0.069 inch (1.75mm). Male connector shells dimpled EMI/ESD ground paths. Trapezoidally shaped shells polarized jackscrews. Riveted fasteners with 0.120 inch (3.05mm) diameter clearance hole, with 4-40 threads 4-40 threads with nylon lock insert. Rapid installation push-on fasteners. Jackscrews vibration locking system either front rear panel mounted connectors. operations minimum 512-5.
Plating: Power Contacts:
Contact Retention Insulator: Contact Terminations:
Plating: Shells: Mounting Spacers Brackets: Cross Bar: Push-On Fasteners: Jackscrew Systems: Vibration Lock Systems:
Power Contacts:
Contact Retention Insulator: Contact Terminations:
Shells: Polarization: Mounting Bracket Riveted Connector:
ELECTRICAL CHARACTERISTICS:
Signal Contacts:
Initial Contact Resistance: Power Contacts: amperes nominal. 0.008 ohms maximum. ampere nominal board mount. ampere nominal removable contacts with solder crimp terminations. 0.005 ohms maximum. 1000 r.m.s. ohms. 0.039 inch (1.0mm) r.m.s.
Initial Contact Resistance: Proof Voltage: Insulator Resistance: Clearance Creepage Distance (minimum): Working Voltage:
Mounting Printed Board: Locking Systems:
Mechanical Operations:
CLIMATIC CHARACTERISTICS:
Positronic Industries, Inc.
Temperature Range: Damp Heat, Steady State:
-55°C +125°C. days.
CBDP Series
PROFESSIONAL QUALITY PRINTED BOARD MOUNT COMBINATION POWER SIGNAL CONTACT DUAL PORT VERTICALLY STACKED CONNECTOR ASSEMBLY
SHELTERED INDOOR/OUTDOOR ENVIRONMENTAL APPLICATIONS
CONTACT VARIANTS
FACE VIEW MALE REAR VIEW FEMALE
SHELL SIZE
SHELL SIZE
11W1
SHELL SIZE
13W3
17W2
21W1
SHELL SIZE
13W6
17W5
21WA4
25W3
27W2
PRINTED BOARD MOUNT CONNECTOR
CONNECTOR UNIT, 0.283 (7.19) CONTACT EXTENSION
AMPERE MAXIMUM RATED POWER CONTACTS
4-40 THDS. TYP. 0.247 (6.27)
±0.008 0.036 (0.91) 0.220 (5.59) MAX.
Note: ampere 0.125 (3.18) power contacts ordered special request limited number CBDP variants. Contact factory details.
0.170 (4.32) ±0.003 0.028 TYP. (0.71) ±0.010 0.270 (6.86)
0.494 (12.55) ±0.003 0.078 TYP. (1.98)
0.283 (7.19) TYP. 0.112 (2.84) TYP.
0.112 (2.84) TYP.
0.150 (3.81) TYP. TYPICAL PART NUMBER: CBDPB7W2MN8T2/7W2MN8T6X 0.745 (18.92)
±0.010 0.580 (14.73)
CONNECTOR VARIANT SHELL SIZE
1.213 (30.81) 1.541 (39.14) 2.088 (53.04) 2.729 (69.32)
0.984 (24.99) 1.312 (33.32) 1.852 (47.04) 2.500 (63.50)
CONNECTOR DESIGNATION CBDPB CBDPC
0.750 (19.05) 0.900 (22.86)
1.244 (31.60) 1.394 (35.41)
0.256 (6.50) 0.406 (10.31)
SHELL SIZE SHELL SIZE SHELL SIZE
DIMENSIONS INCHES (MILLIMETERS) DIMENSIONS SUBJECT CHANGE
Note: Printed board power contacts (size replaced with size removable power, shielded high voltage contact having solder crimp terminations.
Positronic Industries, Inc.
CBDP Series
PROFESSIONAL QUALITY PRINTED BOARD MOUNT COMBINATION POWER SIGNAL CONTACT DUAL PORT VERTICALLY STACKED CONNECTOR ASSEMBLY
SHELTERED INDOOR/OUTDOOR ENVIRONMENTAL APPLICATIONS
PRINTED BOARD CONTACT HOLE PATTERN
Hole identification shown female connector over male connector. Mount connector with mating face positioned follow direction arrow.
