Quad 2-Input Multiplexer MC10H159 quad 2-input multiplexer with e
|
|
|
Top Searches for this datasheet
Quad 2-Input Multiplexer
MC10H159 quad 2-input multiplexer with enable. This MECL part functional/pinout duplication standard MECL family part, with 100% improvement propagation delay increase power-supply current. Propagation Delay, Typical Power Dissipation, Typical Improved Noise Margin (Over Operating Voltage Temperature Range) Voltage Compensated MECL 10K-Compatible
SUFFIX CERAMIC PACKAGE CASE 620-10 SUFFIX PLASTIC PACKAGE CASE 648-08 SUFFIX PLCC CASE 775-02
MC10H159
MAXIMUM RATINGS
Characteristic Power Supply (VCC Input Voltage (VCC Output Current Continuous Surge Operating Temperature Range Storage Temperature Range Plastic Ceramic Symbol Iout Tstg Rating -8.0 +150 +165 Unit Enable Unit IinL -0.735 -1.60 -0.735 -1.45 ENABLE
TRUTH TABLE
Select
ELECTRICAL CHARACTERISTICS (VEE -5.2 ±5%) (See Note)
Characteristic Power Supply Current Input Current High Pins 10-13 Input Current High Output Voltage Output Voltage High Input Voltage Input Voltage Symbol IinH
ASSIGNMENT
SELECT
-1.02 -0.84 -0.98 -0.81 -0.92 -1.95 -1.63 -1.95 -1.63 -1.95 -1.17 -0.84 -1.13 -0.81 -1.07 -1.95 -1.48 -1.95 -1.48 -1.95
PARAMETERS
Propagation Delay Data Select Enable Rise Time Fall Time
NOTE: Each MECL series circuit been designed meet specifications shown test table, after thermal equilibrium been established. circuit test socket mounted printed circuit board transverse flow greater than Iinear maintained. Outputs terminated through 50-ohm resistor -2.0 volts.
assignment Dual-in-Line Package. PLCC assignment, Conversion Tables page 6-11 Motorola MECL Data Book (DL122/D).
3/93
Motorola, Inc. 1996
2-242
MC10H159
APPLICATION INFORMATION
MC10H159 quad channel multiplexer with enable. incorporates common enable common data select inputs. select input determines which data inputs enabled. high level enables data inputs level enables data inputs change data inputs will reflected outputs while enable low. Input levels inverted output.
LOGIC DIAGRAM
SELECT
ENABLE
MECL Data DL122
2-243
MC10H159
OUTLINE DIMENSIONS
SUFFIX PLASTIC PLCC PACKAGE CASE 775-02 ISSUE
0.007 (0.180)
0.007 (0.180)
VIEW
0.010 (0.250)
0.007 (0.180) 0.007 (0.180)
0.007 (0.180)
0.004 (0.100) 0.010 (0.250)
SEATING PLANE
VIEW 0.007 (0.180)
VIEW
NOTES: DATUMS -L-, -M-, DETERMINED WHERE LEAD SHOULDER EXITS PLASTIC BODY MOLD PARTING LINE. DIMENSION TRUE POSITION MEASURED DATUM -T-, SEATING PLANE. DIMENSIONS INCLUDE MOLD FLASH. ALLOWABLE MOLD FLASH 0.010 (0.250) SIDE. DIMENSIONING TOLERANCING ANSI Y14.5M, 1982. CONTROLLING DIMENSION: INCH. PACKAGE SMALLER THAN PACKAGE BOTTOM 0.012 (0.300). DIMENSIONS DETERMINED OUTERMOST EXTREMES PLASTIC BODY EXCLUSIVE MOLD FLASH, BURRS, GATE BURRS INTERLEAD FLASH, INCLUDING MISMATCH BETWEEN BOTTOM PLASTIC BODY. DIMENSION DOES INCLUDE DAMBAR PROTRUSION INTRUSION. DAMBAR PROTRUSION(S) SHALL CAUSE DIMENSION GREATER THAN 0.037 (0.940). DAMBAR INTRUSION(S) SHALL CAUSE DIMENSION SMALLER THAN 0.025 (0.635).
