Quad Driver MC10192 contains four line drivers with complementary

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

Quad Driver MC10192 contains four line drivers with complementary

Datasheet Thumbnail

Top Searches for this datasheet

Quad Driver
MC10192 contains four line drivers with complementary outputs. Each driver Data input shares Enable input with another driver. driver outputs uncommitted collectors pair transistors operating current switch. Each driver accepts MECL input signals provides nominal signal swing across load each output collector. Outputs drive higher values load resistance, provided that combination drop load return voltage does cause output collector more negative than -2.4 with respect VCC. avoid output transistor breakdown, load return voltage should more positive than +5.5 with respect VCC. When input high, both output transistors driver nonconducting. When used, inputs, well inputs, left open. Open Collector Outputs Drive Terminated Lines Transformers Input Pulldown Resistors Inputs (Unused Inputs Left Open) Power Dissipation typ/pkg Load) Propagation Delay= Output) Output)
MC10192
SUFFIX CERAMIC PACKAGE CASE 620-10 SUFFIX PLASTIC PACKAGE CASE 648-08 SUFFIX PLCC CASE 775-02
ASSIGNMENT LOGIC DIAGRAM
assignment Dual-in-Line Package. PLCC assignment, Conversion Tables page 6-11 Motorola MECL Data Book (DL122/D).
TRUTH TABLE Inputs Output
Note: Unused outputs must terminated proper operation.
3/93
Motorola, Inc. 1996
3-160
MC10192
ELECTRICAL CHARACTERISTICS
Test Limits Under Test 13.5 13.3 -2.4 13.5 18.0 14.0 13.9 14.0 -30°C 18.0 14.0 13.3 14.0 19.0 +25°C +85°C Unit mAdc µAdc µAdc mAdc mAdc mAdc mAdc mAdc tPHL tPLH tTLH tTHL
Characteristic Power Supply Drain Current Input Current
Symbol IinH IinL
Output Current High Output Current Threshold Current High Threshold Current Output Sink Current
Logic Logic Logic Logic Logic
IOHC IOLC VOLS
Load Return Voltage Absolute Rating (Note Output Voltage (Note Switching Times Propagation Delay Rise/Fall Time Load) Output Output 80%)
5.5V value maximum rating, exceed. resistor will prevent output transistor breakdown. Limitations load resistor load return voltage combinations. Refer page 3-160 description.
ELECTRICAL CHARACTERISTICS (continued)
TEST VOLTAGE VALUES (Volts) Test Temperature -30°C +25°C +85°C Under Test 5,10,11 5,6,10,11 5,6,10,11 5,7,9,10,11 5,6,10,11 VIHmax -0.890 -0.810 -0.700 VILmin -1.890 -1.850 -1.825 VIHAmin -1.205 -1.105 -1.035 VILAmax -1.500 -1.475 -1.440 -5.2 -5.2 -5.2 (VCC)
TEST VOLTAGE APPLIED PINS LISTED BELOW VIHmax VILmin VIHAmin VILAmax
Characteristic Power Supply Drain Current Input Current
Symbol IinH IinL
Output Current High Output Current Threshold Current High Threshold Current Output Sink Current
Logic Logic Logic Logic Logic
IOHC IOLC VOLS
Load Return Voltage Absolute Rating (Note Output Voltage (Note
Each MECL 10,000 series circuit been designed meet specifications shown test table, after thermal equilibrium been established. circuit test socket mounted printed circuit board transverse flow greater than linear maintained. Outputs terminated through 50-ohm resistor -2.0 volts. Test procedures shown only gate. other gates tested same manner.
MECL Data DL122
3-161
MC10192
OUTLINE DIMENSIONS
SUFFIX PLASTIC PLCC PACKAGE CASE 775-02 ISSUE
0.007 (0.180)
0.007 (0.180)
VIEW
0.010 (0.250)
0.007 (0.180) 0.007 (0.180)
0.007 (0.180)
0.004 (0.100) 0.010 (0.250)
SEATING PLANE
VIEW 0.007 (0.180)
VIEW
NOTES: DATUMS -L-, -M-, DETERMINED WHERE LEAD SHOULDER EXITS PLASTIC BODY MOLD PARTING LINE. DIMENSION TRUE POSITION MEASURED DATUM -T-, SEATING PLANE. DIMENSIONS INCLUDE MOLD FLASH. ALLOWABLE MOLD FLASH 0.010 (0.250) SIDE. DIMENSIONING TOLERANCING ANSI Y14.5M, 1982. CONTROLLING DIMENSION: INCH. PACKAGE SMALLER THAN PACKAGE BOTTOM 0.012 (0.300). DIMENSIONS DETERMINED OUTERMOST EXTREMES PLASTIC BODY EXCLUSIVE MOLD FLASH, BURRS, GATE BURRS INTERLEAD FLASH, INCLUDING MISMATCH BETWEEN BOTTOM PLASTIC BODY. DIMENSION DOES INCLUDE DAMBAR PROTRUSION INTRUSION. DAMBAR PROTRUSION(S) SHALL CAUSE DIMENSION GREATER THAN 0.037 (0.940). DAMBAR INTRUSION(S) SHALL CAUSE DIMENSION SMALLER THAN 0.025 (0.635).
