E3X-DA-N Ultimate Fiber Amplifier Maximum Ease High Performance

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

E3X-DA-N Ultimate Fiber Amplifier Maximum Ease High Performance

Datasheet Thumbnail

Top Searches for this datasheet

Digital Fiber Amplifier
E3X-DA-N
Ultimate Fiber Amplifier Maximum Ease High Performance
sure read Safety Precautions page
UL991*
certification including testing evaluation Applicable standards: 3121-1 Additional application testing evaluations standards: SEMI S2-0200S
Features
Models with Connector System Reduces Wiring, Saves Space, Makes Maintenance Easier
First Industry Patent Pending Amplifiers with wire-saving connectors, power supply distributed 1-conductor slave connectors through 3conductor master connector. This design three major advantages. Wiring time significantly reduced. Relay connectors unnecessary, wiring takes less space costs reduced. Storage maintenance simpler because isn't necessary distinguish between master connector slave connectors Amplifier.
Super Digital Display with Auto Power Control (APC) Circuit
First Industry passage time causes intensity Sensor's lightemitting elements deteriorate, which make stable detection impossible. E3X-DA-N first series Fiber Sensors Auto Power Control (APC) circuit. This achieves strict detection eliminating fluctuation digital value ideal subtle detection such stable detection liquidcrystal glass.
Incident level
3000
Simplified Connector Design
Amplifiers connected.
Previous Digital Fiber Amplifiers
Threshold Unstable detection
Time Incident level
3000
Optical communications
E3X-DA-N Series
Threshold Stable detection
Power supply Slave connector
Master connector
Time
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2007 Rights Reserved.
E3X-DA-N
Power Consumption Reduced Much
Power consumption reduced much from 1800 (when digital display OFF).
Digital Display Turned Dimmed during Operation Eco-mode
When digital display viewed infrequently during operation, current consumption reduced dimming display turning entirely. (Eco-mode from Mobile Console only.)
1800
Previous model
This eco-label displayed products that meet environmental standards established OMRON.
E3X-DA-N (with digital display OFF)
Generation Mobile Consoles Size Cellular Phones. Further Developing Ultimate Power Fiber Amplifiers.
Remote Setting Adjustment
Perform settings, teaching, fine adjustments Fiber Unit.
Previously, settings teaching could performed only Amplifier. Now, however, using Mobile Console enables these operations fiber. Strict adjustments made while checking workpiece position.
With group teaching, teach multiple amplifiers simultaneously.
tedious teaching that performed separately each Amplifier performed several Amplifiers once using Mobile Console.
Group teaching
Eliminate inconsistency using group zero reset.
group zero reset function simultaneously reset digital displays multiple Amplifiers This function useful minimize variation between Amplifier values.
Display light intensity threshold same time.
Concept
Patent Pending
Flash Sensor head display amplifier channels during operation.
Function indicator section Channel setting section Light intensity monitor
Channel
Even Amplifier Sensor head separated during operation, still possible flash Sensor head display amplifier channels.
Threshold
Channel Channel Channel Channel
Operation keys
Battery monitor Head
Optical communications
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2007 Rights Reserved.
E3X-DA-N
Ordering Information
Amplifiers
Pre-wired Amplifiers
Type Standard models Monitor-output models Mark-detecting models (blue LED) Mark-detecting models (green LED) Infrared models Differential-output model* Appearance Control output ON/OFF output ON/OFF output Monitor output Model output E3X-DA11-N E3X-DA21-N E3X-DAB11-N E3X-DAG11-N E3X-DAH11-N E3X-DA11D output E3X-DA41-N E3X-DA51-N E3X-DAB41-N E3X-DAG41-N E3X-DAH41-N
Water-resistant models ON/OFF output
E3X-DA11V
E3X-DA41V
Twin-output models
E3X-DA11TW
E3X-DA41TW
details, refer page
Amplifiers with Standard Connectors
Type Standard models Monitor-output models Mark-detecting models (Blue LED) Mark-detecting models (Green LED) Infrared models Differential-output model* Appearance Applicable Connector (order separately) Master Slave Master Slave Master Slave Master Slave Master Slave Master Slave E3X-CN11 E3X-CN12 E3X-CN21 E3X-CN22 E3X-CN11 E3X-CN12 E3X-CN11 E3X-CN12 E3X-CN11 E3X-CN12 E3X-CN11 E3X-CN12 Control output ON/OFF output ON/OFF output Monitor output Model output E3X-DA6 E3X-DA7 E3X-DAB6 E3X-DAG6 E3X-DAH6 E3X-DA6D output E3X-DA8 E3X-DA9 E3X-DAB8 E3X-DAG8 E3X-DAH8
Water-resistant models connector)
XS3F-M421-40@-A XS3F-M422-40@-A
ON/OFF output E3X-DA14V E3X-DA44V
Master Twin-output models Slave
details, refer page
E3X-CN21 E3X-DA6TW E3X-CN22 E3X-DA8TW
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2007 Rights Reserved.
E3X-DA-N
Amplifier Connectors (Order Separately) Note: Seal provided accessory.
Type Master Connector Slave Connector E3X-CN12 E3X-CN22 Appearance Cable length conductors Model E3X-CN11 E3X-CN21
Combining Amplifiers Connectors (Basically Amplifiers Connectors sold separately.)
Refer following tables when placing order.
Amplifiers E3X-DA6 E3X-DAB6 Mark-detecting models E3X-DAG6 Infrared models E3X-DAH6 Differential-output model E3X-DA6D Monitor-output models E3X-DA7 Twin-output models E3X-DA6TW Type Standard models E3X-DA8 E3X-DAB8 E3X-DAG8 E3X-DAH8 -E3X-DA9 E3X-DA8TW
Applicable Connectors (Order Separately) Master Connector Slave Connector
E3X-CN11
E3X-CN12
E3X-CN21
E3X-CN22
When Using Amplifiers
Amplifiers Units) Master Connector Slave Connectors
Sensor Connectors (Order Separately)
Size Cable specifications Appearance Standard cable Cable type Model XS3F-M421-402-A 4-wire connection XS3F-M421-405-A XS3F-M422-402-A XS3F-M422-405-A
Straight connector L-shaped connector
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2007 Rights Reserved.
E3X-DA-N
Mobile Console (Order Separately)
Appearance Model Remarks
Mobile Console with head, cable, (model number set) adapter provided accessories. E3X-MC11 Power supply method: chargeable battery
E3X-MC11-C1
Mobile Console
E3X-MC11-H1
Head
E39-Z12-1
Cable (1.5
Accessories (Order Separately)
Mounting Brackets
Appearance Applicable model E3X-DA-N Series Model E39-L143 E3X-DA@V E39-L148 -Quantity Remarks
Operating Instructions Sticker
Model E39-Y1 Remarks Attach near Sensor. Refer page
Plate
Appearance Model PFP-M Quantity
When using Through-beam Fiber Unit, order Bracket Receiver Emitter.
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2007 Rights Reserved.
E3X-DA-N
Ratings Specifications
Amplifiers
Pre-wired Amplifiers
Type Output type Item Light source (wavelength) Power supply voltage Power consumption output output Standard models -DA11-N -DA41-N (660 Monitoroutput models -DA21-N -DA51-N Mark-detecting models -DAB11-N -DAB41-N Blue (470 -DAG11-N -DAG41-N Green (525 Infrared models -DAH11-N -DAH41-N Infrared (870 Waterresistant models -DA11V -DA41V (660 Twin-output models -DA11TW -DA41TW dimensions, refer page
VDC±10%, ripple (p-p) max. Normally: max. (current consumption: max. power supply voltage VDC) Mode: max. (current consumption: max. power supply voltage VDC) Digital display lit: max. (current consumption: max. power supply voltage VDC) Load current: (residual voltage (NPN/PNP): max., Open collector (NPN output, depending model) Light ON/Dark selectable -Load VDC, min.
