Document Title 128K Banks Synchronous DRAM Revision History 128K

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

Document Title 128K Banks Synchronous DRAM Revision History 128K

Datasheet Thumbnail

Top Searches for this datasheet

A43L8316
Document Title 128K Banks Synchronous DRAM Revision History
128K Banks Synchronous DRAM
History
Initial issue
Issue Date
February 2000
Remark
Preliminary (February, 2000, Version 0.0)
AMIC Technology, Inc.
A43L8316
Features
JEDEC standard 3.3V power supply LVTTL compatible with multiplexed address Dual banks Pulse cycle with address programs Latency (2,3) Burst Length (1,2,4,8 full page) Burst Type (Sequential Interleave) inputs sampled positive going edge system clock Burst Read Single-bit Write operation masking Auto self refresh 16ms refresh period cycle) TSOP (II)
128K Banks Synchronous DRAM
General Description
A43L8316 4,194,304 bits synchronous high data rate Dynamic organized 131,072 words bits, fabricated with AMIC's high performance CMOS technology. Synchronous design allows precise cycle control with system clock. transactions possible every clock cycle. Range operating frequencies, programmable latencies allows same device useful variety high bandwidth, high performance memory system applications.
Configuration
TSOP (II)
NC/RFU
VDDQ
VSSQ
DQ13
DQ12
DQ11
DQ10
UDQM
VDDQ
VSSQ
DQ15
DQ14
A43L8316V
VSSQ
VDDQ
VDDQ LDQM VSSQ
Preliminary (February, 2000, Version 0.0)
AMIC Technology, Inc.
A43L8316
Block Diagram
Control
Data Input Register Bank Select
LDQM
Buffer Refresh Counter
128K
Decoder
Output Buffer
Sense
Address Register
128K
LCBR
LRAS
Column Decoder
Column Buffer
Latency Burst Length
LRAS
LCAS LRAS LCBR
Programming Register LDQM LWCBR
Timing Register
L(U)DQM
Preliminary (February, 2000, Version 0.0)
AMIC Technology, Inc.
A43L8316
Descriptions
Symbol Name System Clock Chip Select Description Active positive going edge sample inputs. Disables Enables device operation masking enabling inputs except CLK, L(U)DQM Masks system clock freeze operation from next clock cycle. Clock Enable should enabled least clock prior command. Disable input buffers power down standby. Column addresses multiplexed same pins. A0~A8/AP Address address RA0~RA8, Column address: CA0~CA7 Selects bank activated during address latch time. Bank Select Address Selects band read/write during column address latch time.
Address Strobe
Latches addresses positive going edge with low. Enables access precharge.
Column Address Strobe Write Enable Data Input/Output Mask Data Input/Output Power Supply/Ground Data Output Power/Ground Connection
Latches column addresses positive going edge with low. Enables column access. Enables write operation precharge. Makes data output Hi-Z, after clock masks output. Blocks data input when L(U)DQM active. Data inputs/outputs multiplexed same pins. Power Supply: +3.3V±0.3V/Ground Provide isolated Power/Ground improved noise immunity.
L(U)DQM DQ0-15 VDD/VSS VDDQ/VSSQ NC/RFU
Preliminary (February, 2000, Version 0.0)
AMIC Technology, Inc.
A43L8316
Absolute Maximum Ratings*
Voltage relative (Vin, Vout -1.0V +4.6V Voltage supply relative (VDD, VDDQ .-1.0V +4.6V Storage Temperature (TSTG) -55°C +150°C Soldering Temperature Time (TSLODER) 260°C 10sec Power Dissipation (PD) Short Circuit Current (Ios) 50mA
*Comments
Permanent device damage occur "Absolute Maximum Ratings" exceeded. Functional operation should restricted recommended operating condition. Exposure higher than recommended voltage extended periods time could affect device reliability.
Electrical Characteristics
Recommend operating conditions (Voltage referenced Parameter Supply Voltage Input High Voltage Input Voltage Output High Voltage Output Voltage Input Leakage Current Output Leakage Current Output Loading Condition Symbol VDD,VDDQ -0.3 Figure VDD+0.3 Unit Note -2mA Note Note Note
Note: (min) -1.5V (pulse width 5ns). input 0.3V, other pins under test Dout disabled, Vout
Decoupling Capacitance Guide Line
Recommended decoupling capacitance added power line board. Parameter Decoupling Capacitance between Decoupling Capacitance between VDDQ VSSQ Symbol CDC1 CDC2 Value 0.01 0.01 Unit
Note: VDDQ pins separated each other. pins connected chip. VDDQ pins connected chip. VSSQ pins separated each other pins connected chip. VSSQ pins connected chip.
Preliminary (February, 2000, Version 0.0)
AMIC Technology, Inc.
A43L8316
Electrical Characteristics
(Recommended operating condition unless otherwise noted, 70°C) Symbol Parameter Operating Current Icc1 Icc2 Icc2 ICC2N (One Bank Active) Precharge Standby Current powerdown mode Test Conditions Burst Length tRC(min), tCC(min), VIL(max), 15ns VIL(max), VIH(min), VIH(min), 15ns Precharge Standby Current power-down mode Input signals changed time during 30ns VIH(min), VIL(max), Input signals stable. ICC3 ICC3 ICC3N Active Standby Current powerdown mode Active Standby current power-down mode (One Bank Active) VIL(max), 15ns VIL(max), VIL(max) VIH(min), VIH(min), 15ns Input signals changed time during 30ns VIH(min), VIL(max), Input signals stable. Operating Current (Burst Mode) 0mA, Page Burst bank Activated, tCCD tCCD (min) ICC5 ICC6 Refresh Current Self Refresh Current (min) 0.2V Latency Speed Unit Notes
ICC2NS
ICC3NS
ICC4
Note: Measured with outputs open. Addresses changed only time during tCC(min). Refresh period 64ms. Addresses changed only time during tCC(min).
