signal shield IN4) remark connected GND, when shielded cable used posi
|
|
|
Top Searches for this datasheet
PIN-array 3-phase bridge driver SKiiPPACK type ,,GD GDL"
signal shield IN4) remark connected GND, when shielded cable used positive CMOS logic; impedance X10: halfbridge (HB1) Signal Collector 1=TOP (HB1) Gate 1=TOP (HB1) Emitter 1=TOP (HB1) Collector 2=BOT (HB1) Gate 2=BOT (HB1) Emitter 2=BOT (HB1)
ERROR short circuit monitoring ERROR; open collector output; max. propagation delay min. pulsewidth error-memory-reset IN4) IN4) positive CMOS logic; impedance positive CMOS logic; impedance
ERROR short circuit monitoring ERROR; open collector output; max. propagation delay min. pulsewidth error-memory-reset IN4) IN4) ERROR
positive CMOS logic; impedance positive CMOS logic; impedance short circuit monitoring ERROR; open collector output; max. propagation delay min. pulsewidth error-memory-reset positive CMOS logic; impedance ERROR open collector Output; max. ,,low" output voltage ,,high" output voltage max. when using option ,,U" actual DC-link voltage, refer UDCmax max. output current supply with when using supply voltage monitoring threshold 15,6 power supply supply with when using VDCIN supply voltage monitoring threshold power supply digital signals
X11: halfbridge (HB2) Signal Temp.-Sensor (HB2)1 Temp.-Sensor (HB2)2 Collector 1=TOP (HB2) Gate 1=TOP (HB2) Emitter 1=TOP (HB2) Collector 2=BOT (HB2) Gate 2=BOT (HB2) Emitter 2=BOT (HB2)
Overtemp.
reserved analog
Temp. analog aux2) analog
X12: halfbridge (HB3) Signal Collector 1=TOP (HB3) Gate 1=TOP (HB3) Emitter 1=TOP (HB3) Collector 2=BOT (HB3) Gate 2=BOT (HB3) Emitter 2=BOT (HB3)
current actual value, refer overcurrent trip level current value SKiiP source current value SKiiP sink current actual value, refer overcurrent trip level current value SKiiP source current value SKiiP sink current actual value, refer overcurrent trip level current value SKiiP source current value SKiiP sink
aux2) analog
analog
Open collector output, external pull resistor necessary reference analog output signals ,,high" (min) 11,2 ,,low" (max)
B7-8
0898 0796
SEMIKRON
PIN-array brake chopper driver (used SKiiPPACK type GDL)
signal shield CHOPPER ext. remark connected GND, when shielded cable used IGBT ,,low" (max) Imin ,,high" (min) 11,5 propagation delay td(on) td(off) ERROR open collector Output; max. propagation delay tPD(on)error RESET Reset-pulse-time tPDRESET connect this open collector output without pull resistor ,,low" (max) ,,high" (min) supply with when using DCIN supply voltage monitoring threshold 15,6 supply with when using DCIN supply voltage monitoring threshold
ERROR OUT1)
RESET
reserved reserved reserved reserved
X13: halfbridge (HB4) Signal remark Temp.-sensor Temp.-sensor Collector 1=TOP (HB4) monitoring Gate 1=TOP (HB4) Emitter 1=TOP (HB4) Collector 2=BOT (HB4) Gate 2=BOT (HB4) Emitter 2=BOT (HB4) connected with connected with
Open collector output, external pull resistor necessary
SEMIKRON
0898 0796
B7-9
Other recent searches
SP6121 - SP6121 SP6121 Datasheet
PE-50 - PE-50 PE-50 Datasheet
ISL54200 - ISL54200 ISL54200 Datasheet
ISL28278 - ISL28278 ISL28278 Datasheet
ISL28478 - ISL28478 ISL28478 Datasheet
GT10J301 - GT10J301 GT10J301 Datasheet
FDS6690AS - FDS6690AS FDS6690AS Datasheet
EDIk51-3 - EDIk51-3 EDIk51-3 Datasheet
ADG774 - ADG774 ADG774 Datasheet
Privacy Policy | Disclaimer
© 2012 Datasheet Archive
