OSRAM GmbH Hellabrunner Str. D-81536 Munich Tel.: 6213 Fax: 6213 2020

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

OSRAM GmbH Hellabrunner Str. D-81536 Munich Tel.: 6213 Fax: 6213 2020

Datasheet Thumbnail

Top Searches for this datasheet

Installation operating instructions: Radio-control light sensor Type: DALI ADVANCED
OSRAM GmbH Hellabrunner Str. D-81536 Munich Tel.: 6213 Fax: 6213 2020 Customer Service Center (KSC) Germany Albert-Schweitzer-Str. D-81735 Munich Tel.: 1803 Fax: 1803 www.osram.com
Function overview.Page Activating sensor/inserting batteries .Page Programming ADVANCED central unit .Page Installation.Page Lighting control/setpoint adjustment .Page Notes radio operation .Page Technical data .Page
Page
Installation instructions: Light Sensor DALI ADVANCED
Function overview
radio-control light sensor transmits brightness values DALI central unit DALI ADVANCED lighting control system. often sensor sends values will depend often brightness detection area changes. sensor detects luminance particular detection area forwards this brightness value (actual value) central unit. This actual value compared with setpoint value stored central unit. central unit then uses this comparison control lighting. light sensor consists following: Base plate Brightness sensor Abb.
Activating sensor/inserting batteries
Battery type: light sensor operated with lithium button cell (type 2450N). battery included with sensor. avoid damaging electronics through electrostatic discharge, must comply with safety precautions electrostatically sensitive devices when changing battery. Inserting (replacing) battery Detach light sensor from base plate turning unit approx. anticlockwise (Fig. there battery sensor: Remove this battery. need wait about minutes before inserting battery allow capacitor discharge. Insert battery shown Fig. battery should make contact with side contact battery holder. Push battery gently until clicks place. Make sure battery right round visible when inserted). Make sure there grease battery. When battery inserted, light sensor spends first seconds sending special programming telegrams that identified system. will flash during this process.
Abb.
Abb.
Installation instructions: Light Sensor DALI ADVANCED
Page
Flat battery indicator: integrated light sensor (Fig. only seen darkness. flashes about three times whenever transmission made. flashes about times, this indicates that battery almost flat (LowBatt) replaced. Important: Keep batteries away from children. battery swallowed, seek medical attention immediately. Replace battery with same type. battery should removed immediately disposed properly.
Programming ADVANCED central unit
light sensor must trained lighting control central unit that central unit identify sensor part system. actual function sensor assigned central unit manual programming unit (MPU) also operating instructions manual programming unit. light sensor only assigned group lighting control system. maximum eight light sensors combined sensors integrated system. Procedure Remove battery from light sensor (allow enough time capacitor discharge). manual programming unit (MPU), start "radio startup" programming mode. Insert battery again. light sensor will transmit special programming telegrams approx. seconds, which manual programming unit will react ("light sensor found"). MPU, enter number luminaire group controlled this sensor. Terminate radio startup procedure MPU. This completes programming process. Notes: When enter group message "programming." will appear. This message does disappear until light sensor stops sending programming telegrams seconds after battery been inserted). During this time, other functions performed system. recommend that label light sensor with device number indicated enter this number documentation lighting system. Deleting sensor DALI ADVANCED central unit Trained devices deleted programming unit. operating instructions manual
Page
Installation instructions: Light Sensor DALI ADVANCED
Installation
Electrical equipment only installed qualified electricians. light sensor installed ceiling above illuminated work area (Fig. Make sure sensor exposed direct light. Note attach light sensor base plate until have inserted battery trained sensor central unit. Installation: Detach light sensor from base plate turning unit approx. anticlockwise. Install base plate directly ceiling using screw provided (Fig. adhesive pad. Turn light sensor clockwise through more than base plate until clicks into place. Abb. Abb.
improve radio transmission, thread antenna casing. this, puncture antenna opening (Fig. carefully with screwdriver push antenna through hole before installing base plate. strip antenna shorten
Installation instructions: Light Sensor DALI ADVANCED
Page
Lighting control/setpoint adjustment
already mentioned, group assigned light sensor when trained ADVANCED central unit. luminaires this group will then controlled sensor. This group must also assigned least channel button wall-mounted hand-held transmitter operating lighting controls. Train relevant channel button using manual programming unit then assign this button group controlled ("control group XX", operating instructions manual programming unit). Setting brightness setpoint Abb.
luminance measured light sensor (Fig. comprises reflected artificial light (Fig. daylight (Fig. depends reflective properties surface (Fig. F4). transmitted brightness value regular intervals central unit evaluation. setpoint changed, this brightness value stored central unit setpoint lighting control. Changing setpoint: Select "Regulation" "Lighting Control" menu manual programming unit. Enter number group controlled. change setpoint. Adjust lighting required setting select "Change Setpoint". message "waiting brightness value." will appear. next brightness value that light sensor sends stored setpoint central unit ("Setpoint changed"). This process take seconds. Activate lighting control switching "Regulation" option "ON". Note: long there radio link between central unit, lighting regulation will carried out. Lighting control Lighting control active relevant group been switched because trained channel button wall-mounted hand-held transmitter been pressed (short press). lighting system switched brightness then adjusted setpoint stored central unit. measured brightness value exceeds current brightness setpoint minimum dimmer setting luminaires, relevant group automatically switched off. lighting system automatically switched again. Terminating control regulated group adjusted (faded down) using trained channel buttons wall-mounted hand-held transmitter, lighting control terminated lighting value manually retained. same applies when lighting scene involving regulated group selected. restart lighting control, need switch group again using appropriate trained channel button.
Page
Installation instructions: Light Sensor DALI ADVANCED
Notes radio operation
non-exclusive transmission path used radio transmission, which means that interference cannot ruled out. Radio transmission suitable safety applications, such emergency shutdown calls emergency services. range transmitter open) depends nature building: material Wood, plaster, plasterboard Brick, Reinforced concrete Metal, metal grating, aluminium cladding Penetration approx. approx. approx. approx.
Notes radio operation This radio system only connected other communication networks this does infringe relevant national laws. This radio system used communicating beyond property boundaries. operated Germany, regulations contained Official Bulletin 73/2000 must met.
used specified, this device complies with requirements R&TTE directive (1999/5/EU). complete conformity declaration found internet www.osram.com light sensor operated EFTA states.
Installation instructions: Light Sensor DALI ADVANCED
Page
Battery:
Technical data
lithium cell 2450N
Power supply:
Transmission frequency: 433.42 MHz, Range: Coding: Type protection: Temperature range: Relative humidity: Brightness: Dimensions max. open) billion possibilities max. condensation) approx. 2000
Date 13.09.02 Light Sensor ADVANCED Version
Subject change without notice. Errors omission excepted.
Page
Installation instructions: Light Sensor DALI ADVANCED

OSRAM GmbH Hellabrunner Str. D-81536 Munich Tel.: 6213 Fax: 6213 2020

Top Searches for this datasheet

Other recent searches