Model CV9162D Revision Engineering Date Reference Roger Janu

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

Model CV9162D Revision Engineering Date Reference Roger Janu

Datasheet Thumbnail

Top Searches for this datasheet

MODULE SPECIFICATION
Model CV9162D
Revision Engineering Date Reference
Roger January 2006 9015
ADDRESS ROOM 1006, 10/F WESTIN CENTRE, HUNG ROAD, KWUN TONG, KOWLOON, HONG KONG. (852) 2341 3238 (SALES OFFICE) (852) 2342 8228 (GENERAL OFFICE) (852) 2357 4237 (SALES OFFICE) (852) 2341 8785 (GENERAL OFFICE) E-MAIL cdl@cloverdisplay.com
http://www.cloverdisplay.com
CV9162D
MODE DISPLAY
Display mode positive negative Yellow green Grey Blue (negative) FSTN positive FSTN negative Display condition Reflective type Transflective type Transmissive type Others Viewing direction clock clock clock clock
MODULE NUMBER NOTATION:
CV9162D-
*(1)-Model number standard Modules *(2)-Backlight type backlight backlight Side-lited backlight Array backlight CCFL *(3)-Backlight color backlight Amber Blue Orange W-White Yellow green *(4)-Display mode (Negative) Yellow green Grey Blue (Negative) FSTN FSTN (Negative) *(5)-Rear polarizer type Reflective Transflective Transmissive *(6)-Temperature range Normal Extended *(7)-Viewing direction O'clock O'clock O'clock O'clock *(8)-Special code other requirements (Can omitted used)
SPEC.REV.06
PAGE
CLOVER DISPLAY LTD. GENERAL DESCRIPTION Display mode Interface Driving method Controller characters lines module 4-bit parallel 1/16 duty, bias Novatek NT7603 equivalent detailed information, please refer specifications.
CV9162D
MECHANICAL DIMENSIONS
Item Outline Dimension Viewing Area Character Size Dimension 83.0(L)x27.4(W)x2.8(H) 79.0(L)x16.1(W) 4.2(L)x6.75(W) Unit Item Character Pitch Size Dimension 4.75(L)x 7.5(W) 0.8(L)x0.8(W) Unit
CONNECTOR ASSIGNMENT
Symbol Function Power Supply Supply Voltage Power Supply Register Select Read Write Select Symbol Function Chip Enable Data Data Data Data
SPEC.REV.06
PAGE
CLOVER DISPLAY LTD. COUNTER DRAWING MODULE DIMENSION
CV9162D
SPEC.REV.06
PAGE
CLOVER DISPLAY LTD. COUNTER DRAWING BLOCK DIAGRAM
CV9162D
SPEC.REV.06
PAGE
CLOVER DISPLAY LTD. ELECTRICAL CHARACTERISTICS
Item Supply Voltage Supply Current Supply Voltage Symbol MIN. 4.75 TYP. MAX. 5.00 5.25 Unit Item "H"Level Input Voltage "L"Level Input Voltage
CV9162D
Conditions: VSS=0V, @Ta=25
Symbol MIN. TYP. MAX. Unit
0.30
0.50
0.65
0.70
Backlight Current
Backlight Voltage
Frequency 400Hz)
Side-lited
Side-lited White (current@35mA) Blue (current@35mA) Yellow Green
White Blue Yellow Green
ABSOLUTE MAXIMUM RATINGS
Please make sure exceed following maximum rating values under worst application conditions Item Supply Voltage Input Voltage Operating Temperature Storage Temperature Symbol Topr Tstg Rating (for normal temperature) -0.3 +0.3 Rating (for wide temperature) -0.3 +0.3 Unit
SPEC.REV.06
PAGE
CLOVER DISPLAY LTD. INSTRUCTIONS
CV9162D
DISPLAY CHARACTER POSITION
16x2, 1/16 DUTY CYCLE line line
DISPLAY POSITION ADDRESS
SPEC.REV.06
PAGE
CV9162D
SPEC.REV.06
PAGE
CLOVER DISPLAY LTD. ELECTRO-OPTICAL CHARACTERISTICS
MEASURING CONDITION: POWER SUPPLY TEMPERATURE RELATIVE HUMIDITY SYMBOL Toff V3:00 V6:00 V9:00 V12:00 UNIT TYP. TYP.
CV9162D
ITEM RESPONSE TIME CONTRAST RATIO VIEWING ANGLE O'clock)
ELECTRO-OPTICAL CHARACTERISTICS MEASURED VALUE GUARANTEED ONES.
RELIABILITY MODULE