Control output
ON/OFF output Monitor output
Protection circuit
Power supply reverse polarity, Output short-circuit protection, Mutual interference prevention (supported Units) operation reset respectively operation reset operation reset respectively
Super-highspeed mode ReStandard sponse mode time Super-longdistance mode Sensitivity setting Timer function Automatic power control (APC) Functions Zero-reset Initial reset
0.25 operation reset respectively
operation reset respectively
operation reset respectively
Teaching manual method OFF-delay timer: (set 1-ms units); (set 5-ms units) Using Mobile Console: delay, delay, shot (selectable) Fiber-optic current digital control Negative values displayed. Settings returned defaults required. Upper lower limits required every digital values. -Fiber-optic current digital control
Monitor focus
Indicators Display timing Display orientation Optical axis adjustment Ambient illumination (receiver side)
Operation indicator (orange), 7-segment digital incident level display (red), 7-segment digital incident level percentage display (red), threshold excess gain 2-color double indicators (green red), 7-segment digital threshold display (red) Switching between normal/peak-hold/bottom-hold possible Switching between normal/reverse possible Optical axis adjustment possible (hyper-flashing function) Incandescent lamp: 10,000 max. Sunlight: 20,000 max.
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2007 Rights Reserved.
E3X-DA-N
Standard models -DA11-N -DA41-N Monitoroutput models -DA21-N -DA51-N Infrared models -DAH11-N -DAH41-N Waterresistant models -DA11V -DA41V Twin-output models -DA11TW -DA41TW
Type Output type Item output output
Mark-detecting models -DAB11-N -DAB41-N -DAG11-N -DAG41-N
Ambient temperature
Operating:Groups Amplifiers: 55°C Groups Amplifiers: 50°C Groups Amplifiers: 45°C Storage:-30 70°C (with icing condensation) Operating storage: (with condensation) min. VDC) 1,000 50/60 with 1.5-mm double amplitude each directions 500m/s2, times each directions IP66 (with Protective Cover attached) Approx. IP50 (with Protective Cover attached) Approx. Polyethersulfo
Ambient humidity Insulation resistance Dielectric strength Vibration resistance (destruction) Shock resistance (destruction)
Degree protection
IP50 (with Protective Cover attached)
Connection method Weight (packed state) Material Case Cover
Pre-wired (standard cable length: Approx. Polybutylene terephthalate (PBT) Polycarbonate Instruction sheet
Accessories
Amplifiers with Connectors (Specifications different those Pre-wired Amplifiers)
Type Output type Item output output Standard models E3X-DA6 E3X-DA8 Monitor-output models E3X-DA7 E3X-DA9 Mark-detecting models Infrared models E3X-DAH6 E3X-DAH8 Waterresistant models* -DA14V -DA44V connector Approx. Twin-output models -DA6TW -DA8TW Standard connector Approx.
E3X-DAB6 E3X-DAB8
E3X-DAG6 E3X-DAG8
Connection method Weight (packed state)
Standard connector Approx.
dielectric strength water-resistant models 50/60 min.
Connectors
Item Rated current Rated voltage Contact resistance
Mobile Console
Model
max. mVDC max., max.) figure connection Amplifier adjacent Connector. does include conductor resistance cable. times figure number insertions connection Amplifier adjacent Connector. Polybutylene terephthalate (PBT) Phosphor bronze/gold-plated nickel Approx. Approx. E3X-CN11/21/22 E3X-CN12 Item
Model
E3X-MC11 Charged with adapter Connected adapter Approx. (Console only:
Power supply voltage Connection method Weight (packed state)
insertions (durability) Material Housing Contacts
Refer Instruction Manual provided with Mobile Console details.
Weight (packed state)
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2007 Rights Reserved.
E3X-DA-N
Digital Fiber Amplifiers with Differential Outputs (E3X-DA11D/E3X-DA6D)
Characteristics Applicable Fiber Units Through-beam Fiber Units
Sensing distance (mm) (The figures parentheses apply when using 39-F1 Lens Unit.) Sensitivity selection 11-level setting Response time (1680) HIGH (1960) (2590) (980) (1260) (1680) (0.3 dia.) (0.2 dia.) Standard object (mm) (min. sensing object opaque)
Fiber Unit E32-T11R E32-T21R E32-T16WR E32-T16PR
dia. (0.01 dia.)
These values sensing objects that moving. This value applies when response time object this value detectable temperature changes within range ambient operating temperature. (The value sensing objects that moving.) values given above table those that detected digital value 1,000 each sensing area.
Reflective Fiber Units
Sensing distance (mm) Sensitivity selection 11-level setting Response time HIGH 3-11 3-11 Standard object (mm) (min. sensing object opaque) (0.01 dia.) (0.01 dia.)
Fiber Unit E32-D11R E32-D21R
Sensing distances given white paper. These values sensing objects that moving. This value applies when response time object this value detectable temperature changes within range ambient operating temperature. (The value sensing objects that moving.)
Differences Compared with E3X-DA-N Amplifier
Differential-output Models (Edge-detection Models) Type Item Control output output Current consumption ON/OFF output Pre-wired E3X-DA11D Wire-saving connector E3X-DA6D
max. (current consumption: max. power supply voltage VDC) Load current: max., (Residual voltage: max. NPN/PNP output) Open collector Switchable between Light edge detection) Dark (OFF edge detection) Switchable between single edge double edge detection mode Single edge: Double edge: Light OFF-delay timer, Dark ON-delay timer 1-ms units, 5-ms units, units) (Negative values displayed.) (Settings returned defaults.) (HIGH/LOW) One-point teaching level varied from increments Operation indicator (orange), 7-segment digital incident level display (red), 7-segment digital detection level display (red)
Detection mode Response time Timer functions Functions Zero-reset Initial reset Sensitivity selection Teaching level Indicators
other information, refer instruction manual supplied with product.
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2007 Rights Reserved.
E3X-DA-N
Engineering Data (Typical)
E3X-DA-N/E3X-DA@V/E3X-DA@TW
Parallel Operating Range maximum sensitivity. (Use optical axis adjustment installation.) Through-beam Through-beam Through-beam E32-T11L E32-T11L E39-F1 (separately sold E32-T12L Long-distance Lens Unit)
Distance (mm)
Distance (mm)
Distance (mm)
-200 -400 -600 -800 High speed Standard
Standard
-200 -400 -600 -800 High speed Standard
Distance
-200 -400 -600 -800 Super-long distance
Distance
Super-high speed
Distance
Super-long distance
Super-long distance
Through-beam E32-TC200
Distance (mm)
-200 -400 Super-long distance -600
Through-beam E32-TC200 E39-F1 (separately sold Long-distance Lens Unit)
Distance (mm)
Standard -200 -400 -600 High speed Super-long distance
Through-beam E32-T11R
Distance (mm)
-100 -200 -300 -400
Standard
Super-high speed
Distance
Distance
Super-high speed
Standard
Distance
Super-long distance
Through-beam E32-T12R
Distance (mm)
-100 -200 -300 -400 Super-high speed Super-long distance
Through-beam E32-T21R
Distance (mm)
High speed Super-long distance Standard
Through-beam E32-T22R
Distance (mm)
Standard Super-long distance Super-high speed
Distance
Standard
Distance (mm)
Distance (mm)
Through-beam E32-T11
Distance (mm)
Standard -200 -400 -600 -800 Super-high speed
Through-beam E32-T22B
Distance (mm)
-100 -150 -200 High speed Super-long distance Standard
Through-beam E32-T14LR
Distance (mm)
-100 Super-long distance -150 Super-high speed
Super-long distance
Distance (mm)
Distance
Standard
Distance (mm)
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2007 Rights Reserved.