Preliminary (February, 2000, Version 0.0)
AMIC Technology, Inc.
A43L8316
Operating Test Conditions
(VDD 3.3V ±0.3V, +70°C) Parameter input levels Input timing measurement reference level Input rise time (See note3) Output timing measurement reference level Output load condition Value VIH/VIL 2.4V/0.4V 1.4V tr/tf 1ns/1ns 1.4V Fig.2
3.3V 1200 Output OUTPUT VOH(DC) 2.4V, -2mA VOL(DC) 0.4V, =1.4V ZO=50 30pF
(Fig. Output Load Circuit
(Fig. Output Load Circuit
Characteristics
operating conditions unless otherwise noted) Symbol Parameter Latency cycle time valid tSAC Output delay Output data hold time high pulse width 1000 Unit Note
Preliminary (February, 2000, Version 0.0)
AMIC Technology, Inc.
A43L8316
Characteristics (continued)
operating conditions unless otherwise noted) Symbol Parameter Latency pulse width Input setup time Input hold time tSLZ output Low-Z output tSHZ Hi-Z Unit Note
*All parameters measured from half half. Note Parameters depend programmed latency. clock rising time longer than 1ns, (tr/2-0.5)ns should added parameter. Assumed input rise fall time 1ns. longer than 1ns, transient time compensation should considered, i.e., [(tr tf)/2-1]ns should added parameter.
Preliminary (February, 2000, Version 0.0)
AMIC Technology, Inc.
A43L8316
Operating Parameter
operating conditions unless otherwise noted) Version Symbol Parameter Latency tRRD(min) active active delay tRCD(min)
delay
Unit
Note
tRP(min)
precharge time
tRAS(min) tRAS(max) active time
tRC(min)
cycle time
tCDL(min)
Last data col. Address delay
tRDL(min)
Last data precharge
tBDL(min)
Last data burst stop
tCCD(min)
Col. Address col. Address delay
Number valid output data
Note: minimum number clock cycles determined dividing minimum time required with clock cycle time then rounding next higher integer. Minimum delay required complete write. parts allow every cycle column address change. case precharge interrupt, auto precharge read burst stop.
Preliminary (February, 2000, Version 0.0)
AMIC Technology, Inc.
A43L8316
Simplified Truth Table
Command Register Refresh CKEn-1 CKEn
A7~A0 Notes
Mode Register Auto Refresh Self Refresh Entry Exit
CODE
Bank Active Addr. Read Auto Precharge Disable Column Addr. Auto Precharge Enable Write Auto Precharge Disable Column Addr. Auto Precharge Enable Burst Stop Precharge Bank Selection Both Banks Clock Suspend Active Power Down Entry Exit Entry Precharge Power Down Mode Exit Operation Command
Addr. Column Addr. Column Addr.
Valid, Don't Care, Logic High, Logic Low) Note Code Operand Code A0~A8/AP,BA Program keys. (@MRS) issued only both banks precharge state. command issued after clock cycle MRS. Auto refresh functions same refresh DRAM. automatical precharge without precharge command meant "Auto". Auto/Self refresh issued only both precharge state. Bank select address. "Low" read, write, active precharge, bank selected. "High" read, write, active precharge, bank selected. A8/AP "High" precharge, ignored both banks selected. During burst read write with auto precharge, read write command cannot issued. Another bank read write command issued every burst length. Burst stop command valid every burst length. sampled positive going edge masks data-in very (Write latency makes data-out Hi-Z state after cycles. (Read latency
Preliminary (February, 2000, Version 0.0)
AMIC Technology, Inc.
A43L8316
Mode Register Filed Table Program Modes
Register Programmed with Address Function
(Note
Latency
Burst Length
(Note
Test Mode Type Mode Register Vendor Only
Latency Latency Reserved Reserved Reserved Reserved Reserved
Burst Type Type Sequential Interleave
Burst Length BT=0 Reserved Reserved Reserved 256(Full) BT=1 Reserved Reserved Reserved Reserved Reserved Reserved (Note
Write Burst Length Length Burst Single
Power Sequence
Apply power start clock, Attempt maintain "H", other pins condition inputs. Maintain stable power, stable clock input condition minimum 200µs. Issue precharge commands banks devices. Issue more auto-refresh commands. Issue mode register command initialize mode register. cf.) Sequence changed. device ready normal operation. Note RFU(Reserved Future Use) should stay during cycle. high during cycle, "Burst Read Single Write" function will enabled. full column burst (256bit) available only Sequential mode burst type.
Preliminary (February, 2000, Version 0.0)
AMIC Technology, Inc.
A43L8316
Burst Sequence (Burst Length Initial address Sequential Interleave
Burst Sequence (Burst Length
Initial address Sequential Interleave
Preliminary (February, 2000, Version 0.0)
AMIC Technology, Inc.