0.112 (2.84) 0.035 (0.89) 0.310 (7.87) 0.013 (0.33) 0.162 (4.11) 0.218 (5.54) 0.492 (12.50) 5W1/5W1 0.112 (2.84) 0.035 (0.89) 0.310 (7.87) 0.013 (0.33) 0.656 (16.66) 11W1/11W1 0.035 (0.89) 0.310 (7.87) 0.013 (0.33) 0.108 (2.74) 0.162 (4.11) 0.306 (7.77) 0.570 (14.48) 0.926 (23.52) 9W4/9W4 0.112 (2.84) 0.035 (0.89) 0.310 (7.87) 0.013 (0.33) 0.054 (1.37) 0.109 (2.77) 0.544 (13.82) 0.926 (23.52) 17W2/17W2 0.056 (1.42) 0.112 (2.84) 0.056 (1.42) 0.108 (2.74) 0.162 (4.11) 0.216 (5.49) 0.056 (1.42) 0.056 (1.42) 0.310 (7.87)
0.262 (6.65) 0.069 (1.75) 0.310 (7.87) 0.270 (6.86) 0.656 (16.66) 3W3/3W3 0.013 (0.33) 0.656 (16.66) 0.035 (0.89)
0.112 (2.84) 0.056 (1.42)
0.054 (1.37) 0.108 (2.74) 0.270 (6.86)
7W2/7W2 0.262 (6.65) 0.069 (1.75) 0.310 (7.87) 0.034 (0.86) 0.268 (6.81) 0.570 (14.48) 0.926 (23.52) 5W5/5W5 0.112 (2.84) 0.035 (0.89) 0.310 (7.87) 0.013 (0.33) 0.054 (1.37) 0.108 (2.74) 0.306 (7.77) 0.570 (14.48) 0.926 (23.52) 13W3/13W3 0.112 (2.84) 0.035 (0.89) 0.310 (7.87) 0.013 (0.33) 0.109 (2.77) 0.163 (4.14) 0.218 (5.54) 0.926 (23.52) 21W1/21W1 0.056 (1.42) 0.056 (1.42)
Suggest 0.045 (1.14) hole signal contact termination positions. Suggest 0.098 (2.49) hole 0.078 (1.98) power contact termination positions. Suggest 0.123 ±0.003 (3.12) hole mounting connector with push-on fasteners. Mounting holes must move 0.020 (0.51) ±0.010 opposite direction arrow unriveted mounting bracket with connectors.
DIMENSIONS INCHES (MILLIMETERS) DIMENSIONS SUBJECT CHANGE
Positronic Industries, Inc.
CBDP Series
PROFESSIONAL QUALITY PRINTED BOARD MOUNT COMBINATION POWER SIGNAL CONTACT DUAL PORT VERTICALLY STACKED CONNECTOR ASSEMBLY
SHELTERED INDOOR/OUTDOOR ENVIRONMENTAL APPLICATIONS
PRINTED BOARD CONTACT HOLE PATTERN
Hole identification shown female connector over male connector. Mount connector with mating face positioned follow direction arrow. 0.112 (2.84) 0.262 (6.65) 0.310 (7.87) 0.150 (3.81) 0.069 (1.75) 0.250 (6.35) TYP. 0.650 (16.51) 0.900 (22.86) 1.250 (31.75) 0.600 (15.24) 0.265 (6.73) 1.250 (31.75) 0.310 (7.87) 0.013 (0.33) 0.109 (2.77) 0.652 (16.56) 0.707 (17.96) 0.092 (2.34) 0.035 (0.89) 0.056 (1.42)
8W8/8W8
13W6/13W6
0.112 (2.84) 0.035 (0.89) 0.310 (7.87) 0.013 (0.33) 0.055 (1.40) 0.109 (2.77) 0.618 (15.70) 1.250 (31.75) 0.275 (6.99) 0.343 (8.71) 0.056 (1.42) 0.310 (7.87) 0.013 (0.33) 0.893 (22.68) 1.250 (31.75) 0.035 (0.89)
0.112 (2.84) 0.056 (1.42)
0.055 (1.40) 0.109 (2.77) 0.618 (15.70)
17W5/17W5
21WA4/21WA4
0.112 (2.84) 0.035 (0.89) 0.310 (7.87) 0.013 (0.33) 0.893 (22.68) 1.250 (31.75) 0.055 (1.40) 0.109 (2.77) 0.618 (15.70) 0.056 (1.42) 0.310 (7.87) 0.013 (0.33) 0.893 (22.68) 1.250 (31.75) 0.035 (0.89)
0.112 (2.84) 0.056 (1.42)
0.055 (1.40) 0.109 (2.77)
27W2/27W2
25W3/25W3
Suggest 0.045 (1.14) hole signal contact termination positions. Suggest 0.098 (2.49) hole 0.078 (1.98) power contact termination positions. Suggest 0.123 ±0.003 (3.12) hole mounting connector with push-on fasteners. Mounting holes must move 0.020 (0.51) ±0.010 opposite direction arrow unriveted mounting bracket with connectors.