E3X-DA-N
Through-beam E32-T24R
Distance (mm)
Super-high speed Super-long distance Standard
Through-beam E32-T81R
Distance (mm)
Through-beam E32-T51
Distance (mm)
-200 -400 Super-long distance -600 -800 High speed Super-long Standard distance
Distance (mm)
-100 -200 -300
High speed Standard
Distance (mm)
Distance
Through-beam E32-T61
Distance (mm)
-100 -200 -300 -400 -500 High speed
Through-beam E32-T61 E39-F1 (separately sold Long-distance Lens Unit)
Distance (mm)
-200 -400 -600
Through-beam E32-T22S
Distance (mm)
Standard -100 High speed Super-long distance
Standard High speed Super-long distance
Distance
Super-long distance Standard
Distance
Distance
-150 -200
Through-beam E32-T24S
Distance (mm)
Through-beam E32-T16W
Distance (mm)
Super-long distance -120 Standard
Through-beam E32-T16WR
Distance (mm)
-100 -150 Super-long distance Standard Super-high speed
Standard High speed
High speed Super-long distance
Distance
Distance
Distance
Through-beam E32-T16J
Distance (mm)
-100 -150 -200 Super-long distance High speed Standard
Through-beam E32-T16J
Distance (mm)
-100 -150 -200 High speed
Through-beam E32-T16JR
Distance (mm)
Super-high speed
Distance
Distance
Standard Super-long distance
Standard -100 -150
Distance
Super-long distance
Through-beam E32-T16P
Distance (mm)
-100 -150 Standard Super-long distance
Through-beam E32-T16PR
Distance (mm)
-100 -150 -200 Standard Super-high speed
High speed
Distance
Distance
Super-long distance
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2007 Rights Reserved.
E3X-DA-N
Operating Range With standard sensing object maximum sensitivity. (Use positioning object Sensor.) Reflective Reflective Reflective E32-D21L E32-DC200 E32-D11R
Distance (mm)
Distance (mm)
Standard High speed -150
Distance (mm)
Standard
Super-long distance Super-high speed
Standard
Distance (mm)
Super-long distance
-100
Distance (mm)
High speed
Distance (mm)
Super-long distance
Reflective E32-D12R
Distance (mm)
-100 Super-high speed Standard Super-long distance
Reflective E32-D21R
Distance (mm)
High speed Super-long distance Standard
Reflective E32-D22R
Distance (mm)
Super-long Super-high speed Standard distance
Distance (mm)
Distance (mm)
Distance (mm)
Reflective E32-D33
Distance (mm)
Super-long distance Super-high speed Standard
Reflective E32-D331
Distance (mm)
-0.2 -0.4 -0.6 Standard Super-long distance High speed
Reflective E32-D21B
Distance (mm)
High speed Super-long distance Standard
Distance (mm)
Distance (mm)
Distance (mm)
Reflective E32-D22B
Distance (mm)
High speed Super-long distance Standard
Reflective E32-C31
Distance (mm)
Standard Super-long distance High speed
Reflective E32-C41
Distance (mm)
Standard
High speed
Distance (mm)
Distance (mm)
Distance (mm)
Super-long distance
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2007 Rights Reserved.
E3X-DA-N
Reflective E32-C42
Distance (mm)
Standard High speed
Reflective E32-D32
Distance (mm)
Super-long distance High speed Standard
Reflective E32-D14LR
Distance (mm)
Super-high speed
Distance (mm)
Super-long distance
Distance (mm)
Distance (mm)
Standard Super-long distance
Reflective E32-D24
Distance (mm)
High speed Super-long distance Standard
Reflective E32-D24R
Distance (mm)
Super-high speed Standard Super-long distance
Reflective E32-D61
Distance (mm)
-120 High speed Super-long distance Standard
Distance (mm)
Distance (mm)
Distance (mm)
Reflective E32-D36P1
Distance (mm)
Reflective E32-D36P1
Distance (mm)
Standard High speed -120 Super-long distance
Reflective E32-L56E@
Distance (mm)
-0.5 -1.0 -1.5 -2.0
Distance (mm)
High speed Standard Super-long distance
-100 -150 -200
Distance (mm)
Distance (mm)
Limited Reflective E32-L25L
Distance (mm)
Distance (mm)
-0.5
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2007 Rights Reserved.
E3X-DA-N
Excess Gain Ratio Distance With standard sensing object maximum sensitivity. Through-beam Reflective Reflective E32-TC200 E32-DC200 E32-D21L
Excess gain ratio (times) Excess gain ratio (times) Excess gain ratio (times)
1,000 Standard 1,000 1,000
Super-long distance
Super-long distance
Super-long distance
Oper- ating level
Super-high speed
Oper1 ating level
Super-high speed
Standard
Oper1 ating level
Super-high speed
Standard
Distance
Distance (mm)
Distance (mm)
Operating Range Reflective E32-DC200
Distance (mm)
Hysteresis Sensing Distance Reflective E32-D11L
Hysteresis (mm)
Super-high speed Sensing object: White paper
Distance Hysteresis
Repeat Accuracy Sensing Distance Reflective E32-DC200
Repeat accuracy (mm)
Sensing object: White paper
0.02-mm -dia. copper wire
0.1-mm -dia. copper wire
Super-high speed
Standard
Standard
Distance (mm)
0.4-mm-dia. copper wire
Super-long distance
Super-long distance
Distance (mm)
Distance (mm)
E3X-DA-N
Monitor Output Distance (Standard Mode) Through-beam Reflective E32-TC200 E32-DC200
Monitor output
Monitor output
Distance (mm)
Distance (mm)
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2007 Rights Reserved.
E3X-DA-N
E3X-DAB-N/E3X-DAG-N
Parallel Operating Range maximum sensitivity. (Use optical axis adjustment installation.) Through-beam Through-beam E32-TC200 E32-TC200 E39-F1(separately sold Long-distance Lens Unit)
Distance (mm) Distance (mm)
Standard Super-high speed Superlong distance
Distance (mm)
Distance
Super-high speed Standard Super-long distance
-100 -150 -200
Operating Range With standard sensing object maximum sensitivity. (Use positioning object Sensor.) Reflective Reflective Limited Reflective E32-DC200 E32-CC200 E32-D11L
Distance (mm) Distance (mm)
Super-high speed Standard Super-long distance
Distance (mm)
Super-long distance Super-high speed Standard
Distance (mm)
Distance (mm)
Distance (mm)
Super-high speed Standard Super-long distance
E3X-DAH-N
Parallel Operating Range maximum sensitivity. (Use optical axis adjustment installation.) Through-beam Through-beam Through-beam E32-TC200 E32-T11L E32-T14
Distance (mm)
Distance (mm)
Super-high speed
Distance (mm)
Super-high speed Standard Super-long distance
Super-long distance Super-high speed Standard
Standard Super-long distance
Distance
-100 -200 -300 -400
Distance
Distance
-100 -150 -200
-100 -150 -200
Operating Range With standard sensing object maximum sensitivity. (Use positioning object Sensor.) Reflective Reflective Limited Reflective E32-DC200 E32-D11L E32-CC200
Distance (mm) Distance (mm)
Super-long distance Standard Super-high speed
Distance (mm)
Distance (mm)
Super-high speed Standard Super-long distance
Distance (mm)
Super-high speed
Standard
Super-long distance
Distance (mm)
other information Fiber Units, refer Fiber Sensors Best Selection Catalog (Cat. E353).
