15-V Digital ±7.5-V Peak-to-Peak Switching 125- Typical On-State Resis
|
|
|
Top Searches for this datasheet
CD4066B CMOS QUAD BILATERAL SWITCH
15-V Digital ±7.5-V Peak-to-Peak Switching 125- Typical On-State Resistance 15-V Operation Switch On-State Resistance Matched Within Over 15-V Signal-Input Range On-State Resistance Flat Over Full Peak-to-Peak Signal Range High On/Off Output-Voltage Ratio: Typical kHz, High Degree Linearity: <0.5% Distortion Typical kHz, p-p, Extremely Off-State Switch Leakage, Resulting Very Offset Current High Effective Off-State Resistance: Typical 25°C Extremely High Control Input Impedance (Control Circuit Isolated From Signal Circuit): 1012 Typical Crosstalk Between Switches: Typical MHz,
Matched Control-Input Signal-Output Capacitance: Reduces Output Signal Transients Frequency Response, Switch Typical 100% Tested Quiescent Current 5-V, 10-V, 15-V Parametric Ratings Meets Requirements JEDEC Tentative Standard 13-B, Standard Specifications Description Series CMOS Devices Applications: Analog Signal Switching/Multiplexing: Signal Gating, Modulator, Squelch Control, Demodulator, Chopper, Commutating Switch Digital Signal Switching/Multiplexing Transmission-Gate Logic Implementation Analog-to-Digital Digital-to-Analog Conversion Digital Control Frequency, Impedance, Phase, Analog-Signal Gain
PACKAGE (TOP VIEW)
IN/OUT OUT/IN OUT/IN IN/OUT CONTROL CONTROL
CONTROL CONTROL IN/OUT OUT/IN OUT/IN IN/OUT
description/ordering information
CD4066B quad bilateral switch intended transmission multiplexing analog digital signals. pin-for-pin compatible with CD4016B, exhibits much lower on-state resistance. addition, on-state resistance relatively constant over full signal-input range. CD4066B consists four bilateral switches, each with independent controls. Both devices given switch biased simultaneously control signal. shown Figure well n-channel device each switch tied either input (when switch (when switch off). This configuration eliminates variation switch-transistor threshold voltage with input signal and, thus, keeps on-state resistance over full operating-signal range. advantages over single-channel switches include peak input-signal voltage swings equal full supply voltage more constant on-state impedance over input-signal range. However, sample-and-hold applications, CD4016B recommended.
Please aware that important notice concerning availability, standard warranty, critical applications Texas Instruments semiconductor products disclaimers thereto appears this data sheet.
Copyright 2003, Texas Instruments Incorporated
PRODUCTION DATA information current publication date. Products conform specifications terms Texas Instruments standard warranty. Production processing does necessarily include testing parameters.
POST OFFICE 655303
DALLAS, TEXAS 75265
CD4066B CMOS QUAD BILATERAL SWITCH
description/ordering information (continued)
ORDERING INFORMATION
CDIP PDIP SOIC TSSOP PACKAGE Tube Tube Tube -55°C 125°C Reel 2500 Reel Reel 2000 Tube Reel 2000 ORDERABLE PART NUMBER CD4066BF3A CD4066BE CD4066BM CD4066BM96 CD4066BMT CD4066BNSR CD4066BPW CD4066BPWR CD4066B CM066B CD4066BM TOP-SIDE MARKING CD4066BF3A CD4066BE
Package drawings, standard packing quantities, thermal data, symbolization, design guidelines available www.ti.com/sc/package. Switch Control
Control
control inputs protected CMOS protection network. NOTES: substrates connected VDD. Normal operation control-line biasing: switch (logic VDD; switch (logic Signal-level range:
92CS-29113
Figure Schematic Diagram One-of-Four Identical Switches Associated Control Circuitry
POST OFFICE 655303
DALLAS, TEXAS 75265
CD4066B CMOS QUAD BILATERAL SWITCH
absolute maximum ratings over operating free-air temperature (unless otherwise noted)
supply-voltage range, (voltages referenced terminal) -0.5 Input voltage range, (all inputs) -0.5 input current, (any input) Package thermal impedance, (see Note package 80°C/W package 86°C/W package 76°C/W package 113°C/W Lead temperature (during soldering): distance 1/16 1/32 inch (1,59 0,79 from case 265°C Storage temperature range, Tstg -65°C 150°C
Stresses beyond those listed under "absolute maximum ratings" cause permanent damage device. These stress ratings only, functional operation device these other conditions beyond those indicated under "recommended operating conditions" implied. Exposure absolute-maximum-rated conditions extended periods affect device reliability. NOTE package thermal impedance calculated accordance with JESD 51-7.
