2000/9/6 2001/1/5 2001/1/11 Release Modify timing characteristic. Modi

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

2000/9/6 2001/1/5 2001/1/11 Release Modify timing characteristic. Modi

Datasheet Thumbnail

Top Searches for this datasheet

2000/9/6 2001/1/5 2001/1/11 Release Modify timing characteristic. Modify Optical Characteristics
(1)Display format dots, 1/128 duty. (2)Construction panel COF. (3)Display type FSTN Transflective, Positive o'clock view (4)Controller HD66750 (5)+3.0V single power input. (6)Extend temperature type.
size pitch Viewing area Module size
0.185(W) 0.21(H) 0.195(W) 0.22(H) 28.17(W) 36.07(W) 81.57(H) max.(T)
#!&!!'
Logic Circuit Supply Voltage Driving Voltage Input Voltage Extend temp. type Operating Temp. Storage Temp. VDD-VSS VLCD-VSS -0.3 -0.3
+4.6 20.0 VDD+0.3
#)*#"
Logic Circuit Supply Voltage Driving Voltage (FSTN VDD-VSS VLCD-VSS Input Voltage Logic Supply Current Contrast Rise Time Fall Time Viewing Angle Range -VDD 3.3V 13.3 12.35 12.15 11.7 11.6 0.7V -0.3 13.8 12.85 12.65 12.2 12.1 -0.2
14.3 13.35 13.15 12.7 12.6 0.15
Frame Frequency 25°C 25°C 25°C 25°C 25°C -10.2 Deg. Note Note Note
(NOTE Contrast ratio (Brightness state) (Brightness state)
NOTE Response time
(NOTE Viewing angle
%#,'!
D7~D0 /RES Data
Power supply logic circuit Reset .Initializes when Chip select Select register Data Write Data Read Ground (0V) Lo:Index/status Hi:Control
)*%&+%, cycle time level plusw width Hi-level pulse width PWHR Enable rise/fall time Address set-up time (RS, Address hold time Write Data set-up time Write Data hold time Read Data delay time Read Data hold time
)+%,-%.
-300
-200
/#0#%#0
Tests should conducted under following conditions Ambient temperature Humidity
Sampling method shall accordance with MIL-STD-105E level normal single sampling plan
major defect defined that could cause failure materially reduce usability unit intended purpose. minor defect that does materially reduce usability unit intended purpose infringement from established standards significant bearing effective operation.
appearance test should conducted human sight approximately distance from module under flourescent light. inspection area panel shall within range following limits.
!#$/ Function Dimension Black spots Short circuit Pattern Deviation from drawings area area Disregard D0.2 0.2<D0.3 0.3<D0.4 0.4<D Width Length disregard W0.03 0.03<W0.05 0.05<W0.07 L3.0 line criteria Average diameter Rainbow color newton ring. Obvious visible damage. note note note Major Major Minor
0.65
Black lines
Minor
Bubbles polarizer Color uniformity Glass Scratches Contrast ratio Response time Viewing angle
Minor Minor Minor Minor Minor Minor
Zone active area Zone viewing area
High Temperature Operation Temperature Operation High Temperature Storage Temperature Storage Thermal Shock Test Humidity Test Extend Temp. type 70±3°C t=96 -20±3°C t=96 80±3°C t=96 -30±3°C t=96 -30°C 25°C 80°C min. min. cycle Total cycle Humidity 90%,
Sweep frequency Hz/1min Amplitude 0.75mm Vibration Test (Packing) Test direction X.Y.Z/3 axis Duration 30min/each axis Note Condensation water permitted module. Note module should inspected after hour storage normal conditions (15-35°C 45-65%RH). Definitions life point Current drain should smaller than specific value. Function module should maintained. Appearance display quality should have degraded noticeably. Contrast ratio should greater than initial value.
"#'*
(1)A module fragile item should subjected strong mechanical shocks. (2)Avoid applying pressure module surface. This will distort glass cause change color. (3)Under circumstances should position bezel tabs their shape modified. (4)Do modify display either shape positioning components. (5)Do modify move location zebra heat seal connectors. (6)The device should only soldered during interfacing. Modification other areas board should carried out. (7)In event breakage resultant leakage fluid inhale, ingest make contact with skin. contact made rinse immediately. (8)When cleaning module soft damp cloth with mild solvent, such Isopropyl Ethyl alcohol. water, ketone aromatic permitted. (9)Prior initial power input signals should applied. (10)Protect module against static electricity observe appropriate anti-static precautions.

2000/9/6 2001/1/5 2001/1/11 Release Modify timing characteristic. Modi

Top Searches for this datasheet

Other recent searches