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2007 Rights Reserved.
E3X-DA-N
Technical Reference (for E3X-DA-TW Twin-output Models)
Output Patterns Normal Operation Outputs operate independently either Light mode Dark mode selected (independently) channels 1and making total possible output patterns.
Threshold Light Threshold Light
4000 3000 Threshold
following examples, threshold 3,000, threshold 1,000.)
Threshold Dark Threshold Light
4000 3000 Threshold
Incident level
Incident level
Output Patterns Area Sensing This series includes models equipped with area sensing functionality, first Digital Fiber Amplifiers. This functionality used monitor whether incident level inside outside threshold area. output patterns below possible this kind operation.
inside threshold area
1000
Threshold Time
1000
Threshold
4000
Output Output
Output
Output
Incident level
Time
3000
Threshold
1000
Threshold Time
Threshold Light Threshold Dark
4000 3000
Threshold Dark Threshold Dark
4000 3000 Threshold
Output
Incident level
Incident level
Threshold
Output
outside threshold area
4000 1000 Threshold Time 3000 Threshold
1000
Threshold Time
Output Output
Output Output
Incident level
1000
Threshold Time
Output Output
Note: Output always OFF.
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2007 Rights Reserved.
E3X-DA-N
Circuit Diagrams
Output
Model Operation mode Timing charts
Incident light incident light Operation indicator (orange) Output transistor
Mode selector switch
Output circuit
Operation indicator (orange)
E3X-DA11-N E3X-DAB11-N E3X-DAG11-N E3X-DAH11-N E3X-DA11V E3X-DA6 E3X-DAB6 E3X-DAG6 E3X-DAH6 E3X-DA14V
Light-ON
L-ON (LIGHT
Brown Black Load Control output
Display
Operate Load (e.g., relay) Reset (Between brown black) Incident light incident light Operation indicator (orange) Output transistor
Photoelectric Sensor main circuit
Blue
Dark-ON
D-ON (DARK
Connector Arrangement (M-8 Connector only) Note: used.
Operate Load (e.g., relay) Reset (Between brown black) Incident light incident light Operation indicator (orange) Output transistor
Light-ON
E3X-DA21-N E3X-DA7
Operate Load (e.g., relay) Reset (Between brown black) Incident light incident light Operation indicator (orange) Output transistor Operate Load (e.g., relay) Reset (Between brown black) CH1/ Incident light incident light Operation indicator (orange) Output transistor Operate Load (e.g., relay) Reset (Between brown black) CH1/ Incident light incident light Operation indicator (orange) Output transistor
L-ON (LIGHT
Display
Operation indicator (orange)
Brown Load Black Control output Orange Monitor output Load Blue
Photoelectric Sensor main circuit
Dark-ON
D-ON (DARK
Load resistance: min.
Light-ON
L-ON (LIGHT
Operation indicator (orange) Display
Operation indicator (orange)
Brown Black Load
E3X-DA11TW E3X-DA6TW
Photoelectric Sensor main circuit
Control output Load Orange Control output
Blue
Dark-ON
D-ON (DARK
Operate Load (e.g., relay) Reset (Between brown black)
Note: With E3X-DA@TW models, only channel output when area sensing operation. LIGHT when incident level between thresholds channels DARK when incident level between thresholds channels (Channel always OFF.)
Sensor Connectors Models with Connectors
Classification Wire colors Brown White Blue Black Connection Application Power supply (+V) -Power supply Output
Wire colors Brown White Blue Black
XS3F-M421-402-A XS3F-M421-405-A XS3F-M422-402-A XS3F-M422-405-A
Note: used.
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2007 Rights Reserved.
E3X-DA-N
Output
Model Operation mode Timing charts
Incident light incident light Operation indicator (orange) Output transistor Load (e.g., relay) Operate Reset (Between blue black)
Mode selection switch
Output circuit
Operation indicator (orange)
Brown
E3X-DA41-N E3X-DAB41-N Light-ON E3X-DAG41-N E3X-DAH41-N E3X-DA41V E3X-DA8 E3X-DAB8 E3X-DAG8 E3X-DAH8 Dark-ON E3X-DA44V
L-ON (LIGHT
Display
Photoelectric Sensor main circuit
Control output Black Load
Incident light incident light Operation indicator (orange) Output transistor
Blue
D-ON (DARK
Operate Load (e.g., relay) Reset (Between blue black) Incident light incident light Operation indicator (orange) Output transistor
Connector Arrangement (M-8 Connector only) Note: used.
Light-ON
E3X-DA51-N E3X-DA9
Operate Load (e.g., relay) Reset (Between blue black) Incident light incident light Operation indicator (orange) Output transistor Operate Load (e.g., relay) Reset (Between blue black) CH1/ Incident light incident light Operation indicator (orange) Output transistor Operate Load (e.g., relay) Reset (Between blue black) CH1/ Incident light incident light Operation indicator (orange) Output transistor
L-ON (LIGHT
Display
Operation indicator (orange)
Brown
Photoelectric Sensor main circuit
Control output Black
Monitor output Load
Orange Load
Dark-ON
D-ON (DARK
Blue Load resistance: min.
Light-ON
L-ON (LIGHT
Operation indicator (orange) Display
Operation indicator (orange)
Brown Control output Black Control output Orange Load
E3X-DA41TW E3X-DA8TW
Photoelectric Sensor main circuit
Load
Dark-ON
D-ON (DARK
Blue
Operate Load (e.g., relay) Reset (Between blue black)
Note: With E3X-DA@TW models, only channel output when area sensing operation. LIGHT when incident level between thresholds channels DARK when incident level between thresholds channels (Channel always OFF.)
Sensor Connectors Models with Connectors
Wire colors Brown White Blue Black
Classification
Wire colors Brown White Blue Black
XS3F-M421-402-A XS3F-M421-405-A XS3F-M422-402-A XS3F-M422-405-A
Connection
Application Power supply (+V) -Power supply Output
Note: used.
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2007 Rights Reserved.
E3X-DA-N
Connection
Connection with K3NX-VD2@ Process Meter
K3NX-VD2@
Monitor output Orange Brown Blue E3X-DA-N VDC,
Note Various Units available K3NX. Select appropriate output type depending application. This wiring K3NX with power supply specifications Monitor (Analog) Sensor with power supply specifications. Check respective power supply specifications before wiring. this service power supply Sensor with reference power consumption each Sensor.
Nomenclature
Amplifiers
Standard, Monitor-output, Mark-detecting, Infrared, Water-resistant Models
Setting Buttons TEACH MODE
Lock Button
Level Display
Operation Indicator when output when output OFF.
Operating Mode Selector switch between Light Dark modes. Mode Selector select SET, ADJ, mode.
Twin-output Models
Setting Buttons TEACH MODE
Lock Button
Level Display
Operation Indicator when output
Channel-selection Switch switch between channels Mode Selector select SET, ADJ, mode.
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2007 Rights Reserved.
E3X-DA-N
Amplifier Adjustments
Models
Changing Display (RUN Mode) Zero-reset (RUN Mode)
Digital incident level (4000 max.)
mode selector RUN.
Digital incident level (4000 max.)
mode selector RUN.
(Factory-set RUN)
TEACH MODE
reset zero again:
TEACH
Digital percent
return initial digital incident level:
TEACH MODE
Hold down both
MODE
*There limit number times zero-reset used.