ITEM High temperature operating temperature operating High temperature storage temperature storage Temperature-humidity storage Temperature cycling Vibration Test Level TEST CONDITION NORMAL TEMPERATURE 50°C 60°C -10°C 40°C R.H. -10°C 60°C Dwell Freq 10-55 Sweep rate: 10-55-10 Sweep mode Linear Displacement: Hour each TEST CONDITION WIDE TEMPERATURE 70°C -20°C 80°C -30°C 60°C R.H. -30°C 80°C Dwell Freq 10-55 Sweep rate: 10-55-10 Sweep mode Linear Displacement: Hour each TIME hours hours hours hours hours cycle
SAMPLING METHOD SAMPLING PLAN: CLASS AQL: MIL-STD 105E LEVEL SINGLE SAMPLING MAJOR-0.65% MINOR 1.5%
SPEC.REV.06
PAGE
CLOVER DISPLAY LTD. QUALITY STANDARD
DEFECT SHORT CIRCUIT MISSING SEGMENT UNEVEN POOR CONTRAST CROSS TALK HOLE EXCESS SEGMENT BUBBLES BLACKS SPOTS CRITERIA MAX(a,b) MAX(c,d) 0.3<d0.4 0.4<d LINE SCRATCHES BLACK LINE (d1,d2) x0.7 y0.05 x0.7 y0.05 APPLICABLE QTY=0 N.A.** QTY1 QTY=0 QTY=0 QTY=0 MINOR MINOR TYPE MAJOR MAJOR MAJOR MAJOR MINOR MINOR MINOR MINOR FIGURE
CV9162D
DEFECT TABLE
SPEC.REV.06
PAGE
CLOVER DISPLAY LTD. QUALITY STANDARD CONT
DEFECT CONTACT EDGE CHIPS BOTTOM GLASS CORNER GLASS GLASS PROTRUSION RAINBOW a3.0 e1/2T p1.0 CRITERIA f1/3W q3.5 g3.5 r1/2T MINOR TYPE FIGURE MINOR MINOR
CV9162D
a1.5 b1/3T c1/2W
UNLESS STATE OTHERWISE UNIT MILLIMETER
DEFECT TABLE
SPEC.REV.06
PAGE
CLOVER DISPLAY LTD. HANDLING PRECAUTIONS
CAUTION HANDLING CLEANING soft cloth with solvent (recommended below) clean display surface wipe lightly. Isopropyl alcohol, ethyl alcohol, trichlorotriflorothane
CV9162D
wipe display surface with hard materials that will damage polarizer surface. following solvent; -water, ketone, aromatics CAUTION AGAINST STATIC CHARGE modules CMOS drivers, customers recommend that unused input terminal would connected input signals before power turned ground your body, work/assembly areas, assembly equipment protect against static electricity. Remove protective film slowly and, possible, under control device like blower humidity working room should kept over 50%RH reduce risk static charge. PACKAGING Avoid intense shock falls from height operate store them exposed direct sunshine high temperature/humidity. CAUTION OPERATION indispensable condition drive LCD's within specified voltage limit since higher voltage than limit causes shorter life. direct current drive should avoided because electrochemical reaction direct current causes LCD's undesirable deterioration. Response time will extremely delayed temperature, LCD's show dark color high temperature. However those phenomena mean malfunction order with LCD's. Some font will abnormally displayed when display area pushed hard during operation. resumes normal condition after turning once. SOLDERING (for type) recommended complete soldering hand soldering within seconds. soldering position least apart from head. Wave reflow soldering recommended. Metal pins should soldered more than times each soldering should done after cool down metal pins SAFETY crash damaged unnecessary LCD's, recommended wash liquid crystal either solvents such acetone ethanol should burned later. When liquid leaked damaged glass cell comes contact with your hands, wash with soap water. WARRANTY CLOVER will replace repair module accordance with specification period year from date shipment. warranty liability Clover limited repair and/or replacement. Clover will responsible subsequent consequential event.
SPEC.REV.06
PAGE

Model CV9162D Revision Engineering Date Reference Roger Janu

Top Searches for this datasheet

Other recent searches