DIMENSIONS INCHES (MILLIMETERS) DIMENSIONS SUBJECT CHANGE
Positronic Industries, Inc.
CBDP Series
PROFESSIONAL QUALITY PRINTED BOARD MOUNT COMBINATION POWER SIGNAL CONTACT DUAL PORT VERTICALLY STACKED CONNECTOR ASSEMBLY
SHELTERED INDOOR/OUTDOOR ENVIRONMENTAL APPLICATIONS
ORDERING INFORMATION CODE NUMBERING SYSTEM
Specify Complete Connector Following Steps Through Insert When Step Used
STEP
Upper Connector STEP Basic Series
CBDPB Series CBDPC Series
CBDPB
Lower Connector
Options same Upper Connector Steps
STEP Special Options
Consult Sales Department
STEP CBDP Series Connector Variants
Shell Size Shell Size 3W3, 7W2, 11W1 Shell Size 5W5, 9W4, 13W3, 17W2, 21W1 Shell Size 8W8, 13W6, 17W5, 21WA4, 25W3, 27W2
Note: Size removable power contacts with solder crimp terminations with power ratings amperes ordered lieu board mounted power contact. Removable size shielded high voltage contacts also ordered separately lieu power contact. pages through contact part numbers.
STEP Shell Options
Zinc Plate with Dichromate Seal Plated Plated Dimpled
STEP Connector Gender
Male Female
STEP Locking, Polarizing, Mounting Push-on Fastener Systems
None Bracket, Mounting, Metal, Swaged Connector with 4-40 Thread, Fixed Female Jackscrews Cross Bracket, Mounting, Metal, Swaged Connector with 0.120 (3.05) Mounting Hole with Cross Bracket, Mounting, Metal, Swaged Connector with 4-40 Threads with Cross Bracket, Mounting, Metal, Swaged Connector with 4-40 Locknut with Cross Bracket, Mounting, Metal, Swaged Connector with 4-40 Thread, Fixed Female Jackscrews with Cross Push-On Fastener Bracket, Mounting, Metal, Swaged Connector with 4-40 Threads with Cross Push-on Fastener Bracket, Mounting, Metal, Swaged Connector with 4-40 Threads with Cross Push-on Fastener Bracket, Mounting, Metal, Swaged Connector with 4-40 Locknut with Cross Push-on Fastener Fixed Female Jackscrews Fixed Female Jackscrews Fixed Male Female Polarized Jackscrews
Positronic Industries, Inc.
Series
DESC
85040DAEPT 85040DAEST 85040DAEPR 85040DAESR 85040GAEPT 85040GAEST 85040GAEPR 85040GAESR 85040GBEPT 85040GBEST 85040GBEPR 85040GBESR 85040NAEPT 85040NAEST 85040NAEPR 85040NAESR 85040MAEPT 85040MAEST 85040MAEPR 85040MAESR 85041DAEPT 85041DAEST 85041DAEPR 85041DAESR 85041GAEPT 85041GAEST 85041GAEPR 85041GAESR 85041GBEPT 85041GBEST 85041GBEPR 85041GBESR 85041NAEPT 85041NAEST 85041NAEPR 85041NAESR 85041MAEPT 85041MAEST 85041MAEPR 85041MAESR 85043GULPT 85043GULST 85043GULPR 85043GULSR 85044DAEPT 85044DAEST 85044DAEPR 85044DAESR 85044GAEPT 85044GAEST 85044GAEPR 85044GAESR 85044GBEPT 85044GBEST 85044GBEPR 85044GBESR
DESC CROSS REFERENCE
POSITRONIC