recommended operating conditions
Supply voltage Operating free-air temperature UNIT
POST OFFICE 655303
DALLAS, TEXAS 75265
CD4066B CMOS QUAD BILATERAL SWITCH
electrical characteristics
LIMITS INDICATED TEMPERATURES PARAMETER TEST CONDITIONS Quiescent device current Signal Inputs (Vis) Outputs (Vos) VDD, returned On-state resistance difference between switches Total harmonic distortion -3-dB cutoff frequency (switch -50-dB feedthrough frequency (switch off) Input/output leakage current (switch off) (max) -50-dB crosstalk frequency Vis(p-p) (sine wave centered 1-kHz sine wave Vis(p-p) (sine wave centered Vis(p-p) (sine wave centered VC(A) VC(B) Vis(A) Vp-p, source, VDD, GND, (square wave centered ±0.1 ±0.1 1200 1300 1050 -55°C 0.25 -40°C 0.25 85°C 125°C 25°C 0.01 0.01 0.01 0.02 0.25 UNIT
On-state resistance (max)
±10-5 ±0.1
Propagation delay (signal input signal output) Input capacitance Output capacitance Feedthrough
Cios
POST OFFICE 655303
DALLAS, TEXAS 75265
CD4066B CMOS QUAD BILATERAL SWITCH
electrical characteristics (continued)
LIMITS INDICATED TEMPERATURES CHARACTERISTIC Control (VC) VILC Control input, voltage (max) |Iis| VSS, VDD, VDD, VIHC Control input, high voltage Input current (max) Crosstalk (control input signal output) Turn-on turn-off propagation delay Figure VDD, (square wave), VDD, VDD, GND, GND, (square wave centered ±0.1 ±0.1 (MIN) (MIN) (MIN) ±10-5 ±0.1 TEST CONDITIONS -55°C -40°C 85°C 125°C 25°C UNIT
Maximum control input repetition rate
Input capacitance
switching characteristics
SWITCH INPUT (mA) -55°C 0.64 -0.64 -1.6 -4.2 -40°C 0.61 -0.61 -1.5 25°C 0.51 -0.51 -1.3 -3.4 85°C 0.42 -0.42 -1.1 -2.8 125°C 0.36 -0.36 -0.9 -2.4 13.5 SWITCH OUTPUT,
POST OFFICE 655303
DALLAS, TEXAS 75265
CD4066B CMOS QUAD BILATERAL SWITCH
TYPICAL CHARACTERISTICS
TYPICAL ON-STATE RESISTANCE INPUT SIGNAL VOLTAGE (ALL TYPES)
Channel On-State Resistance +25°C -55°C Supply Voltage (VDD VSS) 125°C Channel On-State Resistance +25°C -55°C -7.5 -2.5
TYPICAL ON-STATE RESISTANCE INPUT SIGNAL VOLTAGE (ALL TYPES)
Supply Voltage (VDD VSS) 125°C
Input Signal Voltage
92CS-27326RI
Input Signal Voltage
92CS-27327RI
Figure
TYPICAL ON-STATE RESISTANCE INPUT SIGNAL VOLTAGE (ALL TYPES)
Channel On-State Resistance Channel On-State Resistance Supply Voltage (VDD VSS) 125°C -7.5 -2.5 Input Signal Voltage
92CS-27329RI
Figure
TYPICAL ON-STATE RESISTANCE INPUT SIGNAL VOLTAGE (ALL TYPES)
125°C -7.5 -2.5 Supply Voltage (VDD VSS)
+25°C -55°C
Input Signal Voltage
92CS-27330RI
Figure
Figure
POST OFFICE 655303
DALLAS, TEXAS 75265
CD4066B CMOS QUAD BILATERAL SWITCH
TYPICAL CHARACTERISTICS
CD4066B Switches |Vis Vos| |Iis|
92CS-30966
Figure Determination Test Condition Control-Input High-Voltage (VIHC) Specification
Keithley Digital Multimeter Range
Plotter Moseley 7030A
92CS-22716
Figure Channel On-State Resistance Measurement Circuit
POWER DISSIPATION PACKAGE SWITCHING FREQUENCY
Power Dissipation Package
TYPICAL CHARACTERISTICS CHANNELS
25°C
Output Voltage
Supply Voltage (VDD)
CD4066B
CD4066B Switches
unused terminals connected
Input Voltage
92CS-30919
Switching Frequency
Figure
Figure
92C-30920
POST OFFICE 655303
DALLAS, TEXAS 75265
CD4066B CMOS QUAD BILATERAL SWITCH
TYPICAL CHARACTERISTICS
Cios
CD4066B Switches
92CS-30922
CD4066B Switches
92CS-30921
Measured Boonton capacitance bridge, model MHz); test-fixture capacitance nulled out.
unused terminals connected VSS.