INCHES 0.385 0.395 0.385 0.395 0.165 0.180 0.090 0.110 0.013 0.019 0.050 0.026 0.032 0.020 0.025 0.350 0.356 0.350 0.356 0.042 0.048 0.042 0.048 0.042 0.056 0.020 0.310 0.330 0.040
MILLIMETERS 9.78 10.03 9.78 10.03 4.20 4.57 2.29 2.79 0.33 0.48 1.27 0.66 0.81 0.51 0.64 8.89 9.04 8.89 9.04 1.07 1.21 1.07 1.21 1.07 1.42 0.50 7.88 8.38 1.02
2-244
MECL Data DL122
MC10H159
OUTLINE DIMENSIONS
SUFFIX CERAMIC PACKAGE CASE 620-10 ISSUE
NOTES: DIMENSIONING TOLERANCING ANSI Y14.5M, 1982. CONTROLLING DIMENSION: INCH. DIMENSION CENTER LEAD WHEN FORMED PARALLEL. DIMENSION NARROW 0.76 (0.030) WHERE LEAD ENTERS CERAMIC BODY. INCHES 0.750 0.785 0.240 0.295 0.200 0.015 0.020 0.050 0.055 0.065 0.100 0.008 0.015 0.125 0.170 0.300 0.020 0.040 MILLIMETERS 19.05 19.93 6.10 7.49 5.08 0.39 0.50 1.27 1.40 1.65 2.54 0.21 0.38 3.18 4.31 7.62 0.51 1.01
SEATING PLANE
0.25 (0.010)
0.25 (0.010)
SUFFIX PLASTIC PACKAGE CASE 648-08 ISSUE
NOTES: DIMENSIONING TOLERANCING ANSI Y14.5M, 1982. CONTROLLING DIMENSION: INCH. DIMENSION CENTER LEADS WHEN FORMED PARALLEL. DIMENSION DOES INCLUDE MOLD FLASH. ROUNDED CORNERS OPTIONAL. INCHES 0.740 0.770 0.250 0.270 0.145 0.175 0.015 0.021 0.040 0.70 0.100 0.050 0.008 0.015 0.110 0.130 0.295 0.305 0.020 0.040 MILLIMETERS 18.80 19.55 6.35 6.85 3.69 4.44 0.39 0.53 1.02 1.77 2.54 1.27 0.21 0.38 2.80 3.30 7.50 7.74 0.51 1.01
SEATING PLANE
0.25 (0.010)
Motorola reserves right make changes without further notice products herein. Motorola makes warranty, representation guarantee regarding suitability products particular purpose, does Motorola assume liability arising application product circuit, specifically disclaims liability, including without limitation consequential incidental damages. "Typical" parameters which provided Motorola data sheets and/or specifications vary different applications actual performance vary over time. operating parameters, including "Typicals" must validated each customer application customer's technical experts. Motorola does convey license under patent rights rights others. Motorola products designed, intended, authorized components systems intended surgical implant into body, other applications intended support sustain life, other application which failure Motorola product could create situation where personal injury death occur. Should Buyer purchase Motorola products such unintended unauthorized application, Buyer shall indemnify hold Motorola officers, employees, subsidiaries, affiliates, distributors harmless against claims, costs, damages, expenses, reasonable attorney fees arising directly indirectly, claim personal injury death associated with such unintended unauthorized use, even such claim alleges that Motorola negligent regarding design manufacture part. Motorola registered trademarks Motorola, Inc. Motorola, Inc. Equal Opportunity/Affirmative Action Employer. reach USA/EUROPE/Locations Listed: Motorola Literature Distribution; P.O. 20912; Phoenix, Arizona 85036. 1-800-441-2447 602-303-5454 MFAX: RMFAX0@email.sps.mot.com TOUCHTONE 602-244-6609 INTERNET: http://Design-NET.com
JAPAN: Nippon Motorola Ltd.; Tatsumi-SPD-JLDC, Seibu-Butsuryu-Center, 3-14-2 Tatsumi Koto-Ku, Tokyo 135, Japan. 03-81-3521-8315 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; Ping Industrial Park, Ting Road, N.T., Hong Kong. 852-26629298
MECL Data DL122 2-245
*MC10H159/D*
MC10H159/D
Other recent searches
TS902 - TS902 TS902 Datasheet
TC35823F - TC35823F TC35823F Datasheet
FR1601G - FR1601G FR1601G Datasheet
FR1607G - FR1607G FR1607G Datasheet
FD059U06A5B - FD059U06A5B FD059U06A5B Datasheet
APED3528ZGC-F01 - APED3528ZGC-F01 APED3528ZGC-F01 Datasheet
APB3025CGKQWDF-AT - APB3025CGKQWDF-AT APB3025CGKQWDF-AT Datasheet
Privacy Policy | Disclaimer
© 2012 Datasheet Archive
