Data Sheet January 2006 FN2904.5 4MHz, High Supply Voltage Operat
|
|
|
Top Searches for this datasheet
HA-2640, HA-2645
Data Sheet January 2006 FN2904.5
4MHz, High Supply Voltage Operational Amplifiers
HA-2640 HA-2645 monolithic operational amplifiers which designed deliver unprecedented dynamic specifications high voltage internally compensated device. These dielectrically isolated devices offer very values offset voltage offset current coupled with large output voltage swing common mode input voltage. maximum reliability, these amplifiers offer unconditional output overload protection through current limiting chip temperature sensing circuit. This sensing device turns amplifier "off", when chip reaches certain temperature level. These amplifiers deliver ±35V common mode input voltage range, ±35V output voltage swing, ±40V supply range such designs regulators, power supplies, industrial control systems. 4MHz gain bandwidth 5V/µs slew rate make these devices excellent components high performance signal conditioning applications. Outstanding input output voltage swings coupled with offset current make these amplifiers excitation designs.
Features
Output Voltage Swing ±35V Supply Voltage ±10V ±40V Offset Current. Bandwidth 4MHz Slew Rate. 5V/µs Common Mode Input Voltage Range. ±35V Output Overload Protection
Applications
Industrial Control Systems Power Supplies High Voltage Regulators Resolver Excitation Signal Conditioning
Ordering Information
PART NUMBER HA2-2640-2 HA7-2640-2 HA2-2645-5 HA7-2645-5 PART MARKING HA2-2640-2 HA7-2640-2 HA2-2645-5 HA7-2645-5 TEMP. RANGE (oC) PACKAGE PKG. DWG.
Metal T8.C CERDIP F8.3A
Metal T8.C CERDIP F8.3A
Pinouts
HA-2640/2645 (CERDIP) VIEW HA-2640/2645 (METAL CAN) VIEW
COMP COMP
(TO-99 CASE VOLTAGE FLOATING)
CAUTION: These devices sensitive electrostatic discharge; follow proper Handling Procedures. 1-888-INTERSIL 1-888-468-3774 Intersil (and design) registered trademark Intersil Americas Inc. Copyright Intersil Americas Inc. 2001, 2004, 2006. Rights Reserved other trademarks mentioned property their respective owners.
HA-2640, HA-2645
Absolute Maximum Ratings
Voltage Between Terminals 100V Differential Input Voltage Range Output Current Full Short Circuit Protection
Thermal Information
Thermal Resistance (Typical, Note (oC/W) (oC/W) CERDIP Package. Metal Package Maximum Junction Temperature .175oC Maximum Storage Temperature Range -65oC 150oC Maximum Lead Temperature (Soldering 10s) 300oC
Operating Conditions
Temperature Range HA-2640-2 -55oC 125oC HA-2645-5 75oC
CAUTION: Stresses above those listed "Absolute Maximum Ratings" cause permanent damage device. This stress only rating operation device these other conditions above those indicated operational sections this specification implied.
NOTE: measured with component mounted evaluation board free air.