Figure Typical Characteristics Four Channels
CD4066B Switches
92CS-30923
Figure Off-Switch Input Output Leakage
CD4066B Switches
92CS-30924
unused terminals connected VSS.
unused terminals connected VSS.
Figure Propagation Delay Time Signal Input (Vis) Signal Output (Vos)
Figure Crosstalk-Control Input Signal Output
POST OFFICE 655303
DALLAS, TEXAS 75265
CD4066B CMOS QUAD BILATERAL SWITCH
TYPICAL CHARACTERISTICS
CD4066B Switches
NOTES: unused terminals connected VSS. Delay measured level +10% from ground (turn-on) on-state output level (turn-off).
92CS-30925
Figure Propagation Delay, tPLH, tPHL Control-Signal Output
Repetition Rate
CD4066B Switches
unused terminals connected VSS.
92CS-30925
Figure Maximum Allowable Control-Input Repetition Rate
POST OFFICE 655303
DALLAS, TEXAS 75265
CD4066B CMOS QUAD BILATERAL SWITCH
TYPICAL CHARACTERISTICS
Inputs
92CS-27555
Measure inputs sequentially both VSS. Connect unused inputs either VSS. Measure control inputs only.
Figure Input Leakage-Current Test Circuit
Clock Reset External Reset Clock
CD4018B
CD4018B
CD4066B
CD4049B Signal Inputs CD4049B CD4001B CD4049B
CD4001B
Signal Outputs
Channel
Channel Channel Channel Channel
CD4066B
Channel
CD4066B
CD4066B
Package Count CD4001B CD4049B CD4066B CD4018B
Channel
Maximum Allowable Signal Level
Clock
(VDD VSS) Chan Chan Chan Chan
Channel
92CM-30928
Figure Four-Channel Multiplex System Diagram
POST OFFICE 655303
DALLAS, TEXAS 75265
CD4066B CMOS QUAD BILATERAL SWITCH
TYPICAL CHARACTERISTICS
CD4054B CD4066B Digital Control Inputs
92CS-30927
Analog Inputs
Analog Outputs
Figure Bidirectional Signal Transmission Digital Control Logic
POST OFFICE 655303
DALLAS, TEXAS 75265
CD4066B CMOS QUAD BILATERAL SWITCH
APPLICATION INFORMATION
applications that employ separate power sources drive signal inputs, current capability should exceed VDD/RL effective external load four CD4066B bilateral switches). This provision avoids permanent current flow clamp action supply when power applied removed from CD4066B. certain applications, external load-resistor current include both signal-line components. avoid drawing current when switch current flows into terminals voltage drop across bidirectional switch must exceed (calculated from values shown). current will flow through switch current flows into terminals
POST OFFICE 655303
DALLAS, TEXAS 75265
PACKAGE OPTION ADDENDUM
www.ti.com
28-Feb-2005
PACKAGING INFORMATION
Orderable Device CD4066BE CD4066BF CD4066BF3A CD4066BM CD4066BM96 CD4066BMT CD4066BNSR CD4066BPW CD4066BPWR JM38510/05852BCA
Status ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE ACTIVE
Package Type PDIP CDIP CDIP SOIC SOIC SOIC TSSOP TSSOP CDIP
Package Drawing
Pins Package Plan 2500 2000 2000 Pb-Free (RoHS) None None Pb-Free (RoHS) Pb-Free (RoHS) Pb-Free (RoHS) Pb-Free (RoHS) Pb-Free (RoHS) Pb-Free (RoHS) None
Lead/Ball Finish NIPDAU Call Call NIPDAU NIPDAU NIPDAU NIPDAU NIPDAU NIPDAU Call
Peak Temp Level-NC-NC-NC Level-NC-NC-NC Level-NC-NC-NC Level-2-260C-1 YEAR/ Level-1-235C-UNLIM Level-2-260C-1 YEAR/ Level-1-235C-UNLIM Level-2-260C-1 YEAR/ Level-1-235C-UNLIM Level-2-260C-1 YEAR/ Level-1-235C-UNLIM Level-1-250C-UNLIM Level-1-250C-UNLIM Level-NC-NC-NC
marketing status values defined follows: ACTIVE: Product device recommended designs. LIFEBUY: announced that device will discontinued, lifetime-buy period effect. NRND: recommended designs. Device production support existing customers, does recommend using this part design. PREVIEW: Device been announced production. Samples available. OBSOLETE: discontinued production device.