CBC7W2M1F000-50-799.2 CBC7W2F1F000-50-799.2 CBC7W2M10000-50-799.0 CBC7W2F10000-50-799.0 CBC7W2M1F00C-50 CBC7W2F1F00C-50 CBC7W2M1000C-50 CBC7W2F1000C-50 CBM7W2M2F00C-50 CBM7W2F2F00C-50 CBM7W2M2000C-50 CBM7W2F2000C-50 CBC7W2M1F000-50-403.0 CBC7W2F1F000-50-403.0 CBC7W2M10000-50-403.0 CBC7W2F10000-50-403.0 CBC7W2M1F000-50-403.4 CBC7W2F1F000-50-403.4 CBC7W2M10000-50-403.3 CBC7W2F10000-50-403.3 CBC11W1M1F000-50-799.2 CBC11W1F1F000-50-799.2 CBC11W1M10000-50-799.0 CBC11W1F10000-50-799.0 CBC11W1M1F00C-50 CBC11W1F1F00C-50 CBC11W1M1000C-50 CBC11W1F1000C-50 CBM11W1M2F00C-50 CBM11W1F2F00C-50 CBM11W1M2000C-50 CBM11W1F2000C-50 CBC11W1M1F000-50-403.0 CBC11W1F1F000-50-403.0 CBC11W1M10000-50-403.0 CBC11W1F10000-50-403.0 CBC11W1M1F000-50-403.4 CBC11W1F1F000-50-403.4 CBC11W1M10000-50-403.3 CBC11W1F10000-50-403.3 CBM5W5M0F00C CBM5W5F0F00C CBM5W5M0000C CBM5W5F0000C CBC17W2M1F000-50-799.2 CBC17W2F1F000-50-799.2 CBC17W2M10000-50-799.0 CBC17W2F10000-50-799.0 CBC17W2M1F00C-50 CBC17W2F1F00C-50 CBC17W2M1000C-50 CBC17W2F1000C-50 CBM17W2M2F00C-50 CBM17W2F2F00C-50 CBM17W2M2000C-50 CBM17W2F2000C-50
DESC
85044NAEPT 85044NAEST 85044NAEPR 85044NAESR 85044MAEPT 85044MAEST 85044MAEPR 85044MAESR 85045DAEPT 85045DAEST 85045DAEPR 85045DAESR 85045GAEPT 85045GAEST 85045GAEPR 85045GAESR 85045GBEPT 85045GBEST 85045GBEPR 85045GBESR 85045NAEPT 85045NAEST 85045NAEPR 85045NAESR 85045MAEPT 85045MAEST 85045MAEPR 85045MAESR 85047GULPT 85047GULST 85047GULPR 85047GULSR 85048GBEPT 85048GBEST 85048GBEPR 85048GBESR 85049 85050 85051 85052 85053 85054GBEPT 85054GBEST 85054GBEPR 85054GBESR 89046-001 89047-001 89048-001 89049-001 89050-001
POSITRONIC
CBC17W2M1F000-50-403.0 CBC17W2F1F000-50-403.0 CBC17W2M10000-50-403.0 CBC17W2F10000-50-403.0 CBC17W2M1F000-50-403.4 CBC17W2F1F000-50-403.4 CBC17W2M10000-50-403.3 CBC17W2F10000-50-403.3 CBC13W3M1F000-50-799.2 CBC13W3F1F000-50-799.2 CBC13W3M10000-50-799.0 CBC13W3F10000-50-799.0 CBC13W3M1F00C-50 CBC13W3F1F00C-50 CBC13W3M1000C-50 CBC13W3F1000C-50 CBM13W3M2F00C-50 CBM13W3F2F00C-50 CBM13W3M2000C-50 CBM13W3F2000C-50 CBC13W3M1F000-50-403.0 CBC13W3F1F000-50-403.0 CBC13W3M10000-50-403.0 CBC13W3F10000-50-403.0 CBC13W3M1F000-50-403.4 CBC13W3F1F000-50-403.4 CBC13W3M10000-50-403.3 CBC13W3F10000-50-403.3 CBM8W8M0F00C CBM8W8F0F00C CBM8W8M0000C CBM8W8F0000C CBM21WA4M2F00C-50 CBM21WA4F2F00C-50 CBM21WA4M2000C-50 CBM21WA4F2000C-50 OFFERED OFFERED OFFERED OFFERED OFFERED CBM24W7M2F00C-50 CBM24W7F2F00C-50 CBM24W7M2000C-50 CBM24W7F2000C-50 MS4016D-50 FS4016D-50 OFFERED OFFERED MS4008D-50
Removable contacts were tested shock vibration using connectors holding fixture. Tests were performed connector specifications.