Electrical Specifications
PARAMETER INPUT CHARACTERISTICS Offset Voltage
VSUPPLY ±40V, Unless Otherwise Specified TEMP (oC) HA-2640-2 HA-2645-5 UNITS
TEST CONDITIONS
Full
µV/oC
Average Offset Voltage Drift Bias Current
Full Full
Offset Current
Full
Input Resistance (Note Common Mode Range TRANSFER CHARACTERISTICS Large Signal Voltage Gain VOUT ±30V ±20V VOUT 90mV
Full
Full
kV/V kV/V
Common Mode Rejection Ratio Minimum Stable Gain Unity Gain Bandwidth OUTPUT CHARACTERISTICS Output Voltage Swing Output Current Output Resistance Full Power Bandwidth (Note
Full
Full Open Loop VOUT ±35V VOUT ±200mV VOUT ±200mV
TRANSIENT RESPONSE 50pF, Rise Time Overshoot Slew Rate POWER SUPPLY CHARACTERISTICS Supply Current Supply Voltage Range Power Supply Rejection Ratio NOTES: This parameter based upon design calculations. Full Power Bandwidth guaranteed based upon slew rate measurement: FPBW S.R./2VPEAK; VPEAK 35V. ±10V ±40V Full Full ±2.5 V/µs
FN2904.5
HA-2640, HA-2645 Schematic Diagram
COMP VOUT
Test Circuits Waveform
COMP
VV50pF
NOTE: Tested offset adjustment range |VOS +1mV| minimum referred output. Typical range ±20mV with 10k. FIGURE SLEW RATE TRANSIENT RESPONSE TEST CIRCUIT FIGURE SUGGESTED ADJUSTMENT COMPENSATION HOOK
FN2904.5
HA-2640, HA-2645 Test Circuits Waveform
(Continued)
Vertical 10V/Div., Horizontal 5µs/Div. NOTE: 50pF, 25oC, ±40V FIGURE VOLTAGE FOLLOWER PULSE RESPONSE
Typical Performance Curves
±40V, 25oC, Unless Otherwise Specified
1000 INPUT NOISE VOLTAGE (nV/Hz) INPUT NOISE CURRENT (pA/Hz) PHASE ANGLE (DEGREES)
CURRENT (nA)
INPUT NOISE CURRENT INPUT NOISE VOLTAGE
BIAS CURRENT OFFSET CURRENT
0.01 100K
TEMPERATURE (oC)
FREQUENCY (Hz)
FIGURE INPUT BIAS OFFSET CURRENT TEMPERATURE
NORMALIZED VALUE REFERRED 25oC
FIGURE INPUT NOISE CHARACTERISTICS
OPEN LOOP VOLTAGE GAIN (dB)
GAIN
PHASE
SLEW RATE
BANDWIDTH
TEMPERATURE (oC)
100K
FREQUENCY (Hz)
FIGURE NORMALIZED PARAMETERS TEMPERATURE
FIGURE OPEN LOOP FREQUENCY RESPONSE
FN2904.5
HA-2640, HA-2645 Typical Performance Curves
NORMALIZED VALUE REFERRED ±30V OPEN LOOP GAIN (dB) CCOMP 100pF
±40V, 25oC, Unless Otherwise Specified (Continued)
SLEW RATE BANDWIDTH
300pF 1,000pF
30pF 100pF
100K
SUPPLY VOLTAGE (±V)
FREQUENCY (Hz)
FIGURE NORMALIZED PARAMETERS SUPPLY VOLTAGE 25oC
FIGURE OPEN LOOP FREQUENCY RESPONSE VARIOUS VALUES CAPACITORS FROM COMPENSATION GROUND
OUTPUT VOLTAGE SWING (VP-P) VSUPPLY ±40V VSUPPLY ±20V 10.0 VSUPPLY ±10V OUTPUT VOLTAGE
VSUPPLY ±20V +15V -55oC 25oC 125oC VSUPPLY ±40V +35V
125oC 25oC
-55oC
-55oC
125oC 25oC -55oC VSUPPLY ±20V -15V
125oC 25oC
100K FREQUENCY (Hz)
VSUPPLY ±40V -35V
OUTPUT LOAD CURRENT (mA)
FIGURE OUTPUT VOLTAGE SWING FREQUENCY
OUTPUT VOLTAGE SWING (±V) SUPPLY CURRENT (mA) -0.5 -1.0 -1.5 -2.0 -2.5 -ICC +ICC
FIGURE OUTPUT CURRENT CHARACTERISTIC
-VOUT +VOUT
SUPPLY VOLTAGE (±V)
SUPPLY VOLTAGE (±V)
FIGURE SUPPLY CURRENT SUPPLY VOLTAGE
FIGURE OUTPUT VOLTAGE SWING SUPPLY VOLTAGE
FN2904.5
HA-2640, HA-2645 Characteristics
SUBSTRATE POTENTIAL (Powered Up): Unbiased TRANSISTOR COUNT: PROCESS: HV200 Bipolar Dielectric Isolation
Metallization Mask Layout
HA-2640, HA-2645
COMP
FN2904.5
HA-2640, HA-2645 Metal Packages (Can)