Analog incident level threshold
Initial Reset (SET Mode)
mode selector SET.
MODE
TEACH
MODE
Manual Tuning (Fine Sensitivity Adjustment) Mode Perform fine sensitivity adjustment after teaching manual tuning (without using teaching function) shown below:
Twin-output Models
First, select channel adjusted using channel selection switch.
Hold down both
TEACH
MODE
MODE
Cancel
Execute initial reset
mode selector ADJ.
Fine sensitivity adjustment
TEACH MODE
Sensitivity increment with threshold decrement
Sensitivity decrement with threshold increment
items displayed mode vary with display setting mode.
mode Digital incident level Digital percent Analog value mode Digital threshold Digital percent Analog value
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2007 Rights Reserved.
E3X-DA-N
Setting Functions Mode
mode selector SET.
Teaching
Digital incident level display
Four types sensitivity settings available. Refer page details.
MODE
Sensing function
Displayed "F."
Monitor Focus
Standard (factory-set)
TEACH
Available with: E3X-DA21-N E3X-DA51-N E3X-DA7 E3X-DA9
Super-long distance
TEACH MODE
Super-high speed
TEACH MODE
Setting upper limit Alternates between monitoring "A-UP" setting value.
Alternates
(Factory setting)
Timer function (Factory-set)
Displayed "t."
TEACH
units from 4,000. Alternates
TEACH
Adjustable 1-ms units 5-ms units higher.
TEACH
TEACH
Alternates
MODE
Flashing setting (Factory-set)
Displayed "L."
TEACH
Alternates
TEACH
TEACH
TEACH MODE MODE
Note: possible upper limit that lower than lower limit.
Hold setting (Factory-set)
Displayed "H."
Setting lower limit Alternates between monitoring "A-LO" setting value.
(Factory setting)
TEACH
Alternates
TEACH
Peak
TEACH
units from Alternates
Bottom
TEACH MODE
TEACH
Alternates
Display orientation setting Reversing display
TEACH
Standard (factory-set)
TEACH TEACH
Alternates
Reverse
TEACH
Note: possible lower limit that lower than lower limit.
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2007 Rights Reserved.
E3X-DA-N
Twin-output Models
Setting Functions (SET Mode)
mode selector SET.
Teaching
Digital incident level display
Four types sensitivity settings available. Refer page details.
Setting operating mode Changing operating mode
operating mode channel with channel-selection switch changed.
Changed using channel-selection switch
MODE
Timer function
(Factory setting)
Displayed "t."
Channel
Channel
TEACH
Adjustable 1-ms units 5-ms units higher.
L-ON
(Factory setting)
TEACH
L-ON
(Factory setting)
TEACH MODE
TEACH
Flashing setting (factory-set)
Displayed "L."
D-ON
D-ON
MODE
TEACH
Sensing function
Displayed "F."
TEACH
Standard (factory-set)
TEACH MODE
Hold setting (factory-set)
Displayed "H."
Super-long distance
TEACH TEACH
Super-high speed
TEACH
Peak
TEACH
Area
TEACH
Bottom
TEACH MODE
Area Sensing Area sensing possible using threshold values channels channel L-ON, output turns when incident level between thresholds. channel D-ON, output turns when incident level between thresholds. result output control output (Control output always OFF.)
Display orientation setting Reversing display
Standard (factory-set)
TEACH
Reverse
TEACH
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2007 Rights Reserved.
E3X-DA-N
Models
Teaching (SET Mode)
four types teaching given below available. Once setting made, Amplifier operates according settings. level display will flash teaching error occurs. that case, repeat whole teaching procedure.
With twin-output models, switch channel adjusted using channel-selection switch.
mode selector start teaching.
Maximum Sensitivity Setting
Step Operation mode selector SET. Press TEACH button least seconds. Setting complete when level display changes from green. level display will display digital incident level later. mode.
Two-point With/Without-object Teaching
Step
(Red)
Operation mode selector SET.
TEACH
Press TEACH button approximately second when object sensing position.
Object
TEACH
(Green)
level display lit.
(Red)
One-point Without-object Teaching
Step Operation mode selector SET.
Press TEACH button approximately second with object.
TEACH
Press TEACH button approximately second.
TEACH
Teaching complete when green level display lit.The level display will display digital incident level later.
(Green)
mode.
Teaching complete when level display lit. level display will display digital incident level later. mode.
Note: order "with-object" "without-object" setting steps above reversed.
(Red)
Pin-point Teaching (for Positioning)
Step Operation mode selector SET.
threshold automatically with object.
Object
Press TEACH button approximately second with object.
TEACH
Out-
Note: one-point teaching available because difference level fine, two-point teaching.
level display lit.
(Red)
Operating Mode Selector
Operating mode Light-ON L-ON Dark-ON D-ON Operation
Place object desired position, press TEACH button least seconds.
Object
(Factory-set)
Teaching complete when green level display lit. level display will display digital incident level later. (The level display will flash teaching error occurs.)
TEACH
Note: There operating mode selector twin-output models.
(Green)
mode.
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2007 Rights Reserved.
E3X-DA-N
Safety Precautions
WARNING
This product designed rated ensuring safety persons. such purpose. Fiber Connection Disconnection Amplifier uses one-touch locking mechanism. (Only E3X-NM uses locking button mechanism.) Connect disconnect fibers from Amplifier using following procedures: Connection Open protective cover, insert fibers according fiber insertion marks side Amplifier, lower lock button.
Lock button Insertion position
Precautions Correct
product atmospheres environments that exceed product ratings.
Amplifiers
Designing Operation after Turning Power Sensor ready detect within after power supply turned Sensor load connected separate power supplies, sure turn Sensor first. Mounting Joining Separating Amplifiers Joining Amplifiers Mount Amplifiers time onto track.
Fiber
Fiber insertion mark
10.7
Disconnection Remove protective cover raise lock button pull fiber.
Locked
Protective cover
Unlocked
Slide Amplifiers together, line clips, press Amplifiers together until they click into place.
Note: maintain fiber properties, confirm that lock released before removing fiber. Precautions Fiber Connection/Disconnection sure lock unlock lock button within ambient temperature range between 40°C. Mounting Mobile Console Head Leave least between nearest Amplifier Mobile Console head.
Clip
Click into place
Separating Amplifiers Slide Amplifiers away from each other, remove from track time. attempt remove Amplifiers from track without separating them first.)
Note specifications ambient temperature will vary according number Amplifiers used together. details, refer Ratings Specifications. Always turn power supply before joining separating Amplifiers.
Mounting Mobile Console Head With Twin-output models (E3X-DA@@TW), channels (i.e., eight E3X-DA@@TW Amplifiers) using E3X-MC11 Mobile Console. (Operating modes area detection, however, cannot set.) Adjustment Mutual Interference Protection Function There some instability digital display values light from other sensors. this occurs, decrease sensitivity (i.e., increase threshold) perform stable detection. EEPROM Writing Error data written EEPROM correctly power failure during teaching static-electric noise, repeat whole teaching procedure.
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2007 Rights Reserved.
E3X-DA-N
Optical Communications Several Amplifiers slid together used groups. not, however, slide Amplifiers attempt remove Amplifiers during operation. Hysteresis Adjustment hysteresis setting adjusted using Mobile Console. not, however, hysteresis value lower than factory setting. Using setting less than factory setting result incorrect operation. clip also removed using following mechanism, which incorporated construction section underneath clip. Insert clip removed into slit underneath clip another Amplifier.
Amplifiers with Connectors
Mounting
Mounting Connectors Insert Master Slave Connector into Amplifier until clicks into place.
