GP1F361T/GP1F361R Electric optical signal compatible design Three

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

GP1F361T/GP1F361R Electric optical signal compatible design Three

Datasheet Thumbnail

Top Searches for this datasheet

GP1F361T/GP1F361R
GP1F361T/GP1F361R
Electric optical signal compatible design Three kinds terminals integrated into single unit. Compact design with small jack compatible mini-plug OPIC type (Direct interface microcomputer signals) (High fidelity real sound reproduction High speed data transmission Signal transmisson speed: MAX. 8Mbps signal voltage drive 2.7V 3.6V)
Optical Mini-Jack Digital Audio Equipment
Outline Dimensions
2.54 2.54
Unit
18.1
9.65 1.85
11.0
5.05
Applications
Portable
Jack terminal
Device terminal
Jack terminal configuration GP1F361T Drive GP1F361R Vout OPIC light detector
OPIC trademark Sharp stands Optical light detecting element signal processing circuitry integrated single chip.
absence confirmation device specification sheets, SHARP takes responsibility defects that occur equipment using SHARP's devices, shown catalogs, data books, etc. Contact SHARP order obtain latest version device specification sheets before using SHARP's device."
GP1F361T/GP1F361R Absolute Maximum Ratings GP1F361T/GP1F361R Photoelectric conversion element
Parameter Supply voltage Output current (GP1F361R Input voltage GP1F361T Operating temperature Storage temperature Soldering temperature Symbol Topr Tstg Tsol Rating source current sink current Unit
GP1F361T/GP1F361R Jack
Parameter Total power dissipation Isolation voltage Operating temperature Storage temperature Soldering temperature
5s/time times.
Symbol Ptot Viso Topr Tstg Tsol
Rating D.C.12V, A.C. 500V 1min.
Unit
Recommended Operating Conditions GP1F361T
Parameter Supply voltage Operating transfer rate Symbol MIN. TYP. MAX. Unit Mbps
GP1F361R
Parameter Supply voltage Operating transfer rate Receiver input optical power level Symbol MIN. 24.0 TYP. MAX. 14.5 Unit Mbps
Electro-optical Characteristics GP1F361T Photoelectric conversion element
Parameter Peak emission wavelength Optical power output couple with fiber Supply current High level input voltage level input voltage LowHigh delay time HighLow delay time Pulse width distortion Jitter Symbol Conditions Refer Fig. Refer Fig. Refer Fig. Refer Fig. Refer Fig. Refer Fig. Refer Fig. Refer Fig. MIN. TYP.
25°C
MAX. Unit
GP1F361T/GP1F361R GP1F361R Photoelectric conversion element
Parameter Peak sensitivity wavelength Supply current High level output voltage level output voltage Rise time Fall time LowHigh delay time HighLow delay time Pulse width distortion 14.5dBm Jitter 24dBm Symbol Conditions Refer Fig. Refer Fig. Refer Fig. Refer Fig. Refer Fig. Refer Fig. Refer Fig. Refer Fig. Refer Fig. MIN. TYP.
25°C
MAX. Unit
Mechanical Electrical Characteristics GP1F361T/GP1F361R Jack
Parameter Insertion force, Withdrawal force Contact resistance Isolation resistance Symbol Rcon RISO Conditions D.C. 500V, 1min. MIN. TYP. MAX. Unit
Note This jack designed appliacable compact single head plug EIAJ RC-6701A) Measuring method insertion force withdrawal force. Insertion withdrawal force shall measured after inserting withdrawing times using EIAJ RC-6701A standard plug test. Measuring method contact resistance. About movable contact terminal make contacts, measures 100mA less 1000H condition inserting EIAJ 6701A standard plug test.
Fig. Measuring Method Optical Output Coupling Fiber
Standard optical fiber cable GP1F361T Unit measured optical power meter must calibrated have wavelength sensitivity 660nm. (0dB Optical power meter (Anritsu ML93B
Note 3.0V 0.05V (State operating) bundle standard fiber optic cable, make into loop with diameter 10cm more. standard fiber optic cable will specified elsewhere.
GP1F361T/GP1F361R
Fig. Measuring Method Input Voltage Supply Current
Standard fiber optic cable GP1F361T Unit measured optical power meter must calibrated have wavelength sensitivity 660nm. 0dB= Optical power meter (Anritsu ML93B
Input conditions judgement method Conditions 2.1V more 0.8V less
Note ±0.05V (State operating)
Judgement method 21<=PC<= -15dBm, 12mA less PC<= 36dBm, 12mA less
Fig. Measuring Method Pulse Response Jitter
Standard fiber optic cable GP1F361T Unit measured Input Input signal 3Mbps biphase mark PRBS signal Oscilloscope Tektronix 7834 7934 type Trigger Storage mode Standard receiver Output signal
Input signal tPLH tPHL
Standard receiver output
GP1F361T/GP1F361R
Test item
Test item High pulse delay time High pulse delay time Pulse width distortion High Jitter High Jitter Symbol Test condition
tPHL tPLH trigger rise input signal measure jitter rise output trigger fall input signal measure jitter fall output
Notes waveform write time shall seconds. allow waveform distorted increasing brightness much. ±0.05V (State operating) probe oscilloscope must more than less than 10pF.
Fig. Supply Current
Input conditions Supply voltage Optical output coupling fiber Standard transmitter input signal 0.05V 14.5dBm 6Mbps NRZ, Duty50 3Mbps biphase mark PRBS signal
fiber optic cable Standard transmitter Input GP1F361R Unit measured Ammeter Vout
Measuring method
Measured ammeter average amperage)
Fig. Measuring Method Output Voltage Pulse Response
fiber optic cable Standard transmitter Input 6Mbp/s NRZ, duty Tektronix 7834 7934 type Oscilloscope GP1F361R Unit measured Vout
GP1F361R/GP1F361T
Test item
Test item LowHigh pulse delay time HighLow pulse delay time Rise time Fall time Pulse width distortion High level output voltage level output voltage
Notes
Symbol
Standard Transmitter Input signal (CH1 GP1F361R Output signal (CH2
0.05V State operating) fiber coupling light output 14.5dBm/ 24.0dBm. probe oscilloscope must more than less than 10pF. output level) GP1F361R fixed constantly when receivers disturbing light including light, input light) less than 0.1Mbps.
Fig. Measuring Method Jitter
fiber optic cable Standard transmitter Tectronix 7834 7934 type Trigger Storage mode Sweep AUTO/NORM GP1F361R Unit measured Vout
Input
Input signal 3Mbps biphase PRBS signal
Oscilloscope
Input signal
GP1F361R output
GP1F361T/GP1F361R
Test item
Test item High jitter High jitter Symbol
Test condition trigger rise input signal measure jitter rise output trigger fall input signal measure jitter fall output
Notes fiber coupling light output 14.5dBm/ 24.0dBm. waveform write time shall seconds. allow waveform distorted increasing brightness much. 0.05V (State operating) probe oscilloscope must more than less than 10pF.
Optical Mini-Jack Connection Example
Metal part Resin part
Jack side Input output terminal
Plug side Input side LINE Digital input coaxial Optical digital input
Output side LINE HEAD PHONE Digital output coaxial Optical digital output
Compatible with Analog electric signal Digital electric signal Digital optical signal GP1F361R/GP1F361T
Analog electric signal Digital electric signal Digital optical signal
Kinds plug Analog electricity Digital electricity Digital optics plug
Output
Please refer chapter Precautions Use."

GP1F361T/GP1F361R Electric optical signal compatible design Three

Top Searches for this datasheet

Other recent searches