IPS6021(S)(R)PbF INTELLIGENT POWER HIGH SIDE SWITCH Over tem

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

IPS6021(S)(R)PbF INTELLIGENT POWER HIGH SIDE SWITCH Over tem

Datasheet Thumbnail

Top Searches for this datasheet

Data sheet PD60280
IPS6021(S)(R)PbF
INTELLIGENT POWER HIGH SIDE SWITCH
Over temperature shutdown (with auto-restart) Short circuit protection (current limit) Reverse battery protection (turns MOSFET) Full diagnostic capability (short circuit battery) Active clamp Open load detection state Ground loss protection Logic ground isolated from power ground protection
Product Summary Rds(on) Vclamp Limit Open load Packages max. 1.1A
Description
IPS6021(S)(R)PbF five terminal Intelligent Power Switch (IPS) high side configuration. features short circuit, over-temperature, protection, inductive load capability diagnostic feedback. output current limited Ilim value. current limitation activated until thermal protection acts. overtemperature protection turns device junction temperature exceeds Tshutdown value. will automatically restart after junction cooled below Tshutdown value. reverse battery protection turns MOSFET. diagnostic provides different voltage levels each fault condition. double level shifter circuitry will allow large offsets between logic load ground.
TO-220 IPS6021PbF
D-Pak IPS6021SPbF IPS6021RPbF
Typical Connection
+Bat
Rdgp
Vcc(3) Dg(4)
Control
Rdgs
Pull-up resistors required open load short circuit Vbat detection
In(2)
Diag
Gnd(1)
Out(5)
Input Signal
Load
www.irf.com
IPS6021(S)(R)PbF
Absolute Maximum Ratings
Absolute maximum ratings indicate sustained limits beyond which damage device occur. voltage parameters referenced Ground lead. (Tambient=25°C unless otherwise specified).
Symbol
Vout Voffset max. cont. max. max.
Parameter
Maximum output voltage Maximum logic ground load ground offset Maximum input voltage Maximum voltage Maximum continuous voltage Maximum voltage with short circuit protection Maximum current Maximum diagnostic output current Maximum diagnostic output voltage Maximum power dissipation (internally limited thermal protection) Rth=5°C/W IPS6021 Rth=40°C/W IPS6021S 1"sqrt. footprint Rth=50°C/W IPS6021R 1"sqrt. footprint Electrostatic discharge voltage (Human body) C=100pF, R=1500 Between Other combinations Electrostatic discharge voltage (Machine Model) C=200pF,R=0,L=10µH Between Other combinations Max. storage operating temperature junction temperature Soldering temperature seconds)
Min.
Max.
Units
Vcc-35 Vcc+0.3 Vcc-35 Vcc+0.3 -0.3 -0.3
1500 4000
max. Tsoldering
Thermal Characteristics
Symbol
Rth1 Rth2 Rth1 Rth2 Rth3 Rth1 Rth2 Rth3
Parameter
Thermal resistance junction ambient IPS6021 TO220 free Thermal resistance junction case IPS6021 TO220 Thermal resistance junction ambient IPS6021S std. footprint Thermal resistance junction ambient IPS6021S sqrt. footprint Thermal resistance junction case IPS6021S Thermal resistance junction ambient IPS6021R D-Pak std. footprint Thermal resistance junction ambient IPS6021R D-Pak sqrt. footprint Thermal resistance junction case IPS6021R D-Pak
Typ.
Max.
Units
°C/W
Recommended Operating Conditions
These values given quick design. operation outside these conditions, please consult application notes.
Symbol
Iout
Parameter
High level input voltage level input voltage Continuous drain current, Tambient=85°C, Tj=125°C, Vin=5V Rth=5°C/W IPS6021 Rth=40°C/W IPS6021S sqrt. footprint Rth=50°C/W IPS6021R sqrt. footprint Recommended resistor series with Recommended resistor series with reverse battery protection Recommended pull-up resistor Recommended pull-up resistor open load detection Max. switching frequency
Min.
Max.
Units
Rdgs Rdgp max.
www.irf.com
IPS6021(S)(R)PbF
Static Electrical Characteristics
Tj=25°C, Vcc=14V (unless otherwise specified)
Symbol
Rds(on)