Positronic Industries, Inc.
Series
DESC
89051-001 89052-001 89053-001 89054-001 89055-001 89056-001 89057-001 89058-A 89058-B 89058-C 89058-D 89059-A 89059-B 89059-C 89059-D 89060-A 89060-B 89060-C 89060-D 89061-A 89061-B 89061-C 89061-D 89074DAEPT 89074DAEST 89074DAEPR 89074DAESR 89074GAEPT 89074GAEST 89074GAEPR 89074GAESR 89074GBEPT 89074GBEST 89074GBEPR 89074GBESR 89074NAEPT 89074NAEST 89074NAEPR 89074NAESR 89074MAEPT 89074MAEST 89074MAEPR 89074MAESR 89075GULPT 89075GULST 89075GULPR 89075GULSR 89076GBEPT 89076GBEST 89076GBEPR 89076GBESR 89077GBEPT 89077GBEST 89077GBEPR 89077GBESR
DESC CROSS REFERENCE
POSITRONIC
FS4008D-50 OFFERED OFFERED MS4820-50 FS4820-50 FS4920-50 MS4920-50 MC4101M MC4102M MC4103M MC4104M FC4101M FC4102M FC4103M FC4104M MC4201M MC4202M MC4203M MC4204M FC4201M FC4202M FC4203M FC4204M CBC5W1M1F000-50-799.2 CBC5W1F1F000-50-799.2 CBC5W1M10000-50-799.0 CBC5W1F10000-50-799.0 CBC5W1M1F00C-50 CBC5W1F1F00C-50 CBC5W1M1000C-50 CBC5W1F1000C-50 CBM5W1M2F00C-50 CBM5W1F2F00C-50 CBM5W1M2000C-50 CBM5W1F2000C-50 CBC5W1M1F000-50-403.0 CBC5W1F1F000-50-403.0 CBC5W1M10000-50-403.0 CBC5W1F10000-50-403.0 CBC5W1M1F000-50-403.4 CBC5W1F1F000-50-403.4 CBC5W1M10000-50-403.3 CBC5W1F10000-50-403.3 CBM3W3M0F00C CBM3W3F0F00C CBM3W3M0000C CBM3W3F0000C CBM9W4M2F00C-50 CBM9W4F2F00C-50 CBM9W4M2000C-50 CBM9W4F2000C-50 CBM21W1M2F00C-50 CBM21W1F2F00C-50 CBM21W1M2000C-50 CBM21W1F2000C-50
DESC
89078GBEPT 89078GBEST 89078GBEPR 89078GBESR 89079GBEPT 89079GBEST 89079GBEPR 89079GBESR 89080DAEPT 89080DAEST 89080DAEPR 89080DAESR 89080GAEPT 89080GAEST 89080GAEPR 89080GAESR 89080GBEPT 89080GBEST 89080GBEPR 89080GBESR 89080NAEPT 89080NAEST 89080NAEPR 89080NAESR 89080MAEPT 89080MAEST 89080MAEPR 89080MAESR 89081GBEPT 89081GBEST 89081GBEPR 89081GBESR 89082GBEPT 89082GBEST 89082GBEPR 89082GBESR 89083DAEPT 89083DAEST 89083DAEPR 89083DAESR 89083GAEPT 89083GAEST 89083GAEPR 89083GAESR 89083GBEPT 89083GBEST 89083GBEPR 89083GBESR 89083NAEPT 89083NAEST 89083NAEPR 89083NAESR 89083MAEPT 89083MAEST 89083MAEPR 89083MAESR
POSITRONIC
CBM13W6M2F00C-50 CBM13W6F2F00C-50 CBM13W6M2000C-50 CBM13W6F2000C-50 CBM17W5M2F00C-50 CBM17W5F2F00C-50 CBM17W5M2000C-50 CBM17W5F2000C-50 CBC25W3M1F000-50-799.2 CBC25W3F1F000-50-799.2 CBC25W3M10000-50-799.0 CBC25W3F10000-50-799.0 CBC25W3M1F00C-50 CBC25W3F1F00C-50 CBC25W3M1000C-50 CBC25W3F1000C-50 CBM25W3M2F00C-50 CBM25W3F2F00C-50 CBM25W3M2000C-50 CBM25W3F2000C-50 CBC25W3M1F000-50-403.0 CBC25W3F1F000-50-403.0 CBC25W3M10000-50-403.0 CBC25W3F10000-50-403.0 CBC25W3M1F000-50-403.4 CBC25W3F1F000-50-403.4 CBC25W3M10000-50-403.3 CBC25W3F10000-50-403.3 CBM27W2M2F00C-50 CBM27W2F2F00C-50 CBM27W2M2000C-50 CBM27W2F2000C-50 CBM36W4M2F00C-50 CBM36W4F2F00C-50 CBM36W4M2000C-50 CBM36W4F2000C-50 