Avago's AMMP-6522 easy-to-use broadband includes 3-stage provide gain
|
|
|
Top Searches for this datasheet
AMMP-6522 GaAs MMIC LNA/IRM Receiver Package
Avago's AMMP-6522 easy-to-use broadband includes 3-stage provide gain amplification gate-pumped image-reject mixer frequency translation. overall receiver performs Single Side Band down-conversion signal range.The matched 50.The output provided 2-port format where external using PHEMT technology. surface mount package allows elimination of"chip wire" assembly lower cost.This MMIC cost effective alternative
Features
5x5mmSurfaceMountPackage
IntegratedLowNoiseAmplifier IntegratedImageRejectMixer 50InputandOutputMatch SingleSupplyBiasPin
Specifications mA), -1.0 (0.1
RFfrequency:7to20GHz IFfrequency:DCto3.5GHz ConversionGain(RF/IF):13dB InputInterceptPoint:-4dBm ImageSuppression:15dB TotalNoiseFigure:2.4dB
Connections (Top View)
FUNCTION
Application
Microwaveradiosystems SatelliteVSAT,DBSUp/DownLink LMDS&Pt-PtmmWLongHaul 802.20WiMax) WLLandMMDSloops Commercialgrademilitary
VIEW PACKAGE BASE:
electrostaticsensitivedevices. ESDMachineModel(ClassA) ESDHumanBodyModel(Class1A) A004R: Electrostatic Discharge, Damage Control. Notes: devices.
Absolute Maximum Ratings[1]
Symbol
Tstg Tmax
Parameter Test Condition
DraintoGroundVoltage GatetoGroundVoltage DrainCurrent GateCurrent RFCWInputPowerMax Maxchanneltemperature Storagetemperature MaximumAssemblyTemp
Unit
Max.
+0.8 +150 -65+150 260for20s
Note:
Specifications/ Physical Properties[2]
Symbol
Parameter Test Condition
DrainSupplyVoltage DrainSupplyCurrent(Vd=4.0V) GateSupplyVoltage(Ig=0.1mA) ThermalResistance(3)
Unit
Min.
-1.2
Typ.
-1.0
Max.
-0.8
Operating Conditions
Symbol
RFfreq LOfreq IFfreq
Parameter Test Condition
RFFrequency LOFrequency IFFrequency LODrivePower
Units
Min.
DC[8]
Typ.
Max.
Specifications[4,5,6]
Symbol
IIP3
Parameter
NoiseFigure ConversionGain InputThirdOrderIntercept ImageRejection
Freq (GHz)
RF=8GHz,LO=10GHz RF=18GHz,LO=20GHz RF=8GHz,LO=10GHz RF=18GHz,LO=20GHz RF=8GHz,LO=10GHz RF=18GHz,LO=20GHz RF=8GHz,LO=10GHz RF=18GHz,LO=20GHz
Units
-0.4
RF=8GHz: RF=18GHz:
AMMP-6522 Typical Performance[1,2]
LOPower=+15dBmunlessnoted)
NOISE FIGURE (dB)
CONV GAIN (dB)
FREQUENCY (GHz)
FREQUENCY (GHz)
Figure Receiver conversion gain
Figure Typical noise figure
RETURN LOSS (dB)
IIP3 (dBm)
FREQUENCY (GHz)
FREQUENCY (GHz)
Figure Return loss ports
Figure Typical input
CONV GAIN (dB) IIP3 (dBm)
POWER (dBm)
POWER (dBm)
Figure Conv gain power GHz)
Figure Input power GHz)
CONV GAIN (dB) IIP3 (dBm)
FREQUENCY (GHz)
FREQUENCY (GHz)
Figure conversion gain frequencies
Figure Input frequencies
AMMP-6522 Typical Performance (cont.)[1,2]
unlessnoted)
INPUT (dBm) CONV GAIN (dB) -1.2 -1.1 -1.0 -0.9
-1.2 -1.1 -1.0 -0.9
FREQUENCY (GHz)
FREQUENCY (GHz)
Figure Conversion gain over
Figure Input over
NOISE FIGURE (dB)
CONV GAIN (dB)
FREQUENCY (GHz)
FREQUENCY (GHz)
Figure Receiver conversion gain over
Figure Noise figure over
RETURN LOSS (dB)
IIP3 (dBm) 25°C -40°C 85°C FREQUENCY (GHz)
FREQUENCY (GHz)
Figure Return loss over temperature
25°C -40°C 85°C
Figure Input over
NOISE FIGURE (dB) 25°C -40°C 85°C
RETURN LOSS (dB)
FREQUENCY (GHz)
FREQUENCY (GHz)
Figure Return loss over temperature
Figure Noise figure over temperature
Notes: de-embededfromthedata.