INCHES 0.385 0.395 0.385 0.395 0.165 0.180 0.090 0.110 0.013 0.019 0.050 0.026 0.032 0.020 0.025 0.350 0.356 0.350 0.356 0.042 0.048 0.042 0.048 0.042 0.056 0.020 0.310 0.330 0.040
MILLIMETERS 9.78 10.03 9.78 10.03 4.20 4.57 2.29 2.79 0.33 0.48 1.27 0.66 0.81 0.51 0.64 8.89 9.04 8.89 9.04 1.07 1.21 1.07 1.21 1.07 1.42 0.50 7.88 8.38 1.02
3-162
MECL Data DL122
MC10192
OUTLINE DIMENSIONS
SUFFIX CERAMIC PACKAGE CASE 620-10 ISSUE
NOTES: DIMENSIONING TOLERANCING ANSI Y14.5M, 1982. CONTROLLING DIMENSION: INCH. DIMENSION CENTER LEAD WHEN FORMED PARALLEL. DIMENSION NARROW 0.76 (0.030) WHERE LEAD ENTERS CERAMIC BODY. INCHES 0.750 0.785 0.240 0.295 0.200 0.015 0.020 0.050 0.055 0.065 0.100 0.008 0.015 0.125 0.170 0.300 0.020 0.040 MILLIMETERS 19.05 19.93 6.10 7.49 5.08 0.39 0.50 1.27 1.40 1.65 2.54 0.21 0.38 3.18 4.31 7.62 0.51 1.01
SEATING PLANE
0.25 (0.010)
0.25 (0.010)
SUFFIX PLASTIC PACKAGE CASE 648-08 ISSUE
NOTES: DIMENSIONING TOLERANCING ANSI Y14.5M, 1982. CONTROLLING DIMENSION: INCH. DIMENSION CENTER LEADS WHEN FORMED PARALLEL. DIMENSION DOES INCLUDE MOLD FLASH. ROUNDED CORNERS OPTIONAL. INCHES 0.740 0.770 0.250 0.270 0.145 0.175 0.015 0.021 0.040 0.70 0.100 0.050 0.008 0.015 0.110 0.130 0.295 0.305 0.020 0.040 MILLIMETERS 18.80 19.55 6.35 6.85 3.69 4.44 0.39 0.53 1.02 1.77 2.54 1.27 0.21 0.38 2.80 3.30 7.50 7.74 0.51 1.01
SEATING PLANE
0.25 (0.010)
Motorola reserves right make changes without further notice products herein. Motorola makes warranty, representation guarantee regarding suitability products particular purpose, does Motorola assume liability arising application product circuit, specifically disclaims liability, including without limitation consequential incidental damages. "Typical" parameters which provided Motorola data sheets and/or specifications vary different applications actual performance vary over time. operating parameters, including "Typicals" must validated each customer application customer's technical experts. Motorola does convey license under patent rights rights others. Motorola products designed, intended, authorized components systems intended surgical implant into body, other applications intended support sustain life, other application which failure Motorola product could create situation where personal injury death occur. Should Buyer purchase Motorola products such unintended unauthorized application, Buyer shall indemnify hold Motorola officers, employees, subsidiaries, affiliates, distributors harmless against claims, costs, damages, expenses, reasonable attorney fees arising directly indirectly, claim personal injury death associated with such unintended unauthorized use, even such claim alleges that Motorola negligent regarding design manufacture part. Motorola registered trademarks Motorola, Inc. Motorola, Inc. Equal Opportunity/Affirmative Action Employer. reach USA/EUROPE/Locations Listed: Motorola Literature Distribution; P.O. 5405, Denver, Colorado 80217. 303-675-2140 1-800-441-2447 MfaxTM: RMFAX0@email.sps.mot.com TOUCHTONE 602-244-6609 INTERNET: http://Design-NET.com
JAPAN: Nippon Motorola Ltd.; Tatsumi-SPD-JLDC, Seibu-Butsuryu-Center, 3-14-2 Tatsumi Koto-Ku, Tokyo 135, Japan. 81-3-3521-8315 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; Ping Industrial Park, Ting Road, N.T., Hong Kong. 852-26629298
MECL Data DL122 3-163
*MC10192/D*
MC10192/D

Quad Driver MC10192 contains four line drivers with complementary

Top Searches for this datasheet

Other recent searches