SN54 74LS113A offers individual set, clock inputs. These monolithic du

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

SN54 74LS113A offers individual set, clock inputs. These monolithic du

Datasheet Thumbnail

Top Searches for this datasheet

SN54/74LS113A DUAL NEGATIVE EDGE-TRIGGERED FLIP-FLOP
SN54 74LS113A offers individual set, clock inputs. These monolithic dual flip-flops designed that when clock goes HIGH, inputs enabled data will accepted. logic level inputs allowed change when clock pulse HIGH bistable will perform according truth table long minimum setup times observed. Input data transferred outputs negative-going edge clock pulse.
DUAL NEGATIVE EDGE-TRIGGERED FLIP-FLOP
POWER SCHOTTKY
LOGIC DIAGRAM (Each Flip-Flop)
SUFFIX CERAMIC CASE 632-08
5(9) 6(8)
(SD) 4(10) 3(11) 1(13) CLOCK (CP) 2(12)
SUFFIX PLASTIC CASE 646-06
SUFFIX SOIC CASE 751A-02
ORDERING INFORMATION MODE SELECT TRUTH TABLE
INPUTS OPERATING MODE Toggle Load (Reset) Load (Set) Hold
OUTPUTS
SN54LSXXXJ SN74LSXXXN SN74LSXXXD
Ceramic Plastic SOIC
LOGIC SYMBOL
HIGH Voltage Level Voltage Level Don't Care Lower case letters indicate state referenced input output) set-up time prior HIGH clock transition.
FAST DATA 5-189
SN54/74LS113A
GUARANTEED OPERATING RANGES
Symbol Supply Voltage Operating Ambient Temperature Range Output Current High Output Current Parameter 4.75 5.25 Unit
CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)
Limits Symbol Parameter Input HIGH Voltage Input Voltage Input Clamp Diode Voltage Output HIGH Voltage Output Voltage Clock Input HIGH Current Clock Set, Clock 0.35 0.65 0.25 Unit Test Conditions Guaranteed Input HIGH Voltage Inputs Guaranteed Input Voltage Inputs MIN, MIN, MAX, Truth Table MIN, Truth Table
MAX,
MAX,
Input Current
MAX,
Short Circuit Current (Note Power Supply Current
Note more than output should shorted time, more than second.
CHARACTERISTICS 25°C,
Limits Symbol fMAX tPLH tPHL Parameter Maximum Clock Frequency Propagation Delay, Clock Output Unit Test Conditions
SETUP REQUIREMENTS 25°C,
Limits Symbol Parameter Clock Pulse Width High Pulse Width Setup Time Hold Time Unit Test Conditions
FAST DATA 5-190
Case 751A-02 Suffix 14-Pin Plastic SO-14 -A14
NOTES: DIMENSIONS DATUMS DATUM SURFACE. DIMENSIONING TOLERANCING ANSI Y14.5M, 1982. CONTROLLING DIMENSION: MILLIMETER. DIMENSION INCLUDE MOLD PROTRUSION. MAXIMUM MOLD PROTRUSION 0.15 (0.006) SIDE. 751A OBSOLETE, STANDARD 751A
0.25 (0.010)
SEATING PLANE
0.25 (0.010)
MILLIMETERS
8.55 3.80 1.35 0.35 0.40 8.75 4.00 1.75 0.49 1.25
INCHES
0.337 0.150 0.054 0.014 0.016 0.344 0.157 0.068 0.019 0.049
1.27 0.19 0.10 0.25 0.25
0.050 0.008 0.004 0.009 0.009
5.80 0.25
6.20 0.50
0.229 0.010
0.244 0.019
Case 632-08 Suffix 14-Pin Ceramic Dual In-Line -A14
NOTES: DIMENSIONING TOLERANCING ANSI Y14.5M, 1982. CONTROLLING DIMENSION: INCH.
DIMENSION CENTER LEAD WHEN FORMED PARALLEL. NARROW 0.76 (0.030) WHERE LEAD ENTERS CERAMIC BODY. THRU OBSOLETE, STANDARD
-TSEATING PLANE
0.25 (0.010)
0.25 (0.010)
MILLIMETERS
19.05 6.23 3.94 0.39 1.40 19.94 7.11 5.08 0.50 1.65
INCHES
0.750 0.245 0.155 0.015 0.055 0.785 0.280 0.200 0.020 0.065
2.54 0.21 3.18 0.38 4.31
0.100 0.008 0.125 0.015 0.170
7.62
0.300
0.51
1.01
0.020
0.040
Case 646-06 Suffix 14-Pin Plastic
NOTES: LEADS WITHIN 0.13 (0.005) RADIUS TRUE POSITION SEATING PLANE MAXIMUM MATERIAL CONDITION.
DIMENSION CENTER LEADS WHEN FORMED PARALLEL.
DIMENSION DOES INCLUDE MOLD FLASH.
ROUNDED CORNERS OPTIONAL. OBSOLETE, STANDARD
SEATING PLANE
NOTE
MILLIMETERS
18.16 6.10 3.69 0.38 1.02 19.56 6.60 4.69 0.53 1.78
INCHES
0.715 0.240 0.145 0.015 0.040 0.770 0.260 0.185 0.021 0.070
2.54 1.32 0.20 2.92 2.41 0.38 3.43
0.100 0.052 0.008 0.115 0.095 0.015 0.135
7.62
0.300
0.39
1.01
0.015
0.039
FAST DATA 5-191
Motorola reserves right make changes without further notice products herein. Motorola makes warranty, representation guarantee regarding suitability products particular purpose, does Motorola assume liability arising application product circuit, specifically disclaims liability, including without limitation consequential incidental damages. "Typical" parameters vary different applications. operating parameters, including "Typicals" must validated each customer application customer's technical experts. Motorola does convey license under patent rights rights others. Motorola products designed, intended, authorized components systems intended surgical implant into body, other applications intended support sustain life, other application which failure Motorola product could create situation where personal injury death occur. Should Buyer purchase Motorola products such unintended unauthorized application, Buyer shall indemnify hold Motorola officers, employees, subsidiaries, affiliates, distributors harmless against claims, costs, damages, expenses, reasonable attorney fees arising directly indirectly, claim personal injury death associated with such unintended unauthorized use, even such claim alleges that Motorola negligent regarding design manufacture part. Motorola registered trademarks Motorola, Inc. Motorola, Inc. Equal Opportunity/Affirmative Action Employer.
Literature Distribution Centers: USA: Motorola Literature Distribution; P.O. 20912; Phoenix, Arizona 85036. EUROPE: Motorola Ltd.; European Literature Centre; Tanners Drive, Blakelands, Milton Keynes, MK14 5BP, England. JAPAN: Nippon Motorola Ltd.; 4-32-1, Nishi-Gotanda, Shinagawa-ku, Tokyo 141, Japan. ASIA PACIFIC: Motorola Semiconductors H.K. Ltd.; Silicon Harbour Center, King Street, Industrial Estate, N.T., Hong Kong.
FAST DATA 5-192

SN54 74LS113A offers individual set, clock inputs. These monolithic du

Top Searches for this datasheet

Other recent searches