Remove clip rotating Amplifier.
Rotate
Insert
Join Amplifiers together required after Master Slave Connectors have been inserted. Attach stickers (provided accessories) sides Master Slave Connectors that connected other Connectors.
When using E3X-DA-N with Mobile Console, mount Plate shown below.
Sticker
Sticker
Plate
Note: Attach stickers sides with grooves.
Removing Connectors Slide slave Amplifier(s) which Connector removed away from rest group. After Amplifier(s) been separated, press down lever Connector remove attempt remove Connectors without separating them from other Amplifiers first.)
Press down Lever
Pull Strengths Connectors (Including Cables) E3X-CN11, E3X-CN21, E3X-CN22: max. E3X-CN12: max.
Remove
Mounting Plate (PFP-M) Depending mounted, Amplifier move during operation. this case, Plate. Before mounting Plate, remove clip from master Amplifier using nipper similar tool.
Clip
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2007 Rights Reserved.
E3X-DA-N
Accessories
Operating Instructions Sticker E39-Y1 Attach near Sensor. English Japanese sticker Material: Front side: Paper, Reverse side: Adhesive tape
Japanese Sticker
English Sticker
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2007 Rights Reserved.
E3X-DA-N
Dimensions
Pre-wired Amplifiers E3X-DA11-N E3X-DA21-N E3X-DAB11-N E3X-DA41-N E3X-DA51-N E3X-DA11D
With Mounting Bracket Attached
(Unit:
E3X-DAG11-N E3X-DAH11-N E3X-DAB41-N E3X-DAG41-N E3X-DAH41-N
Two, dia.
17.15 13.05
14.7 Incident level indicator Threshold level indicator
Operation indicator 64.3 38.6
Mounting Holes
31.5 10.7 22.4 Two, 3.2-dia. holes
Hole optical communications
Two,
10.75
34.8 Mounting Bracket (E39-L143) (order separately) SUS304 stainless steel
Mounting Bracket also used side E3X-DA11-N/DA41-N/DAB11-N: 4-dia. vinyl-insulated round cable with conductors (Conductor cross section: mm2; Insulationdiameter: mm). Standard length: E3X-DA21-N/DA51-N: 4-dia. vinyl-insulated round cable with conductors (Conductor cross section: mm2; Insulation diameter:1.1 mm). Standard length:
22.4
Pre-wired Amplifiers, Water-resistant Models E3X-DA11V E3X-DA41V
With Mounting Bracket Attached
30.05 25.95 14.7 Incident level indicator Threshold level indicator
Operation indicator 81.5 Two, dia.
10.7 11.2
11.5
23.9 14.4
67.2
Hole optical communications Mounting Bracket (E39-L148) (order separately) SUS304 stainless steel
Mounting Holes
Two,
23.9
Mounting Bracket also used side 4-dia. vinyl-insulated round cable with conductors (Conductor cross section: mm2; Insulation diameter: mm). Standard length:
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2007 Rights Reserved.
E3X-DA-N
Pre-wired Amplifiers, Twin-output Models E3X-DA11TW E3X-DA41TW
With Mounting Bracket Attached
17.15 13.05 14.7 Incident level indicator Threshold level indicator
Two, dia.
Operation indicator 64.3 38.6
Mounting Holes
31.5 10.7 22.4 Two, 3.2-dia. holes Mounting Bracket also used side 4-dia. vinyl-insulated round cable with conductors (Conductor cross section: mm2; Insulation diameter: mm). Standard length: 34.8
Hole optical communications
Two,
10.75
E39-L143 Mounting Bracket (order separately) SUS304 stainless steel
22.4
Amplifiers with Standard Connectors E3X-DA6 E3X-DAG6 E3X-DA7 E3X-DAH6 E3X-DA8 E3X-DAB8 E3X-DA9 E3X-DAG8 E3X-DAB6 E3X-DAH8 E3X-DA6D E3X-DA6-P
Operation indicator
Incident level indicator Threshold level indicator
13.05 17.15 Two, dia.
14.7 64.3
10.7 38.6 36.7
31.5
Hole optical communications
Dimensions with Master Connector Connected
67.5 64.3
Dimensions with Slave Connector Connected
67.5 64.3
E3X-CN11: dia. E3X-CN21: dia. E3X-CN02: With cable
E3X-CN12: dia. E3X-CN22: dia. E3X-CN02: With cable
31.5
31.5 17.45 11.55
12.95
12.95
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2007 Rights Reserved.
E3X-DA-N
Amplifiers with Connectors, Water-resistant Models E3X-DA14V E3X-DA44V *The Mounting Bracket
also used side
With Mounting Bracket Attached
30.05 25.95 14.7 Incident level indicator Threshold level indicator
Operation indicator 81.5 Two, dia.
10.7 11.2
11.5
23.9 14.4
67.2
Hole optical communications E39-L148 Mounting Bracket (order separately) SUS304 stainless steel
Mounting Holes
Two,
23.9
Incident level indicator Amplifiers with Standard Connectors, Twin-output Models Threshold level indicator E3X-DA6TW Operation indicator E3X-DA8TW
13.05 17.15 Two, dia.
14.7 64.3
10.7 38.6 36.7
31.5
Hole optical communications
Dimensions with Master Connector Connected
67.5 64.3
Dimensions with Slave Connector Connected
67.5 64.3
E3X-CN21: dia. 31.5 31.5
E3X-CN22: dia.
12.95
12.95
17.45 11.55
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2007 Rights Reserved.
E3X-DA-N
Amplifiers with Connectors
Master Connectors E3X-CN11 E3X-CN21
10.7 14.4 dia. 2,000
15.1
30±2
10±2
E3X-CN11: 4-dia. vinyl-insulated round cable with conductors (Conductor cross section: mm2; Insulation diameter: mm). E3X-CN21: 4-dia. vinyl-insulated round cable with conductors (Conductor cross section: mm2; Insulation diameter: mm).
Slave Connectors E3X-CN12 E3X-CN22
10.7
2,000
E3X-CN12: dia. E3X-CN22: dia.
14.4
15.1
30±2
10±2
E3X-CN12: 2.6-dia. vinyl-insulated round cable with conductor (Conductor cross section: mm2; Insulation diameter: mm). E3X-CN22: 4-dia. vinyl-insulated round cable with conductors (Conductor cross section: mm2; Insulation diameter: mm).
Mobile Console
E3X-MC11 Mobile Console
adapter jack Communications jack
Mobile Console Head
Communications jack 13.1 16.3 28.8 12.3 17.3 27.7 31.2 36.7 51.3
Menu indicators 52.8
Connection indicator
(38.2) 31.8 13.2
Channel indicator
24.3 30.3
Output indicator Channel buttons Teaching button Enter button Mode button
Mode display
ball plunger
Optical communications position
Escape button
Power supply button
Function button Battery indicators
Accessories (Order Separately)
Mounting Brackets Plate
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2007 Rights Reserved.
Photoelectric Sensors Technical Guide
General Precautions
precautions individual products, refer Safety Precautions individual product information.
WARNING
These Sensors cannot used safety devices presses other safety devices used protect human life. These Sensors designed applications sensing workpieces workers that affect safety.
Precautions Safe
ensure safety, always observe following precautions.
Wiring
Item Typical examples
Power Supply Voltage
voltage excess operating voltage range. Applying voltage excess operating voltage range, applying power (100 greater) Sensor cause explosion burning.
Three-wire Output Sensors
Load Black Blue
Brown Sensor
Load Short-circuiting
short-circuit load. Doing cause explosion burning.