Parameter
state resistance Tj=25°C state resistance Tj=150°C state resistance Tj=25°C, Vcc=6V state resistance during reverse battery Operating voltage range with short circuit protection clamp voltage clamp voltage Supply current when Supply current when Input high threshold voltage Input threshold voltage Input hysteresis Input current when device leakage current level voltage
Min.
Typ.
Max.
Units
Test Conditions
Vin=5V, Iout=10A Vin=5V, Iout=10A Vin=5V, Iout=5A Vcc-Gnd=14V
clamp clamp hyst.
0.25
Iout=40mA Iout=8A (see Fig. Vin=0V, Vout=0V Vin=5V
Vin=5V Vdg=5V Idg=1.6mA
Switching Electrical Characteristics
Vcc=14V, Resistive load=6, Vin=5V, Tj=25°C
Symbol
Tdon dV/dt (On) Tdoff dV/dt (Off) EOff
Parameter
Turn-on delay time Rise time Vout=Vcc-5V Rise time Vout=0.9 Turn dV/dt Turn energy Turn-off delay time Fall time Vout=0.1 Turn dV/dt Turn energy
Min.
Typ.
Max.
Units
V/µs V/µs
Test Conditions
Fig.
www.irf.com
IPS6021(S)(R)PbF
Protection Characteristics
Symbol
Ilim Tsd+ TsdVsc hyst.
Parameter
Internal current limit Over temperature high threshold Over temperature threshold Short-circuit detection voltage(2)
Min.
150(1)
Typ.
Max.
Units
Test Conditions
Vout=0V fig.
Open load detection threshold Open load detection threshold
0.25
Guaranteed design Reference
True Table
Operating Conditions
Normal Normal Open Load Open Load Short circuit Short circuit Short circuit Short circuit Over-temperature Over-temperature With pull-up resistor connected between output Vcc. lower than 10mV. Without pull-up resistor connected between output Vcc.
Lead Assignments
12345
TO220
www.irf.com
IPS6021(S)(R)PbF
Functional Block Diagram
values typical
165°C
158°C Vcc-gnd 2.5V Level Shifter
Charge Pump
Driver
150k
2.0V Over-temp Open load Limit sense
Short circuit
Open load Ground Disconnect
20mV
www.irf.com
IPS6021(S)(R)PbF
clamp
Iout
limiting Ilim Thermal cycling
Tsd+ Tsd-
clamp
Application Notes evaluate power dissipation
Figure Active clamp waveforms
Figure Protection timing diagram
Tr-in
Vclamp
Vcc-5V
Vout
Vout
During active clamp, Vload negative
Iout
Figure Switching times definitions
Figure Active clamp test circuit
www.irf.com
IPS6021(S)(R)PbF
1000
200%
Rds(on), Drain-to-Source Resistance (Normalized)
Eon, Eoff, switching energy (µJ)
150%
100%
Eoff
Iout, Output current Figure Switching energy (µJ) Output current
junction temperature (°C) Figure Normalized Rds(on) (°C)
TO220 5°C/W
D2Pak 40°C/W DPak 50°C/W
Ids, cont. Output current
Iout, Output current
0.001
0.01
Load inductance (mH) Figure Max. Output current Load inductance (mH)
Tamb, Ambient temperature (°C) Figure Max. ouput current Ambient temperature (°C)
www.irf.com
IPS6021(S)(R)PbF
Zth, transient thermal impedance (°C/W)
limit
0.01
Time
Figure Transient thermal impedance (°C/W) time
junction temperature (°C)
Figure limit junction temperature (°C)
1.E+4
1.E+4
off, supply current (µA)
1.E+3
off, supply current (µA)
1.E+3
1.E+2
1.E+2
1.E+1
1.E+1
1.E+0
1.E+0
Vcc, power supply voltage Figure (µA)
junction temperature (°C)
Figure (µA) (°C)
www.irf.com
IPS6021(S)(R)PbF
Case Outline TO220 lead) Automotive Q100 qualified
www.irf.com
IPS6021(S)(R)PbF
Case Outline Lead D2PAK Automotive Q100 MSL1 qualified
www.irf.com
IPS6021(S)(R)PbF
Tape Reel
Lead D2PAK
www.irf.com
IPS6021(S)(R)PbF
Case Outline Lead DPAK Automotive Q100 MSL1 qualified
www.irf.com
IPS6021(S)(R)PbF
Tape Reel
Lead DPAK
WORLD HEADQUARTERS: Kansas St., Segundo, California 90245 Tel: (310) 252-7105 Data specifications subject change without notice. TO220, D2Pak Dpak MSL1 qualified This product been designed qualified Automotive [Q100] market. 11/25/2006
www.irf.com
Note: most current drawings please refer website http://www.irf.com/package/

IPS6021(S)(R)PbF INTELLIGENT POWER HIGH SIDE SWITCH Over tem

Top Searches for this datasheet

Other recent searches