Plan currently available please check latest availability information additional product content details. None: available Lead (Pb-Free). Pb-Free (RoHS): TI's terms "Lead-Free" "Pb-Free" mean semiconductor products that compatible with current RoHS requirements substances, including requirement that lead exceed 0.1% weight homogeneous materials. Where designed soldered high temperatures, Pb-Free products suitable specified lead-free processes. Green (RoHS Sb/Br): defines "Green" mean "Pb-Free" addition, uses package materials that contain halogens, including bromine (Br) antimony (Sb) above 0.1% total product weight.
MSL, Peak Temp. Moisture Sensitivity Level rating according JEDECindustry standard classifications, peak solder temperature. Important Information Disclaimer:The information provided this page represents TI's knowledge belief date that provided. bases knowledge belief information provided third parties, makes representation warranty accuracy such information. Efforts underway better integrate information from third parties. taken continues take reasonable steps provide representative accurate information have conducted destructive testing chemical analysis incoming materials chemicals. suppliers consider certain information proprietary, thus numbers other limited information available release. event shall TI's liability arising such information exceed total purchase price part(s) issue this document sold Customer annual basis.
Addendum-Page
MECHANICAL DATA
MTSS001C JANUARY 1995 REVISED FEBRUARY 1999
(R-PDSO-G**)
PINS SHOWN
PLASTIC SMALL-OUTLINE PACKAGE
0,65
0,30 0,19
0,10
0,15 4,50 4,30 6,60 6,20 Gage Plane 0,25 0,75 0,50
Seating Plane 1,20 0,15 0,05 0,10
PINS
3,10
5,10
5,10
6,60
7,90
9,80
2,90
4,90
4,90
6,40
7,70
9,60
4040064/F 01/97 NOTES: linear dimensions millimeters. This drawing subject change without notice. Body dimensions include mold flash protrusion exceed 0,15. Falls within JEDEC MO-153
POST OFFICE 655303
DALLAS, TEXAS 75265
IMPORTANT NOTICE Texas Instruments Incorporated subsidiaries (TI) reserve right make corrections, modifications, enhancements, improvements, other changes products services time discontinue product service without notice. Customers should obtain latest relevant information before placing orders should verify that such information current complete. products sold subject TI's terms conditions sale supplied time order acknowledgment. warrants performance hardware products specifications applicable time sale accordance with TI's standard warranty. Testing other quality control techniques used extent deems necessary support this warranty. Except where mandated government requirements, testing parameters each product necessarily performed. assumes liability applications assistance customer product design. Customers responsible their products applications using components. minimize risks associated with customer products applications, customers should provide adequate design operating safeguards. does warrant represent that license, either express implied, granted under patent right, copyright, mask work right, other intellectual property right relating combination, machine, process which products services used. Information published regarding third-party products services does constitute license from such products services warranty endorsement thereof. such information require license from third party under patents other intellectual property third party, license from under patents other intellectual property Reproduction information data books data sheets permissible only reproduction without alteration accompanied associated warranties, conditions, limitations, notices. Reproduction this information with alteration unfair deceptive business practice. responsible liable such altered documentation. Resale products services with statements different from beyond parameters stated that product service voids express implied warranties associated product service unfair deceptive business practice. responsible liable such statements. Following URLs where obtain information other Texas Instruments products application solutions: Products Amplifiers Data Converters Interface Logic Power Mgmt Microcontrollers amplifier.ti.com dataconverter.ti.com dsp.ti.com interface.ti.com logic.ti.com power.ti.com microcontroller.ti.com Applications Audio Automotive Broadband Digital Control Military Optical Networking Security Telephony Video Imaging Wireless Mailing Address: Texas Instruments Post Office 655303 Dallas, Texas 75265 Copyright 2005, Texas Instruments Incorporated www.ti.com/audio www.ti.com/automotive www.ti.com/broadband www.ti.com/digitalcontrol www.ti.com/military www.ti.com/opticalnetwork www.ti.com/security www.ti.com/telephony www.ti.com/video www.ti.com/wireless
Other recent searches
W27C4096 - W27C4096 W27C4096 Datasheet
MX589 - MX589 MX589 Datasheet
MCP6548 - MCP6548 MCP6548 Datasheet
MCP6546 - MCP6546 MCP6546 Datasheet
CP95TEL0900 - CP95TEL0900 CP95TEL0900 Datasheet
AN2619 - AN2619 AN2619 Datasheet
ADC12V170 - ADC12V170 ADC12V170 Datasheet
Privacy Policy | Disclaimer
© 2012 Datasheet Archive