Three-wire Output Sensor
Two-wire Sensors Example: E3E2
Brown Sensor Blue Load (Load short circuit)
Brown Sensor Blue Black
Load (Load short circuit)
Incorrect Wiring
reverse power supply polarity otherwise wire incorrectly. Doing cause explosion burning.
Three-wire Output Sensors Example: Incorrect Polarity
Brown Sensor Blue Load Black
Three-wire Output Sensors Example: Incorrect Polarity Wiring
Load Brown Sensor Blue Black Sensor Brown Load Blue Black
Connection without load
power supply connected directly without load, internal elements burst burn. sure insert load when connecting power supply.
Three-wire Output Sensors
Brown 24VDC
2-wire Sensors Example: E3E2 etc.
Sensor
Brown Black Sensor Blue Blue
Operating Environment
Sensor environment where there explosive inflammable gases. Sensor environments where cables become immersed other liquids where liquids penetrate Sensor. Doing result damage from burning fire, particularly liquid flammable.
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2007 Rights Reserved.
Photoelectric Sensors Technical Guide
Precautions Correct
Design Power Reset Time
Sensor will ready detect within approximately after power turned Sensor load connected separate power supplies, turn Sensor power before turning load power. exceptions this rule indicated Safety Precautions individual product information.
Turning Power
output pulse generated when power turned OFF. recommended that load load line power turned before Sensor power turned OFF.
Power Supply Types
unsmoothed full-wave half-wave rectifying power supply cannot used.
Mutual Interference
Mutual interference state where output unstable because Sensors affected light from adjacent Sensors. following measures taken avoid mutual interference. Countermeasure Concept Sensor with interference prevention function. Through-beam Sensors Reflective Sensors
Sensors mounted close proximity, Sensors with interference prevention function. fewer Sensors: E3X-DA@-S, E3X-MDA, E3C-LDA Fiber Sensors Performance, however, will depend conditions. Refer pages E3X-DA-S/E3X-MDA E3C-LDA. fewer Sensors: E3X-NA Fiber Sensors fewer Sensors: E3T, E3Z, E3ZM, E3ZM-C, E3S-C, E3G-L1/L3, E3S-C Built-in Amplifier Photoelectric Sensors (except Through-beam Sensors) Photoelectric Sensor with separate amplifier mutual interference prevention polarizing filter installed only E3Z-TA allow close-proximity mounting Sensors. Mutual Interference Prevention Polarizing Filter: E39-E11 Check parallel movement distance range catalog, verify distance between adjacent Sensors, install Sensors accordingly distance least times parallel movement distance range. workpieces move from near, chattering occur vicinity operating point. this type application, separate Sensors least times operating range.
Workpiece Workpiece Sensor
Install inference prevention filter. Separate Sensors distance where interference does occur.
Sensor
Alternate Emitters Receivers.
Close mounting Sensors possible alternating Emitters with Receivers zigzag fashion Sensors). However, workpieces close Photoelectric Sensors, light from adjacent Emitter received cause Sensor change incident light state.
Emitter
Workpiece Receiver Receiver
Emitter
Offset optical axes.
there possibility that light from another Sensor enter Receiver, change position Emitter Receiver, place light barrier between Sensors, take other measures prevent light from entering Receiver. (Light enter even Sensors separated more than sensing distance.)
Sensors mounted opposite each other, slant Sensors shown following diagram. (This because Sensors affect each other cause output chattering even separated more than Sensor sensing distance.)
Sensor Sensor
Adjust sensitivity.
Lowering sensitivity will generally help.
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2007 Rights Reserved.
Photoelectric Sensors Technical Guide
Noise
Countermeasures noise depend path noise entry, frequency components, wave heights. Typical measures given following table. Type noise Noise intrusion path countermeasure Before countermeasure Noise enters from noise source through frame (metal).
Sensor Inverter motor
After countermeasure Ground inverter motor less) Ground noise source power supply (0-V side) through capacitor (film capacitor, 0.22 Insert insulator (plastic, rubber, etc.) between Sensor mounting plate (metal).
Insert insulator. Sensor Mounting block (metal) Inverter motor Noise Noise
Common mode noise (inverter noise)
Common noise applied between mounting board lines, respectively.
Mounting block (metal) Noise
Noise
Noise propagates through from noise source directly enters Sensor. Radiant noise
Ingress high-frequency electromagnetic waves directly into Sensor, from power line, etc.
Insert shield (copper) plate between Sensor noise source e.g., switching power supply). Separate noise source Sensor distance where noise does affect operation.
Shield plate (copper)
Noise source
Sensor
Noise source Sensor
Noise enters from power line. Power line noise
Ingress electromagnetic induction from high-voltage wires switching noise from switching power supply
Noise Sensor Noise
Insert capacitor (e.g., film capacitor), noise filter (e.g., ferrite core insulated transformer), varistor power line.
Insert capacitor, etc. Sensor Noise
Wiring Cable
Unless otherwise indicated, maximum length cable extension using wire that greater. Exceptions indicated Safety Precautions individual product information.
Separation from High Voltage (Wiring Method)
cables Sensor together with high-voltage lines power lines. Placing them same conduit duct cause damage malfunction induction interference. general rule, wire Sensor separate system, independent metal conduit, shielded cable.
Cable Tensile Strength
When wiring cable, subject cable tension greater than that indicated following table. Cable diameter Less than greater Tensile strength max. max.
Power line
Work Required Unconnected Leads
Unused leads self-diagnosis outputs other special functions should wrapped with insulating tape prevent contact with other terminals.
Note: subject shielded cable coaxial cable tension.
Repeated Bending
Normally, Sensor cable should bent repeatedly. (For bending-resistant cable, Attachment Moving Parts page C-4.)
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2007 Rights Reserved.
Photoelectric Sensors Technical Guide
Power Supply
When using commercially available switching regulator, ground (frame ground) (ground) terminals. grounded, switching noise power supply cause malfunction.
Mounting Attachment Moving Parts
mount Photoelectric Sensor moving part, such robot hand, consider using Sensors that uses bending-resistant cable (robot cable). Although bending repetition tolerance standard cable approximately 13,000 times, robot cable excellent bending tolerance approximately 500,000 times.
Example Connection with S3D2 Sensor Controller Three-wire Output Sensors
Reverse operation possible using signal input switch S3D2.
Cable Bending Destruction Test (Tough Wire Breaking Test)
With current flowing, bending repeated check number bends until current stops.
Blue Black Brown
S3D2
Weight
Specimen Test Bending angle Bending repetitions Weight Operation bending Bending radius support points
Standard cable x18/0.12 Left/right each -300g through figure once Approx. 13,000 times
Robot cable: Strong, conductive electrical wire 0.15 mm2, shielded Left/right each bends/minute 200g through figure once Approx. 500,000 times
Result
testing conditions standard cable robot cable different. Refer values above table check bend-resistant performance under actual working conditions.
Description/conditions
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2007 Rights Reserved.
Photoelectric Sensors Technical Guide
Adjustments Optical Axis Adjustment
Move Photoelectric Sensor both vertically horizontally center range which operation indicator lit. E3S-C, optical axis mechanical axis same, optical axis easily adjusted aligning mechanical axis.
Receiver Emitter Lock lever Locked position Protective cover Insertion position
Securing Fibers
Fiber Unit uses one-touch locking mechanism. following methods attach remove Fiber Units.
Attaching Fibers
Open protective cover, insert fiber insertion mark side Fiber Unit, then lower lock lever.
