SN54 74LS107A Dual Flip-Flop with individual Direct Clear Clock Pulse

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

SN54 74LS107A Dual Flip-Flop with individual Direct Clear Clock Pulse

Datasheet Thumbnail

Top Searches for this datasheet

SN54/74LS107A DUAL NEGATIVE EDGE-TRIGGERED FLIP-FLOP
SN54 74LS107A Dual Flip-Flop with individual Direct Clear Clock Pulse inputs. Output changes initiated HIGH-to-LOW transition clock. signal input overrides other inputs makes output LOW. SN54 74LS107A same SN54 74LS73A corner power pins.
DUAL NEGATIVE EDGE-TRIGGERED FLIP-FLOP
POWER SCHOTTKY
CONNECTION DIAGRAM (TOP VIEW)
NOTE: Flatpak version same pinouts (Connection Diagram) Dual In-Line Package.
SUFFIX CERAMIC CASE 632-08
SUFFIX PLASTIC CASE 646-06
LOGIC SYMBOL
SUFFIX SOIC CASE 751A-02
ORDERING INFORMATION
SN54LSXXXJ SN74LSXXXN SN74LSXXXD
Ceramic Plastic SOIC
GUARANTEED OPERATING RANGES
Symbol Supply Voltage Operating Ambient Temperature Range Output Current High Output Current Parameter 4.75 5.25 Unit
FAST DATA 5-177
SN54/74LS107A
CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)
Limits Symbol Parameter Input HIGH Voltage Input Voltage Input Clamp Diode Voltage Output HIGH Voltage Output Voltage Clear Clock Input HIGH Current Clear Clock Input Current Short Circuit Current (Note Power Supply Current Clear Clock -100 MAX, 0.35 0.25 0.65 Unit Test Conditions Guaranteed Input HIGH Voltage Inputs Guaranteed Input Voltage Inputs MIN, MIN, MAX, Truth Table MIN, Truth Table
MAX,
MAX,
Note more than output should shorted time, more than second.
CHARACTERISTICS 25°C,
Limits Symbol fMAX tPLH tPHL Parameter Maximum Clock Frequency Propagation Delay, Clock Output Unit Test Conditions
SETUP REQUIREMENTS 25°C,
Limits Symbol Parameter Clock Pulse Width Clear Pulse Width Setup Time Hold Time Unit Test Conditions
FAST DATA 5-178
Case 751A-02 Suffix 14-Pin Plastic SO-14 -A14
NOTES: DIMENSIONS DATUMS DATUM SURFACE. DIMENSIONING TOLERANCING ANSI Y14.5M, 1982. CONTROLLING DIMENSION: MILLIMETER. DIMENSION INCLUDE MOLD PROTRUSION. MAXIMUM MOLD PROTRUSION 0.15 (0.006) SIDE. 751A OBSOLETE, STANDARD 751A
0.25 (0.010)
SEATING PLANE
0.25 (0.010)
MILLIMETERS
8.55 3.80 1.35 0.35 0.40 8.75 4.00 1.75 0.49 1.25
INCHES
0.337 0.150 0.054 0.014 0.016 0.344 0.157 0.068 0.019 0.049
1.27 0.19 0.10 0.25 0.25
0.050 0.008 0.004 0.009 0.009
5.80 0.25
6.20 0.50
0.229 0.010
0.244 0.019
Case 632-08 Suffix 14-Pin Ceramic Dual In-Line -A14
NOTES: DIMENSIONING TOLERANCING ANSI Y14.5M, 1982. CONTROLLING DIMENSION: INCH.
DIMENSION CENTER LEAD WHEN FORMED PARALLEL. NARROW 0.76 (0.030) WHERE LEAD ENTERS CERAMIC BODY. THRU OBSOLETE, STANDARD
-TSEATING PLANE
0.25 (0.010)
0.25 (0.010)
MILLIMETERS
19.05 6.23 3.94 0.39 1.40 19.94 7.11 5.08 0.50 1.65
INCHES
0.750 0.245 0.155 0.015 0.055 0.785 0.280 0.200 0.020 0.065
2.54 0.21 3.18 0.38 4.31
0.100 0.008 0.125 0.015 0.170
7.62
0.300
0.51
1.01
0.020
0.040
Case 646-06 Suffix 14-Pin Plastic
NOTES: LEADS WITHIN 0.13 (0.005) RADIUS TRUE POSITION SEATING PLANE MAXIMUM MATERIAL CONDITION.
DIMENSION CENTER LEADS WHEN FORMED PARALLEL.
DIMENSION DOES INCLUDE MOLD FLASH.
ROUNDED CORNERS OPTIONAL. OBSOLETE, STANDARD
SEATING PLANE
NOTE
MILLIMETERS
18.16 6.10 3.69 0.38 1.02 19.56 6.60 4.69 0.53 1.78
INCHES
0.715 0.240 0.145 0.015 0.040 0.770 0.260 0.185 0.021 0.070
2.54 1.32 0.20 2.92 2.41 0.38 3.43
0.100 0.052 0.008 0.115 0.095 0.015 0.135
7.62
0.300
0.39
1.01
0.015
0.039
FAST DATA 5-179
Motorola reserves right make changes without further notice products herein. Motorola makes warranty, representation guarantee regarding suitability products particular purpose, does Motorola assume liability arising application product circuit, specifically disclaims liability, including without limitation consequential incidental damages. "Typical" parameters vary different applications. operating parameters, including "Typicals" must validated each customer application customer's technical experts. Motorola does convey license under patent rights rights others. Motorola products designed, intended, authorized components systems intended surgical implant into body, other applications intended support sustain life, other application which failure Motorola product could create situation where personal injury death occur. Should Buyer purchase Motorola products such unintended unauthorized application, Buyer shall indemnify hold Motorola officers, employees, subsidiaries, affiliates, distributors harmless against claims, costs, damages, expenses, reasonable attorney fees arising directly indirectly, claim personal injury death associated with such unintended unauthorized use, even such claim alleges that Motorola negligent regarding design manufacture part. Motorola registered trademarks Motorola, Inc. Motorola, Inc. Equal Opportunity/Affirmative Action Employer.
Literature Distribution Centers: USA: Motorola Literature Distribution; P.O. 20912; Phoenix, Arizona 85036. EUROPE: Motorola Ltd.; European Literature Centre; Tanners Drive, Blakelands, Milton Keynes, MK14 5BP, England. JAPAN: Nippon Motorola Ltd.; 4-32-1, Nishi-Gotanda, Shinagawa-ku, Tokyo 141, Japan. ASIA PACIFIC: Motorola Semiconductors H.K. Ltd.; Silicon Harbour Center, King Street, Industrial Estate, N.T., Hong Kong.
FAST DATA 5-180

SN54 74LS107A Dual Flip-Flop with individual Direct Clear Clock Pulse

Top Searches for this datasheet

Other recent searches