A43L8316
Device Operations
Clock (CLK) clock input used reference SDRAM operations. operations synchronized positive going edge clock. clock transitions must monotonic between VIH. During operation with high inputs assumed valid state (low high) duration hold time around positive edge clock proper functionality specifications. Clock Enable (CLK) clock enable (CKE) gates clock onto SDRAM. goes synchronously with clock (set-up hold time same other inputs), internal clock suspended form next clock cycle state output burst address frozen long remains low. other inputs ignored from next clock cycle after goes low. When both banks idle state goes synchronously with clock, SDRAM enters power down mode form next clock cycle. SDRAM remains power down mode ignoring other inputs long remains low. power down exit synchronous internal clock suspended. When goes high least "tSS CLOCK" before high going edge clock, then SDRAM becomes active from same clock edge accepting input commands. Bank Select (BA) This SDRAM organized independent banks 131,072 words bits memory arrays. inputs latched time assertion select bank used operation. When asserted low, bank selected. When asserted high, bank selected. bank select latched bank activate, read, write mode register precharge operations. Address Input A8/AP) address bits required decode 131,072 word locations multiplexed into address input pins (A0~A8/AP). address latched along with during bank activate command. column address latched along with during read write command. Device Deselect When high, SDRAM performs operation (NOP). does initiate operation, needed complete operations which require more than single clock like bank activate, burst read, auto refresh, etc. device deselect also entered asserting high. high disables command decoder that address inputs ignored. Power-Up following sequence recommended POWER Power must applied either inputs pull them high other pins condition inputs before along with (and VDDQ) supply. clock signal must also asserted same time. After reaches desired voltage, minimum pause microseconds required with inputs condition. Both banks must precharged now. Perform minimum Auto refresh cycles stabilize internal circuitry. Perform MODE REGISTER cycle program latency, burst length burst type default value mode register undefined. clock cycle from mode register cycle, device ready operation. When above sequence used Power-up, out-puts will high impedance state. high impedance outputs guaranteed other power-up sequence. cf.) Sequence charged. Mode Register (MRS) mode register stores data controlling various operation modes SDRAM. programs latency, addressing mode, burst length, test mode various vendor specific options make SDRAM useful variety different applications. default value mode register defined, therefore mode register must written after power operate SDRAM. mode register written asserting
(The SDRAM should active mode with already high prior writing mode register). state address pins A0~A8/AP same cycle going data written mode register. clock cycle required complete write mode register. mode register contents changed using same command clock cycle requirements during operation long both banks idle state. mode register divided into various fields depending functionality. burst length field uses A0~A2, burst type uses addressing mode uses A4~A6, A7~A8/AP used vendor specific options test mode. write burst length programmed using A7~A8/AP must normal SDRAM operation. Refer table specific codes various burst length, addressing modes latencies.
Preliminary (February, 2000, Version 0.0)
AMIC Technology, Inc.
A43L8316
Device Operations (continued)
Bank Activate bank activate command used select random idle bank. asserting Burst Write burst write command similar burst read command, used write data into SDRAM consecutive clock cycles adjacent addresses depending burst length burst sequence. asserting with valid column address, write burst initiated. data inputs provided initial address same clock cycle burst write command. input buffer deselected burst length, even though internal writing have been completed yet. writing complete burst length. burst write terminated issuing burst read blocking data inputs burst write same other active bank. burst stop command valid only full page burst length where writing continues burst burst wrap around. write burst also terminated using blocking data precharging bank "tRDL" after last data input written into active row. OPERATION also. Operation used mask input output operation. works similar during read operation inhibits writing during write operation. read latency cycles from zero cycle write, which means masking occurs cycles later read cycle occurs same cycle during write cycle. operation synchronous with clock, therefore masking occurs complete cycle. signal important during burst interrupts write with read precharge SDRAM. asynchronous nature internal write, operation critical avoid unwanted incomplete writes when complete burst write required. Precharge precharge operation performed active bank asserting A8/AP with valid bank precharged. precharge command asserted anytime after tRAS(min) satisfied from bank activate command desired bank. "tRP" defined minimum time required precharge bank. minimum number clock cycles required complete precharge calculated dividing "tRP" with clock cycle time rounding next higher integer. Care should taken make sure that burst write completed used inhibit writing before precharge command asserted. maximum time bank active specified tRAS(max). Therefore, each bank precharged within tRAS(max) from bank activate command. precharge, bank enters idle state ready activated again. Entry Power Down, Auto refresh, Self refresh Mode register etc, possible only when both banks idle state.
with desired bank addresses, access initiated. read write operation occur after time delay tRCD(min) from time bank activation. tRCD(min) internal timing parameter SDRAM, therefore dependent operating clock frequency. minimum number clock cycles required between bank activate read write command should calculated dividing tRCD(min) with cycle time clock then rounding result next higher integer. SDRAM internal banks same chip shares part internal circuitry reduce chip area, therefore restricts activation both banks immediately. Also noise generated during sensing each bank SDRAM high requiring some time power supplies recover before other bank sensed reliably. tRRD(min) specifies minimum time required between activating different banks. number clock cycles required between different bank activation must calculated similar tRCD specification. minimum time required bank active initiate sensing restoring complete dynamic cells determined tRAS(min) specification before precharge command that active bank asserted. maximum time bank active state determined tRAS(max). number cycles both tRAS(min) tRAS(max) calculated similar tRCD specification.