REFERENCE PLANE BASE SEATING PLANE BASE METAL LEAD FINISH
T8.C MIL-STD-1835 MACY1-X8 (A1)
LEAD METAL PACKAGE INCHES SYMBOL 0.165 0.016 0.016 0.016 0.335 0.305 0.110 0.185 0.019 0.021 0.024 0.375 0.335 0.160 MILLIMETERS 4.19 0.41 0.41 0.41 8.51 7.75 2.79 4.70 0.48 0.53 0.61 9.40 8.51 4.06 NOTES Rev. 5/18/94
0.200 0.100 0.027 0.027 0.500 0.250 0.010 0.040 0.034 0.045 0.750 0.050 0.045
5.08 2.54 1.02 0.86 1.14 19.05 1.27 1.14
0.69 0.69 12.70 6.35 0.25
SECTION
NOTES: (All leads) applies between applies between 0.500 from reference plane. Diameter uncontrolled beyond 0.500 from reference plane. Measured from maximum diameter product. basic spacing from centerline terminal basic spacing each lead lead position places) from looking bottom package. maximum number terminal positions. Dimensioning tolerancing ANSI Y14.5M 1982. Controlling dimension: INCH.
FN2904.5
HA-2640, HA-2645 Ceramic Dual-In-Line Frit Seal Packages (CERDIP)
-A-DBASE METAL -Bbbb BASE PLANE SEATING PLANE SECTION LEAD FINISH
F8.3A MIL-STD-1835 GDIP1-T8 (D-4, CONFIGURATION
LEAD CERAMIC DUAL-IN-LINE FRIT SEAL PACKAGE INCHES SYMBOL 0.014 0.014 0.045 0.023 0.008 0.008 0.220 0.200 0.026 0.023 0.065 0.045 0.018 0.015 0.405 0.310 MILLIMETERS 0.36 0.36 1.14 0.58 0.20 0.20 5.59 5.08 0.66 0.58 1.65 1.14 0.46 0.38 10.29 7.87 NOTES Rev. 4/94
eA/2
eA/2
0.100 0.300 0.150 0.125 0.015 0.005 0.200 0.060 105o 0.015 0.030 0.010 0.0015
2.54 7.62 3.81 3.18 0.38 0.13 5.08 1.52 105o 0.38 0.76 0.25 0.038
NOTES: Index area: notch identification mark shall located adjacent shall located within shaded area shown. manufacturer's identification shall used identification mark. maximum limits lead dimensions shall measured centroid finished lead surfaces, when solder plate lead finish applied. Dimensions apply lead base metal only. Dimension applies lead plating finish thickness. Corner leads N/2, N/2+1) configured with partial lead paddle. this configuration dimension replaces dimension This dimension allows off-center lid, meniscus, glass overrun. Dimension shall measured from seating plane base plane. Measure dimension four corners. maximum number terminal positions. Dimensioning tolerancing ANSI Y14.5M 1982. Controlling dimension: INCH
Intersil U.S. products manufactured, assembled tested utilizing ISO9000 quality systems. Intersil Corporation's quality certifications viewed www.intersil.com/design/quality
Intersil products sold description only. Intersil Corporation reserves right make changes circuit design, software and/or specifications time without notice. Accordingly, reader cautioned verify that data sheets current before placing orders. Information furnished Intersil believed accurate reliable. However, responsibility assumed Intersil subsidiaries use; infringements patents other rights third parties which result from use. license granted implication otherwise under patent patent rights Intersil subsidiaries.
information regarding Intersil Corporation products, www.intersil.com
FN2904.5
Other recent searches
SSS7N60B - SSS7N60B SSS7N60B Datasheet
MRFE6S9135H - MRFE6S9135H MRFE6S9135H Datasheet
Privacy Policy | Disclaimer
© 2012 Datasheet Archive