CBC43W2M1F000-50-799.2 CBC43W2F1F000-50-799.2 CBC43W2M10000-50-799.0 CBC43W2F10000-50-799.0 CBC43W2M1F00C-50 CBC43W2F1F00C-50 CBC43W2M1000C-50 CBC43W2F1000C-50 CBM43W2M2F00C-50 CBM43W2F2F00C-50 CBM43W2M2000C-50 CBM43W2F2000C-50 CBC43W2M1F000-50-403.0 CBC43W2F1F000-50-403.0 CBC43W2M10000-50-403.0 CBC43W2F10000-50-403.0 CBC43W2M1F000-50-403.4 CBC43W2F1F000-50-403.4 CBC43W2M10000-50-403.3 CBC43W2F10000-50-403.3
Removable contacts were tested shock vibration using connectors holding fixture. Tests were performed connector specifications.
Positronic Industries, Inc.
NORTH AMERICAN HEADQUARTERS
UNITED STATES, Springfield, Missouri PUERTO RICO, Ponce Factory MEXICO
Factory Sales Engineering Offices Factory Sales Engineering Offices Factory Sales Engineering Offices (800)641-4054 (787)841-0920 (800)872-7674 (800)327-8272
CANADA
Factory Sales Engineering Offices
PACIFIC BASIN HEADQUARTERS
SINGAPORE, Asian Factory
Factory Sales Engineering Offices 65-6842-1419 Malaysia Sales Office 65-6842-1419 Taiwan Sales Office 8862-2937-8775 China (Shanghai) Sales Office 8621-6308-3640 Japan Sales Office 8135-661-3047 *Additional Technical Agents Australia, Zealand, India South Korea,Thailand, Philippines, Hong Kong Indonesia.
EUROPEAN HEADQUARTERS
FRANCE, Auch Factory EUROPE, Direct Sales Offices
Northern France Sales Office Southern France Sales Office Italy Sales Office Germany Sales Office Factory Sales Engineering Offices 2351
EUROPE, Technical Agents
MIDEAST, Technical Agents
Technical Agents Austria, Benelux, Denmark, Finland, Greece, Ireland, Scotland, Slovenia, Spain, Sweden, Switzerland United Kingdom
Technical Agents Israel Turkey
Campbell 8247 Springfield, 65801 (417) 866-2322 (417) 866-4115 Toll Free (800) 641-4054 info@connectpositronic.com
POSITRONIC INDUSTRIES, INC.
Zone Industrielle d'Engachies Route d'Engachies F-32020 Auch Cedex France Telephone Telecopieur contact@connectpositronic.com
POSITRONIC INDUSTRIES, S.A.S.
3014A Road #06-07 Singapore 408703 Telephone (65) 6842-1419 (65) 6842-1421 singapore@connectpositronic.com
POSITRONIC ASIA LTD.
www.connectpositronic.com
Other recent searches
UDN2998W - UDN2998W UDN2998W Datasheet
TPS61160 - TPS61160 TPS61160 Datasheet
TPS61161 - TPS61161 TPS61161 Datasheet
RP135 - RP135 RP135 Datasheet
HLMP-ELxx - HLMP-ELxx HLMP-ELxx Datasheet
HLMP-EHxx - HLMP-EHxx HLMP-EHxx Datasheet
HLMP-EDxx - HLMP-EDxx HLMP-EDxx Datasheet
GBU8005 - GBU8005 GBU8005 Datasheet
GBU810 - GBU810 GBU810 Datasheet
EN4020B - EN4020B EN4020B Datasheet
LA7151 - LA7151 LA7151 Datasheet
LA7151M - LA7151M LA7151M Datasheet
AW43-48 - AW43-48 AW43-48 Datasheet
1671270000 - 1671270000 1671270000 Datasheet
Privacy Policy | Disclaimer
© 2012 Datasheet Archive