AMMP-6522 Application Usage
Biasing Operation AMMP-6522 normally biased with positive gate voltage connected through bypass capacitors shown Figure recommended corresponding currents should come from noise driver ensure that overallFrontEndNFislow. image rejection performance dependent frontendperformance. There minimal performance degradation then will provide considerably similar performance. recommendedVg -1V. However, depending better performance that particular frequency. phenomenon DC-offset could occur outputs. most practical applications, should more DCandthermalcondition.
1000 1-3.5
1000
VIEW PACKAGE BASE:
Figure Application receiver with Balun
(-IF) (IF) (IF)
LSB: (IF) (IF) USB: (IF) (IF)
(LO)
LSB: (IF) (IF) (-IF) (IF) (IF) USB: (IF) (IF)
USING: ignoring terms
WHEN DELAYED DEGREES:
Figure Theory harmonic rejection
Figure Evaluation/test board
IN-PHASE DIVIDER DEGREE HYBRID
90-DEGREE HYBRID
EXTERNAL
Figure Simplified with Receiver Schematic (the quadrature hybrid external circuit)
Recommended Attachment Package
material mounting pattern, defined recommended. electronic drawing land pattern available upon request from Agilent Sales ApplicationEngineering.
Figure Suggested Land Pattern Stencil Layout
Figure Stencil Outline Drawing (mm)
Figure Combined Stencil Layouts (mm)
Manual Assembly Recommended attachment conductive solder Neither Conductive epoxy hand soldering recommended. component layout should performance. Follow solder paste vendor's recommendations when developing solder reflow profile. standard pre-heat temp. avoid damage thermalshock.
TEMPERATURE (°C) RAMP PREHEAT RAMP TIME (SECONDS) REFLOW COOLING PEAK MELTING POINT 218°C
opening approximately pad. Reducing stencil opening potentially steel which capable producing required fine stenciloutline. most commonly used solder reflow method accomplished belt furnace using convection heat transfer. suggested reflow profile automated reflow processes shown Figure This profile profile indicated Figure will vary among different hereforreferenceonly.
Figure Suggested lead-free Reflow Profile SnAgCu solder paste
Package Dimensions
0.011 (0.28)
0.114 (2.90) 0.018 (0.46)
0.014 (0.365)
0.200 (5.08)
AMMP XXXX 043101
0.200 (5.08)
0.016 (0.40)
0.126 (3.2)
0.059 (1.5)
0.100 (2.54) 0.029 (0.75) 0.016 (0.40) 0.075 (1.91)
0.012 (0.30)
0.028 (0.70) 0.100 (2.54) 0.93 (2.36)
VIEW
NOTES: ALLGROUNDSMUSTBESOLDEREDTOPCBRF
SIDE VIEW
BACK VIEW
DIMENSIONS INCHES (MILLIMETERS) DIMENSIONAL TOLERANCE: 0.002" (0.05
Carrier Tape Pocket Dimensions
AMMP XXXX AMMP XXXX AMMP XXXX
4.00 0.10 NOTE 2.00 0.05 1.55 0.05 0.50 TYP. 1.75 0.10 5.50 0.05 SECTION PITCH: WIDTH: 5.30 5.30 2.20 8.00 12.00 MIN. 5.20 NOM. 5.30 MAX. 5.40 5.20 5.30 5.40 2.10 2.20 2.30 12.00 0.10
8.00 0.10
1.50 (MIN.)
0.30 0.05 SECTION NOTES: MEASURED ABOVE BASE POCKET. PITCHES CUMULATIVE TOLERANCE DIMENSIONS MILLIMETERS (mm).
AMMP-6522 Part Number Ordering Information
Part Number AMMP-6522-BLKG AMMP-6522-TR1G AMMP-6522-TR2G Devices Container Container Antistatic Reel Reel
product information complete list distributors, please website:
www.avagotech.com
Avago, Avago Technologies, logo trademarks Avago Technologies Limited United States other countries. Data subject change. Copyright 2007 Avago Technologies Limited. rights reserved. AV02-0244EN June 2007
Other recent searches
W934GO - W934GO W934GO Datasheet
2SRD - 2SRD 2SRD Datasheet
SD215UF500X60 - SD215UF500X60 SD215UF500X60 Datasheet
RJK1555DPA - RJK1555DPA RJK1555DPA Datasheet
NJG1551F - NJG1551F NJG1551F Datasheet
LSP3312 - LSP3312 LSP3312 Datasheet
IBM39MPEGS42x - IBM39MPEGS42x IBM39MPEGS42x Datasheet
IBM39MPEGSI - IBM39MPEGSI IBM39MPEGSI Datasheet
2SA1671 - 2SA1671 2SA1671 Datasheet
1SS405 - 1SS405 1SS405 Datasheet
Privacy Policy | Disclaimer
© 2012 Datasheet Archive