Burst Read burst read command used access burst data consecutive clock cycles from active active bank. burst read command issued asserting with being high positive edge clock. bank must active least tRCD(min) before burst read command issued. first output appears latency number clock cycles after issue burst read command. burst length, burst sequence latency from burst read command determined mode register which already programmed. burst read initiated column address active row. address wraps around initial address does start from boundary such that number outputs from each equal burst length programmed mode register. output goes into high-impedance burst, unless burst read initiated keep data output gapless. burst read terminated issuing another burst read burst write same bank other active bank precharge command same bank. burst stop command valid every page burst length.
Preliminary (February, 2000, Version 0.0)
AMIC Technology, Inc.
A43L8316
Device Operations (continued)
Auto Precharge precharge operation also performed using auto precharge. SDRAM internally generates timing satisfy tRAS(min) "tRP" programmed burst length latency. auto precharge command issued same time burst read burst write asserting high A8/AP. burst read burst write command issued with A8/AP, bank left active until command asserted. Once auto precharge command given, commands possible that particular bank until bank achieves idle state. Both Banks Precharge Both banks precharged same time using Precharge command. Asserting operation specified "tRC(min)". minimum number clock cycles required calculated driving "tRC" with clock cycle time then rounding next higher integer. auto refresh command must followed NOP's until auto refresh operation completed. Both banks will idle state auto refresh operation. auto refresh preferred refresh mode when SDRAM being used normal data transactions. auto refresh cycle performed once 15.6us burst 1024 auto refresh cycles once 16ms. Self Refresh self refresh another refresh mode available SDRAM. self refresh preferred refresh mode data retention power operation SDRAM. self refresh mode, SDRAM disables internal clock input buffers except CKE. refresh addressing timing internally generated reduce power consumption. self refresh mode entered from banks idle state asserting with high Once self refresh mode entered, only state being matters, other inputs including clock ignored remain self refresh. self refresh exited restarting external clock then asserting high CKE. This must followed NOP's minimum time "tRC" before SDRAM reaches idle state begin normal operation. system uses burst auto refresh during normal operation, recommended used burst 1024 auto refresh cycles immediately after exiting self refresh.
with high A8/AP after both banks have satisfied tRAS(min) requirement, performs precharge both banks. after performing precharge all, both banks idle state.
Auto Refresh storage cells SDRAM need refreshed every 16ms maintain data. auto refresh cycle accomplishes refresh single storage cells. internal counter increments automatically every auto refresh cycle refresh rows. auto refresh command issued asserting with high auto refresh command only asserted with both banks being idle state device power down mode (CKE high previous cycle). time required complete auto refresh
Preliminary (February, 2000, Version 0.0)
AMIC Technology, Inc.
A43L8316
Basic feature Function Descriptions CLOCK Suspend
Click Suspended During Write (BL=4)
Clock Suspended During Read (BL=4)
Masked Internal Masked
DQ(CL2) DQ(CL3)
Written
Suspended Dout
Note: disable/enable=1 clock
Operation
Write Mask (BL=4)
Read Mask (BL=4)
DQ(CL2) DQ(CL3)
Masked Hi-Z Hi-Z
Masked
Data-in Mask 0CLK
Data-out Mask
Read Mask (BL=4)
DQ(CL2) DQ(CL3) Hi-Z Hi-Z Hi-Z Hi-Z Hi-Z Hi-Z
Note makes data Hi-Z after clocks which should masked "L".
masks both data-in data-out.
Preliminary (February, 2000, Version 0.0)
AMIC Technology, Inc.
A43L8316
Interrupt
Read interrupted Read (BL=4) DQ(CL2) DQ(CL3) tCCD
Note2
Note
Write interrupted (Block) Write
Note2
Write interrupted Read
Note2
tCCD
Note4
Note2
tCCD
tCCD
Pixel
Pixel
DQ(CL2) DQ(CL3)
tCDL Note3
tCDL Note3
tCDL Note3
Note "Interrupt", possible stop burst read/write external command before burst. Interrupt", stop burst read/write access; read, write block write. tCCD delay. (=1CLK) tCDL Last data column address delay. 1CLK).
Preliminary (February, 2000, Version 0.0)
AMIC Technology, Inc.
A43L8316
Interrupt (II) Read Interrupted Write
CL=2, BL=4
iii) CL=3, BL=4
Hi-Z
Hi-Z
Hi-Z
Note
iii)
Hi-Z
Hi-Z
Note
Note prevent contention, there should least between data data out. prevent contention, should issued which makes least between data data out.
Preliminary (February, 2000, Version 0.0)
AMIC Technology, Inc.
A43L8316
Write Interrupted Precharge
Masked Note
Note
Note inhibit invalid write, should issued. This precharge command burst write command should same bank, otherwise precharge interrupt only another bank precharge dual banks operation.
Precharge
Normal Write (BL=4) Note Read (BL=4) DQ(CL2) DQ(CL3)
Note
Auto Precharge
Normal Write (BL=4)
Note Auto Precharge Starts
Read (BL=4) DQ(CL2) DQ(CL3)
Note Auto Precharge Starts
Note Number valid output data after Precharge Latency respectively. active command precharge bank issued after from this point. read/write command other active bank issued from this point. burst read/write with auto precharge, interrupt same/another bank illegal.
Preliminary (February, 2000, Version 0.0)
AMIC Technology, Inc.