Lock released position
Incident indicator Operation indicator Optimum value Incident indicator Operation indicator
Optical axis:
Fiber insertion mark Fiber
Removing Fibers
Open protective cover, lift lock lever, pull fibers.
axis from center lens center beam Emitter axis from center lens center reception area Receiver. Mechanical axis: axis perpendicular center lens.
Emitter Optical axis Optical axis Receiver
Locked position
Lock released position
Protective cover Emission beam
Mechanical axis Reception area
Note:1.To maintain fiber characteristics, make sure that lock released before removing fibers. Lock unlock fibers ambient temperature 40°C.
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2007 Rights Reserved.
Photoelectric Sensors Technical Guide
Operating Environment Water Resistance
water, rain, outside.
Maintenance Inspection Points Check When Sensor Does Operate
Sensor does operate, check following points. wiring connections correct? mounting screws loose? optical axis sensitivity adjusted correctly? sensing object workpiece speed satisfy ratings specifications? foreign objects, such debris dust, adhering Emitter lens Receiver lens? strong light, such sunlight (e.g., reflected from wall), shining Receiver? attempt disassemble repair Sensor under circumstances. determine that Sensor clearly failure, immediately turn power supply.
Ambient Conditions
this Sensor following locations. Otherwise, malfunction fail. Locations exposed excessive dust dirt Locations exposed direct sunlight Locations with corrosive vapors Locations where organic solvents splash onto Sensor Locations subject vibration shock Locations where there possibility direct contact with water, oil, chemicals Locations with high humidity where condensation result
Environmentally Resistive Sensors
E3HQ used locations above.
Lens Case
lens case Photoelectric Sensor primarily made plastic. Dirt should gently wiped with cloth. thinner other organic solvents. case E3ZM, E3ZM-C E3S-C metal. lens, however, plastic.
Optical Fiber Photoelectric Sensors Explosive Atmospheres
Fiber Unit installed hazardous area, Amplifier Unit installed non-hazardous area.
<Reason>
explosion fire electrical equipment occur, both hazardous atmosphere source ignition must same location. Optical energy does ignition source, thus there danger explosion fire. lens, case, fiber covering made plastic, this setup cannot used there possibility contact with solvents that will corrode degrade (e.g., cloud) plastic.
Accessories Using Reflector (E39-R3/R37/RS1/RS2/RS3) During Application
When using adhesive tape rear face, apply after washing away dust with detergent. Reflector cannot mounted there dirt remaining. press E39-RS1/RS2/RS3 with metal fingernail.This weaken performance. This Sensor cannot used locations where chemicals splash Sensor.
<Ignition Source>
Electrical sparks high-temperature parts that have sufficient energy cause explosion hazardous atmosphere called ignition sources.
Connectors
sure connect disconnect connector after turning Sensor. Hold connector cover connect disconnect connector. Secure connector cover hand. pliers, otherwise connector damaged. connector connected securely, connector disconnected vibration proper degree protection Sensor maintained.
Hazardous area
Non-hazardous area
Fiber Unit Amplifier Unit Sensing object
Others Influence from External Electrical Fields
bring transceiver near Photoelectric Sensor wiring, because this cause incorrect operation.
Values Given Typical Examples
data values given typical examples ratings performance indicate specified performance. They rather values from samples taken from production lots, provided reference guidelines. Typical examples include minimum sensing object, engineering data, step (height) detection data, selection list specifications.
Cleaning
Keep organic solvents away from Sensor. Organic solvents will dissolve surface. soft, cloth clean Sensor.
http://www.ia.omron.com/
(c)Copyright OMRON Corporation 2007 Rights Reserved.
Read Understand This Catalog
Please read understand this catalog before purchasing products. Please consult your OMRON representative have questions comments.
Warranty Limitations Liability
WARRANTY
OMRON's exclusive warranty that products free from defects materials workmanship period year other period specified) from date sale OMRON. OMRON MAKES WARRANTY REPRESENTATION, EXPRESS IMPLIED, REGARDING NON-INFRINGEMENT, MERCHANTABILITY, FITNESS PARTICULAR PURPOSE PRODUCTS. BUYER USER ACKNOWLEDGES THAT BUYER USER ALONE DETERMINED THAT PRODUCTS WILL SUITABLY MEET REQUIREMENTS THEIR INTENDED USE. OMRON DISCLAIMS OTHER WARRANTIES, EXPRESS IMPLIED.
LIMITATIONS LIABILITY
OMRON SHALL RESPONSIBLE SPECIAL, INDIRECT, CONSEQUENTIAL DAMAGES, LOSS PROFITS, COMMERCIAL LOSS CONNECTED WITH PRODUCTS, WHETHER SUCH CLAIM BASED CONTRACT, WARRANTY, NEGLIGENCE, STRICT LIABILITY. event shall responsibility OMRON exceed individual price product which liability asserted. EVENT SHALL OMRON RESPONSIBLE WARRANTY, REPAIR, OTHER CLAIMS REGARDING PRODUCTS UNLESS OMRON'S ANALYSIS CONFIRMS THAT PRODUCTS WERE PROPERLY HANDLED, STORED, INSTALLED, MAINTAINED SUBJECT CONTAMINATION, ABUSE, MISUSE, INAPPROPRIATE MODIFICATION REPAIR.
Application Considerations
SUITABILITY
OMRON shall responsible conformity with standards, codes, regulations that apply combination products customer's application product. customer's request, OMRON will provide applicable third party certification documents identifying ratings limitations that apply products. This information itself sufficient complete determination suitability products combination with product, machine, system, other application use. following some examples applications which particular attention must given. This intended exhaustive list possible uses products, intended imply that uses listed suitable products: Outdoor use, uses involving potential chemical contamination electrical interference, conditions uses described this catalog. Nuclear energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles, safety equipment, installations subject separate industry government regulations. Systems, machines, equipment that could present risk life property. Please know observe prohibitions applicable products. NEVER PRODUCTS APPLICATION INVOLVING SERIOUS RISK LIFE PROPERTY WITHOUT ENSURING THAT SYSTEM WHOLE BEEN DESIGNED ADDRESS RISKS, THAT OMRON PRODUCT PROPERLY RATED INSTALLED INTENDED WITHIN OVERALL EQUIPMENT SYSTEM.
Disclaimers
CHANGE SPECIFICATIONS
Product specifications accessories changed time based improvements other reasons. practice change model numbers when published ratings features changed, when significant construction changes made. However, some specifications product changed without notice. When doubt, special model numbers assigned establish specifications your application your request. Please consult with your OMRON representative time confirm actual specifications purchased product.
DIMENSIONS WEIGHTS
Dimensions weights nominal used manufacturing purposes, even when tolerances shown.
ERRORS OMISSIONS
information this catalog been carefully checked believed accurate; however, responsibility assumed clerical, typographical, proofreading errors, omissions.
PERFORMANCE DATA
Performance data given this catalog provided guide user determining suitability does constitute warranty. represent result OMRON's test conditions, users must correlate actual application requirements. Actual performance subject OMRON Warranty Limitations Liability.
PROGRAMMABLE PRODUCTS
OMRON shall responsible user's programming programmable product, consequence thereof.
COPYRIGHT COPY PERMISSION
This catalog shall copied sales promotions without permission. This catalog protected copyright intended solely conjunction with product. Please notify before copying reproducing this catalog manner, other purpose. copying transmitting this catalog another, please copy transmit entirety.
2007.
OMRON Corporation
Industrial Automation Company
http://www.ia.omron.com/
interest product improvement, specifications subject change without notice.
(c)Copyright OMRON Corporation 2007 Rights Reserved.

E3X-DA-N Ultimate Fiber Amplifier Maximum Ease High Performance

Top Searches for this datasheet

Other recent searches