A43L8316
Burst Stop Precharge Interrupt
Write Interrupted Precharge (BL=4) tRDL
Note
Write Burst Stop (BL=8)
STOP
tBDL (note
Read Interrupted Precharge (BL=4) DQ(CL2) DQ(CL3)
Note
Read Burst Stop (BL=4) DQ(CL2)
STOP
Note
DQ(CL3)
Mode Register
Note
1CLK
Note 1.tRDL 1CLK, Last Data Precharge. tBDL 1CLK, Last Data Burst Stop Delay. Number valid output data after precharge burst stop latency=2,3 respectively. Both banks precharge necessary. issued only bank precharge state.
Preliminary (February, 2000, Version 0.0)
AMIC Technology, Inc.
A43L8316
Clock Suspend Exit Power Down Exit
Clock Suspend (=Active Power Down) Exit Internal
Note
Power Down (=Precharge Power Down) Exit
Internal
Note
Auto Refresh Self Refresh
Note
Auto Refresh
Internal
Note
Note
Note
Self Refresh
Note
Note Active power down more bank active state. Precharge power down both bank precharge state. auto refresh same refresh conventional DRAM. precharge commands required after Auto Refresh command. During from auto refresh command, other command accepted. Before executing auto/self refresh command, both banks must idle state. MRS, Bank Active, Auto/Self Refresh, Power Down Mode Entry. During self refresh mode, refresh interval refresh operation performed internally. After self refresh entry, self refresh mode kept while LOW. During self refresh mode, inputs expect will don't cared, outputs will Hi-Z state. During from self refresh exit command, other command accepted. Before/After self refresh mode, burst auto refresh cycle (1024K cycles recommended.
Preliminary (February, 2000, Version 0.0)
AMIC Technology, Inc.
A43L8316
About Burst Type Control
Basic MODE Sequential counting Interleave counting A3="0". BURST SEQUENCE TABE.(BL=4,8) BL=1,2,4,8 full page wrap around. A3=" BURST SEQUENCE TABE.(BL=4,8) BL=4,8 BL=1,2 Interleave Counting Sequential Counting "1". (See Interleave Counting Mode) Starting Address bits A0-2 should "000" "111".@BL=8. "000" Increment Counting. LSB= "111" Decrement Counting. Example, (Assume Addresses except bits BL=8) write, LSB="000", Accessed Column order 0-1-2-3-4-5-6-7 read, LSB="111", Accessed Column order 7-6-5-4-3-2-1-0 BL=4, same applications possible. above example, Interleave Counting mode, confining starting address some values, PseudoDecrement Counting Mode realized. BURST SEQUENCE TABLE carefully. "0". (See Sequential Counting Mode) A0-2 "111". (See Full Page Mode) Using Full Page Mode Burst Stop Command, Binary Counting Mode realized. Sequential Counting Accessed Column order 3-4-5-6-7-1-2-3 (BL=8) Pseudo-Binary Counting, Accessed Column order 3-4-5-6-7-8-9-10 (Burst Stop command) Note. next column address Every cycle Read/Write Command with random column address realize Random Column Access. That similar Extended Data (EDO) Operation convention DRAM.
PseudoDecrement Sequential Counting
PseudoMODE
Pseudo-Binary Counting
Random MODE
Random column Access tCCD
About Burst Length Control
A2,1,0 "000". auto precharge, tRAS should violated. A2,1,0 "001". auto precharge, tRAS should violated. A2,1,0 "010" A2,1,0 "011". A2,1,0 "111". Full Page Wrap around mode (Infinite burst length) should stopped burst stop, interrupt interrupt. BA="1". BRSW Read burst 1,2,4,8, full page/write Burst auto precharge write, tRAS should violated. tBDL=1, Valid after burst stop CL=2,3 respectively Burst Stop Using burst stop command, possible only full page burst length. Before burst, precharge command same bank Interrupt Stops read/write burst with precharge. (Interrupted Precharge) tRDL=1 with DQM, valid after burst stop CL=2,3 respectively During read/write burst with auto precharge, interrupt cannot issued. Before burst, read/write stops read/write burst starts read/write burst block write. Interrupt During read/write burst with auto precharge, interrupt issued.
Basic MODE
Special MODE Random MODE
Interrupt MODE
Preliminary (February, 2000, Version 0.0)
AMIC Technology, Inc.
A43L8316
Power Sequence Auto Refresh
CLOCK
High level necessary
High level necessary
Precharge (All Banks)
Auto Refresh
Auto Refresh
High-Z
A8/AP
ADDR
Mode Regiser Active (A-Bank) Don't care
Preliminary (February, 2000, Version 0.0)
AMIC Technology, Inc.
A43L8316
Single Read-Write-Read Cycles (Same Page) @CAS Latency=3, Burst Length=1
CLOCK tRAS
*Note
High
tRCD ADDR
*Note *Note
tCCD
*Note *Note *Note *Note
*Note
*Note
*Note
*Note
A8/AP
tRAC tSAC tSLZ tSHZ
Active
Read
Write
Read Precharge
Active
Don't care
Preliminary (February, 2000, Version 0.0)
AMIC Technology, Inc.
A43L8316
Note inputs don't care when high high going edge. Bank active read/write controlled
Active Read/Write Bank Bank
Enable disable auto precharge function controlled A8/AP read/write command. A8/AP Operation Disable auto precharge, leave bank active burst. Disable auto precharge, leave bank active burst. Enable auto precharge, precharge bank burst. Enable auto precharge, precharge bank burst.
A8/AP control bank precharge when precharge command asserted. A8/AP Precharge Bank Bank Both Bank
Preliminary (February, 2000, Version 0.0)
AMIC Technology, Inc.
A43L8316
Read Write Cycle Same Bank @Burst Length=4
CLOCK
tRCD *Note
High
*Note
ADDR
A8/AP
tRAC *Note tSAC tRAC *Note tSAC *Note *Note
tSHZ
tRDL
tSHZ
tRDL
Active (A-Bank)
Read (A-Bank)
Precharge (A-Bank)
Active (A-Bank)
Write (A-Bank)
Precharge (A-Bank) Don't care
*Note Minimum cycle times required complete internal DRAM operation. precharge interrupt burst cycle. [CAS latency-1] valid output data available after enters precharge. Last valid output will Hi-Z after tSHZ from clock. Access time from address. tCC*(tRCD latency-1) tSAC Output will Hi-Z after burst. (1,2,4 Full page burst, burst wrap-around.
Preliminary (February, 2000, Version 0.0)
AMIC Technology, Inc.
A43L8316
Page Read Write Cycle Same Bank @Burst Length=4
CLOCK
High
tRCD
*Note
ADDR
A8/AP
tCDL tRDL
*Note *Note1 *Note3
(CL=2)
(CL=3)
Active (A-Bank)
Read (A-Bank)
Read (A-Bank)
Write (A-Bank)
Write (A-Bank)
Precharge (A-Bank)
Don't care
*Note write data before burst read ends, should asserted three cycle prior write command avoid contention. precharge will interrupt writing. Last data input, tRDL before precharge, will written. should mask invalid input data precharge command cycle when asserting precharge before burst. Input data after precharge cycle will masked internally.
Preliminary (February, 2000, Version 0.0)
AMIC Technology, Inc.
A43L8316
Page Read Cycle Different Bank @Burst Length
CLOCK
*Note
High
*Note
ADDR
A8/AP
(CL=2)
QAa0 QAa1 QAa2
QAa3 QBb0 QBb1 QBb2 QBb3 QAc0 QAc1 QBd0 QBd1 QAe0 QAe1
(CL=3)
QAa0 QAa1 QAa2
QAa3 QBb0 QBb1 QBb2 QBb3 QAc0 QAc1 QBd0 QBd1 QAe0 QAe1
Active (A-Bank)
Active (B-Bank) Read (A-Bank)
Read (B-Bank)
Read (A-Bank)
Read (B-Bank)
Read (A-Bank)
Precharge (A-Bank)
Don't care
Note don't care when RAS,
high clock high going edge.
interrupt burst read precharge, both read precharge banks must same.
Preliminary (February, 2000, Version 0.0)
AMIC Technology, Inc.
A43L8316
Page Write Cycle Different Bank @Burst Length=4
CLOCK
High
*Note
ADDR
A8/AP
DAa0 DAa1 DAa2
DAa3 DBb0 DBb1 DBb2 DBb3 DAc0 DAc1 DBd0 DBd1 tCDL tRDL
*Note
Active (B-Bank) Active with (A-Bank) Write (A-Bank)
Write (B-Bank)
Write (A-Bank) Write (B-Bank)
Precharge (Both Banks)
Don't care
Note: interrupt burst write precharge, should asserted mask invalid input data. interrupt burst write precharge, both write precharge banks must same.
Preliminary (February, 2000, Version 0.0)
AMIC Technology, Inc.
A43L8316
Read Write Cycle Different Bank @Burst Length=4
CLOCK
High
ADDR
A8/AP
tCDL *Note
(CL=2)
QAa0 QAa1 QAa2 QAa3
DBb0 DBb1 DBb2 DBb3
QAc0 QAc1 QAc2
(CL=3)
QAa0 QAa1 QAa2 QAa3
DBb0 DBb1 DBb2 DBb3
QAc0 QAc1
Active (A-Bank)
Read (A-Bank)
Precharge (A-Bank)
Write (B-Bank)
Read (A-Bank)
Active (B-Bank)
Active (A-Bank) Don't care
Note tCDL should complete write.
Preliminary (February, 2000, Version 0.0)
AMIC Technology, Inc.
A43L8316
Read Write Cycle with Auto Precharge @Burst Length=4
CLOCK
High
ADDR
A8/AP
(CL=2)
QAa0
QAa1 QAa2 QAa3
DBb0 DBb1 DBb2 DBb3
(CL=3)
QAa0 QAa1 QAa2 QAa3
DBb0 DBb1 DBb2 DBb3
Active (A-Bank)
Read with Auto Precharge (A-Bank) Active (B-Bank)
Auto Precharge Start Point (A-Bank)
Write with Auto Precharge (B-Bank)
Auto Precharge Start Point (B-Bank)
Don't care
*Note tRCD should controlled meet minimum tRAS before internal precharge start. case Burst Length=1 BRSW mode)
Preliminary (February, 2000, Version 0.0)
AMIC Technology, Inc.
A43L8316
Read Write Cycle with Auto Precharge @Burst Length=4
CLOCK
High
ADDR
A8/AP
(CL=2)
(CL=3)
Active (A-Bank)
Read with Auto Charge (A-Bank)
Read without Auto Precharge (B-Bank) Auto Precharge Strart Point (A-Bank) *Note
Precharge (B-Bank)
Active (A-Bank)
Write with Auto Precharge (A-Bank)
Active (B-Bank) Don't care
Note
When Read(Write) command with auto precharge issued A-Bank after Bank activation. read(Write) command without auto precharge issued B-Bank before Bank auto precharge starts, Bank auto precharge will start Bank read command input point. command issued Bank during after Bank auto precharge starts.
Preliminary (February, 2000, Version 0.0)
AMIC Technology, Inc.
A43L8316
Read Write Cycle with Auto Precharge @Burst Length=4
CLOCK
High
ADDR
A8/AP
(CL=2)
(CL=3)
Note
Active (A-Bank)
Read with Auto Preharge (A-Bank)
Auto Precharge Read with Start Point Auto Precharge (B-Bank) (A-Bank) Active (B-Bank)
Auto Precharge Start Point (B-Bank)
Don't care
Note command A-bank allowed this period. determined from auto precharge start point
Preliminary (February, 2000, Version 0.0)
AMIC Technology, Inc.
A43L8316
Read Interrupted Precharge Command Read Burst Stop Cycle (@Burst Length Full Page)
CLOCK
High
ADDR
Note Note
A8/AP
Note
(CL=2)
QAa0 QAa1 QAa2 QAa3 QAa4
QAb0 QAb1 QAb2 QAb3 QAb4 QAb5
(CL=3)
QAa0
QAa1 QAa2 QAa3 QAa4
QAb0 QAb1 QAb2 QAb3 QAb4 QAb5
Active (A-Bank)
Read (A-Bank)
Burst Stop
Read (A-Bank)
Precharge (A-Bank)
Don't care
Note full page mode, burst wrap-around burst. auto precharge impossible. About valid DQ's after burst stop, same case interrupt.
Both cases illustrated above timing diagram. label them. burst write, burst stop interrupt should compared carefully. Refer timing diagram "Full page write burst stop cycle". Burst stop valid every burst length.
Preliminary (February, 2000, Version 0.0)
AMIC Technology, Inc.
A43L8316
Write Interrupted Precharge Command Write Burst Stop Cycle Burst Length Full Page)
CLOCK
High
ADDR
Note Note
A8/AP
tBDL tRDL
Note
Note
DAa0
DAa1
DAa2
DAa3 DAa4
DAb0 DAb1 DAb2 DAb3 DAb4 DAb5
Active (A-Bank)
Write (A-Bank)
Burst Stop
Write (A-Bank)
Precharge (A-Bank)
Don't care
Note full page mode, burst wrap-around burst. auto precharge impossible. Data-in cycle burst stop command cannot written into corresponding memory cell. defined parameter tBDL(=1CLK). Data-in cycle interrupted precharge cannot written into corresponding memory cell. defined parameter tRDL(1=CLK). write interrupted precharge command needed ensure tRDL 1CLK. should mask invalid input data precharge command cycle when asserting precharge before burst. Input data after precharge cycle will masked internally. Burst stop valid only every burst length.
Preliminary (February, 2000, Version 0.0)
AMIC Technology, Inc.
A43L8316
Burst Read Single Write Cycle @Burst Length=2, BRSW
CLOCK
High
Note
ADDR
A8/AP
(CL=2)
DAa0
QAb0
QAb1
DBc0
QAd0
QAd1
(CL=3)
DAa0
QAb0 QAb1
DBc0
QAd0
QAd1
Active (A-Bank)
Active (B-Bank)
Active (A-Bank)
Read (A-Bank)
Precharge (A-Bank)
Write (A-Bank)
Read with Auto Precharge (A-Bank)
Write with Auto Precharge (B-Bank) Don't care
Note BRSW mode enabled setting "High" (Mode Register Set). BRSW Mode, burst length write fixed regardless programed burst length. When BRSW write command with auto precharge executed, keep mind that tRAS should violated. Auto precharge executed burst-end cycle, case BRSW write command, next cycle starts precharge.
Preliminary (February, 2000, Version 0.0)
AMIC Technology, Inc.
A43L8316
Clock Suspension Operation Cycle @CAS Latency Burst Length=4
CLOCK
ADDR
A8/AP
Note
tSHZ
tSHZ
Active
Read
Clock Suspension
Read
Read Write
Write Clock Suspension
Don't care
Note needed prevent contention.
Preliminary (February, 2000, Version 0.0)
AMIC Technology, Inc.
A43L8316
Active/Precharge Power Down Mode @CAS Lantency=2, Burst Length=4
CLOCK
Note
Note
*Note
A8/AP
ADDR
Precharge Power-down Entry
Precharge Power-down Exit Active Active Power-down Entry Active Power-down Exit
Note banks should idle state prior entering precharge power down mode. should high least "1CLK tSS" prior active command. Cannot violate minimum refresh specification. (16ms)
Preliminary (February, 2000, Version 0.0)
Read
Precharge
Don't care
AMIC Technology, Inc.
A43L8316
Self Refresh Entry Exit Cycle
CLOCK
Note
Note
Note
Note
Note
Note
min.
Note
Note
Hi-Z
Hi-Z
Self Refresh Entry
Self Refresh Exit
A8/AP
ADDR
Note ENTER SELF REFRESH MODE
with should same clock cycle.
After clock cycle, inputs including system clock don't care except CKE. device remains self refresh mode long stays "Low". (cf.) Once device enters self refresh mode, minimum tRAS required before exit from self refresh. EXIT SELF REFRESH MODE System clock restart stable before returning high. starts from high. Minimum required after going high complete self refresh exit. cycle burst auto refresh required before self refresh entry after self refresh exit. system uses burst refresh.
Preliminary (February, 2000, Version 0.0)
Auto Refresh Don't care
AMIC Technology, Inc.
A43L8316
Mode Register Cycle Auto Refresh Cycle
CLOCK
*Note
High
High
Note
Note
Hi-Z
Hi-Z
Command
Auto Refresh
ADDR
Command Don't care
Both banks precharge should completed before Mode Register cycle auto refresh cycle.
MODE REGISTER CYCLE Note
activation same clock cycle with address will internal
mode register. Minimum clock cycles should before activation.
Please refer Mode Register table.
Preliminary (February, 2000, Version 0.0)
AMIC Technology, Inc.
A43L8316
Function Truth Table (Table
Current State
Address A8/AP Code CA,A8/AP CA,A8/AP CA,A8/AP CA,AP CA,A8/AP CA,A8/AP A8/AP CA,A8/AP CA,A8/AP ILLEGAL ILLEGAL
Action
Note
IDLE
Active; Latch Address Auto Refresh Self Refresh Mode Register Access ILLEGAL Begin Read; Latch Determine Begin Write; Latch Determine ILLEGAL Precharge ILLEGAL NOP(Continue Burst Active) NOP(Continue Burst Active) Term burst Active Term burst; Begin Read; Latch Determine Term burst; Begin Write; Latch Determine ILLEGAL Term Burst; Precharge timing Reads ILLEGAL NOP(Continue Burst EndRow Active) NOP(Continue Burst EndRow Active) ILLEGAL Term burst; Begin Read; Latch Determine Term burst; Begin Read; Latch Determine ILLEGAL Term Burst; Precharge timing Writes ILLEGAL NOP(Continue Burst EndPrecharge) NOP(Continue Burst EndPrecharge) ILLEGAL ILLEGAL ILLEGAL ILLEGAL ILLEGAL
Active
Read
Write
Read with Auto Precharge
Preliminary (February, 2000, Version 0.0)
AMIC Technology, Inc.
A43L8316
Function Truth Table (Table Continued)
Current State
Address CA,A8/AP CA,A8/AP CA,A8/AP CA,A8/AP
Action NOP(Continue Burst EndPrecharge) NOP(Continue Burst EndPrecharge) ILLEGAL ILLEGAL ILLEGAL ILLEGAL ILLEGAL NOPIdle after NOPIdle after ILLEGAL ILLEGAL ILLEGAL NOPIdle after ILLEGAL NOPRow Active after tRCD NOPRow Active after tRCD ILLEGAL ILLEGAL ILLEGAL ILLEGAL ILLEGAL NOPIdle after NOPIdle after ILLEGAL ILLEGAL ILLEGAL
Note
Write with Auto Precharge
Precharge
Activating
Refreshing
Abbreviations Address Operation Command
Bank Address Column Address
Auto Precharge Precharge
Note: entries assume that active (High) during preceding clock cycle current clock cycle. Illegal bank specified state Function legal bank indicated depending state that bank. Must satisfy contention, turn around, and/or write recovery requirements. bank precharging idle state. precharge bank indicated (and PA). Illegal banks idle.
Preliminary (February, 2000, Version 0.0)
AMIC Technology, Inc.
A43L8316
Function Truth Table (Table
Current State Self Refresh Both Bank Precharge Power Down Banks Idle State Other than Listed Above
Address INVALID
Action
Note
Exit Self RefreshABI after Exit Self RefreshABI after ILLEGAL ILLEGAL ILLEGAL NOP(Maintain Self Refresh) INVALID Exit Power DownABI Exit Power DownABI ILLEGAL ILLEGAL ILLEGAL NOP(Maintain Power Down Mode) Refer Table Enter Power Down Enter Power Down ILLEGAL ILLEGAL ILLEGAL Enter Self Refresh ILLEGAL Refer Operations Table Begin Clock Suspend next cycle Exit Clock Suspend next cycle Maintain clock Suspend
Abbreviations Banks Idle Note: After CKE's high transition exit self refresh mode. time tRC(min) elapse after CKE's high transition issue command. high transition asynchronous restarts internal clock. minimum setup time "tSS clock" must satisfied before command other than exit. Power-down self refresh entered only from banks idle state. Must legal command.
Preliminary (February, 2000, Version 0.0)
AMIC Technology, Inc.
A43L8316
Ordering Information
Part A43L8316V-10 Cycle Time (ns) Clock Frequency (MHz) Access Time Package TSOP (II)
Preliminary (February, 2000, Version 0.0)
AMIC Technology, Inc.
A43L8316
Package Information TSOP (Type Outline Dimensions
Detail R0.15 REF.
unit: inches/mm
R0.15 REF. 0.25
Detail
Seating Plane
Dimensions inches
Dimensions 0.05 0.95 0.30 0.12 20.855 11.56 10.06 0.40 1.00 20.955 11.76 10.16 0.800 0.50 0.80 1.20 0.15 1.05 0.45 0.21 21.055 11.96 10.26 0.60
Symbol
0.002 0.037 0.012 0.005 0.821 0.455 0.396 0.016
0.040 0.825 0.463 0.400 0.031 0.020 0.031
0.047 0.041 0.018 0.008 0.829 0.471 0.404 0.024
Notes: maximum value dimension includes flash. Dimension does include resin fins. Dimension includes flash.
Preliminary (February, 2000, Version 0.0)
AMIC Technology, Inc.

Document Title 128K Banks Synchronous DRAM Revision History 128K

Top Searches for this datasheet

